bnx2x: convert to net_device_ops

Convert driver to new net_device_ops. Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c
index 49f8e7891626e9f906a2532b3502328796bc81af..a9c4de0d202008c5b438de13c6f28c5fd51d5d68 100644 (file)
--- a/drivers/net/bnx2x_main.c
+++ b/drivers/net/bnx2x_main.c
@@ -10002,6 +10002,25 @@ static void poll_bnx2x(struct net_device *dev)
 }
 #endif
 
+static const struct net_device_ops bnx2x_netdev_ops = {
+       .ndo_open               = bnx2x_open,
+       .ndo_stop               = bnx2x_close,
+       .ndo_start_xmit         = bnx2x_start_xmit,
+       .ndo_set_multicast_list = bnx2x_set_rx_mode,
+       .ndo_set_mac_address    = bnx2x_change_mac_addr,
+       .ndo_validate_addr      = eth_validate_addr,
+       .ndo_do_ioctl           = bnx2x_ioctl,
+       .ndo_change_mtu         = bnx2x_change_mtu,
+       .ndo_tx_timeout         = bnx2x_tx_timeout,
+#ifdef BCM_VLAN
+       .ndo_vlan_rx_register   = bnx2x_vlan_rx_register,
+#endif
+#if defined(HAVE_POLL_CONTROLLER) || defined(CONFIG_NET_POLL_CONTROLLER)
+       .ndo_poll_controller    = poll_bnx2x,
+#endif
+};
+
+
 static int __devinit bnx2x_init_dev(struct pci_dev *pdev,
                                    struct net_device *dev)
 {
@@ -10112,23 +10131,10 @@ static int __devinit bnx2x_init_dev(struct pci_dev *pdev,
        REG_WR(bp, PXP2_REG_PGL_ADDR_90_F0 + BP_PORT(bp)*16, 0);
        REG_WR(bp, PXP2_REG_PGL_ADDR_94_F0 + BP_PORT(bp)*16, 0);
 
-       dev->hard_start_xmit = bnx2x_start_xmit;
        dev->watchdog_timeo = TX_TIMEOUT;
 
+       dev->netdev_ops = &bnx2x_netdev_ops;
        dev->ethtool_ops = &bnx2x_ethtool_ops;
-       dev->open = bnx2x_open;
-       dev->stop = bnx2x_close;
-       dev->set_multicast_list = bnx2x_set_rx_mode;
-       dev->set_mac_address = bnx2x_change_mac_addr;
-       dev->do_ioctl = bnx2x_ioctl;
-       dev->change_mtu = bnx2x_change_mtu;
-       dev->tx_timeout = bnx2x_tx_timeout;
-#ifdef BCM_VLAN
-       dev->vlan_rx_register = bnx2x_vlan_rx_register;
-#endif
-#if defined(HAVE_POLL_CONTROLLER) || defined(CONFIG_NET_POLL_CONTROLLER)
-       dev->poll_controller = poll_bnx2x;
-#endif
        dev->features |= NETIF_F_SG;
        dev->features |= NETIF_F_HW_CSUM;
        if (bp->flags & USING_DAC_FLAG)