We should use label instead of redefine the node.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
};
soc {
- pinmux@800000 {
- i2c4_pins: i2c4_pinmux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- bias-disable;
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- drive-strength = <10>;
- bias-none;
- };
- };
- nand_pins: nand_pins {
- disable {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
-
- pullups {
- pins = "gpio39";
- function = "nand";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-bus-hold;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio2", "gpio27", "gpio28",
- "gpio29", "gpio30", "gpio31",
- "gpio32", "gpio51", "gpio52",
- "gpio59", "gpio60", "gpio61",
- "gpio62" , "gpio66";
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
-
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi4: spi@1a280000 {
- status = "okay";
- spi-max-frequency = <50000000>;
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 0>;
-
- m25p80@0 {
- compatible = "s25fl256s1";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- partitions {
- compatible = "qcom,smem";
- };
- };
- };
- };
-
- sata-phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- status = "okay";
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- force_gen1 = <1>;
- };
-
- pcie2: pci@1b900000 {
- status = "okay";
- };
-
- nand-controller@1ac00000 {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "qcom,smem";
- };
- };
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <3>;
};
};
+ };
+};
- gmac0: ethernet@37000000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <0>;
+&qcom_pinmux {
+ i2c4_pins: i2c4_pinmux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ bias-disable;
+ };
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
- mdiobus = <&mdio0>;
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+ };
+ nand_pins: nand_pins {
+ disable {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
+ pullups {
+ pins = "gpio39";
+ function = "nand";
+ drive-strength = <10>;
+ bias-pull-up;
};
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
- mdiobus = <&mdio0>;
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-bus-hold;
+ };
+ };
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio2", "gpio27", "gpio28",
+ "gpio29", "gpio30", "gpio31",
+ "gpio32", "gpio51", "gpio52",
+ "gpio59", "gpio60", "gpio61",
+ "gpio62" , "gpio66";
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
};
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
- mdiobus = <&mdio0>;
+&gsbi5 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "okay";
- fixed-link {
- speed = <1000>;
- full-duplex;
+ spi4: spi@1a280000 {
+ status = "okay";
+ spi-max-frequency = <50000000>;
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 0>;
+
+ m25p80@0 {
+ compatible = "s25fl256s1";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "qcom,smem";
};
};
};
};
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&pcie2 {
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "qcom,smem";
+ };
+ };
+};
+
+&gmac0 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <0>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
&adm_dma {
status = "okay";
};
};
soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio16", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33",
- "gpio53", "gpio66";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- usb0_pwr_en_pin: usb0_pwr_en_pin {
- mux {
- pins = "gpio25";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- output-high;
- };
- };
-
- usb1_pwr_en_pin: usb1_pwr_en_pin {
- mux {
- pins = "gpio23";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- output-high;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi5: spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- m25p80@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- MIBIB@20000 {
- label = "MIBIB";
- reg = <0x20000 0x20000>;
- read-only;
- };
-
- SBL2@40000 {
- label = "SBL2";
- reg = <0x40000 0x20000>;
- read-only;
- };
-
- SBL3@60000 {
- label = "SBL3";
- reg = <0x60000 0x30000>;
- read-only;
- };
-
- DDRCONFIG@90000 {
- label = "DDRCONFIG";
- reg = <0x90000 0x10000>;
- read-only;
- };
-
- SSD@a0000 {
- label = "SSD";
- reg = <0xa0000 0x10000>;
- read-only;
- };
-
- TZ@b0000 {
- label = "TZ";
- reg = <0xb0000 0x30000>;
- read-only;
- };
-
- RPM@e0000 {
- label = "RPM";
- reg = <0xe0000 0x20000>;
- read-only;
- };
-
- fs-uboot@100000 {
- label = "fs-uboot";
- reg = <0x100000 0x70000>;
- read-only;
- };
-
- uboot-env@170000 {
- label = "uboot-env";
- reg = <0x170000 0x40000>;
- read-only;
- };
-
- radio@1b0000 {
- label = "radio";
- reg = <0x1b0000 0x40000>;
- read-only;
- };
-
- os-image@1f0000 {
- label = "os-image";
- reg = <0x1f0000 0x400000>;
- };
-
- rootfs@5f0000 {
- label = "rootfs";
- reg = <0x5f0000 0x1900000>;
- };
-
- defaultmac: default-mac@1ef0000 {
- label = "default-mac";
- reg = <0x1ef0000 0x00200>;
- read-only;
- };
-
- pin@1ef0200 {
- label = "pin";
- reg = <0x1ef0200 0x00200>;
- read-only;
- };
-
- product-info@1ef0400 {
- label = "product-info";
- reg = <0x1ef0400 0x0fc00>;
- read-only;
- };
-
- partition-table@1f00000 {
- label = "partition-table";
- reg = <0x1f00000 0x10000>;
- read-only;
- };
-
- soft-version@1f10000 {
- label = "soft-version";
- reg = <0x1f10000 0x10000>;
- read-only;
- };
-
- support-list@1f20000 {
- label = "support-list";
- reg = <0x1f20000 0x10000>;
- read-only;
- };
-
- profile@1f30000 {
- label = "profile";
- reg = <0x1f30000 0x10000>;
- read-only;
- };
-
- default-config@1f40000 {
- label = "default-config";
- reg = <0x1f40000 0x10000>;
- read-only;
- };
-
- user-config@1f50000 {
- label = "user-config";
- reg = <0x1f50000 0x40000>;
- read-only;
- };
-
- qos-db@1f90000 {
- label = "qos-db";
- reg = <0x1f90000 0x40000>;
- read-only;
- };
-
- usb-config@1fd0000 {
- label = "usb-config";
- reg = <0x1fd0000 0x10000>;
- read-only;
- };
-
- log@1fe0000 {
- label = "log";
- reg = <0x1fe0000 0x20000>;
- read-only;
- };
- };
- };
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pin>;
- pinctrl-names = "default";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pin>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- force_gen1 = <1>;
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
};
};
-
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&defaultmac 0x8>;
- mtd-mac-address-increment = <1>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&defaultmac 0x8>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
};
keys {
};
};
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio16", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33",
+ "gpio53", "gpio66";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ bias-pull-down;
+ };
+
+ data {
+ pins = "gpio18", "gpio19";
+ drive-strength = <10>;
+ };
+
+ cs {
+ pins = "gpio20";
+ function = "gpio";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ clk {
+ pins = "gpio21";
+ drive-strength = <12>;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ usb0_pwr_en_pin: usb0_pwr_en_pin {
+ mux {
+ pins = "gpio25";
+ function = "gpio";
+ drive-strength = <10>;
+ bias-pull-up;
+ output-high;
+ };
+ };
+
+ usb1_pwr_en_pin: usb1_pwr_en_pin {
+ mux {
+ pins = "gpio23";
+ function = "gpio";
+ drive-strength = <10>;
+ bias-pull-up;
+ output-high;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&gsbi5 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "okay";
+
+ spi5: spi@1a280000 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ m25p80@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ MIBIB@20000 {
+ label = "MIBIB";
+ reg = <0x20000 0x20000>;
+ read-only;
+ };
+
+ SBL2@40000 {
+ label = "SBL2";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ SBL3@60000 {
+ label = "SBL3";
+ reg = <0x60000 0x30000>;
+ read-only;
+ };
+
+ DDRCONFIG@90000 {
+ label = "DDRCONFIG";
+ reg = <0x90000 0x10000>;
+ read-only;
+ };
+
+ SSD@a0000 {
+ label = "SSD";
+ reg = <0xa0000 0x10000>;
+ read-only;
+ };
+
+ TZ@b0000 {
+ label = "TZ";
+ reg = <0xb0000 0x30000>;
+ read-only;
+ };
+
+ RPM@e0000 {
+ label = "RPM";
+ reg = <0xe0000 0x20000>;
+ read-only;
+ };
+
+ fs-uboot@100000 {
+ label = "fs-uboot";
+ reg = <0x100000 0x70000>;
+ read-only;
+ };
+
+ uboot-env@170000 {
+ label = "uboot-env";
+ reg = <0x170000 0x40000>;
+ read-only;
+ };
+
+ radio@1b0000 {
+ label = "radio";
+ reg = <0x1b0000 0x40000>;
+ read-only;
+ };
+
+ os-image@1f0000 {
+ label = "os-image";
+ reg = <0x1f0000 0x400000>;
+ };
+
+ rootfs@5f0000 {
+ label = "rootfs";
+ reg = <0x5f0000 0x1900000>;
+ };
+
+ defaultmac: default-mac@1ef0000 {
+ label = "default-mac";
+ reg = <0x1ef0000 0x00200>;
+ read-only;
+ };
+
+ pin@1ef0200 {
+ label = "pin";
+ reg = <0x1ef0200 0x00200>;
+ read-only;
+ };
+
+ product-info@1ef0400 {
+ label = "product-info";
+ reg = <0x1ef0400 0x0fc00>;
+ read-only;
+ };
+
+ partition-table@1f00000 {
+ label = "partition-table";
+ reg = <0x1f00000 0x10000>;
+ read-only;
+ };
+
+ soft-version@1f10000 {
+ label = "soft-version";
+ reg = <0x1f10000 0x10000>;
+ read-only;
+ };
+
+ support-list@1f20000 {
+ label = "support-list";
+ reg = <0x1f20000 0x10000>;
+ read-only;
+ };
+
+ profile@1f30000 {
+ label = "profile";
+ reg = <0x1f30000 0x10000>;
+ read-only;
+ };
+
+ default-config@1f40000 {
+ label = "default-config";
+ reg = <0x1f40000 0x10000>;
+ read-only;
+ };
+
+ user-config@1f50000 {
+ label = "user-config";
+ reg = <0x1f50000 0x40000>;
+ read-only;
+ };
+
+ qos-db@1f90000 {
+ label = "qos-db";
+ reg = <0x1f90000 0x40000>;
+ read-only;
+ };
+
+ usb-config@1fd0000 {
+ label = "usb-config";
+ reg = <0x1fd0000 0x10000>;
+ read-only;
+ };
+
+ log@1fe0000 {
+ label = "log";
+ reg = <0x1fe0000 0x20000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&usb3_0 {
+ status = "okay";
+
+ pinctrl-0 = <&usb0_pwr_en_pin>;
+ pinctrl-names = "default";
+};
+
+&usb3_1 {
+ status = "okay";
+
+ pinctrl-0 = <&usb1_pwr_en_pin>;
+ pinctrl-names = "default";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&defaultmac 0x8>;
+ mtd-mac-address-increment = <1>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&defaultmac 0x8>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
&adm_dma {
status = "okay";
};
};
soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- nand_pins: nand_pins {
- disable {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
-
- pullups {
- pins = "gpio39";
- function = "nand";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-bus-hold;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- ports-implemented = <0x1>;
- status = "okay";
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- force_gen1 = <1>;
- };
-
- nand-controller@1ac00000 {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
- };
-
- artbak: art@1340000 {
- label = "artbak";
- reg = <0x1340000 0x0140000>;
- read-only;
- };
-
- kernel@1480000 {
- label = "kernel";
- reg = <0x1480000 0x0400000>;
- };
-
- ubi@1880000 {
- label = "ubi";
- reg = <0x1880000 0x1C00000>;
- };
-
- netgear@3480000 {
- label = "netgear";
- reg = <0x3480000 0x4480000>;
- read-only;
- };
-
- reserve@7900000 {
- label = "reserve";
- reg = <0x7900000 0x0700000>;
- read-only;
- };
- };
- };
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
};
};
-
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- phy-handle = <&phy4>;
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
- };
-
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
};
keys {
};
};
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+ "gpio24","gpio26", "gpio53", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ disable {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ pullups {
+ pins = "gpio39";
+ function = "nand";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-bus-hold;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ usb0_pwr_en_pins: usb0_pwr_en_pins {
+ mux {
+ pins = "gpio15";
+ function = "gpio";
+ drive-strength = <12>;
+ bias-pull-down;
+ output-high;
+ };
+ };
+
+ usb1_pwr_en_pins: usb1_pwr_en_pins {
+ mux {
+ pins = "gpio16", "gpio68";
+ function = "gpio";
+ drive-strength = <12>;
+ bias-pull-down;
+ output-high;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
+ ports-implemented = <0x1>;
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+
+ pinctrl-0 = <&usb0_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&usb3_1 {
+ status = "okay";
+
+ pinctrl-0 = <&usb1_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&pcie0 {
+ status = "okay";
+ reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+};
+
+&pcie1 {
+ status = "okay";
+ reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+ force_gen1 = <1>;
+};
+
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcadata@0 {
+ label = "qcadata";
+ reg = <0x0000000 0x0c80000>;
+ read-only;
+ };
+
+ APPSBL@c80000 {
+ label = "APPSBL";
+ reg = <0x0c80000 0x0500000>;
+ read-only;
+ };
+
+ APPSBLENV@1180000 {
+ label = "APPSBLENV";
+ reg = <0x1180000 0x0080000>;
+ read-only;
+ };
+
+ art: art@1200000 {
+ label = "art";
+ reg = <0x1200000 0x0140000>;
+ read-only;
+ };
+
+ artbak: art@1340000 {
+ label = "artbak";
+ reg = <0x1340000 0x0140000>;
+ read-only;
+ };
+
+ kernel@1480000 {
+ label = "kernel";
+ reg = <0x1480000 0x0400000>;
+ };
+
+ ubi@1880000 {
+ label = "ubi";
+ reg = <0x1880000 0x1C00000>;
+ };
+
+ netgear@3480000 {
+ label = "netgear";
+ reg = <0x3480000 0x4480000>;
+ read-only;
+ };
+
+ reserve@7900000 {
+ label = "reserve";
+ reg = <0x7900000 0x0700000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&phy4>;
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&art 6>;
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&art 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
&adm_dma {
status = "okay";
};
};
soc {
- pinmux@800000 {
- i2c4_pins: i2c4_pinmux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- bias-disable;
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- drive-strength = <10>;
- bias-none;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- rgmii0_pins: rgmii0_pins {
- mux {
- pins = "gpio2", "gpio66";
- drive-strength = <8>;
- bias-disable;
- };
- };
- };
-
- gsbi2: gsbi@12480000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- uart2: serial@12490000 {
- status = "okay";
- };
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi4: spi@1a280000 {
- status = "okay";
- spi-max-frequency = <50000000>;
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 0>;
-
- m25p80@0 {
- compatible = "s25fl256s1";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
- m25p,fast-read;
-
- partition@0 {
- label = "lowlevel_init";
- reg = <0x0 0x1b0000>;
- };
-
- partition@1 {
- label = "u-boot";
- reg = <0x1b0000 0x80000>;
- };
-
- partition@2 {
- label = "u-boot-env";
- reg = <0x230000 0x40000>;
- };
-
- partition@3 {
- label = "caldata";
- reg = <0x270000 0x40000>;
- };
-
- partition@4 {
- label = "firmware";
- reg = <0x2b0000 0x1d50000>;
- };
- };
- };
- };
-
- sata-phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- status = "okay";
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- };
-
- pcie2: pci@1b900000 {
- status = "okay";
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <7>;
};
};
+ };
+};
- gmac0: ethernet@37000000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <0>;
- phy-handle = <&phy4>;
+&qcom_pinmux {
+ i2c4_pins: i2c4_pinmux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ bias-disable;
+ };
- pinctrl-0 = <&rgmii0_pins>;
- pinctrl-names = "default";
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
};
+ };
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <1>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
};
+ };
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
- phy-handle = <&phy6>;
+ rgmii0_pins: rgmii0_pins {
+ mux {
+ pins = "gpio2", "gpio66";
+ drive-strength = <8>;
+ bias-disable;
};
+ };
+};
+
+&gsbi2 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ uart2: serial@12490000 {
+ status = "okay";
+ };
+};
+
+&gsbi5 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "okay";
+
+ spi4: spi@1a280000 {
+ status = "okay";
+ spi-max-frequency = <50000000>;
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 0>;
+
+ m25p80@0 {
+ compatible = "s25fl256s1";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ m25p,fast-read;
+
+ partition@0 {
+ label = "lowlevel_init";
+ reg = <0x0 0x1b0000>;
+ };
+
+ partition@1 {
+ label = "u-boot";
+ reg = <0x1b0000 0x80000>;
+ };
+
+ partition@2 {
+ label = "u-boot-env";
+ reg = <0x230000 0x40000>;
+ };
+
+ partition@3 {
+ label = "caldata";
+ reg = <0x270000 0x40000>;
+ };
- gmac3: ethernet@37600000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <3>;
- phy-handle = <&phy7>;
+ partition@4 {
+ label = "firmware";
+ reg = <0x2b0000 0x1d50000>;
+ };
};
};
};
+
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&pcie2 {
+ status = "okay";
+};
+
+&gmac0 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <0>;
+ phy-handle = <&phy4>;
+
+ pinctrl-0 = <&rgmii0_pins>;
+ pinctrl-names = "default";
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <1>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ phy-handle = <&phy6>;
+};
+
+&gmac3 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <3>;
+ phy-handle = <&phy7>;
+};
\ No newline at end of file
};
soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio65", "gpio67", "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio6", "gpio53", "gpio54";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- nand_pins: nand_pins {
- disable {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
-
- pullups {
- pins = "gpio39";
- function = "nand";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-bus-hold;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- status = "okay";
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- force_gen1 = <1>;
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- };
-
- pcie2: pci@1b900000 {
- status = "okay";
- };
-
- nand-controller@1ac00000 {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0000000 0x0040000>;
- read-only;
- };
-
- MIBIB@40000 {
- label = "MIBIB";
- reg = <0x0040000 0x0140000>;
- read-only;
- };
-
- SBL2@180000 {
- label = "SBL2";
- reg = <0x0180000 0x0140000>;
- read-only;
- };
-
- SBL3@2c0000 {
- label = "SBL3";
- reg = <0x02c0000 0x0280000>;
- read-only;
- };
-
- DDRCONFIG@540000 {
- label = "DDRCONFIG";
- reg = <0x0540000 0x0120000>;
- read-only;
- };
-
- SSD@660000 {
- label = "SSD";
- reg = <0x0660000 0x0120000>;
- read-only;
- };
-
- TZ@780000 {
- label = "TZ";
- reg = <0x0780000 0x0280000>;
- read-only;
- };
-
- RPM@a00000 {
- label = "RPM";
- reg = <0x0a00000 0x0280000>;
- read-only;
- };
-
- art: art@c80000 {
- label = "art";
- reg = <0x0c80000 0x0140000>;
- read-only;
- };
-
- APPSBL@dc0000 {
- label = "APPSBL";
- reg = <0x0dc0000 0x0100000>;
- read-only;
- };
-
- u_env@ec0000 {
- label = "u_env";
- reg = <0x0ec0000 0x0040000>;
- };
-
- s_env@f00000 {
- label = "s_env";
- reg = <0x0f00000 0x0040000>;
- };
-
- devinfo@f40000 {
- label = "devinfo";
- reg = <0x0f40000 0x0040000>;
- };
-
- linux@f80000 {
- label = "kernel1";
- reg = <0x0f80000 0x2800000>; /* 3 MB spill to rootfs*/
- };
-
- rootfs@1280000 {
- label = "rootfs1";
- reg = <0x1280000 0x2500000>;
- };
-
- linux2@3780000 {
- label = "kernel2";
- reg = <0x3780000 0x2800000>;
- };
-
- rootfs2@3a80000 {
- label = "rootfs2";
- reg = <0x3a80000 0x2500000>;
- };
-
- syscfg@5f80000 {
- label = "syscfg";
- reg = <0x5f80000 0x2080000>;
- };
- };
- };
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
};
};
-
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
- qcom,phy_mdio_addr = <4>;
- qcom,poll_required = <1>;
- qcom,rgmii_delay = <0>;
- qcom,emulation = <0>;
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- //lan
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
- qcom,phy_mdio_addr = <0>; /* none */
- qcom,poll_required = <0>; /* no polling */
- qcom,rgmii_delay = <0>;
- qcom,emulation = <0>;
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- adm_dma: dma@18300000 {
- status = "okay";
- };
};
keys {
};
};
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio65", "gpio67", "gpio68";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio6", "gpio53", "gpio54";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ disable {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ pullups {
+ pins = "gpio39";
+ function = "nand";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-bus-hold;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&pcie2 {
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0000000 0x0040000>;
+ read-only;
+ };
+
+ MIBIB@40000 {
+ label = "MIBIB";
+ reg = <0x0040000 0x0140000>;
+ read-only;
+ };
+
+ SBL2@180000 {
+ label = "SBL2";
+ reg = <0x0180000 0x0140000>;
+ read-only;
+ };
+
+ SBL3@2c0000 {
+ label = "SBL3";
+ reg = <0x02c0000 0x0280000>;
+ read-only;
+ };
+
+ DDRCONFIG@540000 {
+ label = "DDRCONFIG";
+ reg = <0x0540000 0x0120000>;
+ read-only;
+ };
+
+ SSD@660000 {
+ label = "SSD";
+ reg = <0x0660000 0x0120000>;
+ read-only;
+ };
+
+ TZ@780000 {
+ label = "TZ";
+ reg = <0x0780000 0x0280000>;
+ read-only;
+ };
+
+ RPM@a00000 {
+ label = "RPM";
+ reg = <0x0a00000 0x0280000>;
+ read-only;
+ };
+
+ art: art@c80000 {
+ label = "art";
+ reg = <0x0c80000 0x0140000>;
+ read-only;
+ };
+
+ APPSBL@dc0000 {
+ label = "APPSBL";
+ reg = <0x0dc0000 0x0100000>;
+ read-only;
+ };
+
+ u_env@ec0000 {
+ label = "u_env";
+ reg = <0x0ec0000 0x0040000>;
+ };
+
+ s_env@f00000 {
+ label = "s_env";
+ reg = <0x0f00000 0x0040000>;
+ };
+
+ devinfo@f40000 {
+ label = "devinfo";
+ reg = <0x0f40000 0x0040000>;
+ };
+
+ linux@f80000 {
+ label = "kernel1";
+ reg = <0x0f80000 0x2800000>; /* 3 MB spill to rootfs*/
+ };
+
+ rootfs@1280000 {
+ label = "rootfs1";
+ reg = <0x1280000 0x2500000>;
+ };
+
+ linux2@3780000 {
+ label = "kernel2";
+ reg = <0x3780000 0x2800000>;
+ };
+
+ rootfs2@3a80000 {
+ label = "rootfs2";
+ reg = <0x3a80000 0x2500000>;
+ };
+
+ syscfg@5f80000 {
+ label = "syscfg";
+ reg = <0x5f80000 0x2080000>;
+ };
+ };
+ };
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,rgmii_delay = <0>;
+ qcom,emulation = <0>;
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+/* LAN */
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ qcom,phy_mdio_addr = <0>; /* none */
+ qcom,poll_required = <0>; /* no polling */
+ qcom,rgmii_delay = <0>;
+ qcom,emulation = <0>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&adm_dma {
+ status = "okay";
+};
};
soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- nand_pins: nand_pins {
- disable {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
-
- pullups {
- pins = "gpio39";
- function = "nand";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-bus-hold;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- status = "okay";
- };
-
- usb3_0: usb3@110f8800 {
- clocks = <&gcc USB30_1_MASTER_CLK>;
- status = "okay";
- };
-
- usb3_1: usb3@100f8800 {
- clocks = <&gcc USB30_0_MASTER_CLK>;
- status = "okay";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- force_gen1 = <1>;
- };
-
- nand-controller@1ac00000 {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
- };
-
- kernel@1340000 {
- label = "kernel";
- reg = <0x1340000 0x0400000>;
- };
-
- ubi@1740000 {
- label = "ubi";
- reg = <0x1740000 0x1600000>;
- };
-
- netgear@2d40000 {
- label = "netgear";
- reg = <0x2d40000 0x0c00000>;
- read-only;
- };
-
- reserve@3940000 {
- label = "reserve";
- reg = <0x3940000 0x46c0000>;
- read-only;
- };
- };
- };
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
};
};
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
};
keys {
};
};
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+ "gpio24","gpio26", "gpio53", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ disable {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ pullups {
+ pins = "gpio39";
+ function = "nand";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-bus-hold;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&usb3_0 {
+ clocks = <&gcc USB30_1_MASTER_CLK>;
+ status = "okay";
+};
+
+&usb3_1 {
+ clocks = <&gcc USB30_0_MASTER_CLK>;
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcadata@0 {
+ label = "qcadata";
+ reg = <0x0000000 0x0c80000>;
+ read-only;
+ };
+
+ APPSBL@c80000 {
+ label = "APPSBL";
+ reg = <0x0c80000 0x0500000>;
+ read-only;
+ };
+
+ APPSBLENV@1180000 {
+ label = "APPSBLENV";
+ reg = <0x1180000 0x0080000>;
+ read-only;
+ };
+
+ art: art@1200000 {
+ label = "art";
+ reg = <0x1200000 0x0140000>;
+ read-only;
+ };
+
+ kernel@1340000 {
+ label = "kernel";
+ reg = <0x1340000 0x0400000>;
+ };
+
+ ubi@1740000 {
+ label = "ubi";
+ reg = <0x1740000 0x1600000>;
+ };
+
+ netgear@2d40000 {
+ label = "netgear";
+ reg = <0x2d40000 0x0c00000>;
+ read-only;
+ };
+
+ reserve@3940000 {
+ label = "reserve";
+ reg = <0x3940000 0x46c0000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&art 6>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&art 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
&tcsr {
qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
compatible = "qcom,tcsr";
};
soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- nand_pins: nand_pins {
- disable {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
-
- pullups {
- pins = "gpio39";
- function = "nand";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-bus-hold;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- status = "okay";
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- force_gen1 = <1>;
- };
-
- nand-controller@1ac00000 {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
- };
-
- artbak: art@1340000 {
- label = "artbak";
- reg = <0x1340000 0x0140000>;
- read-only;
- };
-
- kernel@1480000 {
- label = "kernel";
- reg = <0x1480000 0x0400000>;
- };
-
- ubi@1880000 {
- label = "ubi";
- reg = <0x1880000 0x6080000>;
- };
-
- reserve@7900000 {
- label = "reserve";
- reg = <0x7900000 0x0700000>;
- read-only;
- };
- };
- };
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
};
};
-
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
};
keys {
&adm_dma {
status = "okay";
};
+
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+ "gpio24","gpio26", "gpio53", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ disable {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ pullups {
+ pins = "gpio39";
+ function = "nand";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-bus-hold;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ usb0_pwr_en_pins: usb0_pwr_en_pins {
+ mux {
+ pins = "gpio15";
+ function = "gpio";
+ drive-strength = <12>;
+ bias-pull-down;
+ output-high;
+ };
+ };
+
+ usb1_pwr_en_pins: usb1_pwr_en_pins {
+ mux {
+ pins = "gpio16", "gpio68";
+ function = "gpio";
+ drive-strength = <12>;
+ bias-pull-down;
+ output-high;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+
+ pinctrl-0 = <&usb0_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&usb3_1 {
+ status = "okay";
+
+ pinctrl-0 = <&usb1_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&pcie0 {
+ status = "okay";
+ reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+};
+
+&pcie1 {
+ status = "okay";
+ reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+ force_gen1 = <1>;
+};
+
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcadata@0 {
+ label = "qcadata";
+ reg = <0x0000000 0x0c80000>;
+ read-only;
+ };
+
+ APPSBL@c80000 {
+ label = "APPSBL";
+ reg = <0x0c80000 0x0500000>;
+ read-only;
+ };
+
+ APPSBLENV@1180000 {
+ label = "APPSBLENV";
+ reg = <0x1180000 0x0080000>;
+ read-only;
+ };
+
+ art: art@1200000 {
+ label = "art";
+ reg = <0x1200000 0x0140000>;
+ read-only;
+ };
+
+ artbak: art@1340000 {
+ label = "artbak";
+ reg = <0x1340000 0x0140000>;
+ read-only;
+ };
+
+ kernel@1480000 {
+ label = "kernel";
+ reg = <0x1480000 0x0400000>;
+ };
+
+ ubi@1880000 {
+ label = "ubi";
+ reg = <0x1880000 0x6080000>;
+ };
+
+ reserve@7900000 {
+ label = "reserve";
+ reg = <0x7900000 0x0700000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&art 6>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&art 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
\ No newline at end of file
};
soc {
- pinmux@800000 {
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
- "gpio26", "gpio53", "gpio56", "gpio66";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi4: spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- W25Q128@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- MIBIB@20000 {
- label = "MIBIB";
- reg = <0x20000 0x20000>;
- read-only;
- };
-
- SBL2@40000 {
- label = "SBL2";
- reg = <0x40000 0x40000>;
- read-only;
- };
-
- SBL3@80000 {
- label = "SBL3";
- reg = <0x80000 0x80000>;
- read-only;
- };
-
- DDRCONFIG@100000 {
- label = "DDRCONFIG";
- reg = <0x100000 0x10000>;
- read-only;
- };
-
- SSD@110000 {
- label = "SSD";
- reg = <0x110000 0x10000>;
- read-only;
- };
-
- TZ@120000 {
- label = "TZ";
- reg = <0x120000 0x80000>;
- read-only;
- };
-
- RPM@1a0000 {
- label = "RPM";
- reg = <0x1a0000 0x80000>;
- read-only;
- };
-
- APPSBL@220000 {
- label = "APPSBL";
- reg = <0x220000 0x80000>;
- read-only;
- };
-
- APPSBLENV@2a0000 {
- label = "APPSBLENV";
- reg = <0x2a0000 0x40000>;
- read-only;
- };
-
- OLDART@2e0000 {
- label = "OLDART";
- reg = <0x2e0000 0x40000>;
- read-only;
- };
-
- kernel@320000 {
- label = "kernel";
- reg = <0x320000 0x300000>;
- };
-
- rootfs@620000 {
- label = "rootfs";
- reg = <0x620000 0x960000>;
- };
-
- defaultmac: default-mac@0xfaf100 {
- label = "default-mac";
- reg = <0xfaf100 0x00200>;
- read-only;
- };
-
- ART@fc0000 {
- label = "ART";
- reg = <0xfc0000 0x40000>;
- read-only;
- };
- };
- };
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- force_gen1 = <1>;
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
};
};
-
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&defaultmac 0>;
- mtd-mac-address-increment = <1>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&defaultmac 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
};
keys {
};
};
+&qcom_pinmux {
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
+ "gpio26", "gpio53", "gpio56", "gpio66";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ button_pins: button_pins {
+ mux {
+ pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ bias-pull-down;
+ };
+
+ data {
+ pins = "gpio18", "gpio19";
+ drive-strength = <10>;
+ };
+
+ cs {
+ pins = "gpio20";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ clk {
+ pins = "gpio21";
+ drive-strength = <12>;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&gsbi5 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "okay";
+
+ spi4: spi@1a280000 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ W25Q128@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ MIBIB@20000 {
+ label = "MIBIB";
+ reg = <0x20000 0x20000>;
+ read-only;
+ };
+
+ SBL2@40000 {
+ label = "SBL2";
+ reg = <0x40000 0x40000>;
+ read-only;
+ };
+
+ SBL3@80000 {
+ label = "SBL3";
+ reg = <0x80000 0x80000>;
+ read-only;
+ };
+
+ DDRCONFIG@100000 {
+ label = "DDRCONFIG";
+ reg = <0x100000 0x10000>;
+ read-only;
+ };
+
+ SSD@110000 {
+ label = "SSD";
+ reg = <0x110000 0x10000>;
+ read-only;
+ };
+
+ TZ@120000 {
+ label = "TZ";
+ reg = <0x120000 0x80000>;
+ read-only;
+ };
+
+ RPM@1a0000 {
+ label = "RPM";
+ reg = <0x1a0000 0x80000>;
+ read-only;
+ };
+
+ APPSBL@220000 {
+ label = "APPSBL";
+ reg = <0x220000 0x80000>;
+ read-only;
+ };
+
+ APPSBLENV@2a0000 {
+ label = "APPSBLENV";
+ reg = <0x2a0000 0x40000>;
+ read-only;
+ };
+
+ OLDART@2e0000 {
+ label = "OLDART";
+ reg = <0x2e0000 0x40000>;
+ read-only;
+ };
+
+ kernel@320000 {
+ label = "kernel";
+ reg = <0x320000 0x300000>;
+ };
+
+ rootfs@620000 {
+ label = "rootfs";
+ reg = <0x620000 0x960000>;
+ };
+
+ defaultmac: default-mac@0xfaf100 {
+ label = "default-mac";
+ reg = <0xfaf100 0x00200>;
+ read-only;
+ };
+
+ ART@fc0000 {
+ label = "ART";
+ reg = <0xfc0000 0x40000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&defaultmac 0>;
+ mtd-mac-address-increment = <1>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&defaultmac 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
&adm_dma {
status = "okay";
};
};
soc {
- rpm@108000 {
- pinctrl-0 = <&rpm_pins>;
- pinctrl-names = "default";
- };
- nand-controller@1ac00000 {
- status = "okay";
+ mdio0: mdio@37000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
+ compatible = "qcom,ipq8064-mdio", "syscon";
+ reg = <0x37000000 0x200000>;
+ resets = <&gcc GMAC_CORE1_RESET>;
+ reset-names = "stmmaceth";
+ clocks = <&gcc GMAC_CORE1_CLK>;
+ clock-names = "stmmaceth";
- mt29f2g08abbeah4@0 {
- compatible = "qcom,nandcs";
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+ ethernet-phy@0 {
reg = <0>;
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0000000 0x0040000>;
- read-only;
- };
-
- MIBIB@40000 {
- label = "MIBIB";
- reg = <0x0040000 0x0140000>;
- read-only;
- };
-
- SBL2@180000 {
- label = "SBL2";
- reg = <0x0180000 0x0140000>;
- read-only;
- };
-
- SBL3@2c0000 {
- label = "SBL3";
- reg = <0x02c0000 0x0280000>;
- read-only;
- };
-
- DDRCONFIG@540000 {
- label = "DDRCONFIG";
- reg = <0x0540000 0x0120000>;
- read-only;
- };
-
- SSD@660000 {
- label = "SSD";
- reg = <0x0660000 0x0120000>;
- read-only;
- };
-
- TZ@780000 {
- label = "TZ";
- reg = <0x0780000 0x0280000>;
- read-only;
- };
-
- RPM@a00000 {
- label = "RPM";
- reg = <0x0a00000 0x0280000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- };
-
- ART@1200000 {
- label = "ART";
- reg = <0x1200000 0x0140000>;
- };
-
- ubi@1340000 {
- label = "ubi";
- reg = <0x1340000 0x4000000>;
- };
-
- BOOTCONFIG@5340000 {
- label = "BOOTCONFIG";
- reg = <0x5340000 0x0060000>;
- };
-
- SBL2-1@53a0000- {
- label = "SBL2_1";
- reg = <0x53a0000 0x0140000>;
- read-only;
- };
-
- SBL3-1@54e0000 {
- label = "SBL3_1";
- reg = <0x54e0000 0x0280000>;
- read-only;
- };
-
- DDRCONFIG-1@5760000 {
- label = "DDRCONFIG_1";
- reg = <0x5760000 0x0120000>;
- read-only;
- };
-
- SSD-1@5880000 {
- label = "SSD_1";
- reg = <0x5880000 0x0120000>;
- read-only;
- };
-
- TZ-1@59a0000 {
- label = "TZ_1";
- reg = <0x59a0000 0x0280000>;
- read-only;
- };
-
- RPM-1@5c20000 {
- label = "RPM_1";
- reg = <0x5c20000 0x0280000>;
- read-only;
- };
-
- BOOTCONFIG1@5ea0000 {
- label = "BOOTCONFIG1";
- reg = <0x5ea0000 0x0060000>;
- };
-
- APPSBL-1@5f00000 {
- label = "APPSBL_1";
- reg = <0x5f00000 0x0500000>;
- read-only;
- };
-
- ubi-1@6400000 {
- label = "ubi_1";
- reg = <0x6400000 0x4000000>;
- };
-
- unused@a400000 {
- label = "unused";
- reg = <0xa400000 0x5c00000>;
- };
- };
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
};
- };
- };
-
- mdio0: mdio@37000000 {
- #address-cells = <1>;
- #size-cells = <0>;
-
- compatible = "qcom,ipq8064-mdio", "syscon";
- reg = <0x37000000 0x200000>;
- resets = <&gcc GMAC_CORE1_RESET>;
- reset-names = "stmmaceth";
- clocks = <&gcc GMAC_CORE1_CLK>;
- clock-names = "stmmaceth";
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- ethernet-phy@0 {
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
+ ethernet-phy@4 {
+ reg = <4>;
+ };
};
- ethernet-phy@4 {
- reg = <4>;
- };
};
leds {
};
};
+&rpm {
+ pinctrl-0 = <&rpm_pins>;
+ pinctrl-names = "default";
+};
+
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ mt29f2g08abbeah4@0 {
+ compatible = "qcom,nandcs";
+
+ reg = <0>;
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0000000 0x0040000>;
+ read-only;
+ };
+
+ MIBIB@40000 {
+ label = "MIBIB";
+ reg = <0x0040000 0x0140000>;
+ read-only;
+ };
+
+ SBL2@180000 {
+ label = "SBL2";
+ reg = <0x0180000 0x0140000>;
+ read-only;
+ };
+
+ SBL3@2c0000 {
+ label = "SBL3";
+ reg = <0x02c0000 0x0280000>;
+ read-only;
+ };
+
+ DDRCONFIG@540000 {
+ label = "DDRCONFIG";
+ reg = <0x0540000 0x0120000>;
+ read-only;
+ };
+
+ SSD@660000 {
+ label = "SSD";
+ reg = <0x0660000 0x0120000>;
+ read-only;
+ };
+
+ TZ@780000 {
+ label = "TZ";
+ reg = <0x0780000 0x0280000>;
+ read-only;
+ };
+
+ RPM@a00000 {
+ label = "RPM";
+ reg = <0x0a00000 0x0280000>;
+ read-only;
+ };
+
+ APPSBL@c80000 {
+ label = "APPSBL";
+ reg = <0x0c80000 0x0500000>;
+ read-only;
+ };
+
+ APPSBLENV@1180000 {
+ label = "APPSBLENV";
+ reg = <0x1180000 0x0080000>;
+ };
+
+ ART@1200000 {
+ label = "ART";
+ reg = <0x1200000 0x0140000>;
+ };
+
+ ubi@1340000 {
+ label = "ubi";
+ reg = <0x1340000 0x4000000>;
+ };
+
+ BOOTCONFIG@5340000 {
+ label = "BOOTCONFIG";
+ reg = <0x5340000 0x0060000>;
+ };
+
+ SBL2-1@53a0000- {
+ label = "SBL2_1";
+ reg = <0x53a0000 0x0140000>;
+ read-only;
+ };
+
+ SBL3-1@54e0000 {
+ label = "SBL3_1";
+ reg = <0x54e0000 0x0280000>;
+ read-only;
+ };
+
+ DDRCONFIG-1@5760000 {
+ label = "DDRCONFIG_1";
+ reg = <0x5760000 0x0120000>;
+ read-only;
+ };
+
+ SSD-1@5880000 {
+ label = "SSD_1";
+ reg = <0x5880000 0x0120000>;
+ read-only;
+ };
+
+ TZ-1@59a0000 {
+ label = "TZ_1";
+ reg = <0x59a0000 0x0280000>;
+ read-only;
+ };
+
+ RPM-1@5c20000 {
+ label = "RPM_1";
+ reg = <0x5c20000 0x0280000>;
+ read-only;
+ };
+
+ BOOTCONFIG1@5ea0000 {
+ label = "BOOTCONFIG1";
+ reg = <0x5ea0000 0x0060000>;
+ };
+
+ APPSBL-1@5f00000 {
+ label = "APPSBL_1";
+ reg = <0x5f00000 0x0500000>;
+ read-only;
+ };
+
+ ubi-1@6400000 {
+ label = "ubi_1";
+ reg = <0x6400000 0x4000000>;
+ };
+
+ unused@a400000 {
+ label = "unused";
+ reg = <0xa400000 0x5c00000>;
+ };
+ };
+ };
+};
+
&adm_dma {
status = "okay";
};
status = "okay";
};
-
&usb3_1 {
status = "okay";
};
};
soc {
- nand-controller@1ac00000 {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- cs@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- ubi@0 {
- label = "ubi";
- reg = <0x0000000 0x4000000>;
- };
-
- rootfs_1@4000000 {
- label = "rootfs_1";
- reg = <0x4000000 0x4000000>;
- };
- };
- };
- };
mdio0: mdio@37000000 {
#address-cells = <1>;
};
};
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ cs@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ubi@0 {
+ label = "ubi";
+ reg = <0x0000000 0x4000000>;
+ };
+
+ rootfs_1@4000000 {
+ label = "rootfs_1";
+ reg = <0x4000000 0x4000000>;
+ };
+ };
+ };
+};
+
&adm_dma {
status = "okay";
};
};
};
- rpm@108000 {
+ rpm: rpm@108000 {
compatible = "qcom,rpm-ipq8064";
reg = <0x108000 0x1000>;
qcom,ipc = <&l2cc 0x8 2>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ack",
"err",
"wakeup";
leds_pins: leds_pins {
mux {
pins = "gpio7", "gpio8", "gpio9",
- "gpio26", "gpio53";
+ "gpio26", "gpio53";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
interrupt-controller;
#interrupt-cells = <3>;
reg = <0x02000000 0x1000>,
- <0x02002000 0x1000>;
+ <0x02002000 0x1000>;
};
timer@200a000 {
compatible = "qcom,kpss-timer", "qcom,msm-timer";
interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
+ <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
+ <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
+ <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_EDGE_RISING)>;
reg = <0x0200a000 0x100>;
clock-frequency = <25000000>,
uart2: serial@12490000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x12490000 0x1000>,
- <0x12480000 0x1000>;
+ <0x12480000 0x1000>;
interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
clock-names = "core", "iface";
gsbi4_serial: serial@16340000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16340000 0x1000>,
- <0x16300000 0x1000>;
+ <0x16300000 0x1000>;
interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
clock-names = "core", "iface";
uart5: serial@1a240000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x1a240000 0x1000>,
- <0x1a200000 0x1000>;
+ <0x1a200000 0x1000>;
interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
gsbi7_serial: serial@16640000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16640000 0x1000>,
- <0x16600000 0x1000>;
+ <0x16600000 0x1000>;
interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
clock-names = "core", "iface";
pcie0: pci@1b500000 {
compatible = "qcom,pcie-ipq8064";
reg = <0x1b500000 0x1000
- 0x1b502000 0x80
- 0x1b600000 0x100
- 0x0ff00000 0x100000>;
+ 0x1b502000 0x80
+ 0x1b600000 0x100
+ 0x0ff00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <0>;
pcie1: pci@1b700000 {
compatible = "qcom,pcie-ipq8064";
reg = <0x1b700000 0x1000
- 0x1b702000 0x80
- 0x1b800000 0x100
- 0x31f00000 0x100000>;
+ 0x1b702000 0x80
+ 0x1b800000 0x100
+ 0x31f00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <1>;
pcie2: pci@1b900000 {
compatible = "qcom,pcie-ipq8064";
reg = <0x1b900000 0x1000
- 0x1b902000 0x80
- 0x1ba00000 0x100
- 0x35f00000 0x100000>;
+ 0x1b902000 0x80
+ 0x1ba00000 0x100
+ 0x35f00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <2>;
regulator-always-on;
};
- sdcc1bam:dma@12402000 {
+ sdcc1bam: dma@12402000 {
compatible = "qcom,bam-v1.3.0";
reg = <0x12402000 0x8000>;
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
- };
+ };
- sdcc3bam:dma@12182000 {
+ sdcc3bam: dma@12182000 {
compatible = "qcom,bam-v1.3.0";
reg = <0x12182000 0x8000>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
qcom,ee = <0>;
};
- amba {
+ amba: amba {
compatible = "arm,amba-bus";
#address-cells = <1>;
#size-cells = <1>;
};
soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio53", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio9", "gpio26", "gpio33", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
-
- clk {
- pins = "gpio1";
- input-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
-
- tx {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
- input-disable;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- drive-strength = <10>;
- bias-none;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <12>;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio17";
- function = "gpio";
- drive-strength = <12>;
- };
-
- pwr {
- pins = "gpio17";
- bias-pull-down;
- output-high;
- };
-
- ovc {
- pins = "gpio16";
- bias-pull-up;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio14", "gpio15";
- function = "gpio";
- drive-strength = <12>;
- };
-
- pwr {
- pins = "gpio14";
- bias-pull-down;
- output-high;
- };
-
- ovc {
- pins = "gpio15";
- bias-pull-up;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi4: spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- m25p80@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <51200000>;
- reg = <0>;
-
- partitions {
- compatible = "qcom,smem";
- };
- };
- };
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- force_gen1 = <1>;
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = <&mdio0_pins>;
pinctrl-names = "default";
+
phy0: ethernet-phy@0 {
reg = <0>;
qca,ar8327-initvals = <
>;
};
};
-
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
- qcom,phy_mdio_addr = <4>;
- qcom,poll_required = <0>;
- qcom,rgmii_delay = <1>;
- qcom,phy_mii_type = <0>;
- qcom,emulation = <0>;
- qcom,irq = <255>;
- mdiobus = <&mdio0>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
- qcom,phy_mdio_addr = <0>; /* none */
- qcom,poll_required = <0>; /* no polling */
- qcom,rgmii_delay = <0>;
- qcom,phy_mii_type = <1>;
- qcom,emulation = <0>;
- qcom,irq = <258>;
- mdiobus = <&mdio0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- amba {
- sdcc1: sdcc@12400000 {
- status = "okay";
- };
- };
};
keys {
};
};
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio53", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio9", "gpio26", "gpio33", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ clk {
+ pins = "gpio1";
+ input-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ tx {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
+ input-disable;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+
+ cs {
+ pins = "gpio20";
+ drive-strength = <12>;
+ };
+ };
+
+ usb0_pwr_en_pins: usb0_pwr_en_pins {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "gpio";
+ drive-strength = <12>;
+ };
+
+ pwr {
+ pins = "gpio17";
+ bias-pull-down;
+ output-high;
+ };
+
+ ovc {
+ pins = "gpio16";
+ bias-pull-up;
+ };
+ };
+
+ usb1_pwr_en_pins: usb1_pwr_en_pins {
+ mux {
+ pins = "gpio14", "gpio15";
+ function = "gpio";
+ drive-strength = <12>;
+ };
+
+ pwr {
+ pins = "gpio14";
+ bias-pull-down;
+ output-high;
+ };
+
+ ovc {
+ pins = "gpio15";
+ bias-pull-up;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&gsbi5 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "okay";
+
+ spi4: spi@1a280000 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ m25p80@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <51200000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "qcom,smem";
+ };
+ };
+ };
+};
+
+&usb3_0 {
+ status = "okay";
+
+ pinctrl-0 = <&usb0_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&usb3_1 {
+ status = "okay";
+
+ pinctrl-0 = <&usb1_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&pcie0 {
+ status = "okay";
+ reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+};
+
+&pcie1 {
+ status = "okay";
+ reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+ force_gen1 = <1>;
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <0>;
+ qcom,rgmii_delay = <1>;
+ qcom,phy_mii_type = <0>;
+ qcom,emulation = <0>;
+ qcom,irq = <255>;
+ mdiobus = <&mdio0>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ qcom,phy_mdio_addr = <0>; /* none */
+ qcom,poll_required = <0>; /* no polling */
+ qcom,rgmii_delay = <0>;
+ qcom,phy_mii_type = <1>;
+ qcom,emulation = <0>;
+ qcom,irq = <258>;
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&amba {
+ sdcc1: sdcc@12400000 {
+ status = "okay";
+ };
+};
+
&adm_dma {
status = "okay";
};
};
soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
- };
-
- nand_pins: nand_pins {
- disable {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
-
- pullups {
- pins = "gpio39";
- function = "nand";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-bus-hold;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
-
- clk {
- pins = "gpio1";
- input-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
-
- tx {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
- input-disable;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- spi6_pins: spi6_pins {
- mux {
- pins = "gpio55", "gpio56", "gpio58";
- function = "gsbi6";
- bias-pull-down;
- };
-
- mosi {
- pins = "gpio55";
- drive-strength = <12>;
- };
-
- miso {
- pins = "gpio56";
- drive-strength = <14>;
- };
-
- cs {
- pins = "gpio57";
- drive-strength = <12>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio58";
- drive-strength = <12>;
- };
-
- reset {
- pins = "gpio33";
- drive-strength = <10>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- ports-implemented = <0x1>;
- status = "okay";
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0046";
- reg = <0x00010000 0 0 0 0>;
-
- mtd-mac-address = <&art 6>;
- mtd-mac-address-increment = <(1)>;
- };
- };
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- force_gen1 = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0046";
- reg = <0x00010000 0 0 0 0>;
-
- mtd-mac-address = <&art 6>;
- mtd-mac-address-increment = <(2)>;
- };
- };
- };
-
- nand-controller@1ac00000 {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
- };
-
- artbak: art@1340000 {
- label = "artbak";
- reg = <0x1340000 0x0140000>;
- read-only;
- };
-
- kernel@1480000 {
- label = "kernel";
- reg = <0x1480000 0x0400000>;
- };
-
- ubi@1880000 {
- label = "ubi";
- reg = <0x1880000 0x6080000>;
- };
-
- reserve@7900000 {
- label = "reserve";
- reg = <0x7900000 0x0700000>;
- read-only;
- };
- };
- };
- };
-
mdio0: mdio@37000000 {
#address-cells = <1>;
#size-cells = <0>;
>;
};
};
-
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
- qcom,phy_mdio_addr = <4>;
- qcom,poll_required = <0>;
- qcom,rgmii_delay = <1>;
- qcom,phy_mii_type = <0>;
- qcom,emulation = <0>;
- qcom,irq = <255>;
- mdiobus = <&mdio0>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
- qcom,phy_mdio_addr = <0>; /* none */
- qcom,poll_required = <0>; /* no polling */
- qcom,rgmii_delay = <0>;
- qcom,phy_mii_type = <1>;
- qcom,emulation = <0>;
- qcom,irq = <258>;
- mdiobus = <&mdio0>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
};
keys {
};
};
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+ "gpio24","gpio26", "gpio53", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ nand_pins: nand_pins {
+ disable {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ pullups {
+ pins = "gpio39";
+ function = "nand";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-bus-hold;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ clk {
+ pins = "gpio1";
+ input-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ tx {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
+ input-disable;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ bias-pull-down;
+ };
+
+ data {
+ pins = "gpio18", "gpio19";
+ drive-strength = <10>;
+ };
+
+ cs {
+ pins = "gpio20";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ clk {
+ pins = "gpio21";
+ drive-strength = <12>;
+ };
+ };
+
+ spi6_pins: spi6_pins {
+ mux {
+ pins = "gpio55", "gpio56", "gpio58";
+ function = "gsbi6";
+ bias-pull-down;
+ };
+
+ mosi {
+ pins = "gpio55";
+ drive-strength = <12>;
+ };
+
+ miso {
+ pins = "gpio56";
+ drive-strength = <14>;
+ };
+
+ cs {
+ pins = "gpio57";
+ drive-strength = <12>;
+ bias-pull-up;
+ };
+
+ clk {
+ pins = "gpio58";
+ drive-strength = <12>;
+ };
+
+ reset {
+ pins = "gpio33";
+ drive-strength = <10>;
+ bias-pull-down;
+ output-high;
+ };
+ };
+
+ usb0_pwr_en_pins: usb0_pwr_en_pins {
+ mux {
+ pins = "gpio15";
+ function = "gpio";
+ drive-strength = <12>;
+ bias-pull-down;
+ output-high;
+ };
+ };
+
+ usb1_pwr_en_pins: usb1_pwr_en_pins {
+ mux {
+ pins = "gpio16", "gpio68";
+ function = "gpio";
+ drive-strength = <12>;
+ bias-pull-down;
+ output-high;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+
+ serial@16340000 {
+ status = "okay";
+ };
+
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcadata@0 {
+ label = "qcadata";
+ reg = <0x0000000 0x0c80000>;
+ read-only;
+ };
+
+ APPSBL@c80000 {
+ label = "APPSBL";
+ reg = <0x0c80000 0x0500000>;
+ read-only;
+ };
+
+ APPSBLENV@1180000 {
+ label = "APPSBLENV";
+ reg = <0x1180000 0x0080000>;
+ read-only;
+ };
+
+ art: art@1200000 {
+ label = "art";
+ reg = <0x1200000 0x0140000>;
+ read-only;
+ };
+
+ artbak: art@1340000 {
+ label = "artbak";
+ reg = <0x1340000 0x0140000>;
+ read-only;
+ };
+
+ kernel@1480000 {
+ label = "kernel";
+ reg = <0x1480000 0x0400000>;
+ };
+
+ ubi@1880000 {
+ label = "ubi";
+ reg = <0x1880000 0x6080000>;
+ };
+
+ reserve@7900000 {
+ label = "reserve";
+ reg = <0x7900000 0x0700000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <0>;
+ qcom,rgmii_delay = <1>;
+ qcom,phy_mii_type = <0>;
+ qcom,emulation = <0>;
+ qcom,irq = <255>;
+ mdiobus = <&mdio0>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&art 6>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ qcom,phy_mdio_addr = <0>; /* none */
+ qcom,poll_required = <0>; /* no polling */
+ qcom,rgmii_delay = <0>;
+ qcom,phy_mii_type = <1>;
+ qcom,emulation = <0>;
+ qcom,irq = <258>;
+ mdiobus = <&mdio0>;
+
+ mtd-mac-address = <&art 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
&adm_dma {
status = "okay";
};
+
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
+ ports-implemented = <0x1>;
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+
+ pinctrl-0 = <&usb0_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&usb3_1 {
+ status = "okay";
+
+ pinctrl-0 = <&usb1_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&pcie0 {
+ status = "okay";
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi@1,0 {
+ compatible = "pci168c,0046";
+ reg = <0x00010000 0 0 0 0>;
+
+ mtd-mac-address = <&art 6>;
+ mtd-mac-address-increment = <(1)>;
+ };
+ };
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi@1,0 {
+ compatible = "pci168c,0046";
+ reg = <0x00010000 0 0 0 0>;
+
+ mtd-mac-address = <&art 6>;
+ mtd-mac-address-increment = <(2)>;
+ };
+ };
+};
projects / openwrt / staging / jow.git / commitdiff