--- /dev/null
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -506,6 +506,7 @@
+ qcom-apq8084-ifc6540.dtb \
+ qcom-apq8084-mtp.dtb \
+ qcom-ipq8064-ap148.dtb \
++ qcom-ipq8064-c2600.dtb \
+ qcom-ipq8064-db149.dtb \
+ qcom-ipq8064-r7500.dtb \
+ qcom-ipq8064-d7800.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
+@@ -0,0 +1,412 @@
++#include "qcom-ipq8064-v1.0.dtsi"
++#include <dt-bindings/input/input.h>
++
++/ {
++ model = "TP-Link Archer C2600";
++ compatible = "tplink,c2600", "qcom,ipq8064";
++
++ memory@0 {
++ reg = <0x42000000 0x1e000000>;
++ device_type = "memory";
++ };
++
++ reserved-memory {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ ranges;
++ rsvd@41200000 {
++ reg = <0x41200000 0x300000>;
++ no-map;
++ };
++ };
++
++ aliases {
++ serial0 = &uart4;
++ mdio-gpio0 = &mdio0;
++ };
++
++ chosen {
++ linux,stdout-path = "serial0:115200n8";
++ };
++
++ soc {
++ pinmux@800000 {
++ i2c4_pins: i2c4_pinmux {
++ pins = "gpio12", "gpio13";
++ function = "gsbi4";
++ bias-disable;
++ };
++
++ spi_pins: spi_pins {
++ mux {
++ pins = "gpio18", "gpio19", "gpio21";
++ function = "gsbi5";
++ drive-strength = <10>;
++ bias-none;
++ };
++ };
++
++ nand_pins: nand_pins {
++ mux {
++ pins = "gpio34", "gpio35", "gpio36",
++ "gpio37", "gpio38", "gpio39",
++ "gpio40", "gpio41", "gpio42",
++ "gpio43", "gpio44", "gpio45",
++ "gpio46", "gpio47";
++ function = "nand";
++ drive-strength = <10>;
++ bias-disable;
++ };
++
++ pullups {
++ pins = "gpio39";
++ bias-pull-up;
++ };
++
++ hold {
++ pins = "gpio40", "gpio41", "gpio42",
++ "gpio43", "gpio44", "gpio45",
++ "gpio46", "gpio47";
++ bias-bus-hold;
++ };
++ };
++
++ mdio0_pins: mdio0_pins {
++ mux {
++ pins = "gpio0", "gpio1";
++ function = "gpio";
++ drive-strength = <8>;
++ bias-disable;
++ };
++ };
++
++ rgmii2_pins: rgmii2_pins {
++ mux {
++ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
++ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
++ function = "rgmii2";
++ drive-strength = <8>;
++ bias-disable;
++ };
++ };
++ };
++
++ gsbi@16300000 {
++ qcom,mode = <GSBI_PROT_I2C_UART>;
++ status = "ok";
++ serial@16340000 {
++ status = "ok";
++ };
++ /*
++ * The i2c device on gsbi4 should not be enabled.
++ * On ipq806x designs gsbi4 i2c is meant for exclusive
++ * RPM usage. Turning this on in kernel manifests as
++ * i2c failure for the RPM.
++ */
++ };
++
++ gsbi5: gsbi@1a200000 {
++ qcom,mode = <GSBI_PROT_SPI>;
++ status = "ok";
++
++ spi4: spi@1a280000 {
++ status = "ok";
++ spi-max-frequency = <50000000>;
++
++ pinctrl-0 = <&spi_pins>;
++ pinctrl-names = "default";
++
++ cs-gpios = <&qcom_pinmux 20 0>;
++
++ flash: m25p80@0 {
++ compatible = "s25fl256s1";
++ #address-cells = <1>;
++ #size-cells = <1>;
++ spi-max-frequency = <50000000>;
++ reg = <0>;
++
++ SBL1@0 {
++ label = "SBL1";
++ reg = <0x0 0x20000>;
++ read-only;
++ };
++ MIBIB@20000 {
++ label = "MIBIB";
++ reg = <0x20000 0x20000>;
++ read-only;
++ };
++ SBL2@40000 {
++ label = "SBL2";
++ reg = <0x40000 0x20000>;
++ read-only;
++ };
++ SBL3@60000 {
++ label = "SBL3";
++ reg = <0x60000 0x30000>;
++ read-only;
++ };
++ DDRCONFIG@90000 {
++ label = "DDRCONFIG";
++ reg = <0x90000 0x10000>;
++ read-only;
++ };
++ SSD@a0000 {
++ label = "SSD";
++ reg = <0xa0000 0x10000>;
++ read-only;
++ };
++ TZ@b0000 {
++ label = "TZ";
++ reg = <0xb0000 0x30000>;
++ read-only;
++ };
++ RPM@e0000 {
++ label = "RPM";
++ reg = <0xe0000 0x20000>;
++ read-only;
++ };
++ fs-uboot@100000 {
++ label = "fs-uboot";
++ reg = <0x100000 0x70000>;
++ read-only;
++ };
++ uboot-env@170000 {
++ label = "uboot-env";
++ reg = <0x170000 0x40000>;
++ read-only;
++ };
++ radio@1b0000 {
++ label = "radio";
++ reg = <0x1b0000 0x40000>;
++ read-only;
++ };
++ os-image@1f0000 {
++ label = "os-image";
++ reg = <0x1f0000 0x200000>;
++ };
++ rootfs@3f0000 {
++ label = "rootfs";
++ reg = <0x3f0000 0x1b00000>;
++ };
++ defaultmac: default-mac@1ef0000 {
++ label = "default-mac";
++ reg = <0x1ef0000 0x00200>;
++ read-only;
++ };
++ pin@1ef0200 {
++ label = "pin";
++ reg = <0x1ef0200 0x00200>;
++ read-only;
++ };
++ product-info@1ef0400 {
++ label = "product-info";
++ reg = <0x1ef0400 0x0fc00>;
++ read-only;
++ };
++ partition-table@1f00000 {
++ label = "partition-table";
++ reg = <0x1f00000 0x10000>;
++ read-only;
++ };
++ soft-version@1f10000 {
++ label = "soft-version";
++ reg = <0x1f10000 0x10000>;
++ read-only;
++ };
++ support-list@1f20000 {
++ label = "support-list";
++ reg = <0x1f20000 0x10000>;
++ read-only;
++ };
++ profile@1f30000 {
++ label = "profile";
++ reg = <0x1f30000 0x10000>;
++ read-only;
++ };
++ default-config@1f40000 {
++ label = "default-config";
++ reg = <0x1f40000 0x10000>;
++ read-only;
++ };
++ user-config@1f50000 {
++ label = "user-config";
++ reg = <0x1f50000 0x40000>;
++ read-only;
++ };
++ qos-db@1f90000 {
++ label = "qos-db";
++ reg = <0x1f90000 0x40000>;
++ read-only;
++ };
++ usb-config@1fd0000 {
++ label = "usb-config";
++ reg = <0x1fd0000 0x10000>;
++ read-only;
++ };
++ log@1fe0000 {
++ label = "log";
++ reg = <0x1fe0000 0x20000>;
++ read-only;
++ };
++ };
++ };
++ };
++
++ phy@100f8800 { /* USB3 port 1 HS phy */
++ status = "ok";
++ };
++
++ phy@100f8830 { /* USB3 port 1 SS phy */
++ status = "ok";
++ };
++
++ phy@110f8800 { /* USB3 port 0 HS phy */
++ status = "ok";
++ };
++
++ phy@110f8830 { /* USB3 port 0 SS phy */
++ status = "ok";
++ };
++
++ usb30@0 {
++ status = "ok";
++ };
++
++ usb30@1 {
++ status = "ok";
++ };
++
++ pcie0: pci@1b500000 {
++ status = "ok";
++ phy-tx0-term-offset = <7>;
++ };
++
++ pcie1: pci@1b700000 {
++ status = "ok";
++ phy-tx0-term-offset = <7>;
++ };
++
++ mdio0: mdio {
++ compatible = "virtual,mdio-gpio";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
++ pinctrl-0 = <&mdio0_pins>;
++ pinctrl-names = "default";
++
++ phy0: ethernet-phy@0 {
++ device_type = "ethernet-phy";
++ reg = <0>;
++ qca,ar8327-initvals = <
++ 0x00004 0x7600000 /* PAD0_MODE */
++ 0x00008 0x1000000 /* PAD5_MODE */
++ 0x0000c 0x80 /* PAD6_MODE */
++ 0x000e4 0xaa545 /* MAC_POWER_SEL */
++ 0x000e0 0xc74164de /* SGMII_CTRL */
++ 0x0007c 0x4e /* PORT0_STATUS */
++ 0x00094 0x4e /* PORT6_STATUS */
++ >;
++ };
++
++ phy4: ethernet-phy@4 {
++ device_type = "ethernet-phy";
++ reg = <4>;
++ };
++ };
++
++ gmac1: ethernet@37200000 {
++ status = "ok";
++ phy-mode = "rgmii";
++ qcom,id = <1>;
++
++ pinctrl-0 = <&rgmii2_pins>;
++ pinctrl-names = "default";
++
++ mtd-mac-address = <&defaultmac 0x8>;
++ mtd-mac-address-increment = <1>;
++
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++
++ gmac2: ethernet@37400000 {
++ status = "ok";
++ phy-mode = "sgmii";
++ qcom,id = <2>;
++
++ mtd-mac-address = <&defaultmac 0x8>;
++
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++
++ wifi {
++ label = "wifi";
++ gpios = <&qcom_pinmux 49 1>;
++ linux,code = <KEY_WLAN>;
++ };
++
++ reset {
++ label = "reset";
++ gpios = <&qcom_pinmux 64 1>;
++ linux,code = <KEY_RESTART>;
++ };
++
++ wps {
++ label = "wps";
++ gpios = <&qcom_pinmux 65 1>;
++ linux,code = <KEY_WPS_BUTTON>;
++ };
++ ledgeneral {
++ label = "ledgeneral";
++ gpios = <&qcom_pinmux 16 1>;
++ linux,code = <KEY_DOLLAR>;
++ };
++ };
++
++ gpio-leds {
++ compatible = "gpio-leds";
++
++ lan {
++ label = "lan:blue";
++ gpios = <&qcom_pinmux 6 0>;
++ };
++ usb4 {
++ label = "usb_4:blue";
++ gpios = <&qcom_pinmux 7 0>;
++ };
++ usb2 {
++ label = "usb_2:blue";
++ gpios = <&qcom_pinmux 8 0>;
++ };
++ wps {
++ label = "wps:blue";
++ gpios = <&qcom_pinmux 9 0>;
++ };
++ wan_blue {
++ label = "wan:blue";
++ gpios = <&qcom_pinmux 33 1>;
++ };
++ status {
++ label = "status:blue";
++ gpios = <&qcom_pinmux 53 0>;
++ default-state = "on";
++ };
++ ledgnr {
++ label = "ledgnr:blue";
++ gpios = <&qcom_pinmux 66 0>;
++ };
++ };
++};
++
++&adm_dma {
++ status = "ok";
++};
projects / openwrt / staging / blogic.git / commitdiff