--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2006-2010
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ */
+
+/*
+ * mpc8349emds board configuration file
+ *
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 Family */
+
+#define CONFIG_PCI_66M
+#ifdef CONFIG_PCI_66M
+#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
+#else
+#define CONFIG_83XX_CLKIN 33000000 /* in Hz */
+#endif
+
+#ifdef CONFIG_PCISLAVE
+#define CONFIG_83XX_PCICLK 66666666 /* in Hz */
+#endif /* CONFIG_PCISLAVE */
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#ifdef CONFIG_PCI_66M
+#define CONFIG_SYS_CLK_FREQ 66000000
+#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
+#else
+#define CONFIG_SYS_CLK_FREQ 33000000
+#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
+#endif
+#endif
+
+#define CONFIG_SYS_IMMR 0xE0000000
+
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x00100000
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_DDR_ECC /* support DDR ECC function */
+#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
+#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
+
+/*
+ * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver
+ * unselect it to use old spd_sdram.c
+ */
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS1 0x52
+#define SPD_EEPROM_ADDRESS2 0x51
+#define CONFIG_DIMM_SLOTS_PER_CTLR 2
+#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+/*
+ * 32-bit data path mode.
+ *
+ * Please note that using this mode for devices with the real density of 64-bit
+ * effectively reduces the amount of available memory due to the effect of
+ * wrapping around while translating address to row/columns, for example in the
+ * 256MB module the upper 128MB get aliased with contents of the lower
+ * 128MB); normally this define should be used for devices with real 32-bit
+ * data path.
+ */
+#undef CONFIG_DDR_32BIT
+
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
+ | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#undef CONFIG_DDR_2T_TIMING
+
+/*
+ * DDRCDR - DDR Control Driver Register
+ */
+#define CONFIG_SYS_DDRCDR_VALUE 0x80080001
+
+#if defined(CONFIG_SPD_EEPROM)
+/*
+ * Determine DDR configuration from I2C interface.
+ */
+#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+#else
+/*
+ * Manually set up DDR parameters
+ */
+#define CONFIG_SYS_DDR_SIZE 256 /* MB */
+#if defined(CONFIG_DDR_II)
+#define CONFIG_SYS_DDRCDR 0x80080001
+#define CONFIG_SYS_DDR_CS2_BNDS 0x0000000f
+#define CONFIG_SYS_DDR_CS2_CONFIG 0x80330102
+#define CONFIG_SYS_DDR_TIMING_0 0x00220802
+#define CONFIG_SYS_DDR_TIMING_1 0x38357322
+#define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_CLK_CNTL 0x02000000
+#define CONFIG_SYS_DDR_MODE 0x47d00432
+#define CONFIG_SYS_DDR_MODE2 0x8000c000
+#define CONFIG_SYS_DDR_INTERVAL 0x03cf0080
+#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
+#else
+#define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \
+ | CSCONFIG_ROW_BIT_13 \
+ | CSCONFIG_COL_BIT_10)
+#define CONFIG_SYS_DDR_TIMING_1 0x36332321
+#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
+#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
+#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */
+
+#if defined(CONFIG_DDR_32BIT)
+/* set burst length to 8 for 32-bit data path */
+ /* DLL,normal,seq,4/2.5, 8 burst len */
+#define CONFIG_SYS_DDR_MODE 0x00000023
+#else
+/* the default burst length is 4 - for 64-bit data path */
+ /* DLL,normal,seq,4/2.5, 4 burst len */
+#define CONFIG_SYS_DDR_MODE 0x00000022
+#endif
+#endif
+#endif
+
+/*
+ * SDRAM on the Local Bus
+ */
+#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */
+#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */
+#define CONFIG_SYS_FLASH_SIZE 32 /* max flash size in MB */
+
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
+ | BR_PS_16 /* 16 bit port */ \
+ | BR_MS_GPCM /* MSEL = GPCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+ | OR_UPM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_TRLX_SET \
+ | OR_GPCM_EHTR_SET \
+ | OR_GPCM_EAD)
+
+ /* window base at flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#else
+#undef CONFIG_SYS_RAMBOOT
+#endif
+
+/*
+ * BCSR register on local bus 32KB, 8-bit wide for MDS config reg
+ */
+#define CONFIG_SYS_BCSR 0xE2400000
+ /* Access window base at BCSR base */
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR
+#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
+#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \
+ | BR_PS_8 \
+ | BR_MS_GPCM \
+ | BR_V)
+ /* 0x00000801 */
+#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \
+ | OR_GPCM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_TRLX_CLEAR \
+ | OR_GPCM_EHTR_CLEAR)
+ /* 0xFFFFE8F0 */
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
+
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
+
+/*
+ * Local Bus LCRR and LBCR regs
+ * LCRR: DLL bypass, Clock divider is 4
+ * External Local Bus rate is
+ * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
+ */
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
+#define CONFIG_SYS_LBC_LBCR 0x00000000
+
+/*
+ * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory.
+ */
+
+/* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ * port-size = 32-bits = BR2[19:20] = 11
+ * no parity checking = BR2[21:22] = 00
+ * SDRAM for MSEL = BR2[24:26] = 011
+ * Valid = BR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
+ */
+
+#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_LBC_SDRAM_BASE \
+ | BR_PS_32 /* 32-bit port */ \
+ | BR_MS_SDRAM /* MSEL = SDRAM */ \
+ | BR_V) /* Valid */
+ /* 0xF0001861 */
+#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
+
+/*
+ * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ * 64MB mask for AM, OR2[0:7] = 1111 1100
+ * XAM, OR2[17:18] = 11
+ * 9 columns OR2[19-21] = 010
+ * 13 rows OR2[23-25] = 100
+ * EAD set for extra time OR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
+ */
+
+#define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB \
+ | OR_SDRAM_XAM \
+ | ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
+ | ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
+ | OR_SDRAM_EAD)
+ /* 0xFC006901 */
+
+ /* LB sdram refresh timer, about 6us */
+#define CONFIG_SYS_LBC_LSRT 0x32000000
+ /* LB refresh timer prescal, 266MHz/32 */
+#define CONFIG_SYS_LBC_MRTPR 0x20000000
+
+#define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \
+ | LSDMR_BSMA1516 \
+ | LSDMR_RFCR8 \
+ | LSDMR_PRETOACT6 \
+ | LSDMR_ACTTORW3 \
+ | LSDMR_BL8 \
+ | LSDMR_WRC3 \
+ | LSDMR_CL3)
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
+#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
+#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
+#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
+#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
+
+/* SPI */
+#undef CONFIG_SOFT_SPI /* SPI bit-banged */
+
+/* GPIOs. Used as SPI chip selects */
+#define CONFIG_SYS_GPIO1_PRELIM
+#define CONFIG_SYS_GPIO1_DIR 0xC0000000 /* SPI CS on 0, LED on 1 */
+#define CONFIG_SYS_GPIO1_DAT 0xC0000000 /* Both are active LOW */
+
+/* TSEC */
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
+
+/* USB */
+#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
+
+#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
+#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
+#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
+#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
+#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
+#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
+
+#if defined(CONFIG_PCI)
+
+#define PCI_ONE_PCI1
+#if defined(PCI_64BIT)
+#undef PCI_ALL_PCI1
+#undef PCI_TWO_PCI1
+#undef PCI_ONE_PCI1
+#endif
+
+#define CONFIG_83XX_PCI_STREAMING
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+ #define PCI_ENET0_IOADDR 0xFIXME
+ #define PCI_ENET0_MEMADDR 0xFIXME
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+#endif
+
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+
+#endif /* CONFIG_PCI */
+
+/*
+ * TSEC configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#define CONFIG_GMII 1 /* MII PHY management */
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "TSEC1"
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 1
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC0"
+
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * Configure on-board RTC
+ */
+#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
+
+/*
+ * Environment
+ */
+#ifndef CONFIG_SYS_RAMBOOT
+ #define CONFIG_ENV_ADDR \
+ (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+ #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+ #define CONFIG_ENV_SIZE 0x2000
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+#else
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+/*
+ * Command line configuration.
+ */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+ /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
+
+#if 1 /*528/264*/
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_1X1 |\
+ HRCWL_CSB_TO_CLKIN |\
+ HRCWL_VCO_1X2 |\
+ HRCWL_CORE_TO_CSB_2X1)
+#elif 0 /*396/132*/
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_1X1 |\
+ HRCWL_CSB_TO_CLKIN |\
+ HRCWL_VCO_1X4 |\
+ HRCWL_CORE_TO_CSB_3X1)
+#elif 0 /*264/132*/
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_1X1 |\
+ HRCWL_CSB_TO_CLKIN |\
+ HRCWL_VCO_1X4 |\
+ HRCWL_CORE_TO_CSB_2X1)
+#elif 0 /*132/132*/
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_1X1 |\
+ HRCWL_CSB_TO_CLKIN |\
+ HRCWL_VCO_1X4 |\
+ HRCWL_CORE_TO_CSB_1X1)
+#elif 0 /*264/264 */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_1X1 |\
+ HRCWL_CSB_TO_CLKIN |\
+ HRCWL_VCO_1X4 |\
+ HRCWL_CORE_TO_CSB_1X1)
+#endif
+
+#ifdef CONFIG_PCISLAVE
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_AGENT |\
+ HRCWH_64_BIT_PCI |\
+ HRCWH_PCI1_ARBITER_DISABLE |\
+ HRCWH_PCI2_ARBITER_DISABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_TSEC1M_IN_GMII |\
+ HRCWH_TSEC2M_IN_GMII)
+#else
+#if defined(PCI_64BIT)
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_64_BIT_PCI |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_PCI2_ARBITER_DISABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_TSEC1M_IN_GMII |\
+ HRCWH_TSEC2M_IN_GMII)
+#else
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_32_BIT_PCI |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_PCI2_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_TSEC1M_IN_GMII |\
+ HRCWH_TSEC2M_IN_GMII)
+#endif /* PCI_64BIT */
+#endif /* CONFIG_PCISLAVE */
+
+/*
+ * System performance
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
+#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
+#define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */
+#define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH 0
+#define CONFIG_SYS_SICRL SICRL_LDP_A
+
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \
+ | HID0_ENABLE_INSTRUCTION_CACHE)
+
+/* #define CONFIG_SYS_HID0_FINAL (\
+ HID0_ENABLE_INSTRUCTION_CACHE |\
+ HID0_ENABLE_M_BIT |\
+ HID0_ENABLE_ADDRESS_BROADCAST) */
+
+#define CONFIG_SYS_HID2 HID2_HBE
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
+ | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+
+/* PCI @ 0x80000000 */
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \
+ | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
+ | BATL_PP_RW \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#else
+#define CONFIG_SYS_IBAT1L (0)
+#define CONFIG_SYS_IBAT1U (0)
+#define CONFIG_SYS_IBAT2L (0)
+#define CONFIG_SYS_IBAT2U (0)
+#endif
+
+#ifdef CONFIG_MPC83XX_PCI2
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \
+ | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \
+ | BATL_PP_RW \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#else
+#define CONFIG_SYS_IBAT3L (0)
+#define CONFIG_SYS_IBAT3U (0)
+#define CONFIG_SYS_IBAT4L (0)
+#define CONFIG_SYS_IBAT4U (0)
+#endif
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
+ | BATL_PP_RW \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+
+/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CONFIG_SYS_IBAT6L (0xF0000000 \
+ | BATL_PP_RW \
+ | BATL_MEMCOHERENCE \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U (0xF0000000 \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH0
+#endif
+
+#define CONFIG_HOSTNAME "mpc8349emds"
+#define CONFIG_ROOTPATH "/nfsroot/rootfs"
+#define CONFIG_BOOTFILE "uImage"
+
+#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
+ "echo"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "hostname=mpc8349emds\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+ "flash_nfs=run nfsargs addip addtty;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip addtty;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
+ "bootm\0" \
+ "load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \
+ "update=protect off fe000000 fe03ffff; " \
+ "era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\
+ "upd=run load update\0" \
+ "fdtaddr=780000\0" \
+ "fdtfile=mpc834x_mds.dtb\0" \
+ ""
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
+ "$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+#endif /* __CONFIG_H */
projects / project / bcm63xx / u-boot.git / commitdiff