This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
bool "Support imx31_phycore"
select CPU_ARM1136
-config TARGET_QONG
- bool "Support qong"
- select CPU_ARM1136
-
config TARGET_MX31ADS
bool "Support mx31ads"
select CPU_ARM1136
source "board/compulab/cm_t335/Kconfig"
source "board/compulab/cm_t43/Kconfig"
source "board/creative/xfi3/Kconfig"
-source "board/davedenx/qong/Kconfig"
source "board/denx/m28evk/Kconfig"
source "board/denx/m53evk/Kconfig"
source "board/freescale/ls2085a/Kconfig"
+++ /dev/null
-if TARGET_QONG
-
-config SYS_BOARD
- default "qong"
-
-config SYS_VENDOR
- default "davedenx"
-
-config SYS_SOC
- default "mx31"
-
-config SYS_CONFIG_NAME
- default "qong"
-
-endif
+++ /dev/null
-QONG BOARD
-M: Wolfgang Denk <wd@denx.de>
-S: Maintained
-F: board/davedenx/qong/
-F: include/configs/qong.h
-F: configs/qong_defconfig
+++ /dev/null
-#
-# (C) Copyright 2009
-# Ilya Yanok, Emcraft Systems Ltd, <yanok@emcraft.com>
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := qong.o fpga.o
-obj-y += lowlevel_init.o
+++ /dev/null
-/*
- * (C) Copyright 2010
- * Stefano Babic, DENX Software Engineering, sbabic@denx.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/gpio.h>
-#include <fpga.h>
-#include <lattice.h>
-#include "qong_fpga.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_FPGA)
-
-static void qong_jtag_init(void)
-{
- return;
-}
-
-static void qong_fpga_jtag_set_tdi(int value)
-{
- gpio_set_value(QONG_FPGA_TDI_PIN, value);
-}
-
-static void qong_fpga_jtag_set_tms(int value)
-{
- gpio_set_value(QONG_FPGA_TMS_PIN, value);
-}
-
-static void qong_fpga_jtag_set_tck(int value)
-{
- gpio_set_value(QONG_FPGA_TCK_PIN, value);
-}
-
-static int qong_fpga_jtag_get_tdo(void)
-{
- return gpio_get_value(QONG_FPGA_TDO_PIN);
-}
-
-lattice_board_specific_func qong_fpga_fns = {
- qong_jtag_init,
- qong_fpga_jtag_set_tdi,
- qong_fpga_jtag_set_tms,
- qong_fpga_jtag_set_tck,
- qong_fpga_jtag_get_tdo
-};
-
-Lattice_desc qong_fpga[CONFIG_FPGA_COUNT] = {
- {
- Lattice_XP2,
- lattice_jtag_mode,
- 356519,
- (void *) &qong_fpga_fns,
- NULL,
- 0,
- "lfxp2_5e_ftbga256"
- },
-};
-
-int qong_fpga_init(void)
-{
- int i;
-
- fpga_init();
-
- for (i = 0; i < CONFIG_FPGA_COUNT; i++) {
- fpga_add(fpga_lattice, &qong_fpga[i]);
- }
- return 0;
-}
-
-#endif
+++ /dev/null
-/*
- * Copyright (C) 2009, Emcraft Systems, Ilya Yanok <yanok@emcraft.com>
- *
- * Based on board/freescale/mx31ads/lowlevel_init.S
- * by Guennadi Liakhovetski.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <asm/arch/imx-regs.h>
-
-.macro REG reg, val
- ldr r2, =\reg
- ldr r3, =\val
- str r3, [r2]
-.endm
-
-.macro REG8 reg, val
- ldr r2, =\reg
- ldr r3, =\val
- strb r3, [r2]
-.endm
-
-.macro DELAY loops
- ldr r2, =\loops
-1:
- subs r2, r2, #1
- nop
- bcs 1b
-.endm
-
-.macro SETUP_RAM cfg, ctl
- /* B8xxxxxx - NAND, 8xxxxxxx - CSD0 RAM */
- REG 0xB8001010, 0x00000004
- ldr r3, =\cfg
- ldr r2, =WEIM_ESDCFG0
- str r3, [r2]
- REG 0xB8001000, 0x92100000
- REG 0x80000f00, 0x12344321
- REG 0xB8001000, 0xa2100000
- REG 0x80000000, 0x12344321
- REG 0x80000000, 0x12344321
- REG 0xB8001000, 0xb2100000
- REG8 0x80000033, 0xda
- REG8 0x81000000, 0xff
- ldr r3, =\ctl
- ldr r2, =WEIM_ESDCTL0
- str r3, [r2]
- REG 0x80000000, 0xDEADBEEF
- REG 0xB8001010, 0x0000000c
-
-.endm
-/* RedBoot: To support 133MHz DDR */
-.macro init_drive_strength
- /*
- * Disable maximum drive strength SDRAM/DDR lines by clearing DSE1 bits
- * in SW_PAD_CTL registers
- */
-
- /* SDCLK */
- ldr r1, =IOMUXC_SW_PAD_CTL(0x2b)
- ldr r0, [r1, #0x6C]
- bic r0, r0, #(1 << 12)
- str r0, [r1, #0x6C]
-
- /* CAS */
- ldr r0, [r1, #0x70]
- bic r0, r0, #(1 << 22)
- str r0, [r1, #0x70]
-
- /* RAS */
- ldr r0, [r1, #0x74]
- bic r0, r0, #(1 << 2)
- str r0, [r1, #0x74]
-
- /* CS2 (CSD0) */
- ldr r0, [r1, #0x7C]
- bic r0, r0, #(1 << 22)
- str r0, [r1, #0x7C]
-
- /* DQM3 */
- ldr r0, [r1, #0x84]
- bic r0, r0, #(1 << 22)
- str r0, [r1, #0x84]
-
- /* DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC) */
- ldr r2, =22 /* (0x2E0 - 0x288) / 4 = 22 */
-pad_loop:
- ldr r0, [r1, #0x88]
- bic r0, r0, #(1 << 22)
- bic r0, r0, #(1 << 12)
- bic r0, r0, #(1 << 2)
- str r0, [r1, #0x88]
- add r1, r1, #4
- subs r2, r2, #0x1
- bne pad_loop
-.endm /* init_drive_strength */
-
-.globl lowlevel_init
-lowlevel_init:
-
- init_drive_strength
-
- /* Image Processing Unit: */
- /* Too early to switch display on? */
- /* Switch on Display Interface */
- REG IPU_CONF, IPU_CONF_DI_EN
- /* Clock Control Module: */
- REG CCM_CCMR, 0x074B0BF5 /* Use CKIH, MCU PLL off */
-
- DELAY 0x40000
-
- REG CCM_CCMR, 0x074B0BF5 | CCMR_MPE /* MCU PLL on */
- /* Switch to MCU PLL */
- REG CCM_CCMR, (0x074B0BF5 | CCMR_MPE) & ~CCMR_MDS
-
- /* 399-133-66.5 */
- ldr r0, =CCM_BASE
- ldr r1, =0xFF871650
- /* PDR0 */
- str r1, [r0, #0x4]
- ldr r1, MPCTL_PARAM_399
- /* MPCTL */
- str r1, [r0, #0x10]
-
- /* Set UPLL=240MHz, USB=60MHz */
- ldr r1, =0x49FCFE7F
- /* PDR1 */
- str r1, [r0, #0x8]
- ldr r1, UPCTL_PARAM_240
- /* UPCTL */
- str r1, [r0, #0x14]
- /* default CLKO to 1/8 of the ARM core */
- mov r1, #0x00000208
- /* COSR */
- str r1, [r0, #0x1c]
-
- /* Default: 1, 4, 12, 1 */
- REG CCM_SPCTL, PLL_PD(1) | PLL_MFD(4) | PLL_MFI(12) | PLL_MFN(1)
-
-check_ddr_module:
-/* Set stackpointer in internal RAM to call get_ram_size */
- ldr sp, =(IRAM_BASE_ADDR + IRAM_SIZE - 16)
- stmfd sp!, {r0-r11, ip, lr}
- mov ip, lr /* save link reg across call */
-
- ldr r0,=0x08000000
- SETUP_RAM ESDCFG0_256MB, ESDCTL0_256MB
- ldr r0,=0x80000000
- ldr r1,=0x10000000
- bl get_ram_size
- ldr r1,=0x10000000
- cmp r0,r1
- beq restore_regs
- SETUP_RAM ESDCFG0_128MB, ESDCTL0_128MB
- ldr r0,=0x80000000
- ldr r1,=0x08000000
- bl get_ram_size
- ldr r1,=0x08000000
- cmp r0,r1
- beq restore_regs
-
-restore_regs:
- ldmfd sp!, {r0-r11, ip, lr}
- mov lr, ip /* restore link reg */
-
- mov pc, lr
-
-
-MPCTL_PARAM_399:
- .word (((1 - 1) << 26) + ((52 - 1) << 16) + (7 << 10) + (35 << 0))
-UPCTL_PARAM_240:
- .word (((2 - 1) << 26) + ((13 - 1) << 16) + (9 << 10) + (3 << 0))
-
- .equ ESDCFG0_128MB, \
- (0 << 21) + /* tXP */ \
- (1 << 20) + /* tWTR */ \
- (2 << 18) + /* tRP */ \
- (1 << 16) + /* tMRD */ \
- (0 << 15) + /* tWR */ \
- (5 << 12) + /* tRAS */ \
- (1 << 10) + /* tRRD */ \
- (3 << 8) + /* tCAS */ \
- (2 << 4) + /* tRCD */ \
- (0x0F << 0) /* tRC */
-
- .equ ESDCTL0_128MB, \
- (1 << 31) + /* enable */ \
- (0 << 28) + /* mode */ \
- (0 << 27) + /* supervisor protect */ \
- (2 << 24) + /* 13 rows */ \
- (2 << 20) + /* 10 cols */ \
- (2 << 16) + /* 32 bit */ \
- (3 << 13) + /* 7.81us (64ms/8192) */ \
- (0 << 10) + /* power down timer */ \
- (0 << 8) + /* full page */ \
- (1 << 7) + /* burst length */ \
- (0 << 0) /* precharge timer */
-
- .equ ESDCFG0_256MB, \
- (3 << 21) + /* tXP */ \
- (0 << 20) + /* tWTR */ \
- (2 << 18) + /* tRP */ \
- (1 << 16) + /* tMRD */ \
- (0 << 15) + /* tWR */ \
- (5 << 12) + /* tRAS */ \
- (1 << 10) + /* tRRD */ \
- (3 << 8) + /* tCAS */ \
- (2 << 4) + /* tRCD */ \
- (7 << 0) /* tRC */
-
- .equ ESDCTL0_256MB, \
- (1 << 31) + \
- (0 << 28) + \
- (0 << 27) + \
- (3 << 24) + /* 14 rows */ \
- (2 << 20) + /* 10 cols */ \
- (2 << 16) + \
- (4 << 13) + /* 3.91us (64ms/16384) */ \
- (0 << 10) + \
- (0 << 8) + \
- (1 << 7) + \
- (0 << 0)
+++ /dev/null
-/*
- *
- * (c) 2009 Emcraft Systems, Ilya Yanok <yanok@emcraft.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/io.h>
-#include <nand.h>
-#include <power/pmic.h>
-#include <fsl_pmic.h>
-#include <asm/gpio.h>
-#include "qong_fpga.h"
-#include <watchdog.h>
-#include <errno.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
- PHYS_SDRAM_1_SIZE);
- return 0;
-}
-
-static void qong_fpga_reset(void)
-{
- gpio_set_value(QONG_FPGA_RST_PIN, 0);
- udelay(30);
- gpio_set_value(QONG_FPGA_RST_PIN, 1);
-
- udelay(300);
-}
-
-int board_early_init_f(void)
-{
-#ifdef CONFIG_QONG_FPGA
- /* CS1: FPGA/Network Controller/GPIO, 16-bit, no DTACK */
- static const struct mxc_weimcs cs1 = {
- /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
- CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 0, 10, 0, 0, 1),
- /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
- CSCR_L(2, 0, 0, 4, 0, 0, 5, 0, 0, 0, 0, 1),
- /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
- CSCR_A(0, 4, 0, 2, 0, 0, 3, 0, 0, 0, 0, 0, 0, 0)
- };
-
- mxc_setup_weimcs(1, &cs1);
-
- /* setup pins for FPGA */
- mx31_gpio_mux(IOMUX_MODE(0x76, MUX_CTL_GPIO));
- mx31_gpio_mux(IOMUX_MODE(0x7e, MUX_CTL_GPIO));
- mx31_gpio_mux(IOMUX_MODE(0x91, MUX_CTL_OUT_FUNC | MUX_CTL_IN_GPIO));
- mx31_gpio_mux(IOMUX_MODE(0x92, MUX_CTL_GPIO));
- mx31_gpio_mux(IOMUX_MODE(0x93, MUX_CTL_GPIO));
-
- /* FPGA reset Pin */
- /* rstn = 0 */
- gpio_direction_output(QONG_FPGA_RST_PIN, 0);
-
- /* set interrupt pin as input */
- gpio_direction_input(QONG_FPGA_IRQ_PIN);
-
- /* FPGA JTAG Interface */
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SFS6, MUX_CTL_GPIO));
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SCK6, MUX_CTL_GPIO));
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_CAPTURE, MUX_CTL_GPIO));
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_COMPARE, MUX_CTL_GPIO));
- gpio_direction_output(QONG_FPGA_TCK_PIN, 0);
- gpio_direction_output(QONG_FPGA_TMS_PIN, 0);
- gpio_direction_output(QONG_FPGA_TDI_PIN, 0);
- gpio_direction_input(QONG_FPGA_TDO_PIN);
-#endif
-
- /* setup pins for UART1 */
- mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
- mx31_gpio_mux(MUX_TXD1__UART1_TXD_MUX);
- mx31_gpio_mux(MUX_RTS1__UART1_RTS_B);
- mx31_gpio_mux(MUX_CTS1__UART1_CTS_B);
-
- /* setup pins for SPI (pmic) */
- mx31_gpio_mux(MUX_CSPI2_SS0__CSPI2_SS0_B);
- mx31_gpio_mux(MUX_CSPI2_MOSI__CSPI2_MOSI);
- mx31_gpio_mux(MUX_CSPI2_MISO__CSPI2_MISO);
- mx31_gpio_mux(MUX_CSPI2_SCLK__CSPI2_CLK);
- mx31_gpio_mux(MUX_CSPI2_SPI_RDY__CSPI2_DATAREADY_B);
-
- /* Setup pins for USB2 Host */
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_CLK, MUX_CTL_FUNC));
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DIR, MUX_CTL_FUNC));
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_NXT, MUX_CTL_FUNC));
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_STP, MUX_CTL_FUNC));
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA0, MUX_CTL_FUNC));
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA1, MUX_CTL_FUNC));
-
-#define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
-
- mx31_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG);
- mx31_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG);
- mx31_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG);
- mx31_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG);
- mx31_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); /* USBH2_DATA0 */
- mx31_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); /* USBH2_DATA1 */
- mx31_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG); /* USBH2_DATA2 */
- mx31_set_pad(MX31_PIN_STXD6, H2_PAD_CFG); /* USBH2_DATA3 */
- mx31_set_pad(MX31_PIN_SFS3, H2_PAD_CFG); /* USBH2_DATA4 */
- mx31_set_pad(MX31_PIN_SCK3, H2_PAD_CFG); /* USBH2_DATA5 */
- mx31_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG); /* USBH2_DATA6 */
- mx31_set_pad(MX31_PIN_STXD3, H2_PAD_CFG); /* USBH2_DATA7 */
-
- mx31_set_gpr(MUX_PGP_UH2, 1);
-
- return 0;
-
-}
-
-int board_init(void)
-{
- /* Chip selects */
- /* CS0: Nor Flash #0 - it must be init'ed when executing from DDR */
- /* Assumptions: HCLK = 133 MHz, tACC = 130ns */
- static const struct mxc_weimcs cs0 = {
- /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
- CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 3, 21, 0, 0, 6),
- /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
- CSCR_L(0, 1, 3, 3, 1, 1, 5, 1, 0, 0, 0, 1),
- /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
- CSCR_A(0, 1, 2, 2, 0, 0, 2, 0, 0, 0, 0, 0, 0, 0)
- };
-
- mxc_setup_weimcs(0, &cs0);
-
- /* board id for linux */
- gd->bd->bi_arch_number = MACH_TYPE_QONG;
- gd->bd->bi_boot_params = (0x80000100); /* adress of boot parameters */
-
- qong_fpga_init();
-
- return 0;
-}
-
-int board_late_init(void)
-{
- u32 val;
- struct pmic *p;
- int ret;
-
- ret = pmic_init(I2C_PMIC);
- if (ret)
- return ret;
-
- p = pmic_get("FSL_PMIC");
- if (!p)
- return -ENODEV;
- /* Enable RTC battery */
- pmic_reg_read(p, REG_POWER_CTL0, &val);
- pmic_reg_write(p, REG_POWER_CTL0, val | COINCHEN);
- pmic_reg_write(p, REG_INT_STATUS1, RTCRSTI);
-
-#ifdef CONFIG_HW_WATCHDOG
- hw_watchdog_init();
-#endif
-
- return 0;
-}
-
-int checkboard(void)
-{
- printf("Board: DAVE/DENX Qong\n");
- return 0;
-}
-
-int misc_init_r(void)
-{
-#ifdef CONFIG_QONG_FPGA
- u32 tmp;
-
- tmp = *(volatile u32*)QONG_FPGA_CTRL_VERSION;
- printf("FPGA: ");
- printf("version register = %u.%u.%u\n",
- (tmp & 0xF000) >> 12, (tmp & 0x0F00) >> 8, tmp & 0x00FF);
-#endif
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
-#if defined(CONFIG_QONG_FPGA) && defined(CONFIG_DNET)
- return dnet_eth_initialize(0, (void *)CONFIG_DNET_BASE, -1);
-#else
- return 0;
-#endif
-}
-
-#if defined(CONFIG_QONG_FPGA) && defined(CONFIG_NAND_PLAT)
-static void board_nand_setup(void)
-{
- /* CS3: NAND 8-bit */
- static const struct mxc_weimcs cs3 = {
- /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
- CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 1, 15, 0, 0, 0),
- /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
- CSCR_L(2, 0, 0, 1, 3, 1, 3, 3, 0, 0, 0, 1),
- /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
- CSCR_A(0, 0, 0, 2, 0, 0, 2, 0, 0, 0, 0, 0, 0, 0)
- };
-
- mxc_setup_weimcs(3, &cs3);
-
- mx31_set_gpr(MUX_SDCTL_CSD1_SEL, 1);
-
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_WP, MUX_CTL_IN_GPIO));
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_CE, MUX_CTL_IN_GPIO));
- mx31_gpio_mux(IOMUX_MODE(MUX_CTL_NFC_RB, MUX_CTL_IN_GPIO));
-
- /* Make sure to reset the fpga else you cannot access NAND */
- qong_fpga_reset();
-
- /* Enable NAND flash */
- gpio_set_value(15, 1);
- gpio_set_value(14, 1);
- gpio_direction_output(15, 0);
- gpio_direction_input(16);
- gpio_direction_input(14);
-
-}
-
-int qong_nand_rdy(void *chip)
-{
- udelay(1);
- return gpio_get_value(16);
-}
-
-void qong_nand_select_chip(struct mtd_info *mtd, int chip)
-{
- if (chip >= 0)
- gpio_set_value(15, 0);
- else
- gpio_set_value(15, 1);
-
-}
-
-void qong_nand_plat_init(void *chip)
-{
- struct nand_chip *nand = (struct nand_chip *)chip;
- nand->chip_delay = 20;
- nand->select_chip = qong_nand_select_chip;
- nand->options &= ~NAND_BUSWIDTH_16;
- board_nand_setup();
-}
-
-#endif
+++ /dev/null
-/*
- *
- * (c) 2009 Emcraft Systems, Ilya Yanok <yanok@emcraft.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef QONG_FPGA_H
-#define QONG_FPGA_H
-
-#define QONG_FPGA_CTRL_BASE CONFIG_FPGA_BASE
-#define QONG_FPGA_CTRL_VERSION (QONG_FPGA_CTRL_BASE + 0x00000000)
-#define QONG_FPGA_PERIPH_SIZE (1 << 24)
-
-#define QONG_FPGA_TCK_PIN 26
-#define QONG_FPGA_TMS_PIN 25
-#define QONG_FPGA_TDI_PIN 8
-#define QONG_FPGA_TDO_PIN 7
-#define QONG_FPGA_RST_PIN 48
-#define QONG_FPGA_IRQ_PIN 40
-
-int qong_fpga_init(void);
-#endif /* QONG_FPGA_H */
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_TARGET_QONG=y
+++ /dev/null
-/*
- * Copyright (C) 2009, Ilya Yanok, Emcraft Systems, <yanok@emcraft.com>
- *
- * Configuration settings for the Dave/DENX QongEVB-LITE board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/imx-regs.h>
-
-/* High Level Configuration Options */
-#define CONFIG_MX31 /* This is a mx31 */
-#define CONFIG_QONG
-
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
-#define CONFIG_SYS_TEXT_BASE 0xa0000000
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1536 * 1024)
-
-/*
- * Hardware drivers
- */
-
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART1_BASE
-
-#define CONFIG_MXC_GPIO
-#define CONFIG_HW_WATCHDOG
-#define CONFIG_IMX_WATCHDOG
-
-#define CONFIG_MXC_SPI
-#define CONFIG_DEFAULT_SPI_BUS 1
-#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
-#define CONFIG_RTC_MC13XXX
-
-#define CONFIG_POWER
-#define CONFIG_POWER_SPI
-#define CONFIG_POWER_FSL
-#define CONFIG_FSL_PMIC_BUS 1
-#define CONFIG_FSL_PMIC_CS 0
-#define CONFIG_FSL_PMIC_CLK 100000
-#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
-#define CONFIG_FSL_PMIC_BITLEN 32
-
-/* FPGA */
-#define CONFIG_FPGA
-#define CONFIG_QONG_FPGA
-#define CONFIG_FPGA_BASE (CS1_BASE)
-#define CONFIG_FPGA_LATTICE
-#define CONFIG_FPGA_COUNT 1
-
-#ifdef CONFIG_QONG_FPGA
-/* Ethernet */
-#define CONFIG_DNET
-#define CONFIG_DNET_BASE (CS1_BASE + QONG_FPGA_PERIPH_SIZE)
-
-/* Framebuffer and LCD */
-#define CONFIG_VIDEO
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_MX3
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_CMD_BMP
-#define CONFIG_BMP_16BPP
-#define CONFIG_VIDEO_BMP_GZIP
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (512 << 10)
-
-/* USB */
-#define CONFIG_CMD_USB
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_MXC
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_MXC_USB_PORT 2
-#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT)
-#define CONFIG_MXC_USB_FLAGS MXC_EHCI_POWER_PINS_ENABLED
-#define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SUPPORT_VFAT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#endif /* CONFIG_CMD_USB */
-
-/*
- * Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
- * initial TFTP transfer, should the user wish one, significantly.
- */
-#define CONFIG_ARP_TIMEOUT 200UL
-
-#endif /* CONFIG_QONG_FPGA */
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/***********************************************************
- * Command definition
- ***********************************************************/
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_UNZIP
-
-#define CONFIG_BOARD_LATE_INIT
-
-#define CONFIG_BOOTDELAY 5
-
-#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs}" \
- " console=ttymxc0,${baudrate}\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "addmisc=setenv bootargs ${bootargs}\0" \
- "uboot_addr=A0000000\0" \
- "kernel_addr=A00C0000\0" \
- "ramdisk_addr=A0300000\0" \
- "u-boot=qong/u-boot.bin\0" \
- "kernel_addr_r=80800000\0" \
- "hostname=qong\0" \
- "bootfile=qong/uImage\0" \
- "rootpath=/opt/eldk-4.2-arm/armVFP\0" \
- "flash_self=run ramargs addip addtty addmtd addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
- "bootm ${kernel_addr}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
- "run nfsargs addip addtty addmtd addmisc;" \
- "bootm\0" \
- "bootcmd=run flash_self\0" \
- "load=tftp ${loadaddr} ${u-boot}\0" \
- "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
- " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
- " +${filesize};cp.b ${fileaddr} " \
- __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
- "upd=run load update\0" \
- "videomode=video=ctfb:x:640,y:480,depth:16,mode:0,pclk:40000," \
- "le:120,ri:40,up:35,lo:10,hs:30,vs:3,sync:100663296," \
- "vmode:0\0" \
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/* memtest works on first 255MB of RAM */
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
-#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0xff000000)
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
-
-#define CONFIG_MISC_INIT_R
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 CSD0_BASE
-#define PHYS_SDRAM_1_SIZE 0x10000000 /* 256 MB */
-
-/*
- * NAND driver
- */
-
-#ifndef __ASSEMBLY__
-extern void qong_nand_plat_init(void *chip);
-extern int qong_nand_rdy(void *chip);
-#endif
-#define CONFIG_NAND_PLAT
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CS3_BASE
-#define NAND_PLAT_INIT() qong_nand_plat_init(nand)
-
-#define QONG_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 24))
-#define QONG_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 23))
-#define QONG_NAND_WRITE(addr, cmd) \
- do { \
- __REG8(addr) = cmd; \
- } while (0)
-
-#define NAND_PLAT_WRITE_CMD(chip, cmd) QONG_NAND_WRITE(QONG_NAND_CLE(chip), cmd)
-#define NAND_PLAT_WRITE_ADR(chip, cmd) QONG_NAND_WRITE(QONG_NAND_ALE(chip), cmd)
-#define NAND_PLAT_DEV_READY(chip) (qong_nand_rdy(chip))
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE CS0_BASE
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-/* max number of sectors on one chip */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024
-/* Monitor at beginning of flash */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256KiB */
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x80000)
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* Flash memory is CFI compliant */
-#define CONFIG_SYS_FLASH_CFI
-/* Use drivers/cfi_flash.c */
-#define CONFIG_FLASH_CFI_DRIVER
-/* Use buffered writes (~10x faster) */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-/* Use hardware sector protection */
-#define CONFIG_SYS_FLASH_PROTECTION
-
-/*
- * Filesystem
- */
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_UBI
-#define CONFIG_CMD_UBIFS
-#define CONFIG_RBTREE
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_LZO
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=physmap-flash.0," \
- "nand0=gen_nand"
-#define MTDPARTS_DEFAULT \
- "mtdparts=physmap-flash.0:" \
- "512k(U-Boot),128k(env1),128k(env2)," \
- "2304k(kernel),13m(ramdisk),-(user);" \
- "gen_nand:" \
- "128m(nand)"
-
-/* additions for new relocation code, must be added to all boards */
-#define CONFIG_SYS_SDRAM_BASE 0x80000000
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)
-
-#define CONFIG_BOARD_EARLY_INIT_F
-
-#endif /* __CONFIG_H */
projects / project / bcm63xx / u-boot.git / commitdiff