--- /dev/null
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/
+ /*
+ * Copyright 2011-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+ /*
+ * T2080/T2081 QDS board configuration file
+ */
+
+ #ifndef __T208xQDS_H
+ #define __T208xQDS_H
+
+ #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
+ #define CONFIG_MMC
+ #define CONFIG_SPI_FLASH
+ #define CONFIG_USB_EHCI
+ #if defined(CONFIG_PPC_T2080)
+ #define CONFIG_T2080QDS
+ #define CONFIG_FSL_SATA_V2
+ #define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */
+ #define CONFIG_SRIO1 /* SRIO port 1 */
+ #define CONFIG_SRIO2 /* SRIO port 2 */
+ #elif defined(CONFIG_PPC_T2081)
+ #define CONFIG_T2081QDS
+ #endif
+
+ /* High Level Configuration Options */
+ #define CONFIG_PHYS_64BIT
+ #define CONFIG_BOOKE
+ #define CONFIG_E500 /* BOOKE e500 family */
+ #define CONFIG_E500MC /* BOOKE e500mc family */
+ #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+ #define CONFIG_MP /* support multiple processors */
+ #define CONFIG_ENABLE_36BIT_PHYS
+
+ #ifdef CONFIG_PHYS_64BIT
+ #define CONFIG_ADDR_MAP 1
+ #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+ #endif
+
+ #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+ #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+ #define CONFIG_FSL_IFC /* Enable IFC Support */
+ #define CONFIG_FSL_LAW /* Use common FSL init code */
+ #define CONFIG_ENV_OVERWRITE
+
+ #ifdef CONFIG_RAMBOOT_PBL
+ #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+ #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+ #define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t208xqds/t208x_pbi.cfg
+ #if defined(CONFIG_PPC_T2080)
+ #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xqds/t2080_rcw.cfg
+ #elif defined(CONFIG_PPC_T2081)
+ #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xqds/t2081_rcw.cfg
+ #endif
+ #endif
+
+ #define CONFIG_SRIO_PCIE_BOOT_MASTER
+ #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+ /* Set 1M boot space */
+ #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+ #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+ #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+ #define CONFIG_SYS_NO_FLASH
+ #endif
+
+ #ifndef CONFIG_SYS_TEXT_BASE
+ #define CONFIG_SYS_TEXT_BASE 0xeff40000
+ #endif
+
+ #ifndef CONFIG_RESET_VECTOR_ADDRESS
+ #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+ #endif
+
+ /*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+ #define CONFIG_SYS_CACHE_STASHING
+ #define CONFIG_BTB /* toggle branch predition */
+ #define CONFIG_DDR_ECC
+ #ifdef CONFIG_DDR_ECC
+ #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+ #define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+ #endif
+
+ #ifdef CONFIG_SYS_NO_FLASH
+ #if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
+ #define CONFIG_ENV_IS_NOWHERE
+ #endif
+ #else
+ #define CONFIG_FLASH_CFI_DRIVER
+ #define CONFIG_SYS_FLASH_CFI
+ #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+ #endif
+
+ #if defined(CONFIG_SPIFLASH)
+ #define CONFIG_SYS_EXTRA_ENV_RELOC
+ #define CONFIG_ENV_IS_IN_SPI_FLASH
+ #define CONFIG_ENV_SPI_BUS 0
+ #define CONFIG_ENV_SPI_CS 0
+ #define CONFIG_ENV_SPI_MAX_HZ 10000000
+ #define CONFIG_ENV_SPI_MODE 0
+ #define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+ #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+ #define CONFIG_ENV_SECT_SIZE 0x10000
+ #elif defined(CONFIG_SDCARD)
+ #define CONFIG_SYS_EXTRA_ENV_RELOC
+ #define CONFIG_ENV_IS_IN_MMC
+ #define CONFIG_SYS_MMC_ENV_DEV 0
+ #define CONFIG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_OFFSET (512 * 1658)
+ #elif defined(CONFIG_NAND)
+ #define CONFIG_SYS_EXTRA_ENV_RELOC
+ #define CONFIG_ENV_IS_IN_NAND
+ #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+ #define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
+ #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+ #define CONFIG_ENV_IS_IN_REMOTE
+ #define CONFIG_ENV_ADDR 0xffe20000
+ #define CONFIG_ENV_SIZE 0x2000
+ #elif defined(CONFIG_ENV_IS_NOWHERE)
+ #define CONFIG_ENV_SIZE 0x2000
+ #else
+ #define CONFIG_ENV_IS_IN_FLASH
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+ #define CONFIG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+ #endif
+
+ #ifndef __ASSEMBLY__
+ unsigned long get_board_sys_clk(void);
+ unsigned long get_board_ddr_clk(void);
+ #endif
+
+ #define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
+ #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
+
+ /*
+ * Config the L3 Cache as L3 SRAM
+ */
+ #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+
+ #define CONFIG_SYS_DCSRBAR 0xf0000000
+ #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+
+ /* EEPROM */
+ #define CONFIG_ID_EEPROM
+ #define CONFIG_SYS_I2C_EEPROM_NXID
+ #define CONFIG_SYS_EEPROM_BUS_NUM 0
+ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+ /*
+ * DDR Setup
+ */
+ #define CONFIG_VERY_BIG_RAM
+ #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+ #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+ #define CONFIG_DIMM_SLOTS_PER_CTLR 1
+ #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+ #define CONFIG_DDR_SPD
+ #define CONFIG_SYS_FSL_DDR3
+ #undef CONFIG_FSL_DDR_INTERACTIVE
+ #define CONFIG_SYS_SPD_BUS_NUM 0
+ #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
+ #define SPD_EEPROM_ADDRESS1 0x51
+ #define SPD_EEPROM_ADDRESS2 0x52
+ #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
+ #define CTRL_INTLV_PREFERED cacheline
+
+ /*
+ * IFC Definitions
+ */
+ #define CONFIG_SYS_FLASH_BASE 0xe0000000
+ #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+ #define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
+ #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+ #define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
+ #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+ #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+ /* NOR Flash Timing Params */
+ #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
+
+ #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+ #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1A) |\
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+ #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x0E) | \
+ FTIM2_NOR_TWP(0x1c))
+ #define CONFIG_SYS_NOR_FTIM3 0x0
+
+ #define CONFIG_SYS_FLASH_QUIET_TEST
+ #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+ #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+ #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+ #define CONFIG_SYS_FLASH_EMPTY_INFO
+ #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+
+ #define CONFIG_FSL_QIXIS /* use common QIXIS code */
+ #define QIXIS_BASE 0xffdf0000
+ #define QIXIS_LBMAP_SWITCH 6
+ #define QIXIS_LBMAP_MASK 0x0f
+ #define QIXIS_LBMAP_SHIFT 0
+ #define QIXIS_LBMAP_DFLTBANK 0x00
+ #define QIXIS_LBMAP_ALTBANK 0x04
+ #define QIXIS_RST_CTL_RESET 0x83
+ #define QIXIS_RST_FORCE_MEM 0x1
+ #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+ #define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+ #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+ #define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE)
+
+ #define CONFIG_SYS_CSPR3_EXT (0xf)
+ #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+ #define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024)
+ #define CONFIG_SYS_CSOR3 0x0
+ /* QIXIS Timing parameters for IFC CS3 */
+ #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+ #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
+ FTIM1_GPCM_TRAD(0x3f))
+ #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x0) | \
+ FTIM2_GPCM_TWP(0x1f))
+ #define CONFIG_SYS_CS3_FTIM3 0x0
+
+ /* NAND Flash on IFC */
+ #define CONFIG_NAND_FSL_IFC
+ #define CONFIG_SYS_NAND_BASE 0xff800000
+ #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+ #define CONFIG_SYS_NAND_CSPR_EXT (0xf)
+ #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+ #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+ #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */\
+ | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+ #define CONFIG_SYS_NAND_ONFI_DETECTION
+
+ /* ONFI NAND Flash mode0 Timing Params */
+ #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+ #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+ #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+ #define CONFIG_SYS_NAND_FTIM3 0x0
+
+ #define CONFIG_SYS_NAND_DDR_LAW 11
+ #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+ #define CONFIG_SYS_MAX_NAND_DEVICE 1
+ #define CONFIG_MTD_NAND_VERIFY_WRITE
+ #define CONFIG_CMD_NAND
+ #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+ #if defined(CONFIG_NAND)
+ #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+ #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+ #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+ #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+ #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+ #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+ #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+ #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+ #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
+ #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR
+ #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
+ #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
+ #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
+ #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
+ #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
+ #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
+ #else
+ #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+ #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
+ #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+ #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+ #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+ #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+ #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+ #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+ #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
+ #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
+ #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
+ #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
+ #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
+ #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
+ #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
+ #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+ #endif
+ #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
+ #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
+ #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+ #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+ #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+ #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+ #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+ #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+
+ #if defined(CONFIG_RAMBOOT_PBL)
+ #define CONFIG_SYS_RAMBOOT
+ #endif
+
+ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+ #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+ #define CONFIG_MISC_INIT_R
+ #define CONFIG_HWCONFIG
+
+ /* define to use L1 as initial stack */
+ #define CONFIG_L1_INIT_RAM
+ #define CONFIG_SYS_INIT_RAM_LOCK
+ #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
+ #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+ #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000
+ /* The assembler doesn't like typecast */
+ #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+ #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+ #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+ #define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+ #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
+
+ /*
+ * Serial Port
+ */
+ #define CONFIG_CONS_INDEX 1
+ #define CONFIG_SYS_NS16550
+ #define CONFIG_SYS_NS16550_SERIAL
+ #define CONFIG_SYS_NS16550_REG_SIZE 1
+ #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+ #define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+ #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+ #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+ #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+ #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+
+ /* Use the HUSH parser */
+ #define CONFIG_SYS_HUSH_PARSER
+ #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+ /* pass open firmware flat tree */
+ #define CONFIG_OF_LIBFDT
+ #define CONFIG_OF_BOARD_SETUP
+ #define CONFIG_OF_STDOUT_VIA_ALIAS
+
+ /* new uImage format support */
+ #define CONFIG_FIT
+ #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+ /*
+ * I2C
+ */
+ #define CONFIG_SYS_I2C
+ #define CONFIG_SYS_I2C_FSL
+ #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+ #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+ #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
+ #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
+ #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+ #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
+ #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
+ #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
+ #define CONFIG_SYS_FSL_I2C_SPEED 100000
+ #define CONFIG_SYS_FSL_I2C2_SPEED 100000
+ #define CONFIG_SYS_FSL_I2C3_SPEED 100000
+ #define CONFIG_SYS_FSL_I2C4_SPEED 100000
+ #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
+ #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */
+ #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */
+ #define I2C_MUX_CH_DEFAULT 0x8
+
+
+ /*
+ * RapidIO
+ */
+ #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
+ #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
+ #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
+ #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
+ #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
+ #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
+ /*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+ #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
+ #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
+ #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
+ #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+ /*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+ #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+ #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+ #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
+
+ /* slave core release by master*/
+ #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+ #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+ /*
+ * SRIO_PCIE_BOOT - SLAVE
+ */
+ #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+ #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+ #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+ #endif
+
+ /*
+ * eSPI - Enhanced SPI
+ */
+ #ifdef CONFIG_SPI_FLASH
+ #define CONFIG_FSL_ESPI
+ #define CONFIG_SPI_FLASH_SST
+ #define CONFIG_SPI_FLASH_STMICRO
+ #if defined(CONFIG_T2080QDS)
+ #define CONFIG_SPI_FLASH_SPANSION
+ #elif defined(CONFIG_T2081QDS)
+ #define CONFIG_SPI_FLASH_EON
+ #endif
+
+ #define CONFIG_CMD_SF
+ #define CONFIG_SF_DEFAULT_SPEED 10000000
+ #define CONFIG_SF_DEFAULT_MODE 0
+ #endif
+
+ /*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+ #define CONFIG_PCI /* Enable PCI/PCIE */
+ #define CONFIG_PCIE1 /* PCIE controler 1 */
+ #define CONFIG_PCIE2 /* PCIE controler 2 */
+ #define CONFIG_PCIE3 /* PCIE controler 3 */
+ #define CONFIG_PCIE4 /* PCIE controler 4 */
+ #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+ #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+ /* controller 1, direct to uli, tgtid 3, Base address 20000 */
+ #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+ #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+ #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+ #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+ #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+ #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+ #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+ #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+ /* controller 2, Slot 2, tgtid 2, Base address 201000 */
+ #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+ #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+ #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+ #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+ #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
+ #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+ #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
+ #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+ /* controller 3, Slot 1, tgtid 1, Base address 202000 */
+ #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000
+ #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+ #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull
+ #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
+ #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
+ #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+ #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
+ #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+ /* controller 4, Base address 203000 */
+ #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000
+ #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
+ #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull
+ #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
+ #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
+ #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
+ #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
+
+ #ifdef CONFIG_PCI
+ #define CONFIG_PCI_INDIRECT_BRIDGE
+ #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
+ #define CONFIG_NET_MULTI
+ #define CONFIG_E1000
+ #define CONFIG_PCI_PNP /* do pci plug-and-play */
+ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+ #define CONFIG_DOS_PARTITION
+ #endif
+
+ /* Qman/Bman */
+ #ifndef CONFIG_NOBQFMAN
+ #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+ #define CONFIG_SYS_BMAN_NUM_PORTALS 18
+ #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+ #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+ #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
+ #define CONFIG_SYS_QMAN_NUM_PORTALS 18
+ #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
+ #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
+ #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
+
+ #define CONFIG_SYS_DPAA_FMAN
+ #define CONFIG_SYS_DPAA_PME
+ #define CONFIG_SYS_PMAN
+ #define CONFIG_SYS_DPAA_DCE
+ #define CONFIG_SYS_DPAA_RMAN /* RMan */
+ #define CONFIG_SYS_INTERLAKEN
+
+ /* Default address of microcode for the Linux Fman driver */
+ #if defined(CONFIG_SPIFLASH)
+ /*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+ #define CONFIG_SYS_QE_FW_IN_SPIFLASH
+ #define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000
+ #elif defined(CONFIG_SDCARD)
+ /*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 825KB (1650 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ */
+ #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+ #define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1680)
+ #elif defined(CONFIG_NAND)
+ #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+ #define CONFIG_SYS_QE_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+ #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+ /*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+ #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+ #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000
+ #else
+ #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+ #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF00000
+ #endif
+ #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+ #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+ #endif /* CONFIG_NOBQFMAN */
+
+ #ifdef CONFIG_SYS_DPAA_FMAN
+ #define CONFIG_FMAN_ENET
+ #define CONFIG_PHYLIB_10G
+ #define CONFIG_PHY_VITESSE
+ #define CONFIG_PHY_REALTEK
+ #define CONFIG_PHY_TERANETICS
+ #define RGMII_PHY1_ADDR 0x1
+ #define RGMII_PHY2_ADDR 0x2
+ #define FM1_10GEC1_PHY_ADDR 0x3
+ #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+ #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
+ #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+ #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+ #endif
+
+ #ifdef CONFIG_FMAN_ENET
+ #define CONFIG_MII /* MII PHY management */
+ #define CONFIG_ETHPRIME "FM1@DTSEC3"
+ #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+ #endif
+
+ /*
+ * SATA
+ */
+ #ifdef CONFIG_FSL_SATA_V2
+ #define CONFIG_LIBATA
+ #define CONFIG_FSL_SATA
+ #define CONFIG_SYS_SATA_MAX_DEVICE 2
+ #define CONFIG_SATA1
+ #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
+ #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
+ #define CONFIG_SATA2
+ #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
+ #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
+ #define CONFIG_LBA48
+ #define CONFIG_CMD_SATA
+ #define CONFIG_DOS_PARTITION
+ #define CONFIG_CMD_EXT2
+ #endif
+
+ /*
+ * USB
+ */
+ #ifdef CONFIG_USB_EHCI
+ #define CONFIG_CMD_USB
+ #define CONFIG_USB_STORAGE
+ #define CONFIG_USB_EHCI_FSL
+ #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+ #define CONFIG_CMD_EXT2
+ #define CONFIG_HAS_FSL_DR_USB
+ #endif
+
+ /*
+ * SDHC
+ */
+ #ifdef CONFIG_MMC
+ #define CONFIG_CMD_MMC
+ #define CONFIG_FSL_ESDHC
+ #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+ #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+ #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+ #define CONFIG_GENERIC_MMC
+ #define CONFIG_CMD_EXT2
+ #define CONFIG_CMD_FAT
+ #define CONFIG_DOS_PARTITION
+ #endif
+
+ /*
+ * Environment
+ */
+ #define CONFIG_LOADS_ECHO /* echo on for serial download */
+ #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+ /*
+ * Command line configuration.
+ */
+ #include <config_cmd_default.h>
+
+ #define CONFIG_CMD_DHCP
+ #define CONFIG_CMD_ELF
+ #define CONFIG_CMD_ERRATA
+ #define CONFIG_CMD_GREPENV
+ #define CONFIG_CMD_IRQ
+ #define CONFIG_CMD_I2C
+ #define CONFIG_CMD_MII
+ #define CONFIG_CMD_PING
+ #define CONFIG_CMD_SETEXPR
+ #define CONFIG_CMD_REGINFO
+ #define CONFIG_CMD_BDI
+
+ #ifdef CONFIG_PCI
+ #define CONFIG_CMD_PCI
+ #define CONFIG_CMD_NET
+ #endif
+
+ /*
+ * Miscellaneous configurable options
+ */
+ #define CONFIG_SYS_LONGHELP /* undef to save memory */
+ #define CONFIG_CMDLINE_EDITING /* Command-line editing */
+ #define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+ #ifdef CONFIG_CMD_KGDB
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+ #else
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+ #endif
+ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+
+ /*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+ #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
+ #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+ #ifdef CONFIG_CMD_KGDB
+ #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+ #endif
+
+ /*
+ * Environment Configuration
+ */
+ #define CONFIG_ROOTPATH "/opt/nfsroot"
+ #define CONFIG_BOOTFILE "uImage"
+ #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
+
+ /* default location for tftp and bootm */
+ #define CONFIG_LOADADDR 1000000
+ #define CONFIG_BAUDRATE 115200
+ #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+ #define __USB_PHY_TYPE utmi
+
+ #define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:" \
+ "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
+ "bank_intlv=auto;" \
+ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+ "netdev=eth0\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot && " \
+ "protect off $ubootaddr +$filesize && " \
+ "erase $ubootaddr +$filesize && " \
+ "cp.b $loadaddr $ubootaddr $filesize && " \
+ "protect on $ubootaddr +$filesize && " \
+ "cmp.b $loadaddr $ubootaddr $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=t2080qds/ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=t2080qds/t2080qds.dtb\0" \
+ "bdev=sda3\0" \
+ "c=ffe\0"
+
+ /*
+ * For emulation this causes u-boot to jump to the start of the
+ * proof point app code automatically
+ */
+ #define CONFIG_PROOF_POINTS \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x29000000 - - -;" \
+ "cpu 2 release 0x29000000 - - -;" \
+ "cpu 3 release 0x29000000 - - -;" \
+ "cpu 4 release 0x29000000 - - -;" \
+ "cpu 5 release 0x29000000 - - -;" \
+ "cpu 6 release 0x29000000 - - -;" \
+ "cpu 7 release 0x29000000 - - -;" \
+ "go 0x29000000"
+
+ #define CONFIG_HVBOOT \
+ "setenv bootargs config-addr=0x60000000; " \
+ "bootm 0x01000000 - 0x00f00000"
+
+ #define CONFIG_ALU \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x01000000 - - -;" \
+ "cpu 2 release 0x01000000 - - -;" \
+ "cpu 3 release 0x01000000 - - -;" \
+ "cpu 4 release 0x01000000 - - -;" \
+ "cpu 5 release 0x01000000 - - -;" \
+ "cpu 6 release 0x01000000 - - -;" \
+ "cpu 7 release 0x01000000 - - -;" \
+ "go 0x01000000"
+
+ #define CONFIG_LINUX \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "setenv ramdiskaddr 0x02000000;" \
+ "setenv fdtaddr 0x00c00000;" \
+ "setenv loadaddr 0x1000000;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+ #define CONFIG_HDBOOT \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+ #define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+ #define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+ #define CONFIG_BOOTCOMMAND CONFIG_LINUX
+
+ #ifdef CONFIG_SECURE_BOOT
+ #include <asm/fsl_secure_boot.h>
+ #undef CONFIG_CMD_USB
+ #endif
+
+ #endif /* __T208xQDS_H */
projects / project / bcm63xx / u-boot.git / commitdiff