This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7621_tplink_rexx0-v1.dtsi"
+
+/ {
+ compatible = "tplink,re500-v1", "mediatek,mt7621-soc";
+ model = "TP-Link RE500 v1";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "re500-v1:blue:power";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi2g {
+ label = "re500-v1:blue:wifi2g";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wifi5g {
+ label = "re500-v1:blue:wifi5g";
+ gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wps_red {
+ label = "re500-v1:red:wps";
+ gpios = <&gpio 26 GPIO_ACTIVE_HIGH>;
+ };
+
+ wps_blue {
+ label = "re500-v1:blue:wps";
+ gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ eth_act {
+ label = "re500-v1:green:eth_act";
+ gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+ };
+
+ eth_link {
+ label = "re500-v1:green:eth_link";
+ gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "rgmii2", "wdt";
+ function = "gpio";
+ };
+};
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
-#include "mt7621.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "mt7621_tplink_rexx0-v1.dtsi"
/ {
compatible = "tplink,re650-v1", "mediatek,mt7621-soc";
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
- label-mac-device = &gmac0;
- };
-
- chosen {
- bootargs = "console=ttyS0,57600";
};
leds {
gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
};
};
-
- keys {
- compatible = "gpio-keys";
-
- wps {
- label = "wps";
- gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- linux,code = <KEY_WPS_BUTTON>;
- };
-
- power {
- label = "power";
- gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- linux,code = <KEY_POWER>;
- };
-
- led {
- label = "led";
- gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- linux,code = <KEY_LIGHTS_TOGGLE>;
- };
-
- reset {
- label = "reset";
- gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- linux,code = <KEY_RESTART>;
- };
- };
};
-&spi0 {
- status = "okay";
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <40000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "u-boot";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- partition@20000 {
- compatible = "tplink,firmware";
- label = "firmware";
- reg = <0x20000 0xde0000>;
- };
-
- config: partition@e00000 {
- label = "config";
- reg = <0xe00000 0x50000>;
- read-only;
- };
-
- /* range 0xe50000 to 0xff0000 is empty in vendor
- * firmware, so we do not use it either
- */
-
- radio: partition@ff0000 {
- label = "radio";
- reg = <0xff0000 0x10000>;
- read-only;
- };
- };
- };
-};
-
-&pcie {
- status = "okay";
-};
-
-&pcie0 {
- wifi@0,0 {
- compatible = "mediatek,mt76";
- reg = <0x0000 0 0 0 0>;
- mediatek,mtd-eeprom = <&radio 0x0>;
- mtd-mac-address = <&config 0x10008>;
- mtd-mac-address-increment = <1>;
- ieee80211-freq-limit = <2400000 2500000>;
- };
-};
-
-&pcie1 {
- wifi@0,0 {
- compatible = "mediatek,mt76";
- reg = <0x0000 0 0 0 0>;
- mediatek,mtd-eeprom = <&radio 0x8000>;
- mtd-mac-address = <&config 0x10008>;
- mtd-mac-address-increment = <2>;
- ieee80211-freq-limit = <5000000 6000000>;
- };
-};
-
-&gmac0 {
- mtd-mac-address = <&config 0x10008>;
-};
-
-&switch0 {
- ports {
- port@0 {
- status = "okay";
- label = "lan";
- };
- };
-};
-
-
&state_default {
gpio {
groups = "rgmii2", "wdt";
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ aliases {
+ label-mac-device = &gmac0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,57600";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ power {
+ label = "power";
+ gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ linux,code = <KEY_POWER>;
+ };
+
+ led {
+ label = "led";
+ gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ linux,code = <KEY_LIGHTS_TOGGLE>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ partition@20000 {
+ compatible = "tplink,firmware";
+ label = "firmware";
+ reg = <0x20000 0xde0000>;
+ };
+
+ config: partition@e00000 {
+ label = "config";
+ reg = <0xe00000 0x50000>;
+ read-only;
+ };
+
+ /* range 0xe50000 to 0xff0000 is empty in vendor
+ * firmware, so we do not use it either
+ */
+
+ radio: partition@ff0000 {
+ label = "radio";
+ reg = <0xff0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi@0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&radio 0x0>;
+ mtd-mac-address = <&config 0x10008>;
+ mtd-mac-address-increment = <1>;
+ ieee80211-freq-limit = <2400000 2500000>;
+ };
+};
+
+&pcie1 {
+ wifi@0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&radio 0x8000>;
+ mtd-mac-address = <&config 0x10008>;
+ mtd-mac-address-increment = <2>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+};
+
+&gmac0 {
+ mtd-mac-address = <&config 0x10008>;
+};
+
+&switch0 {
+ ports {
+ port@0 {
+ status = "okay";
+ label = "lan";
+ };
+ };
+};
endef
TARGET_DEVICES += tplink_re350-v1
+define Device/tplink_re500-v1
+ $(Device/tplink-safeloader)
+ DEVICE_MODEL := RE500
+ DEVICE_VARIANT := v1
+ DEVICE_PACKAGES := kmod-mt7615e wpad-basic
+ TPLINK_BOARD_ID := RE500-V1
+ IMAGE_SIZE := 14208k
+endef
+TARGET_DEVICES += tplink_re500-v1
+
define Device/tplink_re650-v1
$(Device/tplink-safeloader)
DEVICE_MODEL := RE650
ucidef_set_led_netdev "eth_act" "LAN act" "$boardname:green:eth_act" "lan" "tx rx"
ucidef_set_led_netdev "eth_link" "LAN link" "$boardname:green:eth_link" "lan" "link"
;;
+tplink,re500-v1)
+ ucidef_set_led_netdev "eth_act" "LAN act" "$boardname:green:eth_act" "lan" "tx rx"
+ ucidef_set_led_netdev "eth_link" "LAN link" "$boardname:green:eth_link" "lan" "link"
+ ;;
xzwifi,creativebox-v1)
ucidef_set_led_netdev "internet" "internet" "$boardname:blue:internet" "wan"
;;
netgear,ex6150|\
thunder,timecloud|\
tplink,re350-v1|\
+ tplink,re500-v1|\
tplink,re650-v1|\
ubnt,unifi-nanohd)
ucidef_set_interface_lan "lan"
.last_sysupgrade_partition = "file-system"
},
+ /** Firmware layout for the RE500 */
+ {
+ .id = "RE500-V1",
+ .vendor = "",
+ .support_list =
+ "SupportList:\r\n"
+ "{product_name:RE500,product_ver:1.0.0,special_id:00000000}\r\n"
+ "{product_name:RE500,product_ver:1.0.0,special_id:55530000}\r\n"
+ "{product_name:RE500,product_ver:1.0.0,special_id:45550000}\r\n"
+ "{product_name:RE500,product_ver:1.0.0,special_id:4A500000}\r\n"
+ "{product_name:RE500,product_ver:1.0.0,special_id:43410000}\r\n"
+ "{product_name:RE500,product_ver:1.0.0,special_id:41550000}\r\n"
+ "{product_name:RE500,product_ver:1.0.0,special_id:41530000}\r\n",
+ .support_trail = '\x00',
+ .soft_ver = NULL,
+
+ /* We're using a dynamic kernel/rootfs split here */
+ .partitions = {
+ {"fs-uboot", 0x00000, 0x20000},
+ {"firmware", 0x20000, 0xde0000},
+ {"partition-table", 0xe00000, 0x02000},
+ {"default-mac", 0xe10000, 0x00020},
+ {"pin", 0xe10100, 0x00020},
+ {"product-info", 0xe11100, 0x01000},
+ {"soft-version", 0xe20000, 0x01000},
+ {"support-list", 0xe21000, 0x01000},
+ {"profile", 0xe22000, 0x08000},
+ {"user-config", 0xe30000, 0x10000},
+ {"default-config", 0xe40000, 0x10000},
+ {"radio", 0xff0000, 0x10000},
+ {NULL, 0, 0}
+ },
+
+ .first_sysupgrade_partition = "os-image",
+ .last_sysupgrade_partition = "file-system"
+ },
+
/** Firmware layout for the RE650 */
{
.id = "RE650-V1",
projects / openwrt / staging / adrian.git / commitdiff