ARM: mach-imx: move early resume code out of the .data section

Building the kernel with allyesconfig fails because the i.mx early
resume code located in the .data section is unable to fixup the bl
relocation as the branch target gets too far away.

The idea of having code in the .data section allows for easy access to
nearby data using relative addressing while the MMU is off. However it
is probably best to move the code back to the .text section where it
belongs and fixup the data access instead.  This solves the bl reloc
issue (at least until this becomes a general problem) and simplifies
the code as well.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S
index 921fc15558549093f0ff0bbcc9b9de946d520152..a58c8b0527ccb3aad1f542b83a159c868a61655d 100644 (file)
--- a/arch/arm/mach-imx/headsmp.S
+++ b/arch/arm/mach-imx/headsmp.S
@@ -26,16 +26,16 @@ ENDPROC(v7_secondary_startup)
 
 #ifdef CONFIG_PM
 /*
- * The following code is located into the .data section.  This is to
- * allow phys_l2x0_saved_regs to be accessed with a relative load
- * as we are running on physical address here.
+ * The following code must assume it is running from physical address
+ * where absolute virtual addresses to the data section have to be
+ * turned into relative ones.
  */
-       .data
-       .align
 
 #ifdef CONFIG_CACHE_L2X0
        .macro  pl310_resume
-       ldr     r2, phys_l2x0_saved_regs
+       adr     r0, l2x0_saved_regs_offset
+       ldr     r2, [r0]
+       add     r2, r2, r0
        ldr     r0, [r2, #L2X0_R_PHY_BASE]      @ get physical base of l2x0
        ldr     r1, [r2, #L2X0_R_AUX_CTRL]      @ get aux_ctrl value
        str     r1, [r0, #L2X0_AUX_CTRL]        @ restore aux_ctrl
@@ -43,9 +43,9 @@ ENDPROC(v7_secondary_startup)
        str     r1, [r0, #L2X0_CTRL]            @ re-enable L2
        .endm
 
-       .globl  phys_l2x0_saved_regs
-phys_l2x0_saved_regs:
-        .long   0
+l2x0_saved_regs_offset:
+       .word   l2x0_saved_regs - .
+
 #else
        .macro  pl310_resume
        .endm

diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c
index ee42d20cba19f022d4a9ece8616e27b443d7e82e..5faba7a3c95f6e74393699045aa0635331459d46 100644 (file)
--- a/arch/arm/mach-imx/pm-imx6q.c
+++ b/arch/arm/mach-imx/pm-imx6q.c
@@ -22,8 +22,6 @@
 #include "common.h"
 #include "hardware.h"
 
-extern unsigned long phys_l2x0_saved_regs;
-
 static int imx6q_suspend_finish(unsigned long val)
 {
        cpu_do_idle();
@@ -57,18 +55,5 @@ static const struct platform_suspend_ops imx6q_pm_ops = {
 
 void __init imx6q_pm_init(void)
 {
-       /*
-        * The l2x0 core code provides an infrastucture to save and restore
-        * l2x0 registers across suspend/resume cycle.  But because imx6q
-        * retains L2 content during suspend and needs to resume L2 before
-        * MMU is enabled, it can only utilize register saving support and
-        * have to take care of restoring on its own.  So we save physical
-        * address of the data structure used by l2x0 core to save registers,
-        * and later restore the necessary ones in imx6q resume entry.
-        */
-#ifdef CONFIG_CACHE_L2X0
-       phys_l2x0_saved_regs = __pa(&l2x0_saved_regs);
-#endif
-
        suspend_set_ops(&imx6q_pm_ops);
 }