net: dsa: fully divert PHY reads/writes if requested

In case a PHY is found via Device Tree, and is also flagged by the
switch driver as needing indirect reads/writes using the switch driver
implemented MDIO bus, make sure that we bind this PHY to the slave MII
bus in order for this to happen.

Without this, we would succeed in having the PHY driver probe()'s
function to use slave MII bus read/write functions, because this is done
during dsa_slave_mii_init(), but past that point, the PHY driver would
not go through these diverted reads and writes.

Fixes: 0d8bcdd383b88 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/net/dsa/slave.c b/net/dsa/slave.c
index 19bc2b39c9d15f67e90f64e5c402a37ab836de80..188b69773e702d2ab6cb84bd520226894efc2f28 100644 (file)
--- a/net/dsa/slave.c
+++ b/net/dsa/slave.c
@@ -618,11 +618,12 @@ static int dsa_slave_fixed_link_update(struct net_device *dev,
 
 /* slave device setup *******************************************************/
 static int dsa_slave_phy_connect(struct dsa_slave_priv *p,
-                                struct net_device *slave_dev)
+                                struct net_device *slave_dev,
+                                int addr)
 {
        struct dsa_switch *ds = p->parent;
 
-       p->phy = ds->slave_mii_bus->phy_map[p->port];
+       p->phy = ds->slave_mii_bus->phy_map[addr];
        if (!p->phy)
                return -ENODEV;
 
@@ -667,10 +668,24 @@ static int dsa_slave_phy_setup(struct dsa_slave_priv *p,
        if (ds->drv->get_phy_flags)
                phy_flags = ds->drv->get_phy_flags(ds, p->port);
 
-       if (phy_dn)
-               p->phy = of_phy_connect(slave_dev, phy_dn,
-                                       dsa_slave_adjust_link, phy_flags,
-                                       p->phy_interface);
+       if (phy_dn) {
+               ret = of_mdio_parse_addr(&slave_dev->dev, phy_dn);
+               /* If this PHY address is part of phys_mii_mask, which means
+                * that we need to divert reads and writes to/from it, then we
+                * want to bind this device using the slave MII bus created by
+                * DSA to make that happen.
+                */
+               if (ret >= 0 && (ds->phys_mii_mask & (1 << ret))) {
+                       ret = dsa_slave_phy_connect(p, slave_dev, ret);
+                       if (ret)
+                               return ret;
+               } else {
+                       p->phy = of_phy_connect(slave_dev, phy_dn,
+                                               dsa_slave_adjust_link,
+                                               phy_flags,
+                                               p->phy_interface);
+               }
+       }
 
        if (p->phy && phy_is_fixed)
                fixed_phy_set_link_update(p->phy, dsa_slave_fixed_link_update);
@@ -679,7 +694,7 @@ static int dsa_slave_phy_setup(struct dsa_slave_priv *p,
         * MDIO bus instead
         */
        if (!p->phy) {
-               ret = dsa_slave_phy_connect(p, slave_dev);
+               ret = dsa_slave_phy_connect(p, slave_dev, p->port);
                if (ret)
                        return ret;
        } else {