ucidef_set_led_netdev "eth" "Ethernet" "$board:green:lan" "eth0"
set_wifi_led "$board:blue:wlan"
;;
+kn|\
+nbg-419n2)
+ set_usb_led "$board:green:usb"
+ set_wifi_led "rt2800pci-phy0::radio"
+ ;;
kn_rc|\
kn_rf|\
kng_rc)
na930)
set_usb_led "$board:blue:status"
;;
-nbg-419n2)
- set_usb_led "$board:green:usb"
- set_wifi_led "rt2800pci-phy0::radio"
- ;;
newifi-d1)
set_usb_led "$board:red:status"
;;
--- /dev/null
+/dts-v1/;
+
+#include "rt3050.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "zyxel,keenetic", "ralink,rt3052-soc";
+ model = "ZyXEL Keenetic";
+
+ cfi@1f000000 {
+ compatible = "cfi-flash";
+ reg = <0x1f000000 0x800000>;
+ bank-width = <2>;
+ device-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition@40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition@50000 {
+ label = "firmware";
+ reg = <0x50000 0x3b0000>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ power {
+ label = "kn:green:power";
+ gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+ };
+
+ usb {
+ label = "kn:green:usb";
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "kn:green:wps";
+ gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ rfkill {
+ label = "rfkill";
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_RFKILL>;
+ linux,input-type = <EV_SW>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "uartf";
+ ralink,function = "gpio";
+ };
+ };
+};
+
+ðernet {
+ mtd-mac-address = <&factory 0x28>;
+};
+
+&esw {
+ mediatek,portmap = <0x2f>;
+};
+
+&wmac {
+ ralink,mtd-eeprom = <&factory 0>;
+};
+
+&otg {
+ status = "okay";
+};