ath79: add support for TP-Link CPE710-v1

TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on the AP152 reference board

Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
  data rate) Based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal
  reflector
- Power, LAN, WLAN5G Blue LEDs
- 3x Blue LEDs

Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[convert to nvmem, fix MAC assignment in 11-ath10k-caldata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

diff --git a/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts b/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts
new file mode 100644 (file)
index 0000000..c97d165
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       model = "TP-Link CPE710 v1";
+       compatible = "tplink,cpe710-v1", "qca,qca9563";
+
+       aliases {
+               label-mac-device = &eth0;
+               led-boot = &led_lan;
+               led-failsafe = &led_lan;
+               led-upgrade = &led_lan;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_lan: lan {
+                       label = "blue:lan";
+                       gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+               };
+
+               wlan5g {
+                       label = "blue:wlan5g";
+                       gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "Reset button";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+       };
+};
+
+&pcie {
+       status = "okay";
+};
+
+&spi {
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <40000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x000000 0x040000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "u-boot-env";
+                               reg = <0x040000 0x010000>;
+                       };
+
+                       partition@50000 {
+                               label = "partition-table";
+                               reg = <0x050000 0x010000>;
+                               read-only;
+                       };
+
+                       info: partition@60000 {
+                               label = "info";
+                               reg = <0x060000 0x010000>;
+                               read-only;
+                       };
+
+                       partition@70000 {
+                               compatible = "denx,uimage";
+                               label = "firmware";
+                               reg = <0x070000 0xf50000>;
+                       };
+
+                       partition@fc0000 {
+                               label = "config";
+                               reg = <0xfc0000 0x030000>;
+                               read-only;
+                       };
+
+                       art: partition@ff0000 {
+                               label = "art";
+                               reg = <0xff0000 0x010000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&pinmux {
+       mdio_pins: mdio_pins {
+               /* GPIO 10 as MDIO(0x20), GPIO 8 as MDC(0x21) */
+               pinctrl-single,bits = <0x8 0x00200021 0x00ff00ff>;
+       };
+};
+
+&mdio0 {
+       status = "okay";
+
+       pinctrl-names = "default";
+       pinctrl-0 = <&mdio_pins>;
+
+       phy-mask = <0x10>;
+
+       phy4: ethernet-phy@4 {
+               reg = <4>;
+               reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+       };
+};
+
+&eth0 {
+       status = "okay";
+
+       phy-handle = <&phy4>;
+       phy-mode = "sgmii";
+
+       nvmem-cells = <&macaddr_info_8>;
+       nvmem-cell-names = "mac-address";
+
+       qca956x-serdes-fixup;
+
+       gmac-config {
+               device = <&gmac>;
+       };
+};
+
+&info {
+       compatible = "nvmem-cells";
+       #address-cells = <1>;
+       #size-cells = <1>;
+
+       macaddr_info_8: macaddr@8 {
+               reg = <0x8 0x6>;
+       };
+};

diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index ffc6f3086e1848cad50c4c0f7e557778fe725c1a..1c112b49521e6a1f94c5c37e82d03ae4b934b359 100644 (file)
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -169,7 +169,8 @@ enterasys,ws-ap3705i|\
 openmesh,mr900-v1|\
 openmesh,mr900-v2|\
 openmesh,mr1750-v1|\
-openmesh,mr1750-v2)
+openmesh,mr1750-v2|\
+tplink,cpe710-v1)
        ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0"
        ;;
 compex,wpj344-16m|\

diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index e2c6f9feac1950f611ceb2dd9c50ba50d8c4a412..af4cf08ce04cf96dadc34832e85760b4885e2270 100644 (file)
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -63,6 +63,7 @@ ath79_setup_interfaces()
        tplink,cpe510-v3|\
        tplink,cpe610-v1|\
        tplink,cpe610-v2|\
+       tplink,cpe710-v1|\
        tplink,eap225-outdoor-v1|\
        tplink,eap225-v3|\
        tplink,eap245-v1|\

diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 5ba1a7a8ffade8a9e4c9625e21023e4aafab4872..7f8c1b11431054bfd60e0fe0c951ba60ef2d5872 100644 (file)
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -236,6 +236,12 @@ case "$FIRMWARE" in
                ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
                        /lib/firmware/ath10k/QCA9888/hw2.0/board.bin
                ;;
+       tplink,cpe710-v1)
+               caldata_extract "art" 0x5000 0x2f20
+               ath10k_patch_mac $(mtd_get_mac_binary info 0x8)
+               ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+                       /lib/firmware/ath10k/QCA9888/hw2.0/board.bin
+               ;;
        tplink,eap225-outdoor-v1|\
        tplink,eap225-v3|\
        tplink,eap225-wall-v2|\

diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index b6755fe5478a9ef97cc20dececd2abbd0da7847f..363be289c65947e4e3d825682cabb5c369ae2f2d 100644 (file)
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -362,6 +362,17 @@ define Device/tplink_cpe610-v2
 endef
 TARGET_DEVICES += tplink_cpe610-v2
 
+define Device/tplink_cpe710-v1
+  $(Device/tplink-safeloader-uimage)
+  SOC := qca9563
+  IMAGE_SIZE := 15680k
+  DEVICE_MODEL := CPE710
+  DEVICE_VARIANT := v1
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+  TPLINK_BOARD_ID := CPE710V1
+endef
+TARGET_DEVICES += tplink_cpe710-v1
+
 define Device/tplink-eap2x5
   $(Device/tplink-safeloader)
   LOADER_TYPE := elf

diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c
index b20d1fdd30e0236c9f2c42e596807d01b92808cc..03329a392617442da926fda17519f1aec7a43ee7 100644 (file)
--- a/tools/firmware-utils/src/tplink-safeloader.c
+++ b/tools/firmware-utils/src/tplink-safeloader.c
@@ -534,6 +534,43 @@ static struct device_info boards[] = {
                .first_sysupgrade_partition = "os-image",
                .last_sysupgrade_partition = "support-list",
        },
+       /** Firmware layout for the CPE710 V1 */
+       {
+               .id     = "CPE710V1",
+               .vendor = "CPE710(TP-LINK|UN|AC866-5|00000000):1.0\r\n",
+               .support_list =
+                       "SupportList:\r\n"
+                       "CPE710(TP-LINK|UN|AC866-5|00000000):1.0\r\n"
+                       "CPE710(TP-LINK|EU|AC866-5|45550000):1.0\r\n"
+                       "CPE710(TP-LINK|US|AC866-5|55530000):1.0\r\n"
+                       "CPE710(TP-LINK|UN|AC866-5):1.0\r\n"
+                       "CPE710(TP-LINK|EU|AC866-5):1.0\r\n"
+                       "CPE710(TP-LINK|US|AC866-5):1.0\r\n",
+               .part_trail = 0xff,
+               .soft_ver = SOFT_VER_DEFAULT,
+
+               .partitions = {
+                       {"fs-uboot", 0x00000, 0x50000},
+                       {"partition-table", 0x50000, 0x02000},
+                       {"default-mac", 0x60000, 0x00020},
+                       {"serial-number", 0x60100, 0x00020},
+                       {"product-info", 0x61100, 0x00100},
+                       {"device-info", 0x61400, 0x00400},
+                       {"signature", 0x62000, 0x00400},
+                       {"device-id", 0x63000, 0x00100},
+                       {"firmware", 0x70000, 0xf40000},
+                       {"soft-version", 0xfb0000, 0x00100},
+                       {"support-list", 0xfb1000, 0x01000},
+                       {"user-config", 0xfc0000, 0x10000},
+                       {"default-config", 0xfd0000, 0x10000},
+                       {"log", 0xfe0000, 0x10000},
+                       {"radio", 0xff0000, 0x10000},
+                       {NULL, 0, 0}
+               },
+
+               .first_sysupgrade_partition = "os-image",
+               .last_sysupgrade_partition = "support-list",
+       },
 
        {
                .id     = "WBS210",