bmips: add support for Comtrend WAP-5813n

The Comtrend WAP-5813n is a wifi gigabit router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM6369
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 64 MB DDR
 - Flash: 8 MB parallel NOR
 - LAN switch: Broadcom BCM53115, 5x 1Gbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM4322 802.11bgn
 - USB: 1x 2.0 (optional)
 - Buttons: 3x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the power switch.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit c3b1ef2dfd)

diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
index fb7cca17e5b6b7ed072b326aeebc83bb92b31453..c7e61fe72f35a63daf992c78eda3203a0bd1fc5b 100644 (file)
--- a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
+++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
@@ -6,6 +6,9 @@
 board_config_update
 
 case "$(board_name)" in
+comtrend,wap-5813n)
+       ucidef_set_led_usbport "usb" "USB" "green:usb" "usb1-port1" "usb2-port1"
+       ;;
 netgear,dgnd3700-v1 |\
 netgear,dgnd3800b)
        ucidef_set_led_netdev "lan" "LAN" "green:lan" "switch.1"

diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
index 1b47e5a76f367fb95645b5e0648f101e4a12624f..58fba05fec3a3e2a5b6155ba61dc20acf7bf9f79 100644 (file)
--- a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
+++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
@@ -14,6 +14,7 @@ comtrend,vr-3025un)
        ucidef_set_bridge_device switch
        ucidef_set_interface_lan "lan1 lan2 lan3 iptv"
        ;;
+comtrend,wap-5813n |\
 netgear,dgnd3700-v1 |\
 netgear,dgnd3800b |\
 netgear,evg2000)

diff --git a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc
index 729931794799fe8d398f7f12a85b3b5c1e210049..63d10c9a8e8082e6d4152960d23004b7f86d4535 100644 (file)
--- a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc
+++ b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc
@@ -5,6 +5,7 @@
 case "$(board_name)" in
 comtrend,vr-3025u |\
 comtrend,vr-3025un |\
+comtrend,wap-5813n |\
 netgear,evg2000 |\
 observa,vh4032n)
        mtd fixtrx firmware

diff --git a/target/linux/bmips/dts/bcm6369-comtrend-wap-5813n.dts b/target/linux/bmips/dts/bcm6369-comtrend-wap-5813n.dts
new file mode 100644 (file)
index 0000000..517a894
--- /dev/null
+++ b/target/linux/bmips/dts/bcm6369-comtrend-wap-5813n.dts
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "bcm6368.dtsi"
+
+/ {
+       model = "Comtrend WAP-5813n";
+       compatible = "comtrend,wap-5813n", "brcm,bcm6369", "brcm,bcm6368";
+
+       aliases {
+               led-boot = &led_power_green;
+               led-failsafe = &led_power_red;
+               led-running = &led_power_green;
+               led-upgrade = &led_power_green;
+       };
+
+       keys {
+               compatible = "gpio-keys-polled";
+               poll-interval = <100>;
+
+               wlan {
+                       label = "wlan";
+                       gpios = <&gpio 32 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WLAN>;
+                       debounce-interval = <60>;
+               };
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+                       debounce-interval = <60>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+                       debounce-interval = <60>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led@5 {
+                       label = "green:internet";
+                       gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
+               };
+
+               led@14 {
+                       label = "green:usb";
+                       gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+               };
+
+               led_power_green: led@22 {
+                       label = "green:power";
+                       gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+               };
+
+               led@23 {
+                       label = "green:wps";
+                       gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+               };
+
+               led_power_red: led@24 {
+                       label = "red:power";
+                       gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+                       panic-indicator;
+               };
+
+               led@31 {
+                       label = "red:internet";
+                       gpios = <&gpio 31 GPIO_ACTIVE_HIGH>;
+               };
+       };
+
+       bcm4322-sprom {
+               compatible = "brcm,ssb-sprom";
+
+               pci-bus = <0>;
+               pci-dev = <1>;
+
+               nvmem-cells = <&macaddr_cfe_6a0>;
+               nvmem-cell-names = "mac-address";
+               mac-address-increment = <1>;
+
+               brcm,sprom = "brcm/bcm4322-sprom.bin";
+               brcm,sprom-fixups = <97 0xfeed>,
+                                   <98 0x15d1>,
+                                   <99 0xfb0d>,
+                                   <113 0xfef7>,
+                                   <114 0x15f7>,
+                                   <115 0xfb1a>;
+       };
+};
+
+&ehci {
+       status = "okay";
+};
+
+&ethernet {
+       status = "okay";
+
+       nvmem-cells = <&macaddr_cfe_6a0>;
+       nvmem-cell-names = "mac-address";
+};
+
+&lsspi {
+       status = "okay";
+
+       switch@0 {
+               compatible = "brcm,bcm53115";
+               reg = <0>;
+               spi-max-frequency = <781000>;
+               dsa,member = <1 0>;
+
+               ports {
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+
+                       port@0 {
+                               reg = <0>;
+                               label = "lan4";
+                       };
+
+                       port@1 {
+                               reg = <1>;
+                               label = "lan3";
+                       };
+
+                       port@2 {
+                               reg = <2>;
+                               label = "lan2";
+                       };
+
+                       port@3 {
+                               reg = <3>;
+                               label = "lan1";
+                       };
+
+                       port@4 {
+                               reg = <4>;
+                               label = "wan";
+                       };
+
+                       port@5 {
+                               reg = <5>;
+
+                               phy-mode = "rgmii";
+                               ethernet = <&switch0port4>;
+
+                               fixed-link {
+                                       speed = <1000>;
+                                       full-duplex;
+                               };
+                       };
+               };
+       };
+};
+
+&pflash {
+       status = "okay";
+
+       partitions {
+               compatible = "fixed-partitions";
+               #address-cells = <1>;
+               #size-cells = <1>;
+
+               cfe: partition@0 {
+                       label = "CFE";
+                       reg = <0x000000 0x010000>;
+                       read-only;
+               };
+
+               partition@20000 {
+                       label = "firmware";
+                       reg = <0x010000 0x7e0000>;
+                       compatible = "brcm,bcm963xx-imagetag";
+               };
+
+               partition@fe0000 {
+                       label = "nvram";
+                       reg = <0x7f0000 0x010000>;
+               };
+       };
+};
+
+&ohci {
+       status = "okay";
+};
+
+&pci {
+       status = "okay";
+};
+
+&switch0 {
+       dsa,member = <0 0>;
+
+       ports {
+               switch0port4: port@4 {
+                       reg = <4>;
+                       label = "extsw";
+
+                       phy-mode = "rgmii";
+
+                       fixed-link {
+                               speed = <1000>;
+                               full-duplex;
+                       };
+               };
+       };
+};
+
+&uart0 {
+       status = "okay";
+};
+
+&usbh {
+       status = "okay";
+};
+
+&cfe {
+       compatible = "nvmem-cells";
+       #address-cells = <1>;
+       #size-cells = <1>;
+
+       macaddr_cfe_6a0: macaddr@6a0 {
+               reg = <0x6a0 0x6>;
+       };
+};

diff --git a/target/linux/bmips/image/bcm6368.mk b/target/linux/bmips/image/bcm6368.mk
index 67f8bbb09f0b9e1b4c26d89f8b0caf79746065ee..83cd096959ba30bdfd255bc8f7236f67aa842e15 100644 (file)
--- a/target/linux/bmips/image/bcm6368.mk
+++ b/target/linux/bmips/image/bcm6368.mk
@@ -27,6 +27,20 @@ define Device/comtrend_vr-3025un
 endef
 TARGET_DEVICES += comtrend_vr-3025un
 
+define Device/comtrend_wap-5813n
+  $(Device/bcm63xx-cfe)
+  DEVICE_VENDOR := Comtrend
+  DEVICE_MODEL := WAP-5813n
+  CHIP_ID := 6368
+  SOC := bcm6369
+  CFE_BOARD_ID := 96369R-1231N
+  FLASH_MB := 8
+  DEVICE_PACKAGES += $(USB2_PACKAGES) \
+    $(B43_PACKAGES) broadcom-4322-sprom \
+    kmod-leds-gpio
+endef
+TARGET_DEVICES += comtrend_wap-5813n
+
 define Device/netgear_dgnd3700-v1
   $(Device/bcm63xx-netgear)
   DEVICE_VENDOR := NETGEAR