+++ /dev/null
-From cdcfd9211c805624a702b6ff81b9bd9515344749 Mon Sep 17 00:00:00 2001
-From: Andre Heider <a.heider@gmail.com>
-Date: Fri, 4 Sep 2020 16:34:22 +0200
-Subject: [PATCH] arm64: dts: armada-3720-espressobin: use Linux
- model/compatible strings
-
-Fix the actual board vendor and ease synching dts files from Linux.
-
-Signed-off-by: Andre Heider <a.heider@gmail.com>
----
- arch/arm/dts/armada-3720-espressobin.dts | 4 ++--
- board/Marvell/mvebu_armada-37xx/board.c | 8 ++++----
- 2 files changed, 6 insertions(+), 6 deletions(-)
-
---- a/arch/arm/dts/armada-3720-espressobin.dts
-+++ b/arch/arm/dts/armada-3720-espressobin.dts
-@@ -50,8 +50,8 @@
- #include "armada-372x.dtsi"
-
- / {
-- model = "Marvell Armada 3720 Community Board ESPRESSOBin";
-- compatible = "marvell,armada-3720-espressobin", "marvell,armada3720", "marvell,armada3710";
-+ model = "Globalscale Marvell ESPRESSOBin Board";
-+ compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710";
-
- chosen {
- stdout-path = "serial0:115200n8";
---- a/board/Marvell/mvebu_armada-37xx/board.c
-+++ b/board/Marvell/mvebu_armada-37xx/board.c
-@@ -88,14 +88,14 @@ int board_late_init(void)
- if (env_get("fdtfile"))
- return 0;
-
-- if (!of_machine_is_compatible("marvell,armada-3720-espressobin"))
-+ if (!of_machine_is_compatible("globalscale,espressobin"))
- return 0;
-
- /* If the memory controller has been configured for DDR4, we're running on v7 */
- ddr4 = ((readl(A3700_CH0_MC_CTRL2_REG) >> A3700_MC_CTRL2_SDRAM_TYPE_OFFS)
- & A3700_MC_CTRL2_SDRAM_TYPE_MASK) == A3700_MC_CTRL2_SDRAM_TYPE_DDR4;
-
-- emmc = of_machine_is_compatible("marvell,armada-3720-espressobin-emmc");
-+ emmc = of_machine_is_compatible("globalscale,espressobin-emmc");
-
- if (ddr4 && emmc)
- env_set("fdtfile", "marvell/armada-3720-espressobin-v7-emmc.dtb");
-@@ -248,7 +248,7 @@ static int mii_multi_chip_mode_write(str
- /* Bring-up board-specific network stuff */
- int board_network_enable(struct mii_dev *bus)
- {
-- if (!of_machine_is_compatible("marvell,armada-3720-espressobin"))
-+ if (!of_machine_is_compatible("globalscale,espressobin"))
- return 0;
-
- /*
-@@ -300,7 +300,7 @@ int ft_board_setup(void *blob, struct bd
- int part_off;
-
- /* Fill SPI MTD partitions for Linux kernel on Espressobin */
-- if (!of_machine_is_compatible("marvell,armada-3720-espressobin"))
-+ if (!of_machine_is_compatible("globalscale,espressobin"))
- return 0;
-
- spi_off = fdt_node_offset_by_compatible(blob, -1, "jedec,spi-nor");
+++ /dev/null
-From a9ac1dd46a4fd11880be80227e1eb102e3c61dd8 Mon Sep 17 00:00:00 2001
-From: Andre Heider <a.heider@gmail.com>
-Date: Fri, 4 Sep 2020 15:38:58 +0200
-Subject: [PATCH] arm64: dts: armada-3720-espressobin: split common parts
- to .dtsi
-
-Move most of the dts to the new common armada-3720-espressobin.dtsi
-file, just like Linux, but keep the current, downstream based, version.
-
-The dts itself is imported from Linux.
-
-Signed-off-by: Andre Heider <a.heider@gmail.com>
----
- arch/arm/dts/armada-3720-espressobin.dts | 164 +--------------------
- arch/arm/dts/armada-3720-espressobin.dtsi | 167 ++++++++++++++++++++++
- 2 files changed, 174 insertions(+), 157 deletions(-)
- create mode 100644 arch/arm/dts/armada-3720-espressobin.dtsi
-
---- a/arch/arm/dts/armada-3720-espressobin.dts
-+++ b/arch/arm/dts/armada-3720-espressobin.dts
-@@ -1,170 +1,20 @@
-+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
- /*
-- * Device Tree file for Marvell Armada 3720 community board
-- * (ESPRESSOBin)
-+ * Device Tree file for Globalscale Marvell ESPRESSOBin Board
- * Copyright (C) 2016 Marvell
- *
-- * Gregory CLEMENT <gregory.clement@free-electrons.com>
-- * Konstantin Porotchkin <kostap@marvell.com>
-+ * Romain Perier <romain.perier@free-electrons.com>
- *
-- * This file is dual-licensed: you can use it either under the terms
-- * of the GPL or the X11 license, at your option. Note that this dual
-- * licensing only applies to this file, and not this project as a
-- * whole.
-- *
-- * a) This file is free software; you can redistribute it and/or
-- * modify it under the terms of the GNU General Public License as
-- * published by the Free Software Foundation; either version 2 of the
-- * License, or (at your option) any later version.
-- *
-- * This file is distributed in the hope that it will be useful
-- * but WITHOUT ANY WARRANTY; without even the implied warranty of
-- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-- * GNU General Public License for more details.
-- *
-- * Or, alternatively
-- *
-- * b) Permission is hereby granted, free of charge, to any person
-- * obtaining a copy of this software and associated documentation
-- * files (the "Software"), to deal in the Software without
-- * restriction, including without limitation the rights to use
-- * copy, modify, merge, publish, distribute, sublicense, and/or
-- * sell copies of the Software, and to permit persons to whom the
-- * Software is furnished to do so, subject to the following
-- * conditions:
-- *
-- * The above copyright notice and this permission notice shall be
-- * included in all copies or substantial portions of the Software.
-- *
-- * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
-- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
-- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
-- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
-- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
-- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
-- * OTHER DEALINGS IN THE SOFTWARE.
-+ */
-+/*
-+ * Schematic available at http://espressobin.net/wp-content/uploads/2017/08/ESPRESSObin_V5_Schematics.pdf
- */
-
- /dts-v1/;
-
--#include "armada-372x.dtsi"
-+#include "armada-3720-espressobin.dtsi"
-
- / {
- model = "Globalscale Marvell ESPRESSOBin Board";
- compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710";
--
-- chosen {
-- stdout-path = "serial0:115200n8";
-- };
--
-- aliases {
-- ethernet0 = ð0;
-- i2c0 = &i2c0;
-- spi0 = &spi0;
-- };
--
-- memory {
-- device_type = "memory";
-- reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
-- };
--
-- vcc_sd_reg0: regulator@0 {
-- compatible = "regulator-gpio";
-- regulator-name = "vcc_sd0";
-- regulator-min-microvolt = <1800000>;
-- regulator-max-microvolt = <3300000>;
-- regulator-type = "voltage";
-- states = <1800000 0x1
-- 3300000 0x0>;
-- gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>;
-- };
--};
--
--&comphy {
-- max-lanes = <3>;
-- phy0 {
-- phy-type = <PHY_TYPE_USB3_HOST0>;
-- phy-speed = <PHY_SPEED_5G>;
-- };
--
-- phy1 {
-- phy-type = <PHY_TYPE_PEX0>;
-- phy-speed = <PHY_SPEED_2_5G>;
-- };
--
-- phy2 {
-- phy-type = <PHY_TYPE_SATA0>;
-- phy-speed = <PHY_SPEED_5G>;
-- };
--};
--
--ð0 {
-- status = "okay";
-- pinctrl-names = "default";
-- pinctrl-0 = <&rgmii_pins>, <&smi_pins>;
-- phy-mode = "rgmii";
-- phy_addr = <0x1>;
-- fixed-link {
-- speed = <1000>;
-- full-duplex;
-- };
--};
--
--&i2c0 {
-- pinctrl-names = "default";
-- pinctrl-0 = <&i2c1_pins>;
-- status = "okay";
--};
--
--/* CON3 */
--&sata {
-- status = "okay";
--};
--
--&sdhci0 {
-- pinctrl-names = "default";
-- pinctrl-0 = <&sdio_pins>;
-- bus-width = <4>;
-- cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>;
-- vqmmc-supply = <&vcc_sd_reg0>;
-- status = "okay";
--};
--
--&spi0 {
-- status = "okay";
-- pinctrl-names = "default";
-- pinctrl-0 = <&spi_quad_pins>;
--
-- spi-flash@0 {
-- #address-cells = <1>;
-- #size-cells = <1>;
-- compatible = "st,m25p128", "jedec,spi-nor";
-- reg = <0>; /* Chip select 0 */
-- spi-max-frequency = <50000000>;
-- m25p,fast-read;
-- };
--};
--
--/* Exported on the micro USB connector CON32 through an FTDI */
--&uart0 {
-- pinctrl-names = "default";
-- pinctrl-0 = <&uart1_pins>;
-- status = "okay";
--};
--
--/* CON29 */
--&usb2 {
-- status = "okay";
--};
--
--/* CON31 */
--&usb3 {
-- status = "okay";
--};
--
--&pcie0 {
-- pinctrl-names = "default";
-- pinctrl-0 = <&pcie_pins>;
-- reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
-- status = "okay";
- };
---- /dev/null
-+++ b/arch/arm/dts/armada-3720-espressobin.dtsi
-@@ -0,0 +1,167 @@
-+/*
-+ * Device Tree file for Marvell Armada 3720 community board
-+ * (ESPRESSOBin)
-+ * Copyright (C) 2016 Marvell
-+ *
-+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
-+ * Konstantin Porotchkin <kostap@marvell.com>
-+ *
-+ * This file is dual-licensed: you can use it either under the terms
-+ * of the GPL or the X11 license, at your option. Note that this dual
-+ * licensing only applies to this file, and not this project as a
-+ * whole.
-+ *
-+ * a) This file is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of the
-+ * License, or (at your option) any later version.
-+ *
-+ * This file is distributed in the hope that it will be useful
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * Or, alternatively
-+ *
-+ * b) Permission is hereby granted, free of charge, to any person
-+ * obtaining a copy of this software and associated documentation
-+ * files (the "Software"), to deal in the Software without
-+ * restriction, including without limitation the rights to use
-+ * copy, modify, merge, publish, distribute, sublicense, and/or
-+ * sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following
-+ * conditions:
-+ *
-+ * The above copyright notice and this permission notice shall be
-+ * included in all copies or substantial portions of the Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
-+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
-+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
-+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
-+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
-+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
-+ * OTHER DEALINGS IN THE SOFTWARE.
-+ */
-+
-+/dts-v1/;
-+
-+#include "armada-372x.dtsi"
-+
-+/ {
-+ chosen {
-+ stdout-path = "serial0:115200n8";
-+ };
-+
-+ aliases {
-+ ethernet0 = ð0;
-+ i2c0 = &i2c0;
-+ spi0 = &spi0;
-+ };
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
-+ };
-+
-+ vcc_sd_reg0: regulator@0 {
-+ compatible = "regulator-gpio";
-+ regulator-name = "vcc_sd0";
-+ regulator-min-microvolt = <1800000>;
-+ regulator-max-microvolt = <3300000>;
-+ regulator-type = "voltage";
-+ states = <1800000 0x1
-+ 3300000 0x0>;
-+ gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>;
-+ };
-+};
-+
-+&comphy {
-+ max-lanes = <3>;
-+ phy0 {
-+ phy-type = <PHY_TYPE_USB3_HOST0>;
-+ phy-speed = <PHY_SPEED_5G>;
-+ };
-+
-+ phy1 {
-+ phy-type = <PHY_TYPE_PEX0>;
-+ phy-speed = <PHY_SPEED_2_5G>;
-+ };
-+
-+ phy2 {
-+ phy-type = <PHY_TYPE_SATA0>;
-+ phy-speed = <PHY_SPEED_5G>;
-+ };
-+};
-+
-+ð0 {
-+ status = "okay";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&rgmii_pins>, <&smi_pins>;
-+ phy-mode = "rgmii";
-+ phy_addr = <0x1>;
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
-+ };
-+};
-+
-+&i2c0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins>;
-+ status = "okay";
-+};
-+
-+/* CON3 */
-+&sata {
-+ status = "okay";
-+};
-+
-+&sdhci0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdio_pins>;
-+ bus-width = <4>;
-+ cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>;
-+ vqmmc-supply = <&vcc_sd_reg0>;
-+ status = "okay";
-+};
-+
-+&spi0 {
-+ status = "okay";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi_quad_pins>;
-+
-+ spi-flash@0 {
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ compatible = "st,m25p128", "jedec,spi-nor";
-+ reg = <0>; /* Chip select 0 */
-+ spi-max-frequency = <50000000>;
-+ m25p,fast-read;
-+ };
-+};
-+
-+/* Exported on the micro USB connector CON32 through an FTDI */
-+&uart0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart1_pins>;
-+ status = "okay";
-+};
-+
-+/* CON29 */
-+&usb2 {
-+ status = "okay";
-+};
-+
-+/* CON31 */
-+&usb3 {
-+ status = "okay";
-+};
-+
-+&pcie0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pcie_pins>;
-+ reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
-+ status = "okay";
-+};
+++ /dev/null
-From 408bba2fb84ad0b02c3f9529065126b40899e256 Mon Sep 17 00:00:00 2001
-From: Andre Heider <a.heider@gmail.com>
-Date: Fri, 4 Sep 2020 15:44:41 +0200
-Subject: [PATCH] arm64: dts: a3720: add support for espressobin with
- populated emmc
-
-Import armada-3720-espressobin-emmc.dts from Linux, but use sdhc1 for
-emmc, since our dtsi is still based on downstream and sdhc0 is used for
-the sd card.
-
-Signed-off-by: Andre Heider <a.heider@gmail.com>
----
- arch/arm/dts/Makefile | 1 +
- arch/arm/dts/armada-3720-espressobin-emmc.dts | 44 +++++++++++++++++++
- doc/README.marvell | 7 ++-
- 3 files changed, 50 insertions(+), 2 deletions(-)
- create mode 100644 arch/arm/dts/armada-3720-espressobin-emmc.dts
-
---- a/arch/arm/dts/Makefile
-+++ b/arch/arm/dts/Makefile
-@@ -202,6 +202,7 @@ dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harm
- dtb-$(CONFIG_ARCH_MVEBU) += \
- armada-3720-db.dtb \
- armada-3720-espressobin.dtb \
-+ armada-3720-espressobin-emmc.dtb \
- armada-3720-turris-mox.dtb \
- armada-3720-uDPU.dtb \
- armada-375-db.dtb \
---- /dev/null
-+++ b/arch/arm/dts/armada-3720-espressobin-emmc.dts
-@@ -0,0 +1,44 @@
-+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-+/*
-+ * Device Tree file for Globalscale Marvell ESPRESSOBin Board with eMMC
-+ * Copyright (C) 2018 Marvell
-+ *
-+ * Romain Perier <romain.perier@free-electrons.com>
-+ * Konstantin Porotchkin <kostap@marvell.com>
-+ *
-+ */
-+/*
-+ * Schematic available at http://espressobin.net/wp-content/uploads/2017/08/ESPRESSObin_V5_Schematics.pdf
-+ */
-+
-+/dts-v1/;
-+
-+#include "armada-3720-espressobin.dtsi"
-+
-+/ {
-+ model = "Globalscale Marvell ESPRESSOBin Board (eMMC)";
-+ compatible = "globalscale,espressobin-emmc", "globalscale,espressobin",
-+ "marvell,armada3720", "marvell,armada3710";
-+};
-+
-+/* U11 */
-+&sdhci1 {
-+ non-removable;
-+ bus-width = <8>;
-+ mmc-ddr-1_8v;
-+ mmc-hs400-1_8v;
-+ marvell,xenon-emmc;
-+ marvell,xenon-tun-count = <9>;
-+ marvell,pad-type = "fixed-1-8v";
-+
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&mmc_pins>;
-+ status = "okay";
-+
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mmccard: mmccard@0 {
-+ compatible = "mmc-card";
-+ reg = <0>;
-+ };
-+};
---- a/doc/README.marvell
-+++ b/doc/README.marvell
-@@ -43,8 +43,11 @@ Build Procedure
- In order to prevent this, the required device-tree MUST be set during compilation.
- All device-tree files are located in ./arch/arm/dts/ folder.
-
-- For other DB boards (MacchiatoBin, EspressoBin and 3700 DB board) compile u-boot with
-- just default device-tree from defconfig using:
-+ For the EspressoBin board with populated eMMC device use
-+ # make DEVICE_TREE=armada-3720-espressobin-emmc
-+
-+ For other DB boards (MacchiatoBin, EspressoBin without soldered eMMC and 3700 DB board)
-+ compile u-boot with just default device-tree from defconfig using:
-
- # make
-
projects / openwrt / staging / jow.git / commitdiff