==================
Supported chips:
+ * IT8603E
+ Prefix: 'it8603'
+ Addresses scanned: from Super I/O config space (8 I/O ports)
+ Datasheet: Not publicly available
* IT8705F
Prefix: 'it87'
Addresses scanned: from Super I/O config space (8 I/O ports)
Description
-----------
-This driver implements support for the IT8705F, IT8712F, IT8716F,
+This driver implements support for the IT8603E, IT8705F, IT8712F, IT8716F,
IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E, IT8771E, IT8772E,
IT8782F, IT8783E/F, and SiS950 chips.
The IT8728F, IT8771E, and IT8772E are considered compatible with the IT8721F,
until a datasheet becomes available (hopefully.)
+The IT8603E is a custom design, hardware monitoring part is similar to
+IT8728F. It only supports 16-bit fan mode, the full speed mode of the
+fan is not supported (value 0 of pwmX_enable).
+
Temperatures are measured in degrees Celsius. An alarm is triggered once
when the Overtemperature Shutdown limit is crossed.
maximum limit. Note that minimum in this case always means 'closest to
zero'; this is important for negative voltage measurements. All voltage
inputs can measure voltages between 0 and 4.08 volts, with a resolution of
-0.016 volt (except IT8721F/IT8758E and IT8728F: 0.012 volt.) The battery
-voltage in8 does not have limit registers.
-
-On the IT8721F/IT8758E, IT8782F, and IT8783E/F, some voltage inputs are
-internal and scaled inside the chip (in7 (optional for IT8782F and IT8783E/F),
-in8 and optionally in3). The driver handles this transparently so user-space
-doesn't have to care.
+0.016 volt (except IT8603E, IT8721F/IT8758E and IT8728F: 0.012 volt.) The
+battery voltage in8 does not have limit registers.
+
+On the IT8603E, IT8721F/IT8758E, IT8782F, and IT8783E/F, some voltage inputs
+are internal and scaled inside the chip:
+* in3 (optional)
+* in7 (optional for IT8782F and IT8783E/F)
+* in8 (always)
+* in9 (relevant for IT8603E only)
+The driver handles this transparently so user-space doesn't have to care.
The VID lines (IT8712F/IT8716F/IT8718F/IT8720F) encode the core voltage value:
the voltage level your processor should work with. This is hardcoded by
* This driver supports only the Environment Controller in the IT8705F and
* similar parts. The other devices are supported by different drivers.
*
- * Supports: IT8705F Super I/O chip w/LPC interface
+ * Supports: IT8603E Super I/O chip w/LPC interface
+ * IT8705F Super I/O chip w/LPC interface
* IT8712F Super I/O chip w/LPC interface
* IT8716F Super I/O chip w/LPC interface
* IT8718F Super I/O chip w/LPC interface
#define DRVNAME "it87"
enum chips { it87, it8712, it8716, it8718, it8720, it8721, it8728, it8771,
- it8772, it8782, it8783 };
+ it8772, it8782, it8783, it8603 };
static unsigned short force_id;
module_param(force_id, ushort, 0);
#define IT8772E_DEVID 0x8772
#define IT8782F_DEVID 0x8782
#define IT8783E_DEVID 0x8783
+#define IT8306E_DEVID 0x8603
#define IT87_ACT_REG 0x30
#define IT87_BASE_REG 0x60
| FEAT_TEMP_OLD_PECI,
.old_peci_mask = 0x4,
},
+ [it8603] = {
+ .name = "it8603",
+ .features = FEAT_NEWER_AUTOPWM | FEAT_12MV_ADC | FEAT_16BIT_FANS
+ | FEAT_TEMP_OFFSET | FEAT_TEMP_PECI,
+ .peci_mask = 0x07,
+ },
};
#define has_16bit_fans(data) ((data)->features & FEAT_16BIT_FANS)
unsigned long last_updated; /* In jiffies */
u16 in_scaled; /* Internal voltage sensors are scaled */
- u8 in[9][3]; /* [nr][0]=in, [1]=min, [2]=max */
+ u8 in[10][3]; /* [nr][0]=in, [1]=min, [2]=max */
u8 has_fan; /* Bitfield, fans enabled */
u16 fan[5][2]; /* Register values, [nr][0]=fan, [1]=min */
u8 has_temp; /* Bitfield, temp sensors enabled */
7, 2);
static SENSOR_DEVICE_ATTR_2(in8_input, S_IRUGO, show_in, NULL, 8, 0);
+static SENSOR_DEVICE_ATTR_2(in9_input, S_IRUGO, show_in, NULL, 9, 0);
/* 3 temperatures */
static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
{
int ctrl = data->fan_main_ctrl & (1 << nr);
- if (ctrl == 0) /* Full speed */
+ if (ctrl == 0 && data->type != it8603) /* Full speed */
return 0;
if (data->pwm_ctrl[nr] & 0x80) /* Automatic mode */
return 2;
return -EINVAL;
}
+ /* IT8603E does not have on/off mode */
+ if (val == 0 && data->type == it8603)
+ return -EINVAL;
+
mutex_lock(&data->update_lock);
if (val == 0) {
else /* Automatic mode */
data->pwm_ctrl[nr] = 0x80 | data->pwm_temp_map[nr];
it87_write_value(data, IT87_REG_PWM(nr), data->pwm_ctrl[nr]);
- /* set SmartGuardian mode */
- data->fan_main_ctrl |= (1 << nr);
- it87_write_value(data, IT87_REG_FAN_MAIN_CTRL,
- data->fan_main_ctrl);
+
+ if (data->type != it8603) {
+ /* set SmartGuardian mode */
+ data->fan_main_ctrl |= (1 << nr);
+ it87_write_value(data, IT87_REG_FAN_MAIN_CTRL,
+ data->fan_main_ctrl);
+ }
}
mutex_unlock(&data->update_lock);
static SENSOR_DEVICE_ATTR(in3_label, S_IRUGO, show_label, NULL, 0);
static SENSOR_DEVICE_ATTR(in7_label, S_IRUGO, show_label, NULL, 1);
static SENSOR_DEVICE_ATTR(in8_label, S_IRUGO, show_label, NULL, 2);
+/* special AVCC3 IT8306E in9 */
+static SENSOR_DEVICE_ATTR(in9_label, S_IRUGO, show_label, NULL, 0);
static ssize_t show_name(struct device *dev, struct device_attribute
*devattr, char *buf)
}
static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
-static struct attribute *it87_attributes_in[9][5] = {
+static struct attribute *it87_attributes_in[10][5] = {
{
&sensor_dev_attr_in0_input.dev_attr.attr,
&sensor_dev_attr_in0_min.dev_attr.attr,
}, {
&sensor_dev_attr_in8_input.dev_attr.attr,
NULL
+}, {
+ &sensor_dev_attr_in9_input.dev_attr.attr,
+ NULL
} };
-static const struct attribute_group it87_group_in[9] = {
+static const struct attribute_group it87_group_in[10] = {
{ .attrs = it87_attributes_in[0] },
{ .attrs = it87_attributes_in[1] },
{ .attrs = it87_attributes_in[2] },
{ .attrs = it87_attributes_in[6] },
{ .attrs = it87_attributes_in[7] },
{ .attrs = it87_attributes_in[8] },
+ { .attrs = it87_attributes_in[9] },
};
static struct attribute *it87_attributes_temp[3][6] = {
&sensor_dev_attr_in5_beep.dev_attr.attr,
&sensor_dev_attr_in6_beep.dev_attr.attr,
&sensor_dev_attr_in7_beep.dev_attr.attr,
- NULL
+ NULL,
+ NULL,
};
static struct attribute *it87_attributes_temp_beep[] = {
&sensor_dev_attr_in3_label.dev_attr.attr,
&sensor_dev_attr_in7_label.dev_attr.attr,
&sensor_dev_attr_in8_label.dev_attr.attr,
+ &sensor_dev_attr_in9_label.dev_attr.attr,
NULL
};
case IT8783E_DEVID:
sio_data->type = it8783;
break;
+ case IT8306E_DEVID:
+ sio_data->type = it8603;
+ break;
case 0xffff: /* No device at all */
goto exit;
default:
err = 0;
sio_data->revision = superio_inb(DEVREV) & 0x0f;
- pr_info("Found IT%04xF chip at 0x%x, revision %d\n",
- chip_type, *address, sio_data->revision);
+ pr_info("Found IT%04x%c chip at 0x%x, revision %d\n", chip_type,
+ chip_type == 0x8603 ? 'E' : 'F', *address,
+ sio_data->revision);
/* in8 (Vbat) is always internal */
sio_data->internal = (1 << 2);
+ /* Only the IT8603E has in9 */
+ if (sio_data->type != it8603)
+ sio_data->skip_in |= (1 << 9);
/* Read GPIO config and VID value from LDN 7 (GPIO) */
if (sio_data->type == it87) {
sio_data->internal |= (1 << 1);
sio_data->beep_pin = superio_inb(IT87_SIO_BEEP_PIN_REG) & 0x3f;
+ } else if (sio_data->type == it8603) {
+ int reg27, reg29;
+
+ sio_data->skip_vid = 1; /* No VID */
+ superio_select(GPIO);
+ reg27 = superio_inb(IT87_SIO_GPIO3_REG);
+
+ /* Check if fan3 is there or not */
+ if (reg27 & (1 << 6))
+ sio_data->skip_pwm |= (1 << 2);
+ if (reg27 & (1 << 7))
+ sio_data->skip_fan |= (1 << 2);
+
+ /* Check if fan2 is there or not */
+ reg29 = superio_inb(IT87_SIO_GPIO5_REG);
+ if (reg29 & (1 << 1))
+ sio_data->skip_pwm |= (1 << 1);
+ if (reg29 & (1 << 2))
+ sio_data->skip_fan |= (1 << 1);
+
+ sio_data->skip_in |= (1 << 5); /* No VIN5 */
+ sio_data->skip_in |= (1 << 6); /* No VIN6 */
+
+ /* no fan4 */
+ sio_data->skip_pwm |= (1 << 3);
+ sio_data->skip_fan |= (1 << 3);
+
+ sio_data->internal |= (1 << 1); /* in7 is VSB */
+ sio_data->internal |= (1 << 3); /* in9 is AVCC */
+
+ sio_data->beep_pin = superio_inb(IT87_SIO_BEEP_PIN_REG) & 0x3f;
} else {
int reg;
bool uart6;
int i;
sysfs_remove_group(&dev->kobj, &it87_group);
- for (i = 0; i < 9; i++) {
+ for (i = 0; i < 10; i++) {
if (sio_data->skip_in & (1 << i))
continue;
sysfs_remove_group(&dev->kobj, &it87_group_in[i]);
data->in_scaled |= (1 << 7); /* in7 is VSB */
if (sio_data->internal & (1 << 2))
data->in_scaled |= (1 << 8); /* in8 is Vbat */
+ if (sio_data->internal & (1 << 3))
+ data->in_scaled |= (1 << 9); /* in9 is AVCC */
} else if (sio_data->type == it8782 || sio_data->type == it8783) {
if (sio_data->internal & (1 << 0))
data->in_scaled |= (1 << 3); /* in3 is VCC5V */
if (err)
return err;
- for (i = 0; i < 9; i++) {
+ for (i = 0; i < 10; i++) {
if (sio_data->skip_in & (1 << i))
continue;
err = sysfs_create_group(&dev->kobj, &it87_group_in[i]);
}
/* Export labels for internal sensors */
- for (i = 0; i < 3; i++) {
+ for (i = 0; i < 4; i++) {
if (!(sio_data->internal & (1 << i)))
continue;
err = sysfs_create_file(&dev->kobj,
}
data->has_fan = (data->fan_main_ctrl >> 4) & 0x07;
- /* Set tachometers to 16-bit mode if needed */
- if (has_16bit_fans(data)) {
+ /* Set tachometers to 16-bit mode if needed, IT8603E (and IT8728F?)
+ * has it by default */
+ if (has_16bit_fans(data) && data->type != it8603) {
tmp = it87_read_value(data, IT87_REG_FAN_16BIT);
if (~tmp & 0x07 & data->has_fan) {
dev_dbg(&pdev->dev,
}
/* in8 (battery) has no limit registers */
data->in[8][0] = it87_read_value(data, IT87_REG_VIN(8));
+ if (data->type == it8603)
+ data->in[9][0] = it87_read_value(data, 0x2f);
for (i = 0; i < 5; i++) {
/* Skip disabled fans */