--- /dev/null
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "TP-Link Archer VR2600v";
+ compatible = "tplink,vr2600v", "qcom,ipq8064";
+
+ memory@0 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &uart4;
+ mdio-gpio0 = &mdio0;
+
+ led-boot = &power;
+ led-failsafe = &general;
+ led-running = &power;
+ led-upgrade = &general;
+ };
+
+ chosen {
+ linux,stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ pinmux@800000 {
+ led_pins: led_pins {
+ pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
+ "gpio26", "gpio53", "gpio56", "gpio66";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ button_pins: button_pins {
+ pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ bias-pull-down;
+ };
+
+ data {
+ pins = "gpio18", "gpio19";
+ drive-strength = <10>;
+ };
+
+ cs {
+ pins = "gpio20";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ clk {
+ pins = "gpio21";
+ drive-strength = <12>;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+ };
+
+ gsbi5: gsbi@1a200000 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "ok";
+
+ spi4: spi@1a280000 {
+ status = "ok";
+ spi-max-frequency = <50000000>;
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ flash: W25Q128@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ MIBIB@20000 {
+ label = "MIBIB";
+ reg = <0x20000 0x20000>;
+ read-only;
+ };
+
+ SBL2@40000 {
+ label = "SBL2";
+ reg = <0x40000 0x40000>;
+ read-only;
+ };
+
+ SBL3@80000 {
+ label = "SBL3";
+ reg = <0x80000 0x80000>;
+ read-only;
+ };
+
+ DDRCONFIG@100000 {
+ label = "DDRCONFIG";
+ reg = <0x100000 0x10000>;
+ read-only;
+ };
+
+ SSD@110000 {
+ label = "SSD";
+ reg = <0x110000 0x10000>;
+ read-only;
+ };
+
+ TZ@120000 {
+ label = "TZ";
+ reg = <0x120000 0x80000>;
+ read-only;
+ };
+
+ RPM@1a0000 {
+ label = "RPM";
+ reg = <0x1a0000 0x80000>;
+ read-only;
+ };
+
+ APPSBL@220000 {
+ label = "APPSBL";
+ reg = <0x220000 0x80000>;
+ read-only;
+ };
+
+ APPSBLENV@2a0000 {
+ label = "APPSBLENV";
+ reg = <0x2a0000 0x40000>;
+ read-only;
+ };
+
+ OLDART@2e0000 {
+ label = "OLDART";
+ reg = <0x2e0000 0x40000>;
+ read-only;
+ };
+
+ kernel@320000 {
+ label = "kernel";
+ reg = <0x320000 0x200000>;
+ };
+
+ rootfs@520000 {
+ label = "rootfs";
+ reg = <0x520000 0xa60000>;
+ };
+
+ defaultmac: default-mac@0xfaf100 {
+ label = "default-mac";
+ reg = <0xfaf100 0x00200>;
+ read-only;
+ };
+
+ ART@fc0000 {
+ label = "ART";
+ reg = <0xfc0000 0x40000>;
+ read-only;
+ };
+
+ };
+ };
+ };
+
+ phy@100f8800 { /* USB3 port 1 HS phy */
+ status = "ok";
+ };
+
+ phy@100f8830 { /* USB3 port 1 SS phy */
+ status = "ok";
+ };
+
+ phy@110f8800 { /* USB3 port 0 HS phy */
+ status = "ok";
+ };
+
+ phy@110f8830 { /* USB3 port 0 SS phy */
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
+
+ pcie0: pci@1b500000 {
+ status = "ok";
+ phy-tx0-term-offset = <7>;
+ };
+
+ pcie1: pci@1b700000 {
+ status = "ok";
+ phy-tx0-term-offset = <7>;
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ reg = <4>;
+ };
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&defaultmac 0>;
+ mtd-mac-address-increment = <1>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&defaultmac 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ rpm@108000 {
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "default";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
+
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ dect {
+ label = "dect";
+ gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_PHONE>;
+ };
+
+ ledswitch {
+ label = "ledswitch";
+ gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_LIGHTS_TOGGLE>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ dsl {
+ label = "vr2600v:white:dsl";
+ gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb {
+ label = "vr2600v:white:usb";
+ gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan {
+ label = "vr2600v:white:lan";
+ gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan2g {
+ label = "vr2600v:white:wlan2g";
+ gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan5g {
+ label = "vr2600v:white:wlan5g";
+ gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
+ };
+
+ power: power {
+ label = "vr2600v:white:power";
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+ };
+
+ phone {
+ label = "vr2600v:white:phone";
+ gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan {
+ label = "vr2600v:white:wan";
+ gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
+ };
+
+ general: general {
+ label = "vr2600v:white:general";
+ gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&adm_dma {
+ status = "ok";
+};
projects / openwrt / staging / stintel.git / commitdiff