-#ifdef __uClinux__
-#include "dma_no.h"
+#ifndef _M68K_DMA_H
+#define _M68K_DMA_H 1
+
+#ifdef CONFIG_COLDFIRE
+/*
+ * ColdFire DMA Model:
+ * ColdFire DMA supports two forms of DMA: Single and Dual address. Single
+ * address mode emits a source address, and expects that the device will either
+ * pick up the data (DMA READ) or source data (DMA WRITE). This implies that
+ * the device will place data on the correct byte(s) of the data bus, as the
+ * memory transactions are always 32 bits. This implies that only 32 bit
+ * devices will find single mode transfers useful. Dual address DMA mode
+ * performs two cycles: source read and destination write. ColdFire will
+ * align the data so that the device will always get the correct bytes, thus
+ * is useful for 8 and 16 bit devices. This is the mode that is supported
+ * below.
+ *
+ * AUG/22/2000 : added support for 32-bit Dual-Address-Mode (K) 2000
+ * Oliver Kamphenkel (O.Kamphenkel@tu-bs.de)
+ *
+ * AUG/25/2000 : addad support for 8, 16 and 32-bit Single-Address-Mode (K)2000
+ * Oliver Kamphenkel (O.Kamphenkel@tu-bs.de)
+ *
+ * APR/18/2002 : added proper support for MCF5272 DMA controller.
+ * Arthur Shipkowski (art@videon-central.com)
+ */
+
+#include <asm/coldfire.h>
+#include <asm/mcfsim.h>
+#include <asm/mcfdma.h>
+
+/*
+ * Set number of channels of DMA on ColdFire for different implementations.
+ */
+#if defined(CONFIG_M5249) || defined(CONFIG_M5307) || defined(CONFIG_M5407) || \
+ defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x)
+#define MAX_M68K_DMA_CHANNELS 4
+#elif defined(CONFIG_M5272)
+#define MAX_M68K_DMA_CHANNELS 1
+#elif defined(CONFIG_M532x)
+#define MAX_M68K_DMA_CHANNELS 0
#else
-#include "dma_mm.h"
+#define MAX_M68K_DMA_CHANNELS 2
#endif
+
+extern unsigned int dma_base_addr[MAX_M68K_DMA_CHANNELS];
+extern unsigned int dma_device_address[MAX_M68K_DMA_CHANNELS];
+
+#if !defined(CONFIG_M5272)
+#define DMA_MODE_WRITE_BIT 0x01 /* Memory/IO to IO/Memory select */
+#define DMA_MODE_WORD_BIT 0x02 /* 8 or 16 bit transfers */
+#define DMA_MODE_LONG_BIT 0x04 /* or 32 bit transfers */
+#define DMA_MODE_SINGLE_BIT 0x08 /* single-address-mode */
+
+/* I/O to memory, 8 bits, mode */
+#define DMA_MODE_READ 0
+/* memory to I/O, 8 bits, mode */
+#define DMA_MODE_WRITE 1
+/* I/O to memory, 16 bits, mode */
+#define DMA_MODE_READ_WORD 2
+/* memory to I/O, 16 bits, mode */
+#define DMA_MODE_WRITE_WORD 3
+/* I/O to memory, 32 bits, mode */
+#define DMA_MODE_READ_LONG 4
+/* memory to I/O, 32 bits, mode */
+#define DMA_MODE_WRITE_LONG 5
+/* I/O to memory, 8 bits, single-address-mode */
+#define DMA_MODE_READ_SINGLE 8
+/* memory to I/O, 8 bits, single-address-mode */
+#define DMA_MODE_WRITE_SINGLE 9
+/* I/O to memory, 16 bits, single-address-mode */
+#define DMA_MODE_READ_WORD_SINGLE 10
+/* memory to I/O, 16 bits, single-address-mode */
+#define DMA_MODE_WRITE_WORD_SINGLE 11
+/* I/O to memory, 32 bits, single-address-mode */
+#define DMA_MODE_READ_LONG_SINGLE 12
+/* memory to I/O, 32 bits, single-address-mode */
+#define DMA_MODE_WRITE_LONG_SINGLE 13
+
+#else /* CONFIG_M5272 is defined */
+
+/* Source static-address mode */
+#define DMA_MODE_SRC_SA_BIT 0x01
+/* Two bits to select between all four modes */
+#define DMA_MODE_SSIZE_MASK 0x06
+/* Offset to shift bits in */
+#define DMA_MODE_SSIZE_OFF 0x01
+/* Destination static-address mode */
+#define DMA_MODE_DES_SA_BIT 0x10
+/* Two bits to select between all four modes */
+#define DMA_MODE_DSIZE_MASK 0x60
+/* Offset to shift bits in */
+#define DMA_MODE_DSIZE_OFF 0x05
+/* Size modifiers */
+#define DMA_MODE_SIZE_LONG 0x00
+#define DMA_MODE_SIZE_BYTE 0x01
+#define DMA_MODE_SIZE_WORD 0x02
+#define DMA_MODE_SIZE_LINE 0x03
+
+/*
+ * Aliases to help speed quick ports; these may be suboptimal, however. They
+ * do not include the SINGLE mode modifiers since the MCF5272 does not have a
+ * mode where the device is in control of its addressing.
+ */
+
+/* I/O to memory, 8 bits, mode */
+#define DMA_MODE_READ ((DMA_MODE_SIZE_BYTE << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_BYTE << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT)
+/* memory to I/O, 8 bits, mode */
+#define DMA_MODE_WRITE ((DMA_MODE_SIZE_BYTE << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_BYTE << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT)
+/* I/O to memory, 16 bits, mode */
+#define DMA_MODE_READ_WORD ((DMA_MODE_SIZE_WORD << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_WORD << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT)
+/* memory to I/O, 16 bits, mode */
+#define DMA_MODE_WRITE_WORD ((DMA_MODE_SIZE_WORD << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_WORD << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT)
+/* I/O to memory, 32 bits, mode */
+#define DMA_MODE_READ_LONG ((DMA_MODE_SIZE_LONG << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_LONG << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT)
+/* memory to I/O, 32 bits, mode */
+#define DMA_MODE_WRITE_LONG ((DMA_MODE_SIZE_LONG << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_LONG << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT)
+
+#endif /* !defined(CONFIG_M5272) */
+
+#if !defined(CONFIG_M5272)
+/* enable/disable a specific DMA channel */
+static __inline__ void enable_dma(unsigned int dmanr)
+{
+ volatile unsigned short *dmawp;
+
+#ifdef DMA_DEBUG
+ printk("enable_dma(dmanr=%d)\n", dmanr);
+#endif
+
+ dmawp = (unsigned short *) dma_base_addr[dmanr];
+ dmawp[MCFDMA_DCR] |= MCFDMA_DCR_EEXT;
+}
+
+static __inline__ void disable_dma(unsigned int dmanr)
+{
+ volatile unsigned short *dmawp;
+ volatile unsigned char *dmapb;
+
+#ifdef DMA_DEBUG
+ printk("disable_dma(dmanr=%d)\n", dmanr);
+#endif
+
+ dmawp = (unsigned short *) dma_base_addr[dmanr];
+ dmapb = (unsigned char *) dma_base_addr[dmanr];
+
+ /* Turn off external requests, and stop any DMA in progress */
+ dmawp[MCFDMA_DCR] &= ~MCFDMA_DCR_EEXT;
+ dmapb[MCFDMA_DSR] = MCFDMA_DSR_DONE;
+}
+
+/*
+ * Clear the 'DMA Pointer Flip Flop'.
+ * Write 0 for LSB/MSB, 1 for MSB/LSB access.
+ * Use this once to initialize the FF to a known state.
+ * After that, keep track of it. :-)
+ * --- In order to do that, the DMA routines below should ---
+ * --- only be used while interrupts are disabled! ---
+ *
+ * This is a NOP for ColdFire. Provide a stub for compatibility.
+ */
+static __inline__ void clear_dma_ff(unsigned int dmanr)
+{
+}
+
+/* set mode (above) for a specific DMA channel */
+static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
+{
+
+ volatile unsigned char *dmabp;
+ volatile unsigned short *dmawp;
+
+#ifdef DMA_DEBUG
+ printk("set_dma_mode(dmanr=%d,mode=%d)\n", dmanr, mode);
+#endif
+
+ dmabp = (unsigned char *) dma_base_addr[dmanr];
+ dmawp = (unsigned short *) dma_base_addr[dmanr];
+
+ // Clear config errors
+ dmabp[MCFDMA_DSR] = MCFDMA_DSR_DONE;
+
+ // Set command register
+ dmawp[MCFDMA_DCR] =
+ MCFDMA_DCR_INT | // Enable completion irq
+ MCFDMA_DCR_CS | // Force one xfer per request
+ MCFDMA_DCR_AA | // Enable auto alignment
+ // single-address-mode
+ ((mode & DMA_MODE_SINGLE_BIT) ? MCFDMA_DCR_SAA : 0) |
+ // sets s_rw (-> r/w) high if Memory to I/0
+ ((mode & DMA_MODE_WRITE_BIT) ? MCFDMA_DCR_S_RW : 0) |
+ // Memory to I/O or I/O to Memory
+ ((mode & DMA_MODE_WRITE_BIT) ? MCFDMA_DCR_SINC : MCFDMA_DCR_DINC) |
+ // 32 bit, 16 bit or 8 bit transfers
+ ((mode & DMA_MODE_WORD_BIT) ? MCFDMA_DCR_SSIZE_WORD :
+ ((mode & DMA_MODE_LONG_BIT) ? MCFDMA_DCR_SSIZE_LONG :
+ MCFDMA_DCR_SSIZE_BYTE)) |
+ ((mode & DMA_MODE_WORD_BIT) ? MCFDMA_DCR_DSIZE_WORD :
+ ((mode & DMA_MODE_LONG_BIT) ? MCFDMA_DCR_DSIZE_LONG :
+ MCFDMA_DCR_DSIZE_BYTE));
+
+#ifdef DEBUG_DMA
+ printk("%s(%d): dmanr=%d DSR[%x]=%x DCR[%x]=%x\n", __FILE__, __LINE__,
+ dmanr, (int) &dmabp[MCFDMA_DSR], dmabp[MCFDMA_DSR],
+ (int) &dmawp[MCFDMA_DCR], dmawp[MCFDMA_DCR]);
+#endif
+}
+
+/* Set transfer address for specific DMA channel */
+static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
+{
+ volatile unsigned short *dmawp;
+ volatile unsigned int *dmalp;
+
+#ifdef DMA_DEBUG
+ printk("set_dma_addr(dmanr=%d,a=%x)\n", dmanr, a);
+#endif
+
+ dmawp = (unsigned short *) dma_base_addr[dmanr];
+ dmalp = (unsigned int *) dma_base_addr[dmanr];
+
+ // Determine which address registers are used for memory/device accesses
+ if (dmawp[MCFDMA_DCR] & MCFDMA_DCR_SINC) {
+ // Source incrementing, must be memory
+ dmalp[MCFDMA_SAR] = a;
+ // Set dest address, must be device
+ dmalp[MCFDMA_DAR] = dma_device_address[dmanr];
+ } else {
+ // Destination incrementing, must be memory
+ dmalp[MCFDMA_DAR] = a;
+ // Set source address, must be device
+ dmalp[MCFDMA_SAR] = dma_device_address[dmanr];
+ }
+
+#ifdef DEBUG_DMA
+ printk("%s(%d): dmanr=%d DCR[%x]=%x SAR[%x]=%08x DAR[%x]=%08x\n",
+ __FILE__, __LINE__, dmanr, (int) &dmawp[MCFDMA_DCR], dmawp[MCFDMA_DCR],
+ (int) &dmalp[MCFDMA_SAR], dmalp[MCFDMA_SAR],
+ (int) &dmalp[MCFDMA_DAR], dmalp[MCFDMA_DAR]);
+#endif
+}
+
+/*
+ * Specific for Coldfire - sets device address.
+ * Should be called after the mode set call, and before set DMA address.
+ */
+static __inline__ void set_dma_device_addr(unsigned int dmanr, unsigned int a)
+{
+#ifdef DMA_DEBUG
+ printk("set_dma_device_addr(dmanr=%d,a=%x)\n", dmanr, a);
+#endif
+
+ dma_device_address[dmanr] = a;
+}
+
+/*
+ * NOTE 2: "count" represents _bytes_.
+ */
+static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
+{
+ volatile unsigned short *dmawp;
+
+#ifdef DMA_DEBUG
+ printk("set_dma_count(dmanr=%d,count=%d)\n", dmanr, count);
+#endif
+
+ dmawp = (unsigned short *) dma_base_addr[dmanr];
+ dmawp[MCFDMA_BCR] = (unsigned short)count;
+}
+
+/*
+ * Get DMA residue count. After a DMA transfer, this
+ * should return zero. Reading this while a DMA transfer is
+ * still in progress will return unpredictable results.
+ * Otherwise, it returns the number of _bytes_ left to transfer.
+ */
+static __inline__ int get_dma_residue(unsigned int dmanr)
+{
+ volatile unsigned short *dmawp;
+ unsigned short count;
+
+#ifdef DMA_DEBUG
+ printk("get_dma_residue(dmanr=%d)\n", dmanr);
+#endif
+
+ dmawp = (unsigned short *) dma_base_addr[dmanr];
+ count = dmawp[MCFDMA_BCR];
+ return((int) count);
+}
+#else /* CONFIG_M5272 is defined */
+
+/*
+ * The MCF5272 DMA controller is very different than the controller defined above
+ * in terms of register mapping. For instance, with the exception of the 16-bit
+ * interrupt register (IRQ#85, for reference), all of the registers are 32-bit.
+ *
+ * The big difference, however, is the lack of device-requested DMA. All modes
+ * are dual address transfer, and there is no 'device' setup or direction bit.
+ * You can DMA between a device and memory, between memory and memory, or even between
+ * two devices directly, with any combination of incrementing and non-incrementing
+ * addresses you choose. This puts a crimp in distinguishing between the 'device
+ * address' set up by set_dma_device_addr.
+ *
+ * Therefore, there are two options. One is to use set_dma_addr and set_dma_device_addr,
+ * which will act exactly as above in -- it will look to see if the source is set to
+ * autoincrement, and if so it will make the source use the set_dma_addr value and the
+ * destination the set_dma_device_addr value. Otherwise the source will be set to the
+ * set_dma_device_addr value and the destination will get the set_dma_addr value.
+ *
+ * The other is to use the provided set_dma_src_addr and set_dma_dest_addr functions
+ * and make it explicit. Depending on what you're doing, one of these two should work
+ * for you, but don't mix them in the same transfer setup.
+ */
+
+/* enable/disable a specific DMA channel */
+static __inline__ void enable_dma(unsigned int dmanr)
+{
+ volatile unsigned int *dmalp;
+
+#ifdef DMA_DEBUG
+ printk("enable_dma(dmanr=%d)\n", dmanr);
+#endif
+
+ dmalp = (unsigned int *) dma_base_addr[dmanr];
+ dmalp[MCFDMA_DMR] |= MCFDMA_DMR_EN;
+}
+
+static __inline__ void disable_dma(unsigned int dmanr)
+{
+ volatile unsigned int *dmalp;
+
+#ifdef DMA_DEBUG
+ printk("disable_dma(dmanr=%d)\n", dmanr);
+#endif
+
+ dmalp = (unsigned int *) dma_base_addr[dmanr];
+
+ /* Turn off external requests, and stop any DMA in progress */
+ dmalp[MCFDMA_DMR] &= ~MCFDMA_DMR_EN;
+ dmalp[MCFDMA_DMR] |= MCFDMA_DMR_RESET;
+}
+
+/*
+ * Clear the 'DMA Pointer Flip Flop'.
+ * Write 0 for LSB/MSB, 1 for MSB/LSB access.
+ * Use this once to initialize the FF to a known state.
+ * After that, keep track of it. :-)
+ * --- In order to do that, the DMA routines below should ---
+ * --- only be used while interrupts are disabled! ---
+ *
+ * This is a NOP for ColdFire. Provide a stub for compatibility.
+ */
+static __inline__ void clear_dma_ff(unsigned int dmanr)
+{
+}
+
+/* set mode (above) for a specific DMA channel */
+static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
+{
+
+ volatile unsigned int *dmalp;
+ volatile unsigned short *dmawp;
+
+#ifdef DMA_DEBUG
+ printk("set_dma_mode(dmanr=%d,mode=%d)\n", dmanr, mode);
+#endif
+ dmalp = (unsigned int *) dma_base_addr[dmanr];
+ dmawp = (unsigned short *) dma_base_addr[dmanr];
+
+ // Clear config errors
+ dmalp[MCFDMA_DMR] |= MCFDMA_DMR_RESET;
+
+ // Set command register
+ dmalp[MCFDMA_DMR] =
+ MCFDMA_DMR_RQM_DUAL | // Mandatory Request Mode setting
+ MCFDMA_DMR_DSTT_SD | // Set up addressing types; set to supervisor-data.
+ MCFDMA_DMR_SRCT_SD | // Set up addressing types; set to supervisor-data.
+ // source static-address-mode
+ ((mode & DMA_MODE_SRC_SA_BIT) ? MCFDMA_DMR_SRCM_SA : MCFDMA_DMR_SRCM_IA) |
+ // dest static-address-mode
+ ((mode & DMA_MODE_DES_SA_BIT) ? MCFDMA_DMR_DSTM_SA : MCFDMA_DMR_DSTM_IA) |
+ // burst, 32 bit, 16 bit or 8 bit transfers are separately configurable on the MCF5272
+ (((mode & DMA_MODE_SSIZE_MASK) >> DMA_MODE_SSIZE_OFF) << MCFDMA_DMR_DSTS_OFF) |
+ (((mode & DMA_MODE_SSIZE_MASK) >> DMA_MODE_SSIZE_OFF) << MCFDMA_DMR_SRCS_OFF);
+
+ dmawp[MCFDMA_DIR] |= MCFDMA_DIR_ASCEN; /* Enable completion interrupts */
+
+#ifdef DEBUG_DMA
+ printk("%s(%d): dmanr=%d DMR[%x]=%x DIR[%x]=%x\n", __FILE__, __LINE__,
+ dmanr, (int) &dmalp[MCFDMA_DMR], dmabp[MCFDMA_DMR],
+ (int) &dmawp[MCFDMA_DIR], dmawp[MCFDMA_DIR]);
+#endif
+}
+
+/* Set transfer address for specific DMA channel */
+static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
+{
+ volatile unsigned int *dmalp;
+
+#ifdef DMA_DEBUG
+ printk("set_dma_addr(dmanr=%d,a=%x)\n", dmanr, a);
+#endif
+
+ dmalp = (unsigned int *) dma_base_addr[dmanr];
+
+ // Determine which address registers are used for memory/device accesses
+ if (dmalp[MCFDMA_DMR] & MCFDMA_DMR_SRCM) {
+ // Source incrementing, must be memory
+ dmalp[MCFDMA_DSAR] = a;
+ // Set dest address, must be device
+ dmalp[MCFDMA_DDAR] = dma_device_address[dmanr];
+ } else {
+ // Destination incrementing, must be memory
+ dmalp[MCFDMA_DDAR] = a;
+ // Set source address, must be device
+ dmalp[MCFDMA_DSAR] = dma_device_address[dmanr];
+ }
+
+#ifdef DEBUG_DMA
+ printk("%s(%d): dmanr=%d DMR[%x]=%x SAR[%x]=%08x DAR[%x]=%08x\n",
+ __FILE__, __LINE__, dmanr, (int) &dmawp[MCFDMA_DMR], dmawp[MCFDMA_DMR],
+ (int) &dmalp[MCFDMA_DSAR], dmalp[MCFDMA_DSAR],
+ (int) &dmalp[MCFDMA_DDAR], dmalp[MCFDMA_DDAR]);
+#endif
+}
+
+/*
+ * Specific for Coldfire - sets device address.
+ * Should be called after the mode set call, and before set DMA address.
+ */
+static __inline__ void set_dma_device_addr(unsigned int dmanr, unsigned int a)
+{
+#ifdef DMA_DEBUG
+ printk("set_dma_device_addr(dmanr=%d,a=%x)\n", dmanr, a);
+#endif
+
+ dma_device_address[dmanr] = a;
+}
+
+/*
+ * NOTE 2: "count" represents _bytes_.
+ *
+ * NOTE 3: While a 32-bit register, "count" is only a maximum 24-bit value.
+ */
+static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
+{
+ volatile unsigned int *dmalp;
+
+#ifdef DMA_DEBUG
+ printk("set_dma_count(dmanr=%d,count=%d)\n", dmanr, count);
+#endif
+
+ dmalp = (unsigned int *) dma_base_addr[dmanr];
+ dmalp[MCFDMA_DBCR] = count;
+}
+
+/*
+ * Get DMA residue count. After a DMA transfer, this
+ * should return zero. Reading this while a DMA transfer is
+ * still in progress will return unpredictable results.
+ * Otherwise, it returns the number of _bytes_ left to transfer.
+ */
+static __inline__ int get_dma_residue(unsigned int dmanr)
+{
+ volatile unsigned int *dmalp;
+ unsigned int count;
+
+#ifdef DMA_DEBUG
+ printk("get_dma_residue(dmanr=%d)\n", dmanr);
+#endif
+
+ dmalp = (unsigned int *) dma_base_addr[dmanr];
+ count = dmalp[MCFDMA_DBCR];
+ return(count);
+}
+
+#endif /* !defined(CONFIG_M5272) */
+#endif /* CONFIG_COLDFIRE */
+
+/* it's useless on the m68k, but unfortunately needed by the new
+ bootmem allocator (but this should do it for this) */
+#define MAX_DMA_ADDRESS PAGE_OFFSET
+
+#define MAX_DMA_CHANNELS 8
+
+extern int request_dma(unsigned int dmanr, const char * device_id); /* reserve a DMA channel */
+extern void free_dma(unsigned int dmanr); /* release it again */
+
+#define isa_dma_bridge_buggy (0)
+
+#endif /* _M68K_DMA_H */
+++ /dev/null
-#ifndef _M68K_DMA_H
-#define _M68K_DMA_H 1
-
-
-/* it's useless on the m68k, but unfortunately needed by the new
- bootmem allocator (but this should do it for this) */
-#define MAX_DMA_ADDRESS PAGE_OFFSET
-
-#define MAX_DMA_CHANNELS 8
-
-extern int request_dma(unsigned int dmanr, const char * device_id); /* reserve a DMA channel */
-extern void free_dma(unsigned int dmanr); /* release it again */
-
-#define isa_dma_bridge_buggy (0)
-
-#endif /* _M68K_DMA_H */
+++ /dev/null
-#ifndef _M68K_DMA_H
-#define _M68K_DMA_H 1
-
-//#define DMA_DEBUG 1
-
-
-#ifdef CONFIG_COLDFIRE
-/*
- * ColdFire DMA Model:
- * ColdFire DMA supports two forms of DMA: Single and Dual address. Single
- * address mode emits a source address, and expects that the device will either
- * pick up the data (DMA READ) or source data (DMA WRITE). This implies that
- * the device will place data on the correct byte(s) of the data bus, as the
- * memory transactions are always 32 bits. This implies that only 32 bit
- * devices will find single mode transfers useful. Dual address DMA mode
- * performs two cycles: source read and destination write. ColdFire will
- * align the data so that the device will always get the correct bytes, thus
- * is useful for 8 and 16 bit devices. This is the mode that is supported
- * below.
- *
- * AUG/22/2000 : added support for 32-bit Dual-Address-Mode (K) 2000
- * Oliver Kamphenkel (O.Kamphenkel@tu-bs.de)
- *
- * AUG/25/2000 : addad support for 8, 16 and 32-bit Single-Address-Mode (K)2000
- * Oliver Kamphenkel (O.Kamphenkel@tu-bs.de)
- *
- * APR/18/2002 : added proper support for MCF5272 DMA controller.
- * Arthur Shipkowski (art@videon-central.com)
- */
-
-#include <asm/coldfire.h>
-#include <asm/mcfsim.h>
-#include <asm/mcfdma.h>
-
-/*
- * Set number of channels of DMA on ColdFire for different implementations.
- */
-#if defined(CONFIG_M5249) || defined(CONFIG_M5307) || defined(CONFIG_M5407) || \
- defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x)
-#define MAX_M68K_DMA_CHANNELS 4
-#elif defined(CONFIG_M5272)
-#define MAX_M68K_DMA_CHANNELS 1
-#elif defined(CONFIG_M532x)
-#define MAX_M68K_DMA_CHANNELS 0
-#else
-#define MAX_M68K_DMA_CHANNELS 2
-#endif
-
-extern unsigned int dma_base_addr[MAX_M68K_DMA_CHANNELS];
-extern unsigned int dma_device_address[MAX_M68K_DMA_CHANNELS];
-
-#if !defined(CONFIG_M5272)
-#define DMA_MODE_WRITE_BIT 0x01 /* Memory/IO to IO/Memory select */
-#define DMA_MODE_WORD_BIT 0x02 /* 8 or 16 bit transfers */
-#define DMA_MODE_LONG_BIT 0x04 /* or 32 bit transfers */
-#define DMA_MODE_SINGLE_BIT 0x08 /* single-address-mode */
-
-/* I/O to memory, 8 bits, mode */
-#define DMA_MODE_READ 0
-/* memory to I/O, 8 bits, mode */
-#define DMA_MODE_WRITE 1
-/* I/O to memory, 16 bits, mode */
-#define DMA_MODE_READ_WORD 2
-/* memory to I/O, 16 bits, mode */
-#define DMA_MODE_WRITE_WORD 3
-/* I/O to memory, 32 bits, mode */
-#define DMA_MODE_READ_LONG 4
-/* memory to I/O, 32 bits, mode */
-#define DMA_MODE_WRITE_LONG 5
-/* I/O to memory, 8 bits, single-address-mode */
-#define DMA_MODE_READ_SINGLE 8
-/* memory to I/O, 8 bits, single-address-mode */
-#define DMA_MODE_WRITE_SINGLE 9
-/* I/O to memory, 16 bits, single-address-mode */
-#define DMA_MODE_READ_WORD_SINGLE 10
-/* memory to I/O, 16 bits, single-address-mode */
-#define DMA_MODE_WRITE_WORD_SINGLE 11
-/* I/O to memory, 32 bits, single-address-mode */
-#define DMA_MODE_READ_LONG_SINGLE 12
-/* memory to I/O, 32 bits, single-address-mode */
-#define DMA_MODE_WRITE_LONG_SINGLE 13
-
-#else /* CONFIG_M5272 is defined */
-
-/* Source static-address mode */
-#define DMA_MODE_SRC_SA_BIT 0x01
-/* Two bits to select between all four modes */
-#define DMA_MODE_SSIZE_MASK 0x06
-/* Offset to shift bits in */
-#define DMA_MODE_SSIZE_OFF 0x01
-/* Destination static-address mode */
-#define DMA_MODE_DES_SA_BIT 0x10
-/* Two bits to select between all four modes */
-#define DMA_MODE_DSIZE_MASK 0x60
-/* Offset to shift bits in */
-#define DMA_MODE_DSIZE_OFF 0x05
-/* Size modifiers */
-#define DMA_MODE_SIZE_LONG 0x00
-#define DMA_MODE_SIZE_BYTE 0x01
-#define DMA_MODE_SIZE_WORD 0x02
-#define DMA_MODE_SIZE_LINE 0x03
-
-/*
- * Aliases to help speed quick ports; these may be suboptimal, however. They
- * do not include the SINGLE mode modifiers since the MCF5272 does not have a
- * mode where the device is in control of its addressing.
- */
-
-/* I/O to memory, 8 bits, mode */
-#define DMA_MODE_READ ((DMA_MODE_SIZE_BYTE << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_BYTE << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT)
-/* memory to I/O, 8 bits, mode */
-#define DMA_MODE_WRITE ((DMA_MODE_SIZE_BYTE << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_BYTE << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT)
-/* I/O to memory, 16 bits, mode */
-#define DMA_MODE_READ_WORD ((DMA_MODE_SIZE_WORD << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_WORD << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT)
-/* memory to I/O, 16 bits, mode */
-#define DMA_MODE_WRITE_WORD ((DMA_MODE_SIZE_WORD << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_WORD << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT)
-/* I/O to memory, 32 bits, mode */
-#define DMA_MODE_READ_LONG ((DMA_MODE_SIZE_LONG << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_LONG << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT)
-/* memory to I/O, 32 bits, mode */
-#define DMA_MODE_WRITE_LONG ((DMA_MODE_SIZE_LONG << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_LONG << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT)
-
-#endif /* !defined(CONFIG_M5272) */
-
-#if !defined(CONFIG_M5272)
-/* enable/disable a specific DMA channel */
-static __inline__ void enable_dma(unsigned int dmanr)
-{
- volatile unsigned short *dmawp;
-
-#ifdef DMA_DEBUG
- printk("enable_dma(dmanr=%d)\n", dmanr);
-#endif
-
- dmawp = (unsigned short *) dma_base_addr[dmanr];
- dmawp[MCFDMA_DCR] |= MCFDMA_DCR_EEXT;
-}
-
-static __inline__ void disable_dma(unsigned int dmanr)
-{
- volatile unsigned short *dmawp;
- volatile unsigned char *dmapb;
-
-#ifdef DMA_DEBUG
- printk("disable_dma(dmanr=%d)\n", dmanr);
-#endif
-
- dmawp = (unsigned short *) dma_base_addr[dmanr];
- dmapb = (unsigned char *) dma_base_addr[dmanr];
-
- /* Turn off external requests, and stop any DMA in progress */
- dmawp[MCFDMA_DCR] &= ~MCFDMA_DCR_EEXT;
- dmapb[MCFDMA_DSR] = MCFDMA_DSR_DONE;
-}
-
-/*
- * Clear the 'DMA Pointer Flip Flop'.
- * Write 0 for LSB/MSB, 1 for MSB/LSB access.
- * Use this once to initialize the FF to a known state.
- * After that, keep track of it. :-)
- * --- In order to do that, the DMA routines below should ---
- * --- only be used while interrupts are disabled! ---
- *
- * This is a NOP for ColdFire. Provide a stub for compatibility.
- */
-static __inline__ void clear_dma_ff(unsigned int dmanr)
-{
-}
-
-/* set mode (above) for a specific DMA channel */
-static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
-{
-
- volatile unsigned char *dmabp;
- volatile unsigned short *dmawp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_mode(dmanr=%d,mode=%d)\n", dmanr, mode);
-#endif
-
- dmabp = (unsigned char *) dma_base_addr[dmanr];
- dmawp = (unsigned short *) dma_base_addr[dmanr];
-
- // Clear config errors
- dmabp[MCFDMA_DSR] = MCFDMA_DSR_DONE;
-
- // Set command register
- dmawp[MCFDMA_DCR] =
- MCFDMA_DCR_INT | // Enable completion irq
- MCFDMA_DCR_CS | // Force one xfer per request
- MCFDMA_DCR_AA | // Enable auto alignment
- // single-address-mode
- ((mode & DMA_MODE_SINGLE_BIT) ? MCFDMA_DCR_SAA : 0) |
- // sets s_rw (-> r/w) high if Memory to I/0
- ((mode & DMA_MODE_WRITE_BIT) ? MCFDMA_DCR_S_RW : 0) |
- // Memory to I/O or I/O to Memory
- ((mode & DMA_MODE_WRITE_BIT) ? MCFDMA_DCR_SINC : MCFDMA_DCR_DINC) |
- // 32 bit, 16 bit or 8 bit transfers
- ((mode & DMA_MODE_WORD_BIT) ? MCFDMA_DCR_SSIZE_WORD :
- ((mode & DMA_MODE_LONG_BIT) ? MCFDMA_DCR_SSIZE_LONG :
- MCFDMA_DCR_SSIZE_BYTE)) |
- ((mode & DMA_MODE_WORD_BIT) ? MCFDMA_DCR_DSIZE_WORD :
- ((mode & DMA_MODE_LONG_BIT) ? MCFDMA_DCR_DSIZE_LONG :
- MCFDMA_DCR_DSIZE_BYTE));
-
-#ifdef DEBUG_DMA
- printk("%s(%d): dmanr=%d DSR[%x]=%x DCR[%x]=%x\n", __FILE__, __LINE__,
- dmanr, (int) &dmabp[MCFDMA_DSR], dmabp[MCFDMA_DSR],
- (int) &dmawp[MCFDMA_DCR], dmawp[MCFDMA_DCR]);
-#endif
-}
-
-/* Set transfer address for specific DMA channel */
-static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
-{
- volatile unsigned short *dmawp;
- volatile unsigned int *dmalp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_addr(dmanr=%d,a=%x)\n", dmanr, a);
-#endif
-
- dmawp = (unsigned short *) dma_base_addr[dmanr];
- dmalp = (unsigned int *) dma_base_addr[dmanr];
-
- // Determine which address registers are used for memory/device accesses
- if (dmawp[MCFDMA_DCR] & MCFDMA_DCR_SINC) {
- // Source incrementing, must be memory
- dmalp[MCFDMA_SAR] = a;
- // Set dest address, must be device
- dmalp[MCFDMA_DAR] = dma_device_address[dmanr];
- } else {
- // Destination incrementing, must be memory
- dmalp[MCFDMA_DAR] = a;
- // Set source address, must be device
- dmalp[MCFDMA_SAR] = dma_device_address[dmanr];
- }
-
-#ifdef DEBUG_DMA
- printk("%s(%d): dmanr=%d DCR[%x]=%x SAR[%x]=%08x DAR[%x]=%08x\n",
- __FILE__, __LINE__, dmanr, (int) &dmawp[MCFDMA_DCR], dmawp[MCFDMA_DCR],
- (int) &dmalp[MCFDMA_SAR], dmalp[MCFDMA_SAR],
- (int) &dmalp[MCFDMA_DAR], dmalp[MCFDMA_DAR]);
-#endif
-}
-
-/*
- * Specific for Coldfire - sets device address.
- * Should be called after the mode set call, and before set DMA address.
- */
-static __inline__ void set_dma_device_addr(unsigned int dmanr, unsigned int a)
-{
-#ifdef DMA_DEBUG
- printk("set_dma_device_addr(dmanr=%d,a=%x)\n", dmanr, a);
-#endif
-
- dma_device_address[dmanr] = a;
-}
-
-/*
- * NOTE 2: "count" represents _bytes_.
- */
-static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
-{
- volatile unsigned short *dmawp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_count(dmanr=%d,count=%d)\n", dmanr, count);
-#endif
-
- dmawp = (unsigned short *) dma_base_addr[dmanr];
- dmawp[MCFDMA_BCR] = (unsigned short)count;
-}
-
-/*
- * Get DMA residue count. After a DMA transfer, this
- * should return zero. Reading this while a DMA transfer is
- * still in progress will return unpredictable results.
- * Otherwise, it returns the number of _bytes_ left to transfer.
- */
-static __inline__ int get_dma_residue(unsigned int dmanr)
-{
- volatile unsigned short *dmawp;
- unsigned short count;
-
-#ifdef DMA_DEBUG
- printk("get_dma_residue(dmanr=%d)\n", dmanr);
-#endif
-
- dmawp = (unsigned short *) dma_base_addr[dmanr];
- count = dmawp[MCFDMA_BCR];
- return((int) count);
-}
-#else /* CONFIG_M5272 is defined */
-
-/*
- * The MCF5272 DMA controller is very different than the controller defined above
- * in terms of register mapping. For instance, with the exception of the 16-bit
- * interrupt register (IRQ#85, for reference), all of the registers are 32-bit.
- *
- * The big difference, however, is the lack of device-requested DMA. All modes
- * are dual address transfer, and there is no 'device' setup or direction bit.
- * You can DMA between a device and memory, between memory and memory, or even between
- * two devices directly, with any combination of incrementing and non-incrementing
- * addresses you choose. This puts a crimp in distinguishing between the 'device
- * address' set up by set_dma_device_addr.
- *
- * Therefore, there are two options. One is to use set_dma_addr and set_dma_device_addr,
- * which will act exactly as above in -- it will look to see if the source is set to
- * autoincrement, and if so it will make the source use the set_dma_addr value and the
- * destination the set_dma_device_addr value. Otherwise the source will be set to the
- * set_dma_device_addr value and the destination will get the set_dma_addr value.
- *
- * The other is to use the provided set_dma_src_addr and set_dma_dest_addr functions
- * and make it explicit. Depending on what you're doing, one of these two should work
- * for you, but don't mix them in the same transfer setup.
- */
-
-/* enable/disable a specific DMA channel */
-static __inline__ void enable_dma(unsigned int dmanr)
-{
- volatile unsigned int *dmalp;
-
-#ifdef DMA_DEBUG
- printk("enable_dma(dmanr=%d)\n", dmanr);
-#endif
-
- dmalp = (unsigned int *) dma_base_addr[dmanr];
- dmalp[MCFDMA_DMR] |= MCFDMA_DMR_EN;
-}
-
-static __inline__ void disable_dma(unsigned int dmanr)
-{
- volatile unsigned int *dmalp;
-
-#ifdef DMA_DEBUG
- printk("disable_dma(dmanr=%d)\n", dmanr);
-#endif
-
- dmalp = (unsigned int *) dma_base_addr[dmanr];
-
- /* Turn off external requests, and stop any DMA in progress */
- dmalp[MCFDMA_DMR] &= ~MCFDMA_DMR_EN;
- dmalp[MCFDMA_DMR] |= MCFDMA_DMR_RESET;
-}
-
-/*
- * Clear the 'DMA Pointer Flip Flop'.
- * Write 0 for LSB/MSB, 1 for MSB/LSB access.
- * Use this once to initialize the FF to a known state.
- * After that, keep track of it. :-)
- * --- In order to do that, the DMA routines below should ---
- * --- only be used while interrupts are disabled! ---
- *
- * This is a NOP for ColdFire. Provide a stub for compatibility.
- */
-static __inline__ void clear_dma_ff(unsigned int dmanr)
-{
-}
-
-/* set mode (above) for a specific DMA channel */
-static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
-{
-
- volatile unsigned int *dmalp;
- volatile unsigned short *dmawp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_mode(dmanr=%d,mode=%d)\n", dmanr, mode);
-#endif
- dmalp = (unsigned int *) dma_base_addr[dmanr];
- dmawp = (unsigned short *) dma_base_addr[dmanr];
-
- // Clear config errors
- dmalp[MCFDMA_DMR] |= MCFDMA_DMR_RESET;
-
- // Set command register
- dmalp[MCFDMA_DMR] =
- MCFDMA_DMR_RQM_DUAL | // Mandatory Request Mode setting
- MCFDMA_DMR_DSTT_SD | // Set up addressing types; set to supervisor-data.
- MCFDMA_DMR_SRCT_SD | // Set up addressing types; set to supervisor-data.
- // source static-address-mode
- ((mode & DMA_MODE_SRC_SA_BIT) ? MCFDMA_DMR_SRCM_SA : MCFDMA_DMR_SRCM_IA) |
- // dest static-address-mode
- ((mode & DMA_MODE_DES_SA_BIT) ? MCFDMA_DMR_DSTM_SA : MCFDMA_DMR_DSTM_IA) |
- // burst, 32 bit, 16 bit or 8 bit transfers are separately configurable on the MCF5272
- (((mode & DMA_MODE_SSIZE_MASK) >> DMA_MODE_SSIZE_OFF) << MCFDMA_DMR_DSTS_OFF) |
- (((mode & DMA_MODE_SSIZE_MASK) >> DMA_MODE_SSIZE_OFF) << MCFDMA_DMR_SRCS_OFF);
-
- dmawp[MCFDMA_DIR] |= MCFDMA_DIR_ASCEN; /* Enable completion interrupts */
-
-#ifdef DEBUG_DMA
- printk("%s(%d): dmanr=%d DMR[%x]=%x DIR[%x]=%x\n", __FILE__, __LINE__,
- dmanr, (int) &dmalp[MCFDMA_DMR], dmabp[MCFDMA_DMR],
- (int) &dmawp[MCFDMA_DIR], dmawp[MCFDMA_DIR]);
-#endif
-}
-
-/* Set transfer address for specific DMA channel */
-static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
-{
- volatile unsigned int *dmalp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_addr(dmanr=%d,a=%x)\n", dmanr, a);
-#endif
-
- dmalp = (unsigned int *) dma_base_addr[dmanr];
-
- // Determine which address registers are used for memory/device accesses
- if (dmalp[MCFDMA_DMR] & MCFDMA_DMR_SRCM) {
- // Source incrementing, must be memory
- dmalp[MCFDMA_DSAR] = a;
- // Set dest address, must be device
- dmalp[MCFDMA_DDAR] = dma_device_address[dmanr];
- } else {
- // Destination incrementing, must be memory
- dmalp[MCFDMA_DDAR] = a;
- // Set source address, must be device
- dmalp[MCFDMA_DSAR] = dma_device_address[dmanr];
- }
-
-#ifdef DEBUG_DMA
- printk("%s(%d): dmanr=%d DMR[%x]=%x SAR[%x]=%08x DAR[%x]=%08x\n",
- __FILE__, __LINE__, dmanr, (int) &dmawp[MCFDMA_DMR], dmawp[MCFDMA_DMR],
- (int) &dmalp[MCFDMA_DSAR], dmalp[MCFDMA_DSAR],
- (int) &dmalp[MCFDMA_DDAR], dmalp[MCFDMA_DDAR]);
-#endif
-}
-
-/*
- * Specific for Coldfire - sets device address.
- * Should be called after the mode set call, and before set DMA address.
- */
-static __inline__ void set_dma_device_addr(unsigned int dmanr, unsigned int a)
-{
-#ifdef DMA_DEBUG
- printk("set_dma_device_addr(dmanr=%d,a=%x)\n", dmanr, a);
-#endif
-
- dma_device_address[dmanr] = a;
-}
-
-/*
- * NOTE 2: "count" represents _bytes_.
- *
- * NOTE 3: While a 32-bit register, "count" is only a maximum 24-bit value.
- */
-static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
-{
- volatile unsigned int *dmalp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_count(dmanr=%d,count=%d)\n", dmanr, count);
-#endif
-
- dmalp = (unsigned int *) dma_base_addr[dmanr];
- dmalp[MCFDMA_DBCR] = count;
-}
-
-/*
- * Get DMA residue count. After a DMA transfer, this
- * should return zero. Reading this while a DMA transfer is
- * still in progress will return unpredictable results.
- * Otherwise, it returns the number of _bytes_ left to transfer.
- */
-static __inline__ int get_dma_residue(unsigned int dmanr)
-{
- volatile unsigned int *dmalp;
- unsigned int count;
-
-#ifdef DMA_DEBUG
- printk("get_dma_residue(dmanr=%d)\n", dmanr);
-#endif
-
- dmalp = (unsigned int *) dma_base_addr[dmanr];
- count = dmalp[MCFDMA_DBCR];
- return(count);
-}
-
-#endif /* !defined(CONFIG_M5272) */
-#endif /* CONFIG_COLDFIRE */
-
-#define MAX_DMA_CHANNELS 8
-
-/* Don't define MAX_DMA_ADDRESS; it's useless on the m68k/coldfire and any
- occurrence should be flagged as an error. */
-/* under 2.4 it is actually needed by the new bootmem allocator */
-#define MAX_DMA_ADDRESS PAGE_OFFSET
-
-/* These are in kernel/dma.c: */
-extern int request_dma(unsigned int dmanr, const char *device_id); /* reserve a DMA channel */
-extern void free_dma(unsigned int dmanr); /* release it again */
-
-#endif /* _M68K_DMA_H */
projects / openwrt / staging / blogic.git / commitdiff