tg3: Move phylib report to end of tg3_init_one

Currently, phylib reports appear with a eth%d prefix.  Move the line
after register_netdev() and place it alongside the other informative
messages.  Update nearby informative messages accordingly.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
index 978d1f0ccb7d5b93152b4c1e048501bce7aeb248..aebc645a3b511cab469052cd4892b3a8d4774960 100644 (file)
--- a/drivers/net/tg3.c
+++ b/drivers/net/tg3.c
@@ -1360,10 +1360,6 @@ static int tg3_phy_init(struct tg3 *tp)
 
        phydev->advertising = phydev->supported;
 
-       printk(KERN_INFO
-              "%s: attached PHY driver [%s] (mii_bus:phy_addr=%s)\n",
-              tp->dev->name, phydev->drv->name, phydev->dev.bus_id);
-
        return 0;
 }
 
@@ -13547,26 +13543,34 @@ static int __devinit tg3_init_one(struct pci_dev *pdev,
                goto err_out_apeunmap;
        }
 
-       printk(KERN_INFO "%s: Tigon3 [partno(%s) rev %04x PHY(%s)] "
-              "(%s) %s Ethernet %pM\n",
+       printk(KERN_INFO "%s: Tigon3 [partno(%s) rev %04x] (%s) MAC address %pM\n",
               dev->name,
               tp->board_part_number,
               tp->pci_chip_rev_id,
-              tg3_phy_string(tp),
               tg3_bus_string(tp, str),
-              ((tp->tg3_flags & TG3_FLAG_10_100_ONLY) ? "10/100Base-TX" :
-               ((tp->tg3_flags2 & TG3_FLG2_ANY_SERDES) ? "1000Base-SX" :
-                "10/100/1000Base-T")),
               dev->dev_addr);
 
-       printk(KERN_INFO "%s: RXcsums[%d] LinkChgREG[%d] "
-              "MIirq[%d] ASF[%d] WireSpeed[%d] TSOcap[%d]\n",
+       if (tp->tg3_flags3 & TG3_FLG3_PHY_CONNECTED)
+               printk(KERN_INFO
+                      "%s: attached PHY driver [%s] (mii_bus:phy_addr=%s)\n",
+                      tp->dev->name,
+                      tp->mdio_bus->phy_map[PHY_ADDR]->drv->name,
+                      tp->mdio_bus->phy_map[PHY_ADDR]->dev.bus_id);
+       else
+               printk(KERN_INFO
+                      "%s: attached PHY is %s (%s Ethernet) (WireSpeed[%d])\n",
+                      tp->dev->name, tg3_phy_string(tp),
+                      ((tp->tg3_flags & TG3_FLAG_10_100_ONLY) ? "10/100Base-TX" :
+                       ((tp->tg3_flags2 & TG3_FLG2_ANY_SERDES) ? "1000Base-SX" :
+                        "10/100/1000Base-T")),
+                      (tp->tg3_flags2 & TG3_FLG2_NO_ETH_WIRE_SPEED) == 0);
+
+       printk(KERN_INFO "%s: RXcsums[%d] LinkChgREG[%d] MIirq[%d] ASF[%d] TSOcap[%d]\n",
               dev->name,
               (tp->tg3_flags & TG3_FLAG_RX_CHECKSUMS) != 0,
               (tp->tg3_flags & TG3_FLAG_USE_LINKCHG_REG) != 0,
               (tp->tg3_flags & TG3_FLAG_USE_MI_INTERRUPT) != 0,
               (tp->tg3_flags & TG3_FLAG_ENABLE_ASF) != 0,
-              (tp->tg3_flags2 & TG3_FLG2_NO_ETH_WIRE_SPEED) == 0,
               (tp->tg3_flags2 & TG3_FLG2_TSO_CAPABLE) != 0);
        printk(KERN_INFO "%s: dma_rwctrl[%08x] dma_mask[%d-bit]\n",
               dev->name, tp->dma_rwctrl,