uboot-mediatek: add support for JDCloud RE-CP-03

The vendor U-Boot has enabled signature verification, so add
a custom U-Boot build for OpenWrt.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 6fa4fbbc5293886aa6bae6e0cac4b99a4c472fc4)

diff --git a/package/boot/uboot-mediatek/Makefile b/package/boot/uboot-mediatek/Makefile
index 7fdad5c744833f9b642ba707881ff25e7cbadbc9..a15b88ec5e87ddf34f84e07529d6009f9c104ccc 100644 (file)
--- a/package/boot/uboot-mediatek/Makefile
+++ b/package/boot/uboot-mediatek/Makefile
@@ -417,6 +417,18 @@ define U-Boot/mt7986_glinet_gl-mt6000
   DEPENDS:=+trusted-firmware-a-mt7986-emmc-ddr4
 endef
 
+define U-Boot/mt7986_jdcloud_re-cp-03
+  NAME:=JDCloud RE-CP-03
+  BUILD_SUBTARGET:=filogic
+  BUILD_DEVICES:=jdcloud_re-cp-03
+  UBOOT_CONFIG:=mt7986a_jdcloud_re-cp-03
+  UBOOT_IMAGE:=u-boot.fip
+  BL2_BOOTDEV:=emmc
+  BL2_SOC:=mt7986
+  BL2_DDRTYPE:=ddr4
+  DEPENDS:=+trusted-firmware-a-mt7986-emmc-ddr4
+endef
+
 define U-Boot/mt7986_tplink_tl-xdr4288
   NAME:=TP-LINK TL-XDR4288
   BUILD_SUBTARGET:=filogic
@@ -573,6 +585,7 @@ UBOOT_TARGETS := \
        mt7986_bananapi_bpi-r3-snand \
        mt7986_bananapi_bpi-r3-nor \
        mt7986_glinet_gl-mt6000 \
+       mt7986_jdcloud_re-cp-03 \
        mt7986_tplink_tl-xdr4288 \
        mt7986_tplink_tl-xdr6086 \
        mt7986_tplink_tl-xdr6088 \

diff --git a/package/boot/uboot-mediatek/patches/440-add-jdcloud_re-cp-03.patch b/package/boot/uboot-mediatek/patches/440-add-jdcloud_re-cp-03.patch
new file mode 100644 (file)
index 0000000..e0f3a6e
--- /dev/null
+++ b/package/boot/uboot-mediatek/patches/440-add-jdcloud_re-cp-03.patch
@@ -0,0 +1,324 @@
+--- /dev/null
++++ b/configs/mt7986a_jdcloud_re-cp-03_defconfig
+@@ -0,0 +1,112 @@
++CONFIG_ARM=y
++CONFIG_SYS_HAS_NONCACHED_MEMORY=y
++CONFIG_POSITION_INDEPENDENT=y
++CONFIG_ARCH_MEDIATEK=y
++CONFIG_TEXT_BASE=0x41e00000
++CONFIG_SYS_MALLOC_F_LEN=0x4000
++CONFIG_NR_DRAM_BANKS=1
++CONFIG_ENV_SIZE=0x40000
++CONFIG_ENV_OFFSET=0x400000
++CONFIG_DEFAULT_DEVICE_TREE="mt7986a-jdcloud_re-cp-03"
++CONFIG_SYS_PROMPT="MT7986> "
++CONFIG_OF_LIBFDT_OVERLAY=y
++CONFIG_TARGET_MT7986=y
++CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
++CONFIG_DEBUG_UART_BASE=0x11002000
++CONFIG_DEBUG_UART_CLOCK=40000000
++CONFIG_ENV_OFFSET_REDUND=0x440000
++CONFIG_SYS_LOAD_ADDR=0x46000000
++CONFIG_DEBUG_UART=y
++CONFIG_FIT=y
++CONFIG_BOOTDELAY=30
++CONFIG_AUTOBOOT_KEYED=y
++CONFIG_AUTOBOOT_MENU_SHOW=y
++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7986a-jdcloud_re-cp-03.dtb"
++CONFIG_LOGLEVEL=7
++CONFIG_PRE_CONSOLE_BUFFER=y
++CONFIG_LOG=y
++CONFIG_BOARD_LATE_INIT=y
++CONFIG_HUSH_PARSER=y
++CONFIG_CMD_CPU=y
++CONFIG_CMD_LICENSE=y
++CONFIG_CMD_BOOTMENU=y
++CONFIG_CMD_ASKENV=y
++CONFIG_CMD_ERASEENV=y
++CONFIG_CMD_ENV_FLAGS=y
++CONFIG_CMD_STRINGS=y
++CONFIG_CMD_DM=y
++CONFIG_CMD_GPIO=y
++CONFIG_CMD_PWM=y
++CONFIG_CMD_GPT=y
++CONFIG_CMD_MMC=y
++CONFIG_CMD_PART=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_TFTPSRV=y
++CONFIG_CMD_RARP=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_CDP=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_LINK_LOCAL=y
++CONFIG_CMD_PXE=y
++CONFIG_CMD_CACHE=y
++CONFIG_CMD_PSTORE=y
++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
++CONFIG_CMD_UUID=y
++CONFIG_CMD_HASH=y
++CONFIG_CMD_SMC=y
++CONFIG_CMD_EXT4=y
++CONFIG_CMD_FAT=y
++CONFIG_CMD_FS_GENERIC=y
++CONFIG_CMD_FS_UUID=y
++CONFIG_OF_EMBED=y
++CONFIG_ENV_OVERWRITE=y
++CONFIG_ENV_IS_IN_MMC=y
++CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
++CONFIG_SYS_RELOC_GD_ENV_ADDR=y
++CONFIG_USE_DEFAULT_ENV_FILE=y
++CONFIG_DEFAULT_ENV_FILE="jdcloud_re-cp-03_env"
++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
++CONFIG_VERSION_VARIABLE=y
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_NETCONSOLE=y
++CONFIG_USE_IPADDR=y
++CONFIG_IPADDR="192.168.1.1"
++CONFIG_USE_SERVERIP=y
++CONFIG_SERVERIP="192.168.1.254"
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_BUTTON=y
++CONFIG_BUTTON_GPIO=y
++CONFIG_CLK=y
++CONFIG_GPIO_HOG=y
++CONFIG_LED=y
++CONFIG_LED_BLINK=y
++CONFIG_LED_GPIO=y
++CONFIG_SUPPORT_EMMC_BOOT=y
++CONFIG_MMC_HS200_SUPPORT=y
++CONFIG_MMC_MTK=y
++CONFIG_PHY_FIXED=y
++CONFIG_DM_MDIO=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PHY=y
++CONFIG_PHY_MTK_TPHY=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7622=y
++CONFIG_PINCTRL_MT7986=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_REGULATOR_GPIO=y
++CONFIG_DM_PWM=y
++CONFIG_PWM_MTK=y
++CONFIG_RAM=y
++CONFIG_SCSI=y
++CONFIG_DM_SCSI=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_ZSTD=y
++CONFIG_HEXDUMP=y
++CONFIG_LMB_MAX_REGIONS=64
+--- /dev/null
++++ b/arch/arm/dts/mt7986a-jdcloud_re-cp-03.dts
+@@ -0,0 +1,148 @@
++// SPDX-License-Identifier: GPL-2.0-or-later
++
++/dts-v1/;
++#include <dt-bindings/input/linux-event-codes.h>
++#include "mt7986.dtsi"
++#include <dt-bindings/gpio/gpio.h>
++
++/ {
++      #address-cells = <1>;
++      #size-cells = <1>;
++      model = "JDCloud RE-CP-03";
++      compatible = "mediatek,mt7986", "mediatek,mt7986-rfb";
++
++      chosen {
++              stdout-path = &uart0;
++              tick-timer = &timer0;
++      };
++
++      memory@40000000 {
++              device_type = "memory";
++              reg = <0x40000000 0x40000000>;
++      };
++
++      gpio-keys {
++              compatible = "gpio-keys";
++
++              button-joylink {
++                      label = "joylink";
++                      linux,code = <BTN_0>;
++                      gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
++              };
++
++              button-reset {
++                      label = "reset";
++                      linux,code = <KEY_RESTART>;
++                      gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
++              };
++      };
++
++      gpio-leds {
++              compatible = "gpio-leds";
++
++              led-0 {
++                      label = "blue:status";
++                      gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
++                      default-state = "off";
++              };
++
++              led-1 {
++                      label = "red:status";
++                      gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
++                      default-state = "on";
++              };
++
++              led-2 {
++                      label = "green:status";
++                      gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
++                      default-state = "off";
++              };
++      };
++
++      reg_1p8v: regulator-1p8v {
++              compatible = "regulator-fixed";
++              regulator-name = "fixed-1.8V";
++              regulator-min-microvolt = <1800000>;
++              regulator-max-microvolt = <1800000>;
++              regulator-boot-on;
++              regulator-always-on;
++      };
++
++      reg_3p3v: regulator-3p3v {
++              compatible = "regulator-fixed";
++              regulator-name = "fixed-3.3V";
++              regulator-min-microvolt = <3300000>;
++              regulator-max-microvolt = <3300000>;
++              regulator-boot-on;
++              regulator-always-on;
++      };
++};
++
++&eth {
++      status = "okay";
++      mediatek,gmac-id = <0>;
++      phy-mode = "2500base-x";
++      mediatek,switch = "mt7531";
++      reset-gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
++
++      fixed-link {
++              speed = <2500>;
++              full-duplex;
++      };
++};
++
++&mmc0 {
++      bus-width = <8>;
++      cap-mmc-highspeed;
++      cap-mmc-hw-reset;
++      max-frequency = <200000000>;
++      non-removable;
++      pinctrl-names = "default";
++      pinctrl-0 = <&mmc0_pins_default>;
++      vmmc-supply = <&reg_3p3v>;
++      vqmmc-supply = <&reg_1p8v>;
++      status = "okay";
++};
++
++&pinctrl {
++      mmc0_pins_default: mmc0default {
++              mux {
++                      function = "flash";
++                      groups =  "emmc_51";
++              };
++
++              conf-cmd-dat {
++                      pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
++                             "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
++                             "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
++                      input-enable;
++                      drive-strength = <MTK_DRIVE_4mA>;
++                      bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
++              };
++
++              conf-clk {
++                      pins = "EMMC_CK";
++                      drive-strength = <MTK_DRIVE_6mA>;
++                      bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
++              };
++
++              conf-dsl {
++                      pins = "EMMC_DSL";
++                      bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
++              };
++
++              conf-rst {
++                      pins = "EMMC_RSTB";
++                      drive-strength = <MTK_DRIVE_4mA>;
++                      bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
++              };
++      };
++};
++
++&uart0 {
++      status = "okay";
++};
++
++&watchdog {
++      status = "disabled";
++};
+--- /dev/null
++++ b/jdcloud_re-cp-03_env
+@@ -0,0 +1,55 @@
++ipaddr=192.168.1.1
++serverip=192.168.1.254
++loadaddr=0x46000000
++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
++bootargs=root=/dev/mmcblk0p65
++bootcmd=if pstore check ; then run boot_recovery ; else run boot_emmc ; fi
++bootconf=config-1
++bootdelay=0
++bootfile=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb
++bootfile_bl2=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin
++bootfile_fip=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip
++bootfile_upg=openwrt-mediatek-filogic-jdcloud_re-cp-03-squashfs-sysupgrade.itb
++bootled_pwr=red:status
++bootled_rec=blue:status
++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
++bootmenu_default=0
++bootmenu_delay=0
++bootmenu_title=      \e[0;34m( ( ( \e[1;39mOpenWrt\e[0;34m ) ) )
++bootmenu_0=Initialize environment.=run _firstboot
++bootmenu_0d=Run default boot command.=run boot_default
++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
++bootmenu_2=Boot production system from eMMC.=run boot_production ; run bootmenu_confirm_return
++bootmenu_3=Boot recovery system from eMMC.=run boot_recovery ; run bootmenu_confirm_return
++bootmenu_4=Load production system via TFTP then write to eMMC.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_5=Load recovery system via TFTP then write to eMMC.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_6=\e[31mLoad BL31+U-Boot FIP via TFTP then write to eMMC.\e[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
++bootmenu_7=\e[31mLoad BL2 preloader via TFTP then write to eMMC.\e[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
++bootmenu_8=Reboot.=reset
++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
++boot_production=led $bootled_pwr on ; run emmc_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
++boot_recovery=led $bootled_rec on ; run emmc_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
++boot_emmc=run boot_production ; run boot_recovery
++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
++boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run emmc_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run emmc_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run emmc_write_fip
++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run emmc_write_bl2
++boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
++mmc_write_vol=imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc erase 0x$part_addr 0x$image_size && mmc write $loadaddr 0x$part_addr 0x$image_size
++mmc_read_vol=mmc read $loadaddr $part_addr 0x100 && imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc read $loadaddr 0x$part_addr 0x$image_size && setexpr filesize $image_size * 0x200
++part_default=production
++part_recovery=recovery
++reset_factory=eraseenv && reset
++emmc_read_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_read_vol
++emmc_read_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_read_vol
++emmc_write_bl2=mmc partconf 0 1 1 1 && mmc erase 0x0 0x400 && mmc write $fileaddr 0x0 0x400 ; mmc partconf 0 1 1 0
++emmc_write_fip=mmc erase 0x3400 0x2000 && mmc write $fileaddr 0x3400 0x2000 && mmc erase 0x2000 0x800
++emmc_write_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_write_vol
++emmc_write_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_write_vol
++_init_env=setenv _init_env ; setenv _create_env ; saveenv ; saveenv
++_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title       \e[33m$ver\e[0m"