octeon: add support for Ubiquiti EdgeRouter 4

Ubiquiti EdgeRouter 4 is 4 port Octeon Cavium 7130 powered router.
It has internal power supply and needs c13 power cord.
There are three 10/100/1000 Mbps RJ45/Copper ports and
one 1000 Mbps SFP port connected directly to a SoC.

SoC:
  Octeon Cavium 7130 (Cavium 3)
  Clocked at 1000Mhz

Memory:
  1 GiB (SK hynix H5TQ4G63CFR-RDC × 2)
  DDR3, clocked at 533 Mhz (1066Mhz effective)
Flash:
  - mtd:
    8 MiB (Macronix MX25L6408EMI-12G)
    used for uboot/eeprom
  - emmc:
    4 GiB (SanDisk SDIN7DP2-4G)
    used for kernel+rootfs
Leds: 1x for power status (white/blue, controllable)
  and 4x for ethernet and sfp ports (no control over them)
Buttons: 1x Reset (from SOC)
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 (from SoC)
USB: 1x USB3.0 on front panel (from SoC)
MII: 1x QSGMII from SoC is used
PHY: 1x Vitesse VSC8504 of which 4x ports is used

All physical port numbers are properly mapped inside OS and
named by lanX instead of ethX.

There is also special purpose four(4) loopX ports available.
That loopX ports are currently hardcoded by linux kernel
and exact use case of them is currently unknown. We leave them
to the linux kernel and octeon board defaults.

All four (4) physical ports are connected to the same QSGMII.
vsc8504 is used for phys and only 4, 5, 6 and 7 phys are used.

Phy mapping:
 - Phy5 is connected to physical eth0 port
 - Phy6 is connected to physical eth1 port
 - Phy7 is connected to physical eth2 port
 - Phy4 is connected to physical eth3 port

Why this device needs external dts:
 - faster boot time since need to initialize less device tree nodes.
 - to add actual indication with LED about boot/failure/upgrade.
   i.e. user could know when to enter failsafe mode or if upgrade is done
 - reset button support so user can reset their device in case off failure
 - sfp port indication in dmesg with information about sfp module
   it also indicates when module inserted or removed

Octeon quirks:
 - There is no port status available before it interface brought up
 - SFP port can not be tied to actual phy due to octeon-ethernet state
   and currently we can only get reports a about SFP state in dmesg

How to flash the firmware:
  - copy openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin and
    openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar to
    USB flash drive that is formatted to vfat/fat32
  - connect USB flash drive to edgerouter 4 front USB port
  - connect serial cable using front RJ45 port (115200 baud, 8N1)
  - connect power to cable to edgerouter 4
  - connect terminal to the console to see uboot boot process
  - interrupt boot by pressing button(s) on your keyboard to log in to the uboot
  - detect usb connected flash drives by typing to the console:
    usb start
  - after drive is detected load initramfs+kernel to the memory by typing:
    fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin
  - after initramfs+kernel is loaded to the memory load it by typing:
    bootoctlinux 0 numcores=4 endbootargs mem=0
  - boot process should finish and you will be greeted with console after pressing enter
  - create directory to mount usb flash drive to by typing:
    mkdir /tmp/sda
  - mount flash drive to that directory by typing:
    mount /dev/sda1 /tmp/sda
  - flash firmware to router internal storage by typing:
    sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar
  - device will reboot and after it gets up you will have edgerouter 4 running openwrt

Reviewed-by: Johannes Kimmel <fff@bareminimum.eu>
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>

diff --git a/target/linux/octeon/base-files/etc/board.d/01_network b/target/linux/octeon/base-files/etc/board.d/01_network
index c1b614f601f06afed43ad64e6afef5de3b9f13fd..749d99be1d11802fbc442a11b1d3312b806ea9fb 100755 (executable)
--- a/target/linux/octeon/base-files/etc/board.d/01_network
+++ b/target/linux/octeon/base-files/etc/board.d/01_network
@@ -11,6 +11,9 @@ case "$(board_name)" in
 itus,shield-router)
        ucidef_set_interfaces_lan_wan "eth1 eth2" "eth0"
        ;;
+ubnt,edgerouter-4)
+       ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "lan0"
+       ;;
 *)
        ucidef_set_interfaces_lan_wan "eth0" "eth1"
        ;;

diff --git a/target/linux/octeon/base-files/lib/preinit/01_sysinfo b/target/linux/octeon/base-files/lib/preinit/01_sysinfo
index 34fa7392d2267984901f3180b3906f1cbcc9d8d7..d66618b0cfdaaffc5f410e55cf53f22a2efa797f 100644 (file)
--- a/target/linux/octeon/base-files/lib/preinit/01_sysinfo
+++ b/target/linux/octeon/base-files/lib/preinit/01_sysinfo
@@ -17,6 +17,11 @@ do_sysinfo_octeon() {
                name="erpro"
                ;;
 
+       "UBNT_E300"*)
+               # let generic 02_sysinfo handle it since device has its own device tree
+               return 0
+               ;;
+
        "ITUS_SHIELD"*)
                name="itus,shield-router"
                ;;

diff --git a/target/linux/octeon/base-files/lib/preinit/79_move_config b/target/linux/octeon/base-files/lib/preinit/79_move_config
index 086f7c62e2573fe5f427803025f249e0848ace22..5a84e6f18a68ae50b51375a719e29fe272e31133 100644 (file)
--- a/target/linux/octeon/base-files/lib/preinit/79_move_config
+++ b/target/linux/octeon/base-files/lib/preinit/79_move_config
@@ -21,6 +21,9 @@ octeon_move_config() {
                itus,shield-router)
                        move_config "/dev/mmcblk1p1"
                        ;;
+               ubnt,edgerouter-4)
+                       move_config "/dev/mmcblk0p1"
+                       ;;
        esac
 }
 

diff --git a/target/linux/octeon/base-files/lib/upgrade/platform.sh b/target/linux/octeon/base-files/lib/upgrade/platform.sh
index 33a99312637740b0f9381510915f579df8da307d..ad5baef4a19fd95a747f5739abdf93c6d4bd1681 100755 (executable)
--- a/target/linux/octeon/base-files/lib/upgrade/platform.sh
+++ b/target/linux/octeon/base-files/lib/upgrade/platform.sh
@@ -29,6 +29,11 @@ platform_copy_config() {
                cp -af "$UPGRADE_BACKUP" "/mnt/$BACKUP_FILE"
                umount /mnt
                ;;
+       ubnt,edgerouter-4)
+               mount -t vfat /dev/mmcblk0p1 /mnt
+               cp -af "$UPGRADE_BACKUP" "/mnt/$BACKUP_FILE"
+               umount /mnt
+               ;;
        esac
 }
 
@@ -78,7 +83,8 @@ platform_do_upgrade() {
 
        [ -b "${rootfs}" ] || return 1
        case "$board" in
-       er)
+       er | \
+       ubnt,edgerouter-4)
                kernel=mmcblk0p1
                ;;
        erlite)
@@ -107,7 +113,8 @@ platform_check_image() {
        case "$board" in
        er | \
        erlite | \
-       itus,shield-router)
+       itus,shield-router | \
+       ubnt,edgerouter-4)
                local kernel_length=$(tar xf $tar_file $board_dir/kernel -O | wc -c 2> /dev/null)
                local rootfs_length=$(tar xf $tar_file $board_dir/root -O | wc -c 2> /dev/null)
                [ "$kernel_length" = 0 -o "$rootfs_length" = 0 ] && {

diff --git a/target/linux/octeon/config-5.4 b/target/linux/octeon/config-5.4
index 1b0f9f216eff2e1df35f90e1e33e39237e400c4c..c2012372ec0e1ca079e094dfc8a71fc874070bdf 100644 (file)
--- a/target/linux/octeon/config-5.4
+++ b/target/linux/octeon/config-5.4
@@ -25,7 +25,7 @@ CONFIG_BLK_MQ_PCI=y
 CONFIG_BLK_SCSI_REQUEST=y
 CONFIG_BUILTIN_DTB=y
 # CONFIG_CAVIUM_CN63XXP1 is not set
-CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE=2
+CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE=0
 CONFIG_CAVIUM_OCTEON_LOCK_L2=y
 CONFIG_CAVIUM_OCTEON_LOCK_L2_EXCEPTION=y
 CONFIG_CAVIUM_OCTEON_LOCK_L2_INTERRUPT=y
@@ -68,7 +68,14 @@ CONFIG_CRYPTO_RNG2=y
 CONFIG_DNOTIFY=y
 CONFIG_DTC=y
 CONFIG_EARLY_PRINTK=y
+CONFIG_EDAC=y
 CONFIG_EDAC_ATOMIC_SCRUB=y
+# CONFIG_EDAC_DEBUG is not set
+CONFIG_EDAC_LEGACY_SYSFS=y
+CONFIG_EDAC_OCTEON_PC=y
+CONFIG_EDAC_OCTEON_L2C=y
+CONFIG_EDAC_OCTEON_LMC=y
+CONFIG_EDAC_OCTEON_PCI=y
 CONFIG_EDAC_SUPPORT=y
 CONFIG_EFI_EARLYCON=y
 CONFIG_ENABLE_MUST_CHECK=y
@@ -150,6 +157,8 @@ CONFIG_HZ=250
 CONFIG_HZ_250=y
 CONFIG_HZ_PERIODIC=y
 CONFIG_IMAGE_CMDLINE_HACK=y
+CONFIG_I2C=y
+CONFIG_I2C_OCTEON=y
 CONFIG_INITRAMFS_SOURCE=""
 CONFIG_IRQCHIP=y
 CONFIG_IRQ_DOMAIN=y
@@ -173,14 +182,14 @@ CONFIG_MIPS_ASID_SHIFT=0
 CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER=y
 # CONFIG_MIPS_CMDLINE_FROM_DTB is not set
 CONFIG_MIPS_EBPF_JIT=y
-# CONFIG_MIPS_ELF_APPENDED_DTB is not set
+CONFIG_MIPS_ELF_APPENDED_DTB=y
 CONFIG_MIPS_L1_CACHE_SHIFT=7
 CONFIG_MIPS_L1_CACHE_SHIFT_7=y
 # CONFIG_MIPS_NO_APPENDED_DTB is not set
 CONFIG_MIPS_NR_CPU_NR_MAP=1024
 CONFIG_MIPS_NR_CPU_NR_MAP_1024=y
 CONFIG_MIPS_PGD_C0_CONTEXT=y
-CONFIG_MIPS_RAW_APPENDED_DTB=y
+# CONFIG_MIPS_RAW_APPENDED_DTB is not set
 CONFIG_MIPS_SPRAM=y
 # CONFIG_MIPS_VA_BITS_48 is not set
 CONFIG_MMC=y
@@ -192,7 +201,10 @@ CONFIG_MODULES_USE_ELF_RELA=y
 # CONFIG_MTD_CFI_INTELEXT is not set
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_SPI_NOR_USE_4K_SECTORS=y
 CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NET_DSA=y
 CONFIG_NET_FLOW_LIMIT=y
 CONFIG_NLS=y
 CONFIG_NLS_CODEPAGE_437=y
@@ -202,7 +214,7 @@ CONFIG_NR_CPUS=16
 CONFIG_NR_CPUS_DEFAULT_64=y
 CONFIG_NVMEM=y
 CONFIG_OCTEON_ETHERNET=y
-# CONFIG_OCTEON_ILM is not set
+CONFIG_OCTEON_ILM=y
 CONFIG_OCTEON_MGMT_ETHERNET=y
 CONFIG_OCTEON_USB=y
 CONFIG_OCTEON_WDT=y
@@ -220,6 +232,8 @@ CONFIG_PADATA=y
 CONFIG_PCI=y
 CONFIG_PCI_DOMAINS=y
 CONFIG_PCI_DRIVERS_LEGACY=y
+CONFIG_PCIEAER=y
+CONFIG_PCIEPORTBUS=y
 CONFIG_PERF_USE_VMALLOC=y
 CONFIG_PGTABLE_LEVELS=3
 CONFIG_PHYLIB=y
@@ -243,6 +257,9 @@ CONFIG_SG_POOL=y
 CONFIG_SMP=y
 CONFIG_SPARSEMEM=y
 CONFIG_SPARSEMEM_STATIC=y
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_OCTEON=y
 CONFIG_SRCU=y
 CONFIG_SWIOTLB=y
 CONFIG_SWPHY=y
@@ -275,6 +292,7 @@ CONFIG_USB_STORAGE=y
 CONFIG_USB_SUPPORT=y
 CONFIG_USE_OF=y
 CONFIG_VFAT_FS=y
+CONFIG_VITESSE_PHY=y
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_WATCHDOG_CORE=y
 CONFIG_WEAK_ORDERING=y

diff --git a/target/linux/octeon/files/arch/mips/boot/dts/cavium-octeon/cn7130_ubnt_edgerouter-4.dts b/target/linux/octeon/files/arch/mips/boot/dts/cavium-octeon/cn7130_ubnt_edgerouter-4.dts
new file mode 100644 (file)
index 0000000..a89455c
--- /dev/null
+++ b/target/linux/octeon/files/arch/mips/boot/dts/cavium-octeon/cn7130_ubnt_edgerouter-4.dts
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "cn71xx.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "ubnt,edgerouter-4", "cavium,cn7130";
+       model = "Ubiquiti EdgeRouter 4";
+
+       aliases {
+               /* White + Blinking Blue */
+               led-boot = &led_power_white;
+               /* Blue + Blinking White */
+               led-failsafe = &led_power_blue;
+               /* Constant Blue */
+               led-running = &led_power_blue;
+               /* Blue + Blinking White */
+               led-upgrade = &led_power_blue;
+       };
+
+       memory@0 {
+               device_type = "memory";
+               reg = <0x0 0x00000000>,
+                     <0x0 0x10000000>,
+                     <0x0 0x20000000>,
+                     <0x0 0x30000000>;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_power_blue: power_blue {
+                       label = "blue:power";
+                       gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+               };
+
+               led_power_white: power_white {
+                       label = "white:power";
+                       gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys-polled";
+               poll-interval = <20>;
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+       };
+
+       sfp: sfp {
+               compatible = "sff,sfp";
+               i2c-bus = <&twsi0>;
+               /* Pins 12, 13 and 14 gets pulled low when SFP is plugged in */
+               mod-def0-gpio = <&gpio 12 GPIO_ACTIVE_LOW>;
+       };
+};
+
+&uart0 {
+       status = "okay";
+};
+
+&usb0 {
+       status = "okay";
+};
+
+&xhci0 {
+       status = "okay";
+       dr_mode = "host";
+};
+
+&twsi0 {
+       status = "okay";
+
+       sfp_eeprom@50 {
+               compatible = "at,24c04";
+               reg = <0x50>;
+       };
+
+       sfp_eeprom@51 {
+               compatible = "at,24c04";
+               reg = <0x51>;
+       };
+};
+
+&spi {
+       status = "okay";
+
+       flash@0 {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               compatible = "Macronix,mx25l6405d", "spi-flash";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partition@0 {
+                       label = "boot0";
+                       read-only;
+                       reg = <0x000000 0x300000>;
+               };
+
+               partition@300000 {
+                       label = "dummy";
+                       read-only;
+                       reg = <0x300000 0x100000>;
+               };
+
+               eeprom: partition@400000 {
+                       label = "eeprom";
+                       read-only;
+                       reg = <0x400000 0x10000>;
+               };
+       };
+};
+
+&mmc {
+       status = "okay";
+
+       mmc-slot@0 {
+               compatible = "mmc-slot";
+               reg = <0>;
+               non-removable;
+               max-frequency = <26000000>;
+               voltage-ranges = <3300 3300>;
+               bus-width = <8>;
+       };
+};
+
+&smi0 {
+       status = "okay";
+
+       phy4: ethernet-phy@4 {
+               device_type = "ethernet-phy";
+               interrupts = <17 8>;
+               interrupt-parent = <&gpio>;
+               compatible = "vitesse,vsc8504", "ethernet-phy-ieee802.3-c22";
+               reg = <4>;
+               sfp = <&sfp>;
+       };
+
+       phy5: ethernet-phy@5 {
+               device_type = "ethernet-phy";
+               interrupts = <17 8>;
+               interrupt-parent = <&gpio>;
+               compatible = "vitesse,vsc8504", "ethernet-phy-ieee802.3-c22";
+               reg = <5>;
+       };
+
+       phy6: ethernet-phy@6 {
+               device_type = "ethernet-phy";
+               interrupts = <17 8>;
+               interrupt-parent = <&gpio>;
+               compatible = "vitesse,vsc8504", "ethernet-phy-ieee802.3-c22";
+               reg = <6>;
+       };
+
+       phy7: ethernet-phy@7 {
+               device_type = "ethernet-phy";
+               interrupts = <17 8>;
+               interrupt-parent = <&gpio>;
+               compatible = "vitesse,vsc8504", "ethernet-phy-ieee802.3-c22";
+               reg = <7>;
+       };
+};
+
+&pip {
+       status = "okay";
+
+       interface@0 {
+               status = "okay";
+
+               ethernet@0 {
+                       label = "lan3";
+                       status = "okay";
+                       phy-mode = "sgmii";
+                       phy-handle = <&phy4>;
+                       mtd-mac-address = <&eeprom 0>;
+               };
+
+               ethernet@1 {
+                       label = "lan0";
+                       status = "okay";
+                       phy-mode = "sgmii";
+                       phy-handle = <&phy5>;
+                       mtd-mac-address = <&eeprom 0>;
+                       mtd-mac-address-increment = <(1)>;
+               };
+
+               ethernet@2 {
+                       label = "lan1";
+                       status = "okay";
+                       phy-mode = "sgmii";
+                       phy-handle = <&phy6>;
+                       mtd-mac-address = <&eeprom 0>;
+                       mtd-mac-address-increment = <(2)>;
+               };
+
+               ethernet@3 {
+                       label = "lan2";
+                       status = "okay";
+                       phy-mode = "sgmii";
+                       phy-handle = <&phy7>;
+                       mtd-mac-address = <&eeprom 0>;
+                       mtd-mac-address-increment = <(3)>;
+               };
+       };
+};

diff --git a/target/linux/octeon/files/arch/mips/boot/dts/cavium-octeon/cn71xx.dtsi b/target/linux/octeon/files/arch/mips/boot/dts/cavium-octeon/cn71xx.dtsi
new file mode 100644 (file)
index 0000000..4b6d1e2
--- /dev/null
+++ b/target/linux/octeon/files/arch/mips/boot/dts/cavium-octeon/cn71xx.dtsi
@@ -0,0 +1,357 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+/ {
+       compatible = "cavium,cn71xx";
+       #address-cells = <2>;
+       #size-cells = <2>;
+       interrupt-parent = <&ciu>;
+
+       soc {
+               #address-cells = <2>;
+               #size-cells = <2>;
+               compatible = "simple-bus";
+               ranges;
+
+               bootbus@1180000000000 {
+                       #address-cells = <2>;
+                       #size-cells = <1>;
+                       compatible = "cavium,octeon-3860-bootbus";
+                       reg = <0x11800 0x00 0x00 0x200>;
+                       ranges = <0x00 0x00 0x10000 0x10000000 0x00>,
+                                <0x01 0x00 0x10000 0x20000000 0x00>,
+                                <0x02 0x00 0x10000 0x30000000 0x00>,
+                                <0x03 0x00 0x10000 0x40000000 0x00>,
+                                <0x04 0x00 0x10000 0x50000000 0x00>,
+                                <0x05 0x00 0x10000 0x60000000 0x00>,
+                                <0x06 0x00 0x10000 0x70000000 0x00>,
+                                <0x07 0x00 0x10000 0x80000000 0x00>;
+               };
+
+               dma0: dma-engine@1180000000100 {
+                       status = "disabled";
+                       compatible = "cavium,octeon-5750-bootbus-dma";
+                       reg = <0x11800 0x100 0x0 0x08>;
+                       interrupts = <0 63>;
+               };
+
+               dma1: dma-engine@1180000000108 {
+                       status = "disabled";
+                       compatible = "cavium,octeon-5750-bootbus-dma";
+                       reg = <0x11800 0x108 0x0 0x08>;
+                       interrupts = <0 63>;
+               };
+
+               ciu: interrupt-controller@1070000000000 {
+                       #interrupt-cells = <2>;
+                       compatible = "cavium,octeon-3860-ciu";
+                       reg = <0x10700 0x00000000 0x0 0x7000>;
+                       interrupt-controller;
+               };
+
+               cib0: interrupt-controller@107000000e000 {
+                       #interrupt-cells = <2>;
+                       compatible = "cavium,octeon-7130-cib";
+                       reg = <0x10700 0xe000 0x0 0x08>, /* RAW */
+                             <0x10700 0xe100 0x0 0x08>; /* EN */
+                       cavium,max-bits = <23>;
+                       interrupts = <1 24>;
+                       interrupt-parent = <&ciu>;
+                       interrupt-controller;
+               };
+
+               cib1: interrupt-controller@107000000e200 {
+                       #interrupt-cells = <2>;
+                       compatible = "cavium,octeon-7130-cib";
+                       reg = <0x10700 0xe200 0x0 0x08>, /* RAW */
+                             <0x10700 0xe300 0x0 0x08>; /* EN */
+                       cavium,max-bits = <12>;
+                       interrupts = <1 52>;
+                       interrupt-parent = <&ciu>;
+                       interrupt-controller;
+               };
+
+               cib2: interrupt-controller@107000000e400 {
+                       #interrupt-cells = <2>;
+                       compatible = "cavium,octeon-7130-cib";
+                       reg = <0x10700 0xe400 0x0 0x08>, /* RAW */
+                             <0x10700 0xe500 0x0 0x08>; /* EN */
+                       cavium,max-bits = <6>;
+                       interrupts = <1 63>;
+                       interrupt-parent = <&ciu>;
+                       interrupt-controller;
+               };
+
+               cib3: interrupt-controller@107000000e600 {
+                       #interrupt-cells = <2>;
+                       compatible = "cavium,octeon-7130-cib";
+                       reg = <0x10700 0xe600 0x0 0x08>, /* RAW */
+                             <0x10700 0xe700 0x0 0x08>; /* EN */
+                       cavium,max-bits = <4>;
+                       interrupts = <2 16>;
+                       interrupt-parent = <&ciu>;
+                       interrupt-controller;
+               };
+
+               cib4: interrupt-controller@107000000e800 {
+                       #interrupt-cells = <2>;
+                       compatible = "cavium,octeon-7130-cib";
+                       reg = <0x10700 0xe800 0x0 0x08>, /* RAW */
+                             <0x10700 0xea00 0x0 0x08>; /* EN */
+                       cavium,max-bits = <11>;
+                       interrupts = <1 33>;
+                       interrupt-parent = <&ciu>;
+                       interrupt-controller;
+               };
+
+               cib5: interrupt-controller@107000000e900 {
+                       #interrupt-cells = <2>;
+                       compatible = "cavium,octeon-7130-cib";
+                       reg = <0x10700 0xe900 0x00 0x08>, /* RAW */
+                             <0x10700 0xeb00 0x00 0x08>; /* EN */
+                       cavium,max-bits = <11>;
+                       interrupts = <1 23>;
+                       interrupt-parent = <&ciu>;
+                       interrupt-controller;
+               };
+
+               cib6: interrupt-controller@107000000ec00 {
+                       #interrupt-cells = <2>;
+                       compatible = "cavium,octeon-7130-cib";
+                       reg = <0x10700 0xec00 0x0 0x08>, /* RAW */
+                             <0x10700 0xee00 0x0 0x08>; /* EN */
+                       cavium,max-bits = <15>;
+                       interrupts = <2 17>;
+                       interrupt-parent = <&ciu>;
+                       interrupt-controller;
+               };
+
+               gpio: gpio-controller@1070000000800 {
+                       #interrupt-cells = <2>;
+                       #gpio-cells = <2>;
+                       compatible = "cavium,octeon-3860-gpio";
+                       reg = <0x10700 0x800 0x0 0x100>;
+                       interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+                                    <0 20>, <0 21>, <0 22>, <0 23>,
+                                    <0 24>, <0 25>, <0 26>, <0 27>,
+                                    <0 28>, <0 29>, <0 30>, <0 31>;
+                       interrupt-controller;
+                       gpio-controller;
+               };
+
+               mmc: mmc@1180000002000 {
+                       status = "disabled";
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       compatible = "cavium,octeon-6130-mmc";
+                       reg = <0x11800 0x2000 0x0 0x100>,
+                             <0x11800 0x168 0x0 0x20>;
+                       interrupts = <1 19>, <0 63>;
+               };
+
+               smi0: mdio@1180000001800 {
+                       status = "disabled";
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       compatible = "cavium,octeon-3860-mdio";
+                       reg = <0x11800 0x1800 0x0 0x40>;
+               };
+
+               smi1: mdio@1180000001900 {
+                       status = "disabled";
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       compatible = "cavium,octeon-3860-mdio";
+                       reg = <0x11800 0x1900 0x0 0x40>;
+               };
+
+               pip: pip@11800a0000000 {
+                       status = "disabled";
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       compatible = "cavium,octeon-3860-pip";
+                       reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+                       interface@0 {
+                               status = "disabled";
+                               #address-cells = <1>;
+                               #size-cells = <0>;
+                               compatible = "cavium,octeon-3860-pip-interface";
+                               reg = <0>; /* Interface */
+
+                               ethernet@0 {
+                                       status = "disabled";
+                                       compatible = "cavium,octeon-3860-pip-port";
+                                       reg = <0>; /* Port */
+                               };
+
+                               ethernet@1 {
+                                       status = "disabled";
+                                       compatible = "cavium,octeon-3860-pip-port";
+                                       reg = <1>; /* Port */
+                               };
+
+                               ethernet@2 {
+                                       status = "disabled";
+                                       compatible = "cavium,octeon-3860-pip-port";
+                                       reg = <2>; /* Port */
+                               };
+
+                               ethernet@3 {
+                                       status = "disabled";
+                                       compatible = "cavium,octeon-3860-pip-port";
+                                       reg = <3>; /* Port */
+                               };
+                       };
+
+                       interface@1 {
+                               status = "disabled";
+                               #address-cells = <1>;
+                               #size-cells = <0>;
+                               compatible = "cavium,octeon-3860-pip-interface";
+                               reg = <1>; /* Interface */
+
+                               ethernet@0 {
+                                       status = "disabled";
+                                       compatible = "cavium,octeon-3860-pip-port";
+                                       reg = <0>; /* Port */
+                               };
+
+                               ethernet@1 {
+                                       status = "disabled";
+                                       compatible = "cavium,octeon-3860-pip-port";
+                                       reg = <1>; /* Port */
+                               };
+
+                               ethernet@2 {
+                                       status = "disabled";
+                                       compatible = "cavium,octeon-3860-pip-port";
+                                       reg = <2>; /* Port */
+                               };
+
+                               ethernet@3 {
+                                       status = "disabled";
+                                       compatible = "cavium,octeon-3860-pip-port";
+                                       reg = <3>; /* Port */
+                               };
+                       };
+               };
+
+               twsi0: i2c@1180000001000 {
+                       status = "disabled";
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       compatible = "cavium,octeon-3860-twsi";
+                       reg = <0x11800 0x1000 0x0 0x200>;
+                       interrupts = <0 45>;
+                       clock-frequency = <100000>;
+               };
+
+               twsi1: i2c@1180000001200 {
+                       status = "disabled";
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       compatible = "cavium,octeon-3860-twsi";
+                       reg = <0x11800 0x1200 0x0 0x200>;
+                       interrupts = <0 59>;
+                       clock-frequency = <100000>;
+               };
+
+               uctl@118006c000000 {
+                       status = "disabled";
+                       #address-cells = <2>;
+                       #size-cells = <2>;
+                       compatible = "cavium,octeon-7130-sata-uctl";
+                       reg = <0x11800 0x6c000000 0x00 0x100>;
+                       ranges;
+
+                       sata@16c0000000000 {
+                               status = "disabled";
+                               compatible = "cavium,octeon-7130-ahci";
+                               reg = <0x16c00 0x00 0x00 0x200>;
+                               interrupt-parent = <&cib3>;
+                               interrupts = <2 4>;
+                       };
+               };
+
+               usb0: uctl@1180068000000 {
+                       status = "disabled";
+                       #address-cells = <2>;
+                       #size-cells = <2>;
+                       compatible = "cavium,octeon-7130-usb-uctl";
+                       reg = <0x11800 0x68000000 0x00 0x100>;
+                       ranges;
+                       power = <0x02 0x01 0x00>;
+                       refclk-frequency = <100000000>;
+                       refclk-type-hs = "pll_ref_clk";
+                       refclk-type-ss = "dlmc_ref_clk1";
+
+                       xhci0: xhci@1680000000000 {
+                               status = "disabled";
+                               compatible = "cavium,octeon-7130-xhci", "synopsys,dwc3";
+                               reg = <0x16800 0x0 0x10 0x00>;
+                               interrupts = <9 4>;
+                               interrupt-parent = <&cib4>;
+                       };
+               };
+
+               usb1: uctl@1180069000000 {
+                       status = "disabled";
+                       #address-cells = <2>;
+                       #size-cells = <2>;
+                       compatible = "cavium,octeon-7130-usb-uctl";
+                       reg = <0x11800 0x69000000 0x00 0x100>;
+                       ranges;
+                       power = <0x02 0x02 0x01>;
+                       refclk-frequency = <100000000>;
+                       refclk-type-hs = "pll_ref_clk";
+                       refclk-type-ss = "dlmc_ref_clk1";
+
+                       xhci1: xhci@1690000000000 {
+                               status = "disabled";
+                               compatible = "cavium,octeon-7130-xhci", "synopsys,dwc3";
+                               reg = <0x16900 0x0 0x10 0x00>;
+                               interrupts = <9 4>;
+                               interrupt-parent = <&cib5>;
+                       };
+               };
+
+               uart0: serial@1180000000800 {
+                       status = "disabled";
+                       compatible = "cavium,octeon-3860-uart", "ns16550";
+                       reg = <0x11800 0x800 0x0 0x400>;
+                       reg-shift = <3>;
+                       interrupts = <0 34>;
+                       clock-frequency = <400000000>;
+                       current-speed = <115200>;
+               };
+
+               uart1: serial@1180000000c00 {
+                       status = "disabled";
+                       compatible = "cavium,octeon-3860-uart", "ns16550";
+                       reg = <0x11800 0xc00 0x0 0x400>;
+                       reg-shift = <3>;
+                       interrupts = <0 35>;
+                       clock-frequency = <400000000>;
+                       current-speed = <115200>;
+               };
+
+               ocla0@11800a8000000 {
+                       status = "disabled";
+                       compatible = "cavium,octeon-7130-ocla";
+                       reg = <0x11800 0xa8000000 0x0 0x500000>;
+                       interrupts = <0x08 0x01 0x09 0x01 0x0b 0x01>;
+                       interrupt-parent = <&cib6>;
+               };
+
+               spi: spi@1070000001000 {
+                       status = "disabled";
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       compatible = "cavium,octeon-3010-spi";
+                       reg = <0x10700 0x1000 0x00 0x100>;
+                       interrupts = <0 58>;
+                       spi-max-frequency = <100000000>;
+               };
+       };
+};

diff --git a/target/linux/octeon/image/Makefile b/target/linux/octeon/image/Makefile
index 7851e4a99c203a7b7aaf18416e8add028bdd83be..b91c262447c9db60da1c1321e9223b96769f4ba2 100644 (file)
--- a/target/linux/octeon/image/Makefile
+++ b/target/linux/octeon/image/Makefile
@@ -7,11 +7,17 @@
 include $(TOPDIR)/rules.mk
 include $(INCLUDE_DIR)/image.mk
 
+define Build/append-dtb-to-elf
+       $(TARGET_CROSS)objcopy --update-section .appended_dtb=$(KDIR)/image-$(DEVICE_DTS).dtb $@
+endef
+
 define Build/strip-kernel
        # Workaround pre-SDK-1.9.0 u-boot versions not handling the .notes section
        $(TARGET_CROSS)strip -R .notes $@ -o $@.stripped && mv $@.stripped $@
 endef
 
+DTS_DIR := $(DTS_DIR)/cavium-octeon
+
 define Device/Default
   PROFILES = Default $$(DEVICE_NAME)
   KERNEL_NAME := vmlinux.elf
@@ -48,6 +54,17 @@ define Device/ubnt_edgerouter
 endef
 TARGET_DEVICES += ubnt_edgerouter
 
+define Device/ubnt_edgerouter-4
+  DEVICE_VENDOR := Ubiquiti
+  DEVICE_MODEL := EdgeRouter 4
+  DEVICE_DTS := cn7130_ubnt_edgerouter-4
+  DEVICE_PACKAGES += kmod-gpio-button-hotplug kmod-leds-gpio kmod-of-mdio kmod-sfp kmod-usb3 kmod-usb-dwc3 kmod-usb-storage-uas
+  KERNEL := kernel-bin | patch-cmdline | append-dtb-to-elf
+  KERNEL_DEPENDS := $$(wildcard $(DTS_DIR)/$(DEVICE_DTS).dts)
+  CMDLINE := root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait
+endef
+TARGET_DEVICES += ubnt_edgerouter-4
+
 ERLITE_CMDLINE:=-mtdparts=phys_mapped_flash:512k(boot0)ro,512k(boot1)ro,64k(eeprom)ro root=/dev/sda2 rootfstype=squashfs,ext4 rootwait
 define Device/ubnt_edgerouter-lite
   DEVICE_VENDOR := Ubiquiti

diff --git a/target/linux/octeon/patches-5.4/140-octeon_e300_support.patch b/target/linux/octeon/patches-5.4/140-octeon_e300_support.patch
new file mode 100644 (file)
index 0000000..36b5d6a
--- /dev/null
+++ b/target/linux/octeon/patches-5.4/140-octeon_e300_support.patch
@@ -0,0 +1,18 @@
+--- a/arch/mips/include/asm/octeon/cvmx-bootinfo.h
++++ b/arch/mips/include/asm/octeon/cvmx-bootinfo.h
+@@ -296,6 +296,7 @@
+       CVMX_BOARD_TYPE_CUST_PRIVATE_MIN = 20001,
+       CVMX_BOARD_TYPE_UBNT_E100 = 20002,
+       CVMX_BOARD_TYPE_ITUS_SHIELD = 20006,
++      CVMX_BOARD_TYPE_UBNT_E300 = 20300,
+       CVMX_BOARD_TYPE_KONTRON_S1901 = 21901,
+       CVMX_BOARD_TYPE_CUST_PRIVATE_MAX = 30000,
+ 
+@@ -397,6 +398,7 @@
+               ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_PRIVATE_MIN)
+               ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_UBNT_E100)
+               ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_ITUS_SHIELD)
++              ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_UBNT_E300)
+               ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_KONTRON_S1901)
+               ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_PRIVATE_MAX)
+       }