Technicolor TG582n Telecom Italia branded a.k.a.
Telecom Italia ADSL2+ Wi-Fi N (AGTWI)
has the same PCB as the unbranded Technicolor TG582n with LEDs
connected to different GPIO PINs in active low configuration and
different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one.
Hardware:
* Board ID: DANT-V
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H
* Serial flash: 16 Mbyte - Spansion FL 128SAIF00
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
PCB: |GPIO: |TG582n: |AGTWI:
LED2R |488(08) |red Power |red Power
LED2G |484(04) |green Power |green Power
LED10R |486(06) | |missing R85 end LED
LED13G |485(05) |green Ethernet |green ADSL
LED11R |494(14) | |red Internet
LED14G |491(11) |green Broadband |green Internet
LED5R |487(07) |red Internet |red Wi-Fi
LED5G |481(01) |green Internet |green Wi-Fi
LED12R |498(18) | |red Service
LED12G |499(19) | |green Service
LED6R |482(02) |red Wi-Fi |missing R108 end LED
LED6G |483(03) |green Wi-Fi |missing R107 end LED
LED7R |490(10) |red WPS |missing R91 end LED
LED7G |489(09) |green WPS |missing R92 end LED
LED4 |508(28) |ethernet port 4 |ethernet port 4
LED3 |507(27) |ethernet port 3 |ethernet port 3
LED9 |506(26) |ethernet port 2 |ethernet port 2
LED8 |505(25) |ethernet port 1 |ethernet port 1
SW3 |503(23) |key Reset |key Reset
SW5 |504(24) |key WPS |key Wi-Fi/LED
SW4 |495(15) |key Wi-Fi |missing R127 end key
SW6 |493(13) | |missing R171 end key
SW1 |492(12) | |missing R1 end key
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[DT fixes, base-files fixes and device variant]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
sercomm,h500-s-vfes)
ucidef_set_led_netdev "wan" "WAN" "green:internet" "eth0.2"
;;
+technicolor,tg582n-telecom-italia)
+ ucidef_set_led_netdev "wlan0" "WIFI" "green:wifi" "wlan0"
+ ucidef_set_led_usbdev "usb1" "USB1" "green:service" "1-1"
+ ucidef_set_led_usbdev "usb2" "USB2" "red:service" "2-1"
+ ;;
telsey,cpva502plus)
ucidef_set_led_netdev "lan" "LAN" "amber:link" "eth0"
;;
nucom,r5010un-v2|\
sagem,fast-2504n|\
sagem,fast-2704-v2|\
+technicolor,tg582n-telecom-italia|\
zyxel,p870hw-51a-v2)
ucidef_add_switch "switch0" \
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "8t@eth0"
nucom,r5010un-v2|\
observa,vh4032n|\
t-com,speedport-w-303v|\
+ technicolor,tg582n-telecom-italia|\
telsey,cpva502plus|\
telsey,cpva642|\
telsey,magic|\
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "bcm6328.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Technicolor TG582n Telecom Italia";
+ compatible = "technicolor,tg582n-telecom-italia", "brcm,bcm6328";
+
+ aliases {
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_green;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_green;
+ };
+
+ chosen {
+ bootargs = "rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200";
+ stdout-path = "serial0:115200n8";
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&pinctrl 23 1>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&pinctrl 24 1>;
+ linux,code = <KEY_WPS_BUTTON>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&leds {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led@1 {
+ reg = <1>;
+ active-low;
+ label = "green:wifi";
+ };
+
+ led_power_green: led@4 {
+ reg = <4>;
+ active-low;
+ label = "green:power";
+ default-state = "on";
+ };
+
+ led@5 {
+ reg = <5>;
+ active-low;
+ label = "green:adsl";
+ };
+
+ led@7 {
+ reg = <7>;
+ active-low;
+ label = "red:wifi";
+ };
+
+ led@8 {
+ reg = <8>;
+ active-low;
+ label = "red:power";
+ };
+
+ led@11 {
+ reg = <11>;
+ active-low;
+ label = "green:internet";
+ };
+
+ led@14 {
+ reg = <14>;
+ active-low;
+ label = "red:internet";
+ };
+
+ led@18 {
+ reg = <18>;
+ active-low;
+ label = "red:service";
+ };
+
+ led@19 {
+ reg = <19>;
+ active-low;
+ label = "green:service";
+ };
+};
+
+&hsspi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <16666667>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
+ reg = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ reg = <0x000000 0x010000>;
+ label = "cfe";
+ read-only;
+ };
+
+ partition@10000 {
+ reg = <0x010000 0xff0000>;
+ label = "linux";
+ compatible = "brcm,bcm963xx-imagetag";
+ };
+ };
+ };
+};
+
+&pinctrl {
+ pinctrl_leds: leds {
+ function = "led";
+ pins = "gpio1", "gpio4",
+ "gpio5", "gpio7",
+ "gpio8", "gpio11",
+ "gpio14", "gpio18",
+ "gpio19";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
endef
TARGET_DEVICES += t-com_speedport-w-500v
+### Technicolor ###
+define Device/technicolor_tg582n-telecom-italia
+ $(Device/bcm63xx)
+ DEVICE_VENDOR := Technicolor
+ DEVICE_MODEL := TG582n
+ DEVICE_VARIANT := Telecom Italia
+ IMAGES += sysupgrade.bin
+ CFE_BOARD_ID := DANT-V
+ CHIP_ID := 6328
+ FLASH_MB := 16
+ DEVICE_PACKAGES := $(USB2_PACKAGES) $(B43_PACKAGES)
+endef
+TARGET_DEVICES += technicolor_tg582n-telecom-italia
+
### Tecom ###
define Device/tecom_gw6000
$(Device/bcm63xx-legacy)
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -348,6 +348,525 @@ static struct board_info __initdata boar
+@@ -348,6 +348,568 @@ static struct board_info __initdata boar
},
},
};
+ .pci_bus = 1,
+ .pci_dev = 0,
+ },
++};
++
++static struct board_info __initdata board_TG582N_TELECOM_ITALIA = {
++ .name = "DANT-V",
++ .expected_cpu_id = 0x6328,
++
++ .has_pci = 1,
++ .has_ohci0 = 1,
++ .has_ehci0 = 1,
++ .num_usbh_ports = 1,
++
++ .has_enetsw = 1,
++ .enetsw = {
++ .used_ports = {
++ [0] = {
++ .used = 1,
++ .phy_id = 1,
++ .name = "Port 1",
++ },
++ [1] = {
++ .used = 1,
++ .phy_id = 2,
++ .name = "Port 2",
++ },
++ [2] = {
++ .used = 1,
++ .phy_id = 3,
++ .name = "Port 3",
++ },
++ [3] = {
++ .used = 1,
++ .phy_id = 4,
++ .name = "Port 4",
++ },
++ },
++ },
++
++ .use_fallback_sprom = 1,
++ .fallback_sprom = {
++ .type = SPROM_BCM43225,
++ .pci_bus = 1,
++ .pci_dev = 0,
++ },
+};
#endif /* CONFIG_BCM63XX_CPU_6328 */
/*
-@@ -703,6 +1222,17 @@ static const struct board_info __initcon
+@@ -703,6 +1265,18 @@ static const struct board_info __initcon
#endif /* CONFIG_BCM63XX_CPU_6318 */
#ifdef CONFIG_BCM63XX_CPU_6328
&board_96328avng,
+ &board_FAST2704V2,
+ &board_PDG_A4001N_A_000_1A1_AX,
+ &board_PDG_A4101N_A_000_1A1_AE,
++ &board_TG582N_TELECOM_ITALIA,
+ &board_R5010UNV2,
#endif /* CONFIG_BCM63XX_CPU_6328 */
#ifdef CONFIG_BCM63XX_CPU_6338
&board_96338gw,
-@@ -742,7 +1272,20 @@ static struct of_device_id const bcm963x
+@@ -742,7 +1316,21 @@ static struct of_device_id const bcm963x
{ .compatible = "sagem,fast-2704n", .data = &board_FAST2704N, },
#endif /* CONFIG_BCM63XX_CPU_6318 */
#ifdef CONFIG_BCM63XX_CPU_6328
+ { .compatible = "sagem,fast-2704-v2", .data = &board_FAST2704V2, },
+ { .compatible = "sercomm,ad1018", .data = &board_AD1018, },
+ { .compatible = "sercomm,ad1018-nor", .data = &board_AD1018, },
++ { .compatible = "technicolor,tg582n-telecom-italia", .data = &board_TG582N_TELECOM_ITALIA, },
#endif /* CONFIG_BCM63XX_CPU_6328 */
#ifdef CONFIG_BCM63XX_CPU_6338
{ .compatible = "brcm,bcm96338gw", .data = &board_96338gw, },
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -900,6 +900,32 @@ static struct board_info __initdata boar
+@@ -943,6 +943,32 @@ static struct board_info __initdata boar
.force_duplex_full = 1,
},
};
#endif /* CONFIG_BCM63XX_CPU_6338 */
/*
-@@ -1237,6 +1263,8 @@ static const struct board_info __initcon
+@@ -1281,6 +1307,8 @@ static const struct board_info __initcon
#ifdef CONFIG_BCM63XX_CPU_6338
&board_96338gw,
&board_96338w,
#endif /* CONFIG_BCM63XX_CPU_6338 */
#ifdef CONFIG_BCM63XX_CPU_6345
&board_96345gw2,
-@@ -1290,6 +1318,8 @@ static struct of_device_id const bcm963x
+@@ -1335,6 +1363,8 @@ static struct of_device_id const bcm963x
#ifdef CONFIG_BCM63XX_CPU_6338
{ .compatible = "brcm,bcm96338gw", .data = &board_96338gw, },
{ .compatible = "brcm,bcm96338w", .data = &board_96338w, },
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -936,6 +936,19 @@ static struct board_info __initdata boar
+@@ -979,6 +979,19 @@ static struct board_info __initdata boar
.name = "96345GW2",
.expected_cpu_id = 0x6345,
};
#endif /* CONFIG_BCM63XX_CPU_6345 */
/*
-@@ -1268,6 +1281,7 @@ static const struct board_info __initcon
+@@ -1312,6 +1325,7 @@ static const struct board_info __initcon
#endif /* CONFIG_BCM63XX_CPU_6338 */
#ifdef CONFIG_BCM63XX_CPU_6345
&board_96345gw2,
#endif /* CONFIG_BCM63XX_CPU_6345 */
#ifdef CONFIG_BCM63XX_CPU_6348
&board_96348r,
-@@ -1323,6 +1337,8 @@ static struct of_device_id const bcm963x
+@@ -1368,6 +1382,8 @@ static struct of_device_id const bcm963x
#endif /* CONFIG_BCM63XX_CPU_6338 */
#ifdef CONFIG_BCM63XX_CPU_6345
{ .compatible = "brcm,bcm96345gw2", .data = &board_96345gw2, },
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1135,6 +1135,275 @@ static struct board_info __initdata boar
+@@ -1178,6 +1178,275 @@ static struct board_info __initdata boar
.has_ohci0 = 1,
};
#endif /* CONFIG_BCM63XX_CPU_6348 */
/*
-@@ -1292,6 +1561,19 @@ static const struct board_info __initcon
+@@ -1336,6 +1605,19 @@ static const struct board_info __initcon
&board_DV201AMR,
&board_96348gw_a,
&board_rta1025w_16,
#endif /* CONFIG_BCM63XX_CPU_6348 */
#ifdef CONFIG_BCM63XX_CPU_6358
&board_96358vw,
-@@ -1341,15 +1623,29 @@ static struct of_device_id const bcm963x
+@@ -1386,15 +1668,29 @@ static struct of_device_id const bcm963x
{ .compatible = "dynalink,rta770w", .data = &board_rta770w, },
#endif /* CONFIG_BCM63XX_CPU_6345 */
#ifdef CONFIG_BCM63XX_CPU_6348
#include <asm/addrspace.h>
#include <bcm63xx_board.h>
#include <bcm63xx_cpu.h>
-@@ -1488,6 +1489,88 @@ static struct board_info __initdata boar
+@@ -1531,6 +1532,88 @@ static struct board_info __initdata boar
.has_ehci0 = 1,
};
static struct board_info __initdata board_DWVS0 = {
.name = "DWV-S0",
.expected_cpu_id = 0x6358,
-@@ -1512,6 +1595,238 @@ static struct board_info __initdata boar
+@@ -1555,6 +1638,238 @@ static struct board_info __initdata boar
.has_ohci0 = 1,
.has_ehci0 = 1,
};
#endif /* CONFIG_BCM63XX_CPU_6358 */
/*
-@@ -1579,7 +1894,20 @@ static const struct board_info __initcon
+@@ -1623,7 +1938,20 @@ static const struct board_info __initcon
&board_96358vw,
&board_96358vw2,
&board_AGPFS0,
#endif /* CONFIG_BCM63XX_CPU_6358 */
};
-@@ -1653,11 +1981,24 @@ static struct of_device_id const bcm963x
+@@ -1698,11 +2026,24 @@ static struct of_device_id const bcm963x
{ .compatible = "alcatel,rg100a", .data = &board_96358vw2, },
{ .compatible = "brcm,bcm96358vw", .data = &board_96358vw, },
{ .compatible = "brcm,bcm96358vw2", .data = &board_96358vw2, },
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1829,6 +1829,117 @@ static struct board_info __initdata boar
+@@ -1872,6 +1872,117 @@ static struct board_info __initdata boar
};
#endif /* CONFIG_BCM63XX_CPU_6358 */
/*
* all boards
*/
-@@ -1909,6 +2020,12 @@ static const struct board_info __initcon
+@@ -1953,6 +2064,12 @@ static const struct board_info __initcon
&board_nb4_fxc_r1,
&board_spw303v,
#endif /* CONFIG_BCM63XX_CPU_6358 */
};
static struct of_device_id const bcm963xx_boards_dt[] = {
-@@ -2001,6 +2118,10 @@ static struct of_device_id const bcm963x
+@@ -2046,6 +2163,10 @@ static struct of_device_id const bcm963x
{ .compatible = "telsey,cpva642", .data = &board_CPVA642, },
#endif /* CONFIG_BCM63XX_CPU_6358 */
#ifdef CONFIG_BCM63XX_CPU_6362
#include <asm/addrspace.h>
#include <bcm63xx_board.h>
#include <bcm63xx_cpu.h>
-@@ -1941,6 +1943,648 @@ static struct board_info __initdata boar
+@@ -1984,6 +1986,648 @@ static struct board_info __initdata boar
#endif /* CONFIG_BCM63XX_CPU_6362 */
/*
* all boards
*/
static const struct board_info __initconst *bcm963xx_boards[] = {
-@@ -2026,6 +2670,22 @@ static const struct board_info __initcon
+@@ -2070,6 +2714,22 @@ static const struct board_info __initcon
&board_hg253s_v2,
&board_nb6,
#endif /* CONFIG_BCM63XX_CPU_6362 */
};
static struct of_device_id const bcm963xx_boards_dt[] = {
-@@ -2124,6 +2784,20 @@ static struct of_device_id const bcm963x
+@@ -2169,6 +2829,20 @@ static struct of_device_id const bcm963x
{ .compatible = "sfr,neufbox-6-sercomm-r0", .data = &board_nb6, },
#endif /* CONFIG_BCM63XX_CPU_6362 */
#ifdef CONFIG_BCM63XX_CPU_6368
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2585,6 +2585,273 @@ static struct board_info __initdata boar
+@@ -2628,6 +2628,273 @@ static struct board_info __initdata boar
#endif /* CONFIG_BCM63XX_CPU_6368 */
/*
* all boards
*/
static const struct board_info __initconst *bcm963xx_boards[] = {
-@@ -2686,6 +2953,15 @@ static const struct board_info __initcon
+@@ -2730,6 +2997,15 @@ static const struct board_info __initcon
&board_VR3026e,
&board_WAP5813n,
#endif /* CONFIG_BCM63XX_CPU_6368 */
};
static struct of_device_id const bcm963xx_boards_dt[] = {
-@@ -2800,6 +3076,14 @@ static struct of_device_id const bcm963x
+@@ -2845,6 +3121,14 @@ static struct of_device_id const bcm963x
{ .compatible = "zyxel,p870hw-51a-v2", .data = &board_P870HW51A_V2, },
#endif /* CONFIG_BCM63XX_CPU_6368 */
#ifdef CONFIG_BCM63XX_CPU_63268
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -3112,6 +3112,22 @@ void __init board_bcm963xx_init(void)
+@@ -3157,6 +3157,22 @@ void __init board_bcm963xx_init(void)
val &= MPI_CSBASE_BASE_MASK;
}
boot_addr = (u8 *)KSEG1ADDR(val);
projects / openwrt / staging / jow.git / commitdiff