rockchip: add Orange Pi R1 Plus support

Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.

This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.

Note: booting from SPI is currently unsupported, you have to install
the image on a SD card.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit ab641efe698f4412319fcbcfe6ffde64c929cd97)
[Removed patches for kernel 6.1]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>

diff --git a/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds b/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds
index 2c9206b03ed85e6d78584c6c1a825ebeb1b58397..f0da262a094e3607d32516602361b28527597d9b 100644 (file)
--- a/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds
+++ b/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds
@@ -10,7 +10,8 @@ board_config_update
 case $board in
 friendlyarm,nanopi-r2c|\
 friendlyarm,nanopi-r2s|\
-friendlyarm,nanopi-r4s)
+friendlyarm,nanopi-r4s|\
+xunlong,orangepi-r1-plus)
        ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth0"
        ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth1"
        ;;

diff --git a/target/linux/rockchip/armv8/base-files/etc/board.d/02_network b/target/linux/rockchip/armv8/base-files/etc/board.d/02_network
index 16ba01b7e313c8085b010037fa0a8cc97dbaf74d..f7e0da67b27144377f2cd50805b1e2f9e5928dde 100644 (file)
--- a/target/linux/rockchip/armv8/base-files/etc/board.d/02_network
+++ b/target/linux/rockchip/armv8/base-files/etc/board.d/02_network
@@ -8,7 +8,8 @@ rockchip_setup_interfaces()
 
        case "$board" in
        friendlyarm,nanopi-r2s|\
-       friendlyarm,nanopi-r4s)
+       friendlyarm,nanopi-r4s|\
+       xunlong,orangepi-r1-plus)
                ucidef_set_interfaces_lan_wan 'eth1' 'eth0'
                ;;
        *)
@@ -55,6 +56,9 @@ rockchip_setup_macs()
                wan_mac=$(nanopi_r4s_get_mac wan)
                lan_mac=$(nanopi_r4s_get_mac lan)
                ;;
+       xunlong,orangepi-r1-plus)
+               wan_mac=$(macaddr_add "$(cat /sys/class/net/eth1/address)" -1)
+               ;;
        esac
 
        [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac

diff --git a/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity b/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity
index 3d1d99128ecfdc36482c84631b00ec49b4d1e890..660a7e286671bcfef62c464fb34c4916c4aaedf2 100644 (file)
--- a/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity
+++ b/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity
@@ -30,7 +30,8 @@ set_interface_core() {
 
 case "$(board_name)" in
 friendlyarm,nanopi-r2c|\
-friendlyarm,nanopi-r2s)
+friendlyarm,nanopi-r2s|\
+xunlong,orangepi-r1-plus)
        set_interface_core 2 "eth0"
        set_interface_core 4 "eth1" "xhci-hcd:usb3"
        ;;

diff --git a/target/linux/rockchip/image/armv8.mk b/target/linux/rockchip/image/armv8.mk
index 601ddcbdd6b9aac91735ccb7a43c64c710064038..9a32a07b21aff033b5d0a527a4f94088fb4cb986 100644 (file)
--- a/target/linux/rockchip/image/armv8.mk
+++ b/target/linux/rockchip/image/armv8.mk
@@ -60,3 +60,12 @@ define Device/radxa_rock-pi-4a
   IMAGE/sysupgrade.img.gz := boot-common | boot-script | pine64-img | gzip | append-metadata
 endef
 TARGET_DEVICES += radxa_rock-pi-4a
+
+define Device/xunlong_orangepi-r1-plus
+  DEVICE_VENDOR := Xunlong
+  DEVICE_MODEL := Orange Pi R1 Plus
+  SOC := rk3328
+  IMAGE/sysupgrade.img.gz := boot-common | boot-script | pine64-img | gzip | append-metadata
+  DEVICE_PACKAGES := kmod-usb-net-rtl8152
+endef
+TARGET_DEVICES += xunlong_orangepi-r1-plus

diff --git a/target/linux/rockchip/patches-5.15/007-v6.3-arm64-dts-rockchip-rk3328-Add-Orange-Pi-R1-Plus.patch b/target/linux/rockchip/patches-5.15/007-v6.3-arm64-dts-rockchip-rk3328-Add-Orange-Pi-R1-Plus.patch
new file mode 100644 (file)
index 0000000..053a4d0
--- /dev/null
+++ b/target/linux/rockchip/patches-5.15/007-v6.3-arm64-dts-rockchip-rk3328-Add-Orange-Pi-R1-Plus.patch
@@ -0,0 +1,407 @@
+From 51712e1d014aaaa4c6e1e7e84932d58b5c0f59ed Mon Sep 17 00:00:00 2001
+From: Chukun Pan <amadeus@jmu.edu.cn>
+Date: Sat, 3 Dec 2022 15:41:49 +0800
+Subject: [PATCH] arm64: dts: rockchip: rk3328: Add Orange Pi R1 Plus
+
+Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
+
+This device is similar to the NanoPi R2S, and has a 16MB
+SPI NOR (mx25l12805d). The reset button is changed to
+directly reset the power supply, another detail is that
+both network ports have independent MAC addresses.
+
+Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
+Link: https://lore.kernel.org/r/20221203074149.11543-3-amadeus@jmu.edu.cn
+Signed-off-by: Heiko Stuebner <heiko@sntech.de>
+---
+ arch/arm64/boot/dts/rockchip/Makefile         |   1 +
+ .../dts/rockchip/rk3328-orangepi-r1-plus.dts  | 373 ++++++++++++++++++
+ 2 files changed, 374 insertions(+)
+ create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts
+
+--- a/arch/arm64/boot/dts/rockchip/Makefile
++++ b/arch/arm64/boot/dts/rockchip/Makefile
+@@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2c.dtb
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
++dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-orangepi-r1-plus.dtb
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
+--- /dev/null
++++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts
+@@ -0,0 +1,373 @@
++// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
++/*
++ * Based on rk3328-nanopi-r2s.dts, which is:
++ *   Copyright (c) 2020 David Bauer <mail@david-bauer.net>
++ */
++
++/dts-v1/;
++
++#include <dt-bindings/gpio/gpio.h>
++#include <dt-bindings/leds/common.h>
++#include "rk3328.dtsi"
++
++/ {
++      model = "Xunlong Orange Pi R1 Plus";
++      compatible = "xunlong,orangepi-r1-plus", "rockchip,rk3328";
++
++      aliases {
++              ethernet1 = &rtl8153;
++              mmc0 = &sdmmc;
++      };
++
++      chosen {
++              stdout-path = "serial2:1500000n8";
++      };
++
++      gmac_clk: gmac-clock {
++              compatible = "fixed-clock";
++              clock-frequency = <125000000>;
++              clock-output-names = "gmac_clkin";
++              #clock-cells = <0>;
++      };
++
++      leds {
++              compatible = "gpio-leds";
++              pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
++              pinctrl-names = "default";
++
++              led-0 {
++                      function = LED_FUNCTION_LAN;
++                      color = <LED_COLOR_ID_GREEN>;
++                      gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
++              };
++
++              led-1 {
++                      function = LED_FUNCTION_STATUS;
++                      color = <LED_COLOR_ID_RED>;
++                      gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
++                      linux,default-trigger = "heartbeat";
++              };
++
++              led-2 {
++                      function = LED_FUNCTION_WAN;
++                      color = <LED_COLOR_ID_GREEN>;
++                      gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
++              };
++      };
++
++      vcc_sd: sdmmc-regulator {
++              compatible = "regulator-fixed";
++              gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
++              pinctrl-0 = <&sdmmc0m1_pin>;
++              pinctrl-names = "default";
++              regulator-name = "vcc_sd";
++              regulator-boot-on;
++              vin-supply = <&vcc_io>;
++      };
++
++      vcc_sys: vcc-sys-regulator {
++              compatible = "regulator-fixed";
++              regulator-name = "vcc_sys";
++              regulator-always-on;
++              regulator-boot-on;
++              regulator-min-microvolt = <5000000>;
++              regulator-max-microvolt = <5000000>;
++      };
++
++      vdd_5v_lan: vdd-5v-lan-regulator {
++              compatible = "regulator-fixed";
++              enable-active-high;
++              gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;
++              pinctrl-0 = <&lan_vdd_pin>;
++              pinctrl-names = "default";
++              regulator-name = "vdd_5v_lan";
++              regulator-always-on;
++              regulator-boot-on;
++              vin-supply = <&vcc_sys>;
++      };
++};
++
++&cpu0 {
++      cpu-supply = <&vdd_arm>;
++};
++
++&cpu1 {
++      cpu-supply = <&vdd_arm>;
++};
++
++&cpu2 {
++      cpu-supply = <&vdd_arm>;
++};
++
++&cpu3 {
++      cpu-supply = <&vdd_arm>;
++};
++
++&display_subsystem {
++      status = "disabled";
++};
++
++&gmac2io {
++      assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
++      assigned-clock-parents = <&gmac_clk>, <&gmac_clk>;
++      clock_in_out = "input";
++      phy-handle = <&rtl8211e>;
++      phy-mode = "rgmii";
++      phy-supply = <&vcc_io>;
++      pinctrl-0 = <&rgmiim1_pins>;
++      pinctrl-names = "default";
++      snps,aal;
++      rx_delay = <0x18>;
++      tx_delay = <0x24>;
++      status = "okay";
++
++      mdio {
++              compatible = "snps,dwmac-mdio";
++              #address-cells = <1>;
++              #size-cells = <0>;
++
++              rtl8211e: ethernet-phy@1 {
++                      reg = <1>;
++                      pinctrl-0 = <&eth_phy_reset_pin>;
++                      pinctrl-names = "default";
++                      reset-assert-us = <10000>;
++                      reset-deassert-us = <50000>;
++                      reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
++              };
++      };
++};
++
++&i2c1 {
++      status = "okay";
++
++      rk805: pmic@18 {
++              compatible = "rockchip,rk805";
++              reg = <0x18>;
++              interrupt-parent = <&gpio1>;
++              interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
++              #clock-cells = <1>;
++              clock-output-names = "xin32k", "rk805-clkout2";
++              gpio-controller;
++              #gpio-cells = <2>;
++              pinctrl-0 = <&pmic_int_l>;
++              pinctrl-names = "default";
++              rockchip,system-power-controller;
++              wakeup-source;
++
++              vcc1-supply = <&vcc_sys>;
++              vcc2-supply = <&vcc_sys>;
++              vcc3-supply = <&vcc_sys>;
++              vcc4-supply = <&vcc_sys>;
++              vcc5-supply = <&vcc_io>;
++              vcc6-supply = <&vcc_sys>;
++
++              regulators {
++                      vdd_log: DCDC_REG1 {
++                              regulator-name = "vdd_log";
++                              regulator-always-on;
++                              regulator-boot-on;
++                              regulator-min-microvolt = <712500>;
++                              regulator-max-microvolt = <1450000>;
++                              regulator-ramp-delay = <12500>;
++
++                              regulator-state-mem {
++                                      regulator-on-in-suspend;
++                                      regulator-suspend-microvolt = <1000000>;
++                              };
++                      };
++
++                      vdd_arm: DCDC_REG2 {
++                              regulator-name = "vdd_arm";
++                              regulator-always-on;
++                              regulator-boot-on;
++                              regulator-min-microvolt = <712500>;
++                              regulator-max-microvolt = <1450000>;
++                              regulator-ramp-delay = <12500>;
++
++                              regulator-state-mem {
++                                      regulator-on-in-suspend;
++                                      regulator-suspend-microvolt = <950000>;
++                              };
++                      };
++
++                      vcc_ddr: DCDC_REG3 {
++                              regulator-name = "vcc_ddr";
++                              regulator-always-on;
++                              regulator-boot-on;
++
++                              regulator-state-mem {
++                                      regulator-on-in-suspend;
++                              };
++                      };
++
++                      vcc_io: DCDC_REG4 {
++                              regulator-name = "vcc_io";
++                              regulator-always-on;
++                              regulator-boot-on;
++                              regulator-min-microvolt = <3300000>;
++                              regulator-max-microvolt = <3300000>;
++
++                              regulator-state-mem {
++                                      regulator-on-in-suspend;
++                                      regulator-suspend-microvolt = <3300000>;
++                              };
++                      };
++
++                      vcc_18: LDO_REG1 {
++                              regulator-name = "vcc_18";
++                              regulator-always-on;
++                              regulator-boot-on;
++                              regulator-min-microvolt = <1800000>;
++                              regulator-max-microvolt = <1800000>;
++
++                              regulator-state-mem {
++                                      regulator-on-in-suspend;
++                                      regulator-suspend-microvolt = <1800000>;
++                              };
++                      };
++
++                      vcc18_emmc: LDO_REG2 {
++                              regulator-name = "vcc18_emmc";
++                              regulator-always-on;
++                              regulator-boot-on;
++                              regulator-min-microvolt = <1800000>;
++                              regulator-max-microvolt = <1800000>;
++
++                              regulator-state-mem {
++                                      regulator-on-in-suspend;
++                                      regulator-suspend-microvolt = <1800000>;
++                              };
++                      };
++
++                      vdd_10: LDO_REG3 {
++                              regulator-name = "vdd_10";
++                              regulator-always-on;
++                              regulator-boot-on;
++                              regulator-min-microvolt = <1000000>;
++                              regulator-max-microvolt = <1000000>;
++
++                              regulator-state-mem {
++                                      regulator-on-in-suspend;
++                                      regulator-suspend-microvolt = <1000000>;
++                              };
++                      };
++              };
++      };
++};
++
++&io_domains {
++      pmuio-supply = <&vcc_io>;
++      vccio1-supply = <&vcc_io>;
++      vccio2-supply = <&vcc18_emmc>;
++      vccio3-supply = <&vcc_io>;
++      vccio4-supply = <&vcc_io>;
++      vccio5-supply = <&vcc_io>;
++      vccio6-supply = <&vcc_io>;
++      status = "okay";
++};
++
++&pinctrl {
++      gmac2io {
++              eth_phy_reset_pin: eth-phy-reset-pin {
++                      rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
++              };
++      };
++
++      leds {
++              lan_led_pin: lan-led-pin {
++                      rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
++              };
++
++              sys_led_pin: sys-led-pin {
++                      rockchip,pins = <3 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
++              };
++
++              wan_led_pin: wan-led-pin {
++                      rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
++              };
++      };
++
++      lan {
++              lan_vdd_pin: lan-vdd-pin {
++                      rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
++              };
++      };
++
++      pmic {
++              pmic_int_l: pmic-int-l {
++                      rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
++              };
++      };
++};
++
++&pwm2 {
++      status = "okay";
++};
++
++&sdmmc {
++      bus-width = <4>;
++      cap-sd-highspeed;
++      disable-wp;
++      pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
++      pinctrl-names = "default";
++      vmmc-supply = <&vcc_sd>;
++      status = "okay";
++};
++
++&spi0 {
++      status = "okay";
++
++      flash@0 {
++              compatible = "jedec,spi-nor";
++              reg = <0>;
++              spi-max-frequency = <50000000>;
++      };
++};
++
++&tsadc {
++      rockchip,hw-tshut-mode = <0>;
++      rockchip,hw-tshut-polarity = <0>;
++      status = "okay";
++};
++
++&u2phy {
++      status = "okay";
++};
++
++&u2phy_host {
++      status = "okay";
++};
++
++&u2phy_otg {
++      status = "okay";
++};
++
++&uart2 {
++      status = "okay";
++};
++
++&usb20_otg {
++      dr_mode = "host";
++      status = "okay";
++};
++
++&usbdrd3 {
++      dr_mode = "host";
++      status = "okay";
++      #address-cells = <1>;
++      #size-cells = <0>;
++
++      /* Second port is for USB 3.0 */
++      rtl8153: device@2 {
++              compatible = "usbbda,8153";
++              reg = <2>;
++      };
++};
++
++&usb_host0_ehci {
++      status = "okay";
++};
++
++&usb_host0_ohci {
++      status = "okay";
++};

diff --git a/target/linux/rockchip/patches-5.15/107-arm64-dts-rockchip-Update-LED-properties-for-Orange-.patch b/target/linux/rockchip/patches-5.15/107-arm64-dts-rockchip-Update-LED-properties-for-Orange-.patch
new file mode 100644 (file)
index 0000000..b1e26d4
--- /dev/null
+++ b/target/linux/rockchip/patches-5.15/107-arm64-dts-rockchip-Update-LED-properties-for-Orange-.patch
@@ -0,0 +1,56 @@
+From d2166e3b3680bd2b206aebf1e1ce4c0d346f3c50 Mon Sep 17 00:00:00 2001
+From: Tianling Shen <cnsztl@gmail.com>
+Date: Fri, 19 May 2023 12:10:52 +0800
+Subject: [PATCH] arm64: dts: rockchip: Update LED properties for Orange Pi R1
+ Plus
+
+Add OpenWrt's LED aliases for showing system status.
+Also replace function/color with legacy label as OpenWrt relys on it
+to update LED settings.
+
+Signed-off-by: Tianling Shen <cnsztl@gmail.com>
+---
+ .../dts/rockchip/rk3328-orangepi-r1-plus.dts    | 17 +++++++++--------
+ 1 file changed, 9 insertions(+), 8 deletions(-)
+
+--- a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts
++++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts
+@@ -17,6 +17,11 @@
+       aliases {
+               ethernet1 = &rtl8153;
+               mmc0 = &sdmmc;
++
++              led-boot = &status_led;
++              led-failsafe = &status_led;
++              led-running = &status_led;
++              led-upgrade = &status_led;
+       };
+ 
+       chosen {
+@@ -36,22 +41,18 @@
+               pinctrl-names = "default";
+ 
+               led-0 {
+-                      function = LED_FUNCTION_LAN;
+-                      color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
++                      label = "green:lan";
+               };
+ 
+-              led-1 {
+-                      function = LED_FUNCTION_STATUS;
+-                      color = <LED_COLOR_ID_RED>;
++              status_led: led-1 {
+                       gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
+-                      linux,default-trigger = "heartbeat";
++                      label = "red:status";
+               };
+ 
+               led-2 {
+-                      function = LED_FUNCTION_WAN;
+-                      color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
++                      label = "green:wan";
+               };
+       };
+ 

diff --git a/target/linux/rockchip/patches-5.15/108-arm64-dts-rockchip-add-LED-configuration-to-Orange-P.patch b/target/linux/rockchip/patches-5.15/108-arm64-dts-rockchip-add-LED-configuration-to-Orange-P.patch
new file mode 100644 (file)
index 0000000..37b5992
--- /dev/null
+++ b/target/linux/rockchip/patches-5.15/108-arm64-dts-rockchip-add-LED-configuration-to-Orange-P.patch
@@ -0,0 +1,24 @@
+From b46a530d12ada422b9d5b2b97059e0d3ed950b40 Mon Sep 17 00:00:00 2001
+From: Tianling Shen <cnsztl@gmail.com>
+Date: Fri, 19 May 2023 12:38:04 +0800
+Subject: [PATCH] arm64: dts: rockchip: add LED configuration to Orange Pi R1
+ Plus
+
+Add the correct value for the RTL8153 LED configuration register to
+match the blink behavior of the other port on the device.
+
+Signed-off-by: Tianling Shen <cnsztl@gmail.com>
+---
+ arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts | 1 +
+ 1 file changed, 1 insertion(+)
+
+--- a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts
++++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts
+@@ -362,6 +362,7 @@
+       rtl8153: device@2 {
+               compatible = "usbbda,8153";
+               reg = <2>;
++              realtek,led-data = <0x87>;
+       };
+ };
+