+++ /dev/null
-#ifndef NET2280_H
-#define NET2280_H
-/*
- * NetChip 2280 high/full speed USB device controller.
- * Unlike many such controllers, this one talks PCI.
- */
-
-/*
- * Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com)
- * Copyright (C) 2003 David Brownell
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see <http://www.gnu.org/licenses/>.
- */
-
-/*-------------------------------------------------------------------------*/
-
-/* NET2280 MEMORY MAPPED REGISTERS
- *
- * The register layout came from the chip documentation, and the bit
- * number definitions were extracted from chip specification.
- *
- * Use the shift operator ('<<') to build bit masks, with readl/writel
- * to access the registers through PCI.
- */
-
-/* main registers, BAR0 + 0x0000 */
-struct net2280_regs {
- /* offset 0x0000 */
- __le32 devinit;
-#define LOCAL_CLOCK_FREQUENCY 8
-#define FORCE_PCI_RESET 7
-#define PCI_ID 6
-#define PCI_ENABLE 5
-#define FIFO_SOFT_RESET 4
-#define CFG_SOFT_RESET 3
-#define PCI_SOFT_RESET 2
-#define USB_SOFT_RESET 1
-#define M8051_RESET 0
- __le32 eectl;
-#define EEPROM_ADDRESS_WIDTH 23
-#define EEPROM_CHIP_SELECT_ACTIVE 22
-#define EEPROM_PRESENT 21
-#define EEPROM_VALID 20
-#define EEPROM_BUSY 19
-#define EEPROM_CHIP_SELECT_ENABLE 18
-#define EEPROM_BYTE_READ_START 17
-#define EEPROM_BYTE_WRITE_START 16
-#define EEPROM_READ_DATA 8
-#define EEPROM_WRITE_DATA 0
- __le32 eeclkfreq;
- u32 _unused0;
- /* offset 0x0010 */
-
- __le32 pciirqenb0; /* interrupt PCI master ... */
-#define SETUP_PACKET_INTERRUPT_ENABLE 7
-#define ENDPOINT_F_INTERRUPT_ENABLE 6
-#define ENDPOINT_E_INTERRUPT_ENABLE 5
-#define ENDPOINT_D_INTERRUPT_ENABLE 4
-#define ENDPOINT_C_INTERRUPT_ENABLE 3
-#define ENDPOINT_B_INTERRUPT_ENABLE 2
-#define ENDPOINT_A_INTERRUPT_ENABLE 1
-#define ENDPOINT_0_INTERRUPT_ENABLE 0
- __le32 pciirqenb1;
-#define PCI_INTERRUPT_ENABLE 31
-#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
-#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
-#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
-#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
-#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
-#define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18
-#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
-#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
-#define GPIO_INTERRUPT_ENABLE 13
-#define DMA_D_INTERRUPT_ENABLE 12
-#define DMA_C_INTERRUPT_ENABLE 11
-#define DMA_B_INTERRUPT_ENABLE 10
-#define DMA_A_INTERRUPT_ENABLE 9
-#define EEPROM_DONE_INTERRUPT_ENABLE 8
-#define VBUS_INTERRUPT_ENABLE 7
-#define CONTROL_STATUS_INTERRUPT_ENABLE 6
-#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
-#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
-#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
-#define RESUME_INTERRUPT_ENABLE 1
-#define SOF_INTERRUPT_ENABLE 0
- __le32 cpu_irqenb0; /* ... or onboard 8051 */
-#define SETUP_PACKET_INTERRUPT_ENABLE 7
-#define ENDPOINT_F_INTERRUPT_ENABLE 6
-#define ENDPOINT_E_INTERRUPT_ENABLE 5
-#define ENDPOINT_D_INTERRUPT_ENABLE 4
-#define ENDPOINT_C_INTERRUPT_ENABLE 3
-#define ENDPOINT_B_INTERRUPT_ENABLE 2
-#define ENDPOINT_A_INTERRUPT_ENABLE 1
-#define ENDPOINT_0_INTERRUPT_ENABLE 0
- __le32 cpu_irqenb1;
-#define CPU_INTERRUPT_ENABLE 31
-#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
-#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
-#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
-#define PCI_INTA_INTERRUPT_ENABLE 24
-#define PCI_PME_INTERRUPT_ENABLE 23
-#define PCI_SERR_INTERRUPT_ENABLE 22
-#define PCI_PERR_INTERRUPT_ENABLE 21
-#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
-#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
-#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
-#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
-#define GPIO_INTERRUPT_ENABLE 13
-#define DMA_D_INTERRUPT_ENABLE 12
-#define DMA_C_INTERRUPT_ENABLE 11
-#define DMA_B_INTERRUPT_ENABLE 10
-#define DMA_A_INTERRUPT_ENABLE 9
-#define EEPROM_DONE_INTERRUPT_ENABLE 8
-#define VBUS_INTERRUPT_ENABLE 7
-#define CONTROL_STATUS_INTERRUPT_ENABLE 6
-#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
-#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
-#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
-#define RESUME_INTERRUPT_ENABLE 1
-#define SOF_INTERRUPT_ENABLE 0
-
- /* offset 0x0020 */
- u32 _unused1;
- __le32 usbirqenb1;
-#define USB_INTERRUPT_ENABLE 31
-#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
-#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
-#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
-#define PCI_INTA_INTERRUPT_ENABLE 24
-#define PCI_PME_INTERRUPT_ENABLE 23
-#define PCI_SERR_INTERRUPT_ENABLE 22
-#define PCI_PERR_INTERRUPT_ENABLE 21
-#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
-#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
-#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
-#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
-#define GPIO_INTERRUPT_ENABLE 13
-#define DMA_D_INTERRUPT_ENABLE 12
-#define DMA_C_INTERRUPT_ENABLE 11
-#define DMA_B_INTERRUPT_ENABLE 10
-#define DMA_A_INTERRUPT_ENABLE 9
-#define EEPROM_DONE_INTERRUPT_ENABLE 8
-#define VBUS_INTERRUPT_ENABLE 7
-#define CONTROL_STATUS_INTERRUPT_ENABLE 6
-#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
-#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
-#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
-#define RESUME_INTERRUPT_ENABLE 1
-#define SOF_INTERRUPT_ENABLE 0
- __le32 irqstat0;
-#define INTA_ASSERTED 12
-#define SETUP_PACKET_INTERRUPT 7
-#define ENDPOINT_F_INTERRUPT 6
-#define ENDPOINT_E_INTERRUPT 5
-#define ENDPOINT_D_INTERRUPT 4
-#define ENDPOINT_C_INTERRUPT 3
-#define ENDPOINT_B_INTERRUPT 2
-#define ENDPOINT_A_INTERRUPT 1
-#define ENDPOINT_0_INTERRUPT 0
- __le32 irqstat1;
-#define POWER_STATE_CHANGE_INTERRUPT 27
-#define PCI_ARBITER_TIMEOUT_INTERRUPT 26
-#define PCI_PARITY_ERROR_INTERRUPT 25
-#define PCI_INTA_INTERRUPT 24
-#define PCI_PME_INTERRUPT 23
-#define PCI_SERR_INTERRUPT 22
-#define PCI_PERR_INTERRUPT 21
-#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20
-#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19
-#define PCI_RETRY_ABORT_INTERRUPT 17
-#define PCI_MASTER_CYCLE_DONE_INTERRUPT 16
-#define GPIO_INTERRUPT 13
-#define DMA_D_INTERRUPT 12
-#define DMA_C_INTERRUPT 11
-#define DMA_B_INTERRUPT 10
-#define DMA_A_INTERRUPT 9
-#define EEPROM_DONE_INTERRUPT 8
-#define VBUS_INTERRUPT 7
-#define CONTROL_STATUS_INTERRUPT 6
-#define ROOT_PORT_RESET_INTERRUPT 4
-#define SUSPEND_REQUEST_INTERRUPT 3
-#define SUSPEND_REQUEST_CHANGE_INTERRUPT 2
-#define RESUME_INTERRUPT 1
-#define SOF_INTERRUPT 0
- /* offset 0x0030 */
- __le32 idxaddr;
- __le32 idxdata;
- __le32 fifoctl;
-#define PCI_BASE2_RANGE 16
-#define IGNORE_FIFO_AVAILABILITY 3
-#define PCI_BASE2_SELECT 2
-#define FIFO_CONFIGURATION_SELECT 0
- u32 _unused2;
- /* offset 0x0040 */
- __le32 memaddr;
-#define START 28
-#define DIRECTION 27
-#define FIFO_DIAGNOSTIC_SELECT 24
-#define MEMORY_ADDRESS 0
- __le32 memdata0;
- __le32 memdata1;
- u32 _unused3;
- /* offset 0x0050 */
- __le32 gpioctl;
-#define GPIO3_LED_SELECT 12
-#define GPIO3_INTERRUPT_ENABLE 11
-#define GPIO2_INTERRUPT_ENABLE 10
-#define GPIO1_INTERRUPT_ENABLE 9
-#define GPIO0_INTERRUPT_ENABLE 8
-#define GPIO3_OUTPUT_ENABLE 7
-#define GPIO2_OUTPUT_ENABLE 6
-#define GPIO1_OUTPUT_ENABLE 5
-#define GPIO0_OUTPUT_ENABLE 4
-#define GPIO3_DATA 3
-#define GPIO2_DATA 2
-#define GPIO1_DATA 1
-#define GPIO0_DATA 0
- __le32 gpiostat;
-#define GPIO3_INTERRUPT 3
-#define GPIO2_INTERRUPT 2
-#define GPIO1_INTERRUPT 1
-#define GPIO0_INTERRUPT 0
-} __packed;
-
-/* usb control, BAR0 + 0x0080 */
-struct net2280_usb_regs {
- /* offset 0x0080 */
- __le32 stdrsp;
-#define STALL_UNSUPPORTED_REQUESTS 31
-#define SET_TEST_MODE 16
-#define GET_OTHER_SPEED_CONFIGURATION 15
-#define GET_DEVICE_QUALIFIER 14
-#define SET_ADDRESS 13
-#define ENDPOINT_SET_CLEAR_HALT 12
-#define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11
-#define GET_STRING_DESCRIPTOR_2 10
-#define GET_STRING_DESCRIPTOR_1 9
-#define GET_STRING_DESCRIPTOR_0 8
-#define GET_SET_INTERFACE 6
-#define GET_SET_CONFIGURATION 5
-#define GET_CONFIGURATION_DESCRIPTOR 4
-#define GET_DEVICE_DESCRIPTOR 3
-#define GET_ENDPOINT_STATUS 2
-#define GET_INTERFACE_STATUS 1
-#define GET_DEVICE_STATUS 0
- __le32 prodvendid;
-#define PRODUCT_ID 16
-#define VENDOR_ID 0
- __le32 relnum;
- __le32 usbctl;
-#define SERIAL_NUMBER_INDEX 16
-#define PRODUCT_ID_STRING_ENABLE 13
-#define VENDOR_ID_STRING_ENABLE 12
-#define USB_ROOT_PORT_WAKEUP_ENABLE 11
-#define VBUS_PIN 10
-#define TIMED_DISCONNECT 9
-#define SUSPEND_IMMEDIATELY 7
-#define SELF_POWERED_USB_DEVICE 6
-#define REMOTE_WAKEUP_SUPPORT 5
-#define PME_POLARITY 4
-#define USB_DETECT_ENABLE 3
-#define PME_WAKEUP_ENABLE 2
-#define DEVICE_REMOTE_WAKEUP_ENABLE 1
-#define SELF_POWERED_STATUS 0
- /* offset 0x0090 */
- __le32 usbstat;
-#define HIGH_SPEED 7
-#define FULL_SPEED 6
-#define GENERATE_RESUME 5
-#define GENERATE_DEVICE_REMOTE_WAKEUP 4
- __le32 xcvrdiag;
-#define FORCE_HIGH_SPEED_MODE 31
-#define FORCE_FULL_SPEED_MODE 30
-#define USB_TEST_MODE 24
-#define LINE_STATE 16
-#define TRANSCEIVER_OPERATION_MODE 2
-#define TRANSCEIVER_SELECT 1
-#define TERMINATION_SELECT 0
- __le32 setup0123;
- __le32 setup4567;
- /* offset 0x0090 */
- u32 _unused0;
- __le32 ouraddr;
-#define FORCE_IMMEDIATE 7
-#define OUR_USB_ADDRESS 0
- __le32 ourconfig;
-} __packed;
-
-/* pci control, BAR0 + 0x0100 */
-struct net2280_pci_regs {
- /* offset 0x0100 */
- __le32 pcimstctl;
-#define PCI_ARBITER_PARK_SELECT 13
-#define PCI_MULTI LEVEL_ARBITER 12
-#define PCI_RETRY_ABORT_ENABLE 11
-#define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10
-#define DMA_READ_MULTIPLE_ENABLE 9
-#define DMA_READ_LINE_ENABLE 8
-#define PCI_MASTER_COMMAND_SELECT 6
-#define MEM_READ_OR_WRITE 0
-#define IO_READ_OR_WRITE 1
-#define CFG_READ_OR_WRITE 2
-#define PCI_MASTER_START 5
-#define PCI_MASTER_READ_WRITE 4
-#define PCI_MASTER_WRITE 0
-#define PCI_MASTER_READ 1
-#define PCI_MASTER_BYTE_WRITE_ENABLES 0
- __le32 pcimstaddr;
- __le32 pcimstdata;
- __le32 pcimststat;
-#define PCI_ARBITER_CLEAR 2
-#define PCI_EXTERNAL_ARBITER 1
-#define PCI_HOST_MODE 0
-} __packed;
-
-/* dma control, BAR0 + 0x0180 ... array of four structs like this,
- * for channels 0..3. see also struct net2280_dma: descriptor
- * that can be loaded into some of these registers.
- */
-struct net2280_dma_regs { /* [11.7] */
- /* offset 0x0180, 0x01a0, 0x01c0, 0x01e0, */
- __le32 dmactl;
-#define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25
-#define DMA_CLEAR_COUNT_ENABLE 21
-#define DESCRIPTOR_POLLING_RATE 19
-#define POLL_CONTINUOUS 0
-#define POLL_1_USEC 1
-#define POLL_100_USEC 2
-#define POLL_1_MSEC 3
-#define DMA_VALID_BIT_POLLING_ENABLE 18
-#define DMA_VALID_BIT_ENABLE 17
-#define DMA_SCATTER_GATHER_ENABLE 16
-#define DMA_OUT_AUTO_START_ENABLE 4
-#define DMA_PREEMPT_ENABLE 3
-#define DMA_FIFO_VALIDATE 2
-#define DMA_ENABLE 1
-#define DMA_ADDRESS_HOLD 0
- __le32 dmastat;
-#define DMA_SCATTER_GATHER_DONE_INTERRUPT 25
-#define DMA_TRANSACTION_DONE_INTERRUPT 24
-#define DMA_ABORT 1
-#define DMA_START 0
- u32 _unused0[2];
- /* offset 0x0190, 0x01b0, 0x01d0, 0x01f0, */
- __le32 dmacount;
-#define VALID_BIT 31
-#define DMA_DIRECTION 30
-#define DMA_DONE_INTERRUPT_ENABLE 29
-#define END_OF_CHAIN 28
-#define DMA_BYTE_COUNT_MASK ((1<<24)-1)
-#define DMA_BYTE_COUNT 0
- __le32 dmaaddr;
- __le32 dmadesc;
- u32 _unused1;
-} __packed;
-
-/* dedicated endpoint registers, BAR0 + 0x0200 */
-
-struct net2280_dep_regs { /* [11.8] */
- /* offset 0x0200, 0x0210, 0x220, 0x230, 0x240 */
- __le32 dep_cfg;
- /* offset 0x0204, 0x0214, 0x224, 0x234, 0x244 */
- __le32 dep_rsp;
- u32 _unused[2];
-} __packed;
-
-/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs
- * like this, for ep0 then the configurable endpoints A..F
- * ep0 reserved for control; E and F have only 64 bytes of fifo
- */
-struct net2280_ep_regs { /* [11.9] */
- /* offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0 */
- __le32 ep_cfg;
-#define ENDPOINT_BYTE_COUNT 16
-#define ENDPOINT_ENABLE 10
-#define ENDPOINT_TYPE 8
-#define ENDPOINT_DIRECTION 7
-#define ENDPOINT_NUMBER 0
- __le32 ep_rsp;
-#define SET_NAK_OUT_PACKETS 15
-#define SET_EP_HIDE_STATUS_PHASE 14
-#define SET_EP_FORCE_CRC_ERROR 13
-#define SET_INTERRUPT_MODE 12
-#define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11
-#define SET_NAK_OUT_PACKETS_MODE 10
-#define SET_ENDPOINT_TOGGLE 9
-#define SET_ENDPOINT_HALT 8
-#define CLEAR_NAK_OUT_PACKETS 7
-#define CLEAR_EP_HIDE_STATUS_PHASE 6
-#define CLEAR_EP_FORCE_CRC_ERROR 5
-#define CLEAR_INTERRUPT_MODE 4
-#define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3
-#define CLEAR_NAK_OUT_PACKETS_MODE 2
-#define CLEAR_ENDPOINT_TOGGLE 1
-#define CLEAR_ENDPOINT_HALT 0
- __le32 ep_irqenb;
-#define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6
-#define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5
-#define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3
-#define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2
-#define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1
-#define DATA_IN_TOKEN_INTERRUPT_ENABLE 0
- __le32 ep_stat;
-#define FIFO_VALID_COUNT 24
-#define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22
-#define TIMEOUT 21
-#define USB_STALL_SENT 20
-#define USB_IN_NAK_SENT 19
-#define USB_IN_ACK_RCVD 18
-#define USB_OUT_PING_NAK_SENT 17
-#define USB_OUT_ACK_SENT 16
-#define FIFO_OVERFLOW 13
-#define FIFO_UNDERFLOW 12
-#define FIFO_FULL 11
-#define FIFO_EMPTY 10
-#define FIFO_FLUSH 9
-#define SHORT_PACKET_OUT_DONE_INTERRUPT 6
-#define SHORT_PACKET_TRANSFERRED_INTERRUPT 5
-#define NAK_OUT_PACKETS 4
-#define DATA_PACKET_RECEIVED_INTERRUPT 3
-#define DATA_PACKET_TRANSMITTED_INTERRUPT 2
-#define DATA_OUT_PING_TOKEN_INTERRUPT 1
-#define DATA_IN_TOKEN_INTERRUPT 0
- /* offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0 */
- __le32 ep_avail;
- __le32 ep_data;
- u32 _unused0[2];
-} __packed;
-
-struct net2280_reg_write {
- __le16 port;
- __le32 addr;
- __le32 val;
-} __packed;
-
-struct net2280_reg_read {
- __le16 port;
- __le32 addr;
-} __packed;
-#endif /* NET2280_H */
projects / openwrt / staging / blogic.git / commitdiff