ath79: add support for Netgear WNDR4500 v3

This patch introduces support for Netgear WNDR4500v3. Router
is very similar to WNDR4300v2 and is based on the same PCB.

Information gathered from various Internet sources (including
https://patchwork.ozlabs.org/patch/809227/) shows following
differences to WNDR4300v2:

 * two USB 2.0 ports with separate LEDs
 * USB LEDs soldered to secondary pads
 * WPS and RFKILL buttons soldered to secondary pads
 * described as N900 device with 3x3:3 MIMO for 2.4GHz radio
 * power supply requirement is DC 12V 2.5A
 * vendor HW ID suffix differs in one digit
 * bigger chassis

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index 85a0342a605e2a32b310ff75a3128c168c8ceffd..aafced98dbeb5b7bcd14f5376c4a7f85ca8596fe 100644 (file)
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -27,6 +27,7 @@ librerouter,librerouter-v1|\
 netgear,ex6400|\
 netgear,ex7300|\
 netgear,wndr4300-v2|\
+netgear,wndr4500-v3|\
 netgear,wnr1000-v2|\
 netgear,wnr2000-v3|\
 netgear,wnr2200-8m|\

diff --git a/target/linux/ath79/dts/qca9563_netgear_wndr4500-v3.dts b/target/linux/ath79/dts/qca9563_netgear_wndr4500-v3.dts
new file mode 100644 (file)
index 0000000..95e30ea
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_netgear_wndr4500-v3.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "qca9563_netgear_wndr.dtsi"
+
+/ {
+       compatible = "netgear,wndr4500-v3", "qca,qca9563";
+       model = "Netgear WNDR4500 v3";
+};
+
+&leds {
+       usb1_green {
+               label = "netgear:green:usb1";
+               gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+               trigger-sources = <&hub_port0>;
+               linux,default-trigger = "usbport";
+       };
+
+       usb2_green {
+               label = "netgear:green:usb2";
+               gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+               trigger-sources = <&hub_port1>;
+               linux,default-trigger = "usbport";
+       };
+};
+
+&usb_phy1 {
+       status = "okay";
+};
+
+&usb1 {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       status = "okay";
+
+       hub_port1: port@1 {
+               reg = <1>;
+               #trigger-source-cells = <0>;
+       };
+};

diff --git a/target/linux/ath79/image/nand.mk b/target/linux/ath79/image/nand.mk
index d5213523e425ed159c98c2cccba5ebe3d69b2405..f6929cd88e7e38a12a76d5b5cf4ba8cd2b6c417f 100644 (file)
--- a/target/linux/ath79/image/nand.mk
+++ b/target/linux/ath79/image/nand.mk
@@ -165,6 +165,17 @@ define Device/netgear_wndr4300-v2
 endef
 TARGET_DEVICES += netgear_wndr4300-v2
 
+define Device/netgear_wndr4500-v3
+  SOC := qca9563
+  DEVICE_MODEL := WNDR4500
+  DEVICE_VARIANT := v3
+  NETGEAR_KERNEL_MAGIC := 0x27051956
+  NETGEAR_BOARD_ID := WNDR4500series
+  NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012173
+  $(Device/netgear_ath79_nand)
+endef
+TARGET_DEVICES += netgear_wndr4500-v3
+
 define Device/zyxel_nbg6716
   SOC := qca9558
   DEVICE_VENDOR := ZyXEL

diff --git a/target/linux/ath79/nand/base-files/etc/board.d/01_leds b/target/linux/ath79/nand/base-files/etc/board.d/01_leds
index 0376b7cfc662373827e144462b172dda61c869c9..d9989ec5382271b4cc547c897be1681809cc2a12 100755 (executable)
--- a/target/linux/ath79/nand/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/nand/base-files/etc/board.d/01_leds
@@ -14,7 +14,8 @@ glinet,gl-ar300m-nor)
        ;;
 netgear,wndr3700-v4|\
 netgear,wndr4300|\
-netgear,wndr4300-v2)
+netgear,wndr4300-v2|\
+netgear,wndr4500-v3)
        ucidef_set_led_switch "wan-amber" "WAN (amber)" "netgear:amber:wan" "switch0" "0x20"
        ;;
 esac

diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network
index 135a06d44bf4428d80c38b4e536e43583b6b1e41..bd02a4b38364ff1d9155a836cb144919809c7800 100755 (executable)
--- a/target/linux/ath79/nand/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network
@@ -18,7 +18,8 @@ ath79_setup_interfaces()
                ;;
        netgear,wndr3700-v4|\
        netgear,wndr4300|\
-       netgear,wndr4300-v2)
+       netgear,wndr4300-v2|\
+       netgear,wndr4500-v3)
                ucidef_add_switch "switch0" \
                        "0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
                ;;
@@ -39,7 +40,8 @@ ath79_setup_macs()
        case "$board" in
        netgear,wndr3700-v4|\
        netgear,wndr4300|\
-       netgear,wndr4300-v2)
+       netgear,wndr4300-v2|\
+       netgear,wndr4500-v3)
                wan_mac=$(mtd_get_mac_binary caldata 0x6)
                ;;
        zyxel,nbg6716)

diff --git a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 7ee291d1096512e404debbe1e5e58e696bd59d87..d2f8bae1caa0304ab3ef3d3b23d3b9788adfb6ff 100644 (file)
--- a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -11,7 +11,8 @@ case "$FIRMWARE" in
        case $board in
        netgear,wndr3700-v4|\
        netgear,wndr4300|\
-       netgear,wndr4300-v2)
+       netgear,wndr4300-v2|\
+       netgear,wndr4500-v3)
                caldata_extract "caldata" 0x1000 0x440
                ;;
        zyxel,nbg6716)
@@ -27,7 +28,8 @@ case "$FIRMWARE" in
        case $board in
        netgear,wndr3700-v4|\
        netgear,wndr4300|\
-       netgear,wndr4300-v2)
+       netgear,wndr4300-v2|\
+       netgear,wndr4500-v3)
                caldata_extract "caldata" 0x5000 0x440
                ;;
        *)