--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "mt7981.dtsi"
+
+/ {
+ model = "H3C Magic NX30 Pro";
+ compatible = "h3c,magic-nx30-pro", "mediatek,mt7981";
+
+ aliases {
+ serial0 = &uart0;
+ led-boot = &led_status_green;
+ led-failsafe = &led_status_red;
+ led-running = &led_status_green;
+ led-upgrade = &led_status_red;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0 0x40000000 0 0x10000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_green: green {
+ label = "green:status";
+ gpios = <&pio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_red: red {
+ label = "red:status";
+ gpios = <&pio 5 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ gmac1: mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "gmii";
+ phy-handle = <&int_gbe_phy>;
+ };
+};
+
+&mdio_bus {
+ switch: switch@0 {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ spi_nand@0 {
+ compatible = "spi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+
+ spi-max-frequency = <52000000>;
+ spi-tx-buswidth = <4>;
+ spi-rx-buswidth = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "BL2";
+ reg = <0x0000000 0x0100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "u-boot-env";
+ reg = <0x0100000 0x0080000>;
+ };
+
+ factory: partition@180000 {
+ label = "Factory";
+ reg = <0x0180000 0x0200000>;
+ read-only;
+ };
+
+ partition@380000 {
+ label = "FIP";
+ reg = <0x0380000 0x0200000>;
+ read-only;
+ };
+
+ partition@580000 {
+ label = "ubi";
+ reg = <0x0580000 0x4000000>;
+ };
+
+ /* yaffs partition */
+ partition@4580000 {
+ label = "pdt_data";
+ reg = <0x4580000 0x0600000>;
+ read-only;
+ };
+
+ /* yaffs partition */
+ partition@4b80000 {
+ label = "pdt_data_1";
+ reg = <0x4b80000 0x0600000>;
+ read-only;
+ };
+
+ partition@5180000 {
+ label = "exp";
+ reg = <0x5180000 0x0100000>;
+ read-only;
+ };
+
+ partition@5280000 {
+ label = "plugin";
+ reg = <0x5280000 0x2580000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@6 {
+ reg = <6>;
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <8>;
+ mediatek,pull-up-adv = <0>; /* bias-disable */
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <8>;
+ mediatek,pull-up-adv = <0>; /* bias-disable */
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi {
+ status = "okay";
+
+ mediatek,mtd-eeprom = <&factory 0x0>;
+};
endef
TARGET_DEVICES += glinet_gl-mt3000
+define Device/h3c_magic-nx30-pro
+ DEVICE_VENDOR := H3C
+ DEVICE_MODEL := Magic NX30 Pro
+ DEVICE_DTS := mt7981b-h3c-magic-nx30-pro
+ DEVICE_DTS_DIR := ../dts
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_IN_UBI := 1
+ UBOOTENV_IN_UBI := 1
+ IMAGE_SIZE := 65536k
+ IMAGES := sysupgrade.itb
+ KERNEL_INITRAMFS_SUFFIX := -recovery.itb
+ KERNEL := kernel-bin | gzip
+ KERNEL_INITRAMFS := kernel-bin | lzma | \
+ fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
+ IMAGE/sysupgrade.itb := append-kernel | \
+ fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
+ DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
+ ARTIFACTS := preloader.bin bl31-uboot.fip
+ ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
+ ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot h3c_magic-nx30-pro
+endef
+TARGET_DEVICES += h3c_magic-nx30-pro
+
define Device/netgear_wax220
DEVICE_VENDOR := Netgear
DEVICE_MODEL := WAX220
projects / openwrt / staging / dangole.git / commitdiff