--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9132.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ aliases {
+ led-boot = &led_diag;
+ led-failsafe = &led_security;
+ led-upgrade = &led_diag;
+ };
+
+ clock40mhz: ref {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ };
+
+ gpio2: gpio-extender {
+ compatible = "nxp,74hc153-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ // GPIOs used by this node
+ gpio-s0 = <&gpio 9 GPIO_ACTIVE_HIGH>;
+ gpio-s1 = <&gpio 11 GPIO_ACTIVE_HIGH>;
+ gpio-1y = <&gpio 12 GPIO_ACTIVE_HIGH>;
+ gpio-2y = <&gpio 14 GPIO_ACTIVE_HIGH>;
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <20>;
+
+ aoss {
+ label = "aoss";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ router_on {
+ label = "router_on";
+ linux,code = <BTN_5>;
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ debounce-interval = <60>;
+ };
+
+ movie_off {
+ label = "movie_off";
+ linux,code = <BTN_3>;
+ gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ debounce-interval = <60>;
+ };
+
+ usb {
+ label = "usb";
+ linux,code = <BTN_2>;
+ gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ router_auto {
+ label = "router_auto";
+ linux,code = <BTN_6>;
+ gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+ debounce-interval = <60>;
+ };
+
+ movie_on {
+ label = "movie_on";
+ linux,code = <BTN_4>;
+ gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
+ debounce-interval = <60>;
+ };
+ };
+
+ flash@1e000000 {
+ compatible = "cfi-flash";
+ reg = <0x1e000000 0x2000000>;
+ bank-width = <2>;
+ device-width = <2>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x0040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x0040000 0x0020000>;
+ read-only;
+ };
+
+ partition@60000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x0060000 0x1f60000>;
+ };
+
+ partition@1fc0000 {
+ label = "user_property";
+ reg = <0x1fc0000 0x0020000>;
+ read-only;
+ };
+
+ art: partition@1fe0000 {
+ label = "art";
+ reg = <0x1fe0000 0x020000>;
+ read-only;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ usb {
+ label = "blue:usb";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&hub_port>;
+ linux,default-trigger = "usbport";
+ };
+
+ led_diag: diag {
+ label = "red:diag";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ wireless {
+ label = "green:wireless";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led_security: security {
+ label = "amber:security";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+
+ router {
+ label = "green:router";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ switch: switch {
+ status = "disabled";
+
+ gpio-sda = <&gpio 19 GPIO_ACTIVE_HIGH>;
+ gpio-sck = <&gpio 20 GPIO_ACTIVE_HIGH>;
+ mii-bus = <&mdio0>;
+
+ mdio-bus {
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy-mask = <0x10>;
+
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ phy-mode = "rgmii";
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+};
+
+ð0 {
+ status = "disabled";
+
+ phy-mode = "rgmii";
+ mtd-mac-address = <&art 0x1120c>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&mdio1 {
+ status = "okay";
+};
+
+ð1 {
+ status = "disabled";
+
+ compatible = "qca,ar9130-eth", "syscon";
+ reg = <0x1a000000 0x200
+ 0x18070004 0x4>;
+
+ pll-reg = <0x4 0x18 22>;
+ pll-handle = <&pll>;
+
+ phy-mode = "rgmii";
+ phy-handle = <&phy4>;
+ resets = <&rst 13>;
+ reset-names = "mac";
+ qca,mac-idx = <1>;
+ mtd-mac-address = <&art 0x1120c>;
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x11000>;
+};
+
+&uart {
+ status = "okay";
+};
+
+&pll {
+ clocks = <&clock40mhz>;
+};
+
+&usb {
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub_port: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&usb_phy {
+ status = "okay";
+};
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
;;
+ buffalo,wzr-hp-g300nh-rb|\
+ buffalo,wzr-hp-g300nh-s|\
+ dlink,dir-825-b1)
+ ucidef_set_interface_wan "eth1"
+ ucidef_add_switch "switch0" \
+ "0:lan" "1:lan" "2:lan" "3:lan" "5@eth0"
+ ;;
buffalo,wzr-hp-g302h-a1a0)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:1" "3:lan:4" "4:lan:3" "5:lan:2" "2:wan"
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:2" "2:lan:1"
;;
- dlink,dir-825-b1)
- ucidef_set_interface_wan "eth1"
- ucidef_add_switch "switch0" \
- "0:lan" "1:lan" "2:lan" "3:lan" "5@eth0"
- ;;
dlink,dir-825-c1|\
dlink,dir-835-a1|\
dlink,dir-842-c1|\
endef
TARGET_DEVICES += buffalo_wzr-hp-ag300h
+define Device/buffalo_wzr-hp-g300nh
+ $(Device/buffalo_common)
+ SOC := ar9132
+ BUFFALO_PRODUCT := WZR-HP-G300NH
+ BUFFALO_HWVER := 1
+ DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-gpio-nxp-74hc153
+ BLOCKSIZE := 128k
+ IMAGE_SIZE := 32128k
+ SUPPORTED_DEVICES += wzr-hp-g300nh
+endef
+
+define Device/buffalo_wzr-hp-g300nh-rb
+ $(Device/buffalo_wzr-hp-g300nh)
+ DEVICE_MODEL := WZR-HP-G300NH (RTL8366RB switch)
+endef
+TARGET_DEVICES += buffalo_wzr-hp-g300nh-rb
+
+define Device/buffalo_wzr-hp-g300nh-s
+ $(Device/buffalo_wzr-hp-g300nh)
+ DEVICE_MODEL := WZR-HP-G300NH (RTL8366S switch)
+endef
+TARGET_DEVICES += buffalo_wzr-hp-g300nh-s
+
define Device/buffalo_wzr-hp-g302h-a1a0
$(Device/buffalo_common)
SOC := ar7242
projects / openwrt / staging / hauke.git / commitdiff