sf command: allow default bus and chip selects

This patch allows a board configuration file to provide default bus
and chip-selects for SPI flash so that first argument to the 'sf' command
is optional.

On boards that use the mxc_spi driver and a GPIO for chip select, this allows
a much simpler command line:
	U-Boot> sf probe
instead of
	U-Boot> sf probe 0x5300

Tested-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

diff --git a/common/cmd_sf.c b/common/cmd_sf.c
index 612fd18617acbed68b099c177c53c0287b5ff056..98e4162114d689dacb903cd4943f39b6e1bee4a7 100644 (file)
--- a/common/cmd_sf.c
+++ b/common/cmd_sf.c
@@ -17,6 +17,12 @@
 #ifndef CONFIG_SF_DEFAULT_MODE
 # define CONFIG_SF_DEFAULT_MODE                SPI_MODE_3
 #endif
+#ifndef CONFIG_SF_DEFAULT_CS
+# define CONFIG_SF_DEFAULT_CS          0
+#endif
+#ifndef CONFIG_SF_DEFAULT_BUS
+# define CONFIG_SF_DEFAULT_BUS         0
+#endif
 
 static struct spi_flash *flash;
 
@@ -63,27 +69,26 @@ static int sf_parse_len_arg(char *arg, ulong *len)
 
 static int do_spi_flash_probe(int argc, char * const argv[])
 {
-       unsigned int bus = 0;
-       unsigned int cs;
+       unsigned int bus = CONFIG_SF_DEFAULT_BUS;
+       unsigned int cs = CONFIG_SF_DEFAULT_CS;
        unsigned int speed = CONFIG_SF_DEFAULT_SPEED;
        unsigned int mode = CONFIG_SF_DEFAULT_MODE;
        char *endp;
        struct spi_flash *new;
 
-       if (argc < 2)
-               return -1;
-
-       cs = simple_strtoul(argv[1], &endp, 0);
-       if (*argv[1] == 0 || (*endp != 0 && *endp != ':'))
-               return -1;
-       if (*endp == ':') {
-               if (endp[1] == 0)
-                       return -1;
-
-               bus = cs;
-               cs = simple_strtoul(endp + 1, &endp, 0);
-               if (*endp != 0)
+       if (argc >= 2) {
+               cs = simple_strtoul(argv[1], &endp, 0);
+               if (*argv[1] == 0 || (*endp != 0 && *endp != ':'))
                        return -1;
+               if (*endp == ':') {
+                       if (endp[1] == 0)
+                               return -1;
+
+                       bus = cs;
+                       cs = simple_strtoul(endp + 1, &endp, 0);
+                       if (*endp != 0)
+                               return -1;
+               }
        }
 
        if (argc >= 3) {
@@ -299,7 +304,7 @@ usage:
 U_BOOT_CMD(
        sf,     5,      1,      do_spi_flash,
        "SPI flash sub-system",
-       "probe [bus:]cs [hz] [mode]     - init flash device on given SPI bus\n"
+       "probe [[bus:]cs] [hz] [mode]   - init flash device on given SPI bus\n"
        "                                 and chip select\n"
        "sf read addr offset len        - read `len' bytes starting at\n"
        "                                 `offset' to memory at `addr'\n"