This adds support for the Ubiquiti Bullet M (AR7240).
Specifications:
- AR7240 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!
Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other Ubiquiti M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_bullet-m-ar7240-squashfs-factory.bin
The "fixed-link" section of the device tree is needed to avoid errors like this:
Generic PHY mdio.0:1f:04: Master/Slave resolution failed, maybe conflicting manual settings?
With "fixed-link", the errors go away and eth0 comes up reliably.
Signed-off-by: Russell Senior <russell@personaltelco.net>
[fix SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "ar7240.dtsi"
+#include "ar724x_ubnt_xm.dtsi"
+#include "ar724x_ubnt_xm_outdoor.dtsi"
+
+/ {
+ compatible = "ubnt,bullet-m-ar7240", "ubnt,xm", "qca,ar7240";
+ model = "Ubiquiti Bullet M XM (AR7240)";
+};
+
+ð0 {
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+};
+
+ð1 {
+ compatible = "syscon", "simple-mfd";
+};
trendnet,tew-823dru)
ucidef_set_led_netdev "wan" "WAN" "trendnet:green:planet" "eth0"
;;
+ubnt,bullet-m-ar7240|\
ubnt,bullet-m-ar7241|\
ubnt,bullet-m-xw|\
ubnt,nanostation-loco-m|\
tplink,re450-v1|\
tplink,re450-v2|\
tplink,tl-wr902ac-v1|\
+ ubnt,bullet-m-ar7240|\
ubnt,bullet-m-ar7241|\
ubnt,bullet-m-xw|\
ubnt,lap-120|\
label_mac=$wan_mac
;;
ubnt,airrouter|\
+ ubnt,bullet-m-ar7240|\
ubnt,bullet-m-ar7241|\
ubnt,nanostation-loco-m|\
ubnt,nanostation-m|\
tplink,tl-wr2543-v1|\
tplink,tl-wr842n-v1|\
ubnt,airrouter|\
+ ubnt,bullet-m-ar7240|\
ubnt,bullet-m-ar7241|\
ubnt,nanostation-loco-m|\
ubnt,nanostation-m|\
endef
TARGET_DEVICES += ubnt_airrouter
+define Device/ubnt_bullet-m-ar7240
+ $(Device/ubnt-xm)
+ SOC := ar7240
+ DEVICE_MODEL := Bullet-M
+ DEVICE_VARIANT := XM (AR7240)
+ DEVICE_PACKAGES += rssileds
+ SUPPORTED_DEVICES += bullet-m
+endef
+TARGET_DEVICES += ubnt_bullet-m-ar7240
+
define Device/ubnt_bullet-m-ar7241
$(Device/ubnt-xm)
SOC := ar7241