ipq40xx: ipq4019: Add new device Compex WPJ419
authorDaniel Danzberger <daniel@dd-wrt.com>
Fri, 1 Nov 2019 11:27:13 +0000 (12:27 +0100)
committerJohn Crispin <john@phrozen.org>
Sat, 2 Nov 2019 18:25:15 +0000 (19:25 +0100)
This device contains 2 flash devices. One NOR (32M) and one NAND (128M).
U-boot and caldata are on the NOR, the firmware on the NAND.

    SoC:    IPQ4019
    CPU:    4x 710MHz ARMv7
    RAM:    256MB
    FLASH:  NOR:32MB NAND:128MB
    ETH:    2x GMAC Gigabit
    POE:    802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V)
    WIFI:   1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO
            1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO
    USB:    1x 3.0
    PCI:    1x Mini PCIe
    SIM:    1x Slot
    SD:     1x MicroSD slot
    BTN:    Reset
    LED:    - Power
            - Ethernet
    UART:  1x Serial Port 4 Pin Connector (UART)
           1x Serial Port 6 Pin Connector (High Speed UART)
    POWER: 12V 2A

Installation
------------
Initial flashing can only be done via u-boot using the following commands:

tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi
nand erase.chip; nand write ${fileaddr} 0x0 ${filesize}
res

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
target/linux/ipq40xx/base-files/etc/board.d/02_network
target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts [new file with mode: 0644]
target/linux/ipq40xx/image/Makefile
target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch

index 25402b7eb4fec0832114751d8a7e7e0f36efd558..dafd83234ee97ed8384b060e2220b9f57b7fd350 100755 (executable)
@@ -48,6 +48,7 @@ ipq40xx_setup_interfaces()
                ucidef_set_interface_lan "eth0"
                ;;
        avm,fritzrepeater-3000|\
+       compex,wpj419|\
        compex,wpj428)
                ucidef_set_interface_lan "eth0 eth1"
                ;;
index 2336ef3c7ba62d1670aeb568c63ccac216502261..d4e4cc49ec8bb3f067bfb6eba013639c69669ba7 100644 (file)
@@ -70,6 +70,7 @@ case "$FIRMWARE" in
                /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
                /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
                ;;
+       compex,wpj419 |\
        compex,wpj428 |\
        engenius,eap1300 |\
        openmesh,a42 |\
@@ -133,6 +134,7 @@ case "$FIRMWARE" in
                /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
                /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
                ;;
+       compex,wpj419 |\
        compex,wpj428 |\
        engenius,eap1300 |\
        openmesh,a42 |\
index 3445f2b50f718c15e3d80845b5aa78666ec3ff79..96f865c67e3249834f01bab1953de8c588b73eb3 100644 (file)
@@ -73,6 +73,9 @@ platform_do_upgrade() {
                CI_KERNPART="linux"
                nand_do_upgrade "$1"
                ;;
+       compex,wpj419)
+               nand_do_upgrade "$1"
+               ;;
        linksys,ea6350v3 |\
        linksys,ea8300)
                platform_do_upgrade_linksys "$1"
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts
new file mode 100644 (file)
index 0000000..b6eb992
--- /dev/null
@@ -0,0 +1,374 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Nguyen Dinh Phi <phi_nguyen@compex.com.sg>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+       model = "Compex WPJ419";
+       compatible = "compex,wpj419", "qcom,ipq4019";
+
+       memory {
+               device_type = "memory";
+               reg = <0x80000000 0x10000000>;
+       };
+
+       reserved-memory {
+               ranges;
+               rsvd1@87000000 {
+                       /* Reserved for other subsystem */
+                       reg = <0x87000000 0x500000>;
+                       no-map;
+               };
+               wifi_dump@87500000 {
+                       reg = <0x87500000 0x600000>;
+                       no-map;
+               };
+
+               rsvd2@87B00000 {
+                       /* Reserved for other subsystem */
+                       reg = <0x87B00000 0x500000>;
+                       no-map;
+               };
+       };
+
+       chosen {
+               bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1 clk_ignore_unused";
+       };
+
+       soc {
+               pinctrl@1000000 {
+                       mdio_pins: mdio_pinmux {
+                               mux_1 {
+                                       pins = "gpio6";
+                                       function = "mdio";
+                                       bias-pull-up;
+                               };
+
+                               mux_2 {
+                                       pins = "gpio7";
+                                       function = "mdc";
+                                       bias-pull-up;
+                               };
+                       };
+
+                       serial_0_pins: serial_pinmux {
+                               mux {
+                                       pins = "gpio16", "gpio17";
+                                       function = "blsp_uart0";
+                                       bias-disable;
+                               };
+                       };
+
+                       serial_1_pins: serial1_pinmux {
+                               mux {
+                                       pins = "gpio8", "gpio9", "gpio10", "gpio11";
+                                       function = "blsp_uart1";
+                                       bias-disable;
+                               };
+                       };
+
+                       spi_0_pins: spi_0_pinmux {
+                               pinmux {
+                                       function = "blsp_spi0";
+                                       pins = "gpio13", "gpio14", "gpio15";
+                                       bias-disable;
+                               };
+
+                               pinmux_cs {
+                                       function = "gpio";
+                                       pins = "gpio12";
+                                       bias-disable;
+                                       output-high;
+                               };
+                       };
+
+                       i2c_0_pins: i2c_0_pinmux {
+                               mux {
+                                       pins = "gpio20", "gpio21";
+                                       function = "blsp_i2c0";
+                                       bias-disable;
+                               };
+                       };
+
+                       nand_pins: nand_pins {
+                               pullups {
+                                       pins = "gpio52", "gpio53", "gpio58", "gpio59";
+                                       function = "qpic";
+                                       bias-pull-up;
+                               };
+
+                               pulldowns {
+                                       pins = "gpio54", "gpio55", "gpio56",
+                                       "gpio57", "gpio60", "gpio61",
+                                       "gpio62", "gpio63", "gpio64",
+                                       "gpio65", "gpio66", "gpio67",
+                                       "gpio68", "gpio69";
+                                       function = "qpic";
+                                       bias-pull-down;
+                               };
+                       };
+
+                       led_0_pins: led0_pinmux {
+                               mux_1 {
+                                       pins = "gpio36";
+                                       function = "led0";
+                                       bias-pull-down;
+                               };
+                               mux_2 {
+                                       pins = "gpio40";
+                                       function = "led4";
+                                       bias-pull-down;
+                               };
+                       };
+               };
+
+               blsp_dma: dma@7884000 {
+                       status = "okay";
+               };
+
+               spi_0: spi@78b5000 {
+                       pinctrl-0 = <&spi_0_pins>;
+                       pinctrl-names = "default";
+                       status = "okay";
+                       cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, <&tlmm 41 GPIO_ACTIVE_HIGH>;
+                       num-cs = <2>;
+
+                       flash0@0 {
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+                               reg = <0>;
+                               compatible = "jedec,spi-nor";
+                               spi-max-frequency = <24000000>;
+                               broken-flash-reset;
+
+                               partitions {
+                                       compatible = "fixed-partitions";
+
+                                       partition@0 {
+                                               label = "0:SBL1";
+                                               reg = <0x000000 0x040000>;
+                                               read-only;
+                                       };
+
+                                       partition@40000 {
+                                               label = "0:MIBIB";
+                                               reg = <0x040000 0x020000>;
+                                               read-only;
+                                       };
+
+                                       partition@60000 {
+                                               label = "0:QSEE";
+                                               reg = <0x060000 0x060000>;
+                                               read-only;
+                                       };
+
+                                       partition@c0000 {
+                                               label = "0:CDT";
+                                               reg = <0x0c0000 0x010000>;
+                                               read-only;
+                                       };
+
+                                       partition@d0000 {
+                                               label = "0:DDRPARAMS";
+                                               reg = <0x0d0000 0x010000>;
+                                               read-only;
+                                       };
+
+                                       partition@e0000 {
+                                               label = "u-boot-env";
+                                               reg = <0x0e0000 0x010000>;
+                                       };
+
+                                       partition@f0000 {
+                                               label = "u-boot";
+                                               reg = <0x0f0000 0x080000>;
+                                               read-only;
+                                       };
+
+                                       partition@170000 {
+                                               label = "0:ART";
+                                               reg = <0x170000 0x010000>;
+                                               read-only;
+                                       };
+                               };
+                       };
+
+                       nand@1 {
+                               reg = <1>;
+                               status = "okay";
+                               compatible = "spi-nand";
+                               spi-max-frequency = <24000000>;
+
+                               partitions {
+                                       compatible = "fixed-partitions";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+
+                                       /* The device has 128MB, but we can only address
+                                        * 64MB because of the bootloader's default settings.
+                                        * This is due to the old mt29f driver,
+                                        * which detected the deivce with only 64MB
+                                        */
+                                       partition@0 {
+                                               label = "ubi";
+                                               reg = <0x0000000 0x4000000>;
+                                       };
+                               };
+                       };
+               };
+
+               mdio@90000 {
+                       status = "okay";
+                       phy-reset-gpio = <&tlmm 47 0>;
+                       pinctrl-0 = <&mdio_pins>;
+                       pinctrl-names = "default";
+               };
+
+               ess-psgmii@98000 {
+                       status = "okay";
+               };
+
+               tcsr@194b000 {
+                       /* select hostmode */
+                       compatible = "qcom,tcsr";
+                       reg = <0x194b000 0x100>;
+                       qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+                       status = "okay";
+               };
+
+               tcsr@1949000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1949000 0x100>;
+                       qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+               };
+
+               ess_tcsr@1953000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1953000 0x1000>;
+                       qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+               };
+
+               tcsr@1957000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1957000 0x100>;
+                       qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+               };
+
+               i2c_0: i2c@78b7000 {
+                       pinctrl-0 = <&i2c_0_pins>;
+                       pinctrl-names = "default";
+                       status = "ok";
+               };
+
+               serial@78af000 {
+                       pinctrl-0 = <&serial_0_pins>;
+                       pinctrl-names = "default";
+                       status = "okay";
+               };
+
+               serial@78b0000 {
+                       pinctrl-0 = <&serial_1_pins>;
+                       pinctrl-names = "default";
+                       status = "okay";
+               };
+
+               usb3_ss_phy: ssphy@9a000 {
+                       status = "okay";
+               };
+
+               usb3_hs_phy: hsphy@a6000 {
+                       status = "okay";
+               };
+
+               usb3: usb3@8af8800 {
+                       status = "okay";
+               };
+
+               usb2_hs_phy: hsphy@a8000 {
+                       status = "okay";
+               };
+
+               usb2: usb2@60f8800 {
+                       status = "okay";
+               };
+
+               cryptobam: dma@8e04000 {
+                       status = "okay";
+               };
+
+               crypto@8e3a000 {
+                       status = "okay";
+               };
+
+               watchdog@b017000 {
+                       status = "okay";
+               };
+
+               ess-switch@c000000 {
+                       switch_lan_bmp = <0x1e>;
+                       switch_wan_bmp = <0x20>;
+                       status = "okay";
+               };
+
+               edma@c080000 {
+                       status = "okay";
+               };
+
+               qpic_bam: dma@7984000 {
+                       status = "okay";
+               };
+
+               pcie0: pci@40000000 {
+                       status = "okay";
+                       perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+                       wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+               };
+
+               nand: qpic-nand@79b0000 {
+                       pinctrl-0 = <&nand_pins>;
+                       pinctrl-names = "default";
+                       status = "okay";
+               };
+       };
+};
+
+&gmac0 {
+       qcom,phy_mdio_addr = <4>;
+       qcom,poll_required = <1>;
+       qcom,forced_speed = <1000>;
+       qcom,forced_duplex = <1>;
+       vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+       qcom,phy_mdio_addr = <3>;
+       qcom,poll_required = <1>;
+       qcom,forced_speed = <1000>;
+       qcom,forced_duplex = <1>;
+       vlan_tag = <1 0x10>;
+};
+
+&wifi0 {
+       status = "okay";
+};
+
+&wifi1 {
+       status = "okay";
+};
index ed46bca6490b4e1fda2718720fb9bcf8975ce9a0..ef80e68393625fd4239ddf3cb993431cad83cc23 100644 (file)
@@ -164,6 +164,20 @@ define Device/avm_fritzrepeater-3000
 endef
 TARGET_DEVICES += avm_fritzrepeater-3000
 
+define Device/compex_wpj419
+       $(call Device/FitImage)
+       $(call Device/UbiFit)
+       DEVICE_VENDOR := Compex
+       DEVICE_MODEL := WPJ419
+       DEVICE_DTS := qcom-ipq4019-wpj419
+       DEVICE_DTS_CONFIG := config@12
+       KERNEL_INSTALL := 1
+       BLOCKSIZE := 128k
+       PAGESIZE := 2048
+       FILESYSTEMS := squashfs
+endef
+TARGET_DEVICES += compex_wpj419
+
 define Device/compex_wpj428
        $(call Device/FitImage)
        DEVICE_VENDOR := Compex
index 2fe6e46966430851d5a5a902198c56f14c57ee0e..4649b337e33b5fa67f8c7439edbd8a65963f67dc 100644 (file)
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,35 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,36 @@ dtb-$(CONFIG_ARCH_QCOM) += \
        qcom-apq8074-dragonboard.dtb \
        qcom-apq8084-ifc6540.dtb \
        qcom-apq8084-mtp.dtb \
@@ -40,6 +40,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +      qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
 +      qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
 +      qcom-ipq4019-unielec-u4019-32m.dtb \
++      qcom-ipq4019-wpj419.dtb \
 +      qcom-ipq4028-wpj428.dtb \
 +      qcom-ipq4029-gl-b1300.dtb \
 +      qcom-ipq4029-mr33.dtb \