ramips: add support for D-Link DIR-878 A1

Specifications:

    SoC: MT7621AT
    RAM: 128MB
    Flash: 16MB NOR SPI flash
    WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
    LAN: 5x1000M
    Firmware layout is Uboot with extra 96 bytes in header
    Base PCB is AP-MTKH7-0002
    LEDs Power Green,Power Orange,Internet Green,Internet Orange
    LEDs "2.4G" Green & "5G" Green connected directly to wifi module
    Buttons Reset,WPS,WIFI

Flashing instructions:

Upload image via emergency recovery mode
Push and hold reset button (on the back of the device) until power led
starts flashing (about 10 secs or so) while powering the device on.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device. Some browsers/OS combinations are known not to work, so if
you don't see the percentage complete displayed and moving within a few
seconds, restart the procedure from scratch and try anoher one,
or try the command line way.

Alternative method using command line on Linux:
curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1

Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
[use of generic uimage-padhdr in image generation code]
Signed-off-by: Petr Štetiar <ynezz@true.cz>

diff --git a/target/linux/ramips/dts/mt7621_dlink_dir-878-a1.dts b/target/linux/ramips/dts/mt7621_dlink_dir-878-a1.dts
new file mode 100644 (file)
index 0000000..15c46cb
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_dlink_dir-878-a1.dts
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "dlink,dir-878-a1", "mediatek,mt7621-soc";
+       model = "D-Link DIR-878 A1";
+
+       aliases {
+               led-boot = &led_power_orange;
+               led-failsafe = &led_power_green;
+               led-running = &led_power_green;
+               led-upgrade = &led_net_orange;
+               label-mac-device = &gmac0;
+       };
+
+       chosen {
+               bootargs = "console=ttyS0,57600";
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_power_orange: power_orange {
+                       label = "dir-878-a1:orange:power";
+                       gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+               };
+
+               led_power_green: power_green {
+                       label = "dir-878-a1:green:power";
+                       gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+               };
+
+               led_net_orange: net_orange {
+                       label = "dir-878-a1:orange:net";
+                       gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+               };
+
+               net_green {
+                       label = "dir-878-a1:green:net";
+                       gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+
+               wifi {
+                       label = "wifi";
+                       gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RFKILL>;
+               };
+       };
+};
+
+&spi0 {
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <50000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x0 0x30000>;
+                               read-only;
+                       };
+
+                       partition@30000 {
+                               label = "u-boot-env";
+                               reg = <0x30000 0x10000>;
+                               read-only;
+                       };
+
+                       factory: partition@40000 {
+                               label = "factory";
+                               reg = <0x40000 0x20000>;
+                               read-only;
+                       };
+
+                       partition@60000 {
+                               compatible = "sge,uimage";
+                               label = "firmware";
+                               reg = <0x60000 0xfa0000>;
+                       };
+               };
+       };
+};
+
+&pcie {
+       status = "okay";
+};
+
+&pcie0 {
+       wifi@0,0 {
+               compatible = "mediatek,mt76";
+               reg = <0x0000 0 0 0 0>;
+               mediatek,mtd-eeprom = <&factory 0x0000>;
+               ieee80211-freq-limit = <2400000 2500000>;
+
+               led {
+                       led-active-low;
+               };
+       };
+};
+
+&pcie1 {
+       wifi@0,0 {
+               compatible = "mediatek,mt76";
+               reg = <0x0000 0 0 0 0>;
+               mediatek,mtd-eeprom = <&factory 0x8000>;
+               ieee80211-freq-limit = <5000000 6000000>;
+
+               led {
+                       led-active-low;
+               };
+       };
+};
+
+&gmac0 {
+       mtd-mac-address = <&factory 0xe000>;
+};
+
+&switch0 {
+       ports {
+               port@0 {
+                       status = "okay";
+                       label = "lan4";
+               };
+
+               port@1 {
+                       status = "okay";
+                       label = "lan3";
+               };
+
+               port@2 {
+                       status = "okay";
+                       label = "lan2";
+               };
+
+               port@3 {
+                       status = "okay";
+                       label = "lan1";
+               };
+
+               port@4 {
+                       status = "okay";
+                       label = "wan";
+                       mtd-mac-address = <&factory 0xe006>;
+               };
+       };
+};
+
+&state_default {
+       gpio {
+               groups = "i2c", "uart3", "jtag", "wdt";
+               function = "gpio";
+       };
+};

diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 9e5bd811b01ccd2214ef292cf17ef380b28cd7d9..48561d5ff940fd1df1a53a10397218fbd9cc3bc3 100644 (file)
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -236,6 +236,21 @@ define Device/dlink_dir-860l-b1
 endef
 TARGET_DEVICES += dlink_dir-860l-b1
 
+define Device/dlink_dir-878-a1
+  IMAGE_SIZE := 16000k
+  DEVICE_VENDOR := D-Link
+  DEVICE_MODEL := DIR-878
+  DEVICE_VARIANT := A1
+  DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware wpad-basic
+  KERNEL_INITRAMFS := $$(KERNEL) | uimage-padhdr 96
+  IMAGES += factory.bin
+  IMAGE/sysupgrade.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\
+       pad-rootfs | append-metadata | check-size
+  IMAGE/factory.bin := append-kernel | append-rootfs | uimage-padhdr 96 |\
+       check-size
+endef
+TARGET_DEVICES += dlink_dir-878-a1
+
 define Device/d-team_newifi-d2
   $(Device/uimage-lzma-loader)
   IMAGE_SIZE := 32448k

diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
index a0f9b2b10dddc3dd493c5cce95373b490ecc707d..02f264fb4284b900c5ab1fd105d13f9bac70ac90 100755 (executable)
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
@@ -26,7 +26,8 @@ d-team,pbr-m1|\
 gehua,ghl-r-001)
        ucidef_set_led_netdev "internet" "internet" "$boardname:blue:internet" "wan"
        ;;
-dlink,dir-860l-b1)
+dlink,dir-860l-b1|\
+dlink,dir-878-a1)
        ucidef_set_led_netdev "wan" "wan" "$boardname:green:net" "wan"
        ;;
 gnubee,gb-pc1|\