--- a/nl80211.h
+++ b/nl80211.h
-@@ -11,7 +11,7 @@
- * Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
- * Copyright 2008 Colin McCabe <colin@cozybit.com>
- * Copyright 2015-2017 Intel Deutschland GmbH
-- * Copyright (C) 2018-2020 Intel Corporation
-+ * Copyright (C) 2018-2021 Intel Corporation
- *
- * Permission to use, copy, modify, and/or distribute this software for any
- * purpose with or without fee is hereby granted, provided that the above
-@@ -655,6 +655,9 @@
- * When a security association was established on an 802.1X network using
- * fast transition, this event should be followed by an
- * %NL80211_CMD_PORT_AUTHORIZED event.
-+ * Following a %NL80211_CMD_ROAM event userspace can issue
-+ * %NL80211_CMD_GET_SCAN in order to obtain the scan information for the
-+ * new BSS the card/driver roamed to.
- * @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
- * userspace that a connection was dropped by the AP or due to other
- * reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and
-@@ -757,7 +760,8 @@
- * of any other interfaces, and other interfaces will again take
- * precedence when they are used.
+@@ -301,29 +301,6 @@
+ */
+
+ /**
+- * DOC: FILS shared key crypto offload
+- *
+- * This feature is applicable to drivers running in AP mode.
+- *
+- * FILS shared key crypto offload can be advertised by drivers by setting
+- * @NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD flag. The drivers that support
+- * FILS shared key crypto offload should be able to encrypt and decrypt
+- * association frames for FILS shared key authentication as per IEEE 802.11ai.
+- * With this capability, for FILS key derivation, drivers depend on userspace.
+- *
+- * After FILS key derivation, userspace shares the FILS AAD details with the
+- * driver and the driver stores the same to use in decryption of association
+- * request and in encryption of association response. The below parameters
+- * should be given to the driver in %NL80211_CMD_SET_FILS_AAD.
+- * %NL80211_ATTR_MAC - STA MAC address, used for storing FILS AAD per STA
+- * %NL80211_ATTR_FILS_KEK - Used for encryption or decryption
+- * %NL80211_ATTR_FILS_NONCES - Used for encryption or decryption
+- * (STA Nonce 16 bytes followed by AP Nonce 16 bytes)
+- *
+- * Once the association is done, the driver cleans the FILS AAD data.
+- */
+-
+-/**
+ * enum nl80211_commands - supported nl80211 commands
*
-- * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
-+ * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface
-+ * (no longer supported).
+ * @NL80211_CMD_UNSPEC: unspecified command to catch errors
+@@ -360,10 +337,7 @@
+ * @NL80211_CMD_DEL_INTERFACE: Virtual interface was deleted, has attributes
+ * %NL80211_ATTR_IFINDEX and %NL80211_ATTR_WIPHY. Can also be sent from
+ * userspace to request deletion of a virtual interface, then requires
+- * attribute %NL80211_ATTR_IFINDEX. If multiple BSSID advertisements are
+- * enabled using %NL80211_ATTR_MBSSID_CONFIG, %NL80211_ATTR_MBSSID_ELEMS,
+- * and if this command is used for the transmitting interface, then all
+- * the non-transmitting interfaces are deleted as well.
++ * attribute %NL80211_ATTR_IFINDEX.
*
- * @NL80211_CMD_SET_MULTICAST_TO_UNICAST: Configure if this AP should perform
- * multicast to unicast conversion. When enabled, all multicast packets
-@@ -1177,6 +1181,25 @@
- * includes the contents of the frame. %NL80211_ATTR_ACK flag is included
- * if the recipient acknowledged the frame.
+ * @NL80211_CMD_GET_KEY: Get sequence counter information for a key specified
+ * by %NL80211_ATTR_KEY_IDX and/or %NL80211_ATTR_MAC.
+@@ -1226,12 +1200,6 @@
+ * @NL80211_CMD_COLOR_CHANGE_COMPLETED: Notify userland that the color change
+ * has completed
*
-+ * @NL80211_CMD_SET_SAR_SPECS: SAR power limitation configuration is
-+ * passed using %NL80211_ATTR_SAR_SPEC. %NL80211_ATTR_WIPHY is used to
-+ * specify the wiphy index to be applied to.
-+ *
-+ * @NL80211_CMD_OBSS_COLOR_COLLISION: This notification is sent out whenever
-+ * mac80211/drv detects a bss color collision.
-+ *
-+ * @NL80211_CMD_COLOR_CHANGE_REQUEST: This command is used to indicate that
-+ * userspace wants to change the BSS color.
-+ *
-+ * @NL80211_CMD_COLOR_CHANGE_STARTED: Notify userland, that a color change has
-+ * started
-+ *
-+ * @NL80211_CMD_COLOR_CHANGE_ABORTED: Notify userland, that the color change has
-+ * been aborted
-+ *
-+ * @NL80211_CMD_COLOR_CHANGE_COMPLETED: Notify userland that the color change
-+ * has completed
-+ *
+- * @NL80211_CMD_SET_FILS_AAD: Set FILS AAD data to the driver using -
+- * &NL80211_ATTR_MAC - for STA MAC address
+- * &NL80211_ATTR_FILS_KEK - for KEK
+- * &NL80211_ATTR_FILS_NONCES - for FILS Nonces
+- * (STA Nonce 16 bytes followed by AP Nonce 16 bytes)
+- *
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
-@@ -1407,6 +1430,16 @@ enum nl80211_commands {
+@@ -1472,8 +1440,6 @@ enum nl80211_commands {
+ NL80211_CMD_COLOR_CHANGE_ABORTED,
+ NL80211_CMD_COLOR_CHANGE_COMPLETED,
- NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS,
-
-+ NL80211_CMD_SET_SAR_SPECS,
-+
-+ NL80211_CMD_OBSS_COLOR_COLLISION,
-+
-+ NL80211_CMD_COLOR_CHANGE_REQUEST,
-+
-+ NL80211_CMD_COLOR_CHANGE_STARTED,
-+ NL80211_CMD_COLOR_CHANGE_ABORTED,
-+ NL80211_CMD_COLOR_CHANGE_COMPLETED,
-+
+- NL80211_CMD_SET_FILS_AAD,
+-
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
-@@ -1750,8 +1783,9 @@ enum nl80211_commands {
- * specify just a single bitrate, which is to be used for the beacon.
- * The driver must also specify support for this with the extended
- * features NL80211_EXT_FEATURE_BEACON_RATE_LEGACY,
-- * NL80211_EXT_FEATURE_BEACON_RATE_HT and
-- * NL80211_EXT_FEATURE_BEACON_RATE_VHT.
-+ * NL80211_EXT_FEATURE_BEACON_RATE_HT,
-+ * NL80211_EXT_FEATURE_BEACON_RATE_VHT and
-+ * NL80211_EXT_FEATURE_BEACON_RATE_HE.
- *
- * @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
- * at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME.
-@@ -1955,8 +1989,15 @@ enum nl80211_commands {
- * @NL80211_ATTR_PROBE_RESP: Probe Response template data. Contains the entire
- * probe-response frame. The DA field in the 802.11 header is zero-ed out,
- * to be filled by the FW.
-- * @NL80211_ATTR_DISABLE_HT: Force HT capable interfaces to disable
-- * this feature. Currently, only supported in mac80211 drivers.
-+ * @NL80211_ATTR_DISABLE_HT: Force HT capable interfaces to disable
-+ * this feature during association. This is a flag attribute.
-+ * Currently only supported in mac80211 drivers.
-+ * @NL80211_ATTR_DISABLE_VHT: Force VHT capable interfaces to disable
-+ * this feature during association. This is a flag attribute.
-+ * Currently only supported in mac80211 drivers.
-+ * @NL80211_ATTR_DISABLE_HE: Force HE capable interfaces to disable
-+ * this feature during association. This is a flag attribute.
-+ * Currently only supported in mac80211 drivers.
- * @NL80211_ATTR_HT_CAPABILITY_MASK: Specify which bits of the
- * ATTR_HT_CAPABILITY to which attention should be paid.
- * Currently, only mac80211 NICs support this feature.
-@@ -2077,7 +2118,8 @@ enum nl80211_commands {
- * until the channel switch event.
- * @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission
- * must be blocked on the current channel (before the channel switch
-- * operation).
-+ * operation). Also included in the channel switch started event if quiet
-+ * was requested by the AP.
- * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
- * for the time while performing a channel switch.
- * @NL80211_ATTR_CNTDWN_OFFS_BEACON: An array of offsets (u16) to the channel
-@@ -2527,6 +2569,33 @@ enum nl80211_commands {
- * override mask. Used with NL80211_ATTR_S1G_CAPABILITY in
- * NL80211_CMD_ASSOCIATE or NL80211_CMD_CONNECT.
+@@ -2627,17 +2593,8 @@ enum nl80211_commands {
+ * @NL80211_ATTR_COLOR_CHANGE_ELEMS: Nested set of attributes containing the IE
+ * information for the time while performing a color switch.
*
-+ * @NL80211_ATTR_SAE_PWE: Indicates the mechanism(s) allowed for SAE PWE
-+ * derivation in WPA3-Personal networks which are using SAE authentication.
-+ * This is a u8 attribute that encapsulates one of the values from
-+ * &enum nl80211_sae_pwe_mechanism.
-+ *
-+ * @NL80211_ATTR_SAR_SPEC: SAR power limitation specification when
-+ * used with %NL80211_CMD_SET_SAR_SPECS. The message contains fields
-+ * of %nl80211_sar_attrs which specifies the sar type and related
-+ * sar specs. Sar specs contains array of %nl80211_sar_specs_attrs.
-+ *
-+ * @NL80211_ATTR_RECONNECT_REQUESTED: flag attribute, used with deauth and
-+ * disassoc events to indicate that an immediate reconnect to the AP
-+ * is desired.
-+ *
-+ * @NL80211_ATTR_OBSS_COLOR_BITMAP: bitmap of the u64 BSS colors for the
-+ * %NL80211_CMD_OBSS_COLOR_COLLISION event.
-+ *
-+ * @NL80211_ATTR_COLOR_CHANGE_COUNT: u8 attribute specifying the number of TBTT's
-+ * until the color switch event.
-+ * @NL80211_ATTR_COLOR_CHANGE_COLOR: u8 attribute specifying the color that we are
-+ * switching to
-+ * @NL80211_ATTR_COLOR_CHANGE_ELEMS: Nested set of attributes containing the IE
-+ * information for the time while performing a color switch.
-+ *
+- * @NL80211_ATTR_MBSSID_CONFIG: Nested attribute for multiple BSSID
+- * advertisements (MBSSID) parameters in AP mode.
+- * Kernel uses this attribute to indicate the driver's support for MBSSID
+- * and enhanced multi-BSSID advertisements (EMA AP) to the userspace.
+- * Userspace should use this attribute to configure per interface MBSSID
+- * parameters.
+- * See &enum nl80211_mbssid_config_attributes for details.
+- *
+- * @NL80211_ATTR_MBSSID_ELEMS: Nested parameter to pass multiple BSSID elements.
+- * Mandatory parameter for the transmitting interface to enable MBSSID.
+- * Optional for the non-transmitting interfaces.
+ * @NL80211_ATTR_WIPHY_ANTENNA_GAIN: Configured antenna gain. Used to reduce
+ * transmit power to stay within regulatory limits. u32, dBi.
-+ *
+ *
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
- * @__NL80211_ATTR_AFTER_LAST: internal use
-@@ -3016,6 +3085,22 @@ enum nl80211_attrs {
- NL80211_ATTR_S1G_CAPABILITY,
- NL80211_ATTR_S1G_CAPABILITY_MASK,
+@@ -3142,8 +3099,7 @@ enum nl80211_attrs {
+ NL80211_ATTR_COLOR_CHANGE_COLOR,
+ NL80211_ATTR_COLOR_CHANGE_ELEMS,
-+ NL80211_ATTR_SAE_PWE,
-+
-+ NL80211_ATTR_RECONNECT_REQUESTED,
-+
-+ NL80211_ATTR_SAR_SPEC,
-+
-+ NL80211_ATTR_DISABLE_HE,
-+
-+ NL80211_ATTR_OBSS_COLOR_BITMAP,
-+
-+ NL80211_ATTR_COLOR_CHANGE_COUNT,
-+ NL80211_ATTR_COLOR_CHANGE_COLOR,
-+ NL80211_ATTR_COLOR_CHANGE_ELEMS,
-+
+- NL80211_ATTR_MBSSID_CONFIG,
+- NL80211_ATTR_MBSSID_ELEMS,
+ NL80211_ATTR_WIPHY_ANTENNA_GAIN,
-+
+
/* add attributes here, update the policy in nl80211.c */
- __NL80211_ATTR_AFTER_LAST,
-@@ -3613,6 +3698,8 @@ enum nl80211_mpath_info {
- * defined
- * @NL80211_BAND_IFTYPE_ATTR_HE_6GHZ_CAPA: HE 6GHz band capabilities (__le16),
- * given for all 6 GHz band channels
-+ * @NL80211_BAND_IFTYPE_ATTR_VENDOR_ELEMS: vendor element capabilities that are
-+ * advertised on this band/for this iftype (binary)
- * @__NL80211_BAND_IFTYPE_ATTR_AFTER_LAST: internal use
+@@ -4978,7 +4934,6 @@ enum nl80211_txrate_gi {
+ * @NL80211_BAND_60GHZ: around 60 GHz band (58.32 - 69.12 GHz)
+ * @NL80211_BAND_6GHZ: around 6 GHz band (5.9 - 7.2 GHz)
+ * @NL80211_BAND_S1GHZ: around 900MHz, supported by S1G PHYs
+- * @NL80211_BAND_LC: light communication band (placeholder)
+ * @NUM_NL80211_BANDS: number of bands, avoid using this in userspace
+ * since newer kernel versions may support more bands
*/
- enum nl80211_band_iftype_attr {
-@@ -3624,6 +3711,7 @@ enum nl80211_band_iftype_attr {
- NL80211_BAND_IFTYPE_ATTR_HE_CAP_MCS_SET,
- NL80211_BAND_IFTYPE_ATTR_HE_CAP_PPE,
- NL80211_BAND_IFTYPE_ATTR_HE_6GHZ_CAPA,
-+ NL80211_BAND_IFTYPE_ATTR_VENDOR_ELEMS,
+@@ -4988,7 +4943,6 @@ enum nl80211_band {
+ NL80211_BAND_60GHZ,
+ NL80211_BAND_6GHZ,
+ NL80211_BAND_S1GHZ,
+- NL80211_BAND_LC,
- /* keep last */
- __NL80211_BAND_IFTYPE_ATTR_AFTER_LAST,
-@@ -5896,6 +5984,22 @@ enum nl80211_feature_flags {
- * @NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP: Driver/device supports
- * unsolicited broadcast probe response transmission
+ NUM_NL80211_BANDS,
+ };
+@@ -6046,11 +6000,6 @@ enum nl80211_feature_flags {
+ * @NL80211_EXT_FEATURE_BSS_COLOR: The driver supports BSS color collision
+ * detection and change announcemnts.
*
-+ * @NL80211_EXT_FEATURE_BEACON_RATE_HE: Driver supports beacon rate
-+ * configuration (AP/mesh) with HE rates.
-+ *
-+ * @NL80211_EXT_FEATURE_SECURE_LTF: Device supports secure LTF measurement
-+ * exchange protocol.
-+ *
-+ * @NL80211_EXT_FEATURE_SECURE_RTT: Device supports secure RTT measurement
-+ * exchange protocol.
-+ *
-+ * @NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE: Device supports management
-+ * frame protection for all management frames exchanged during the
-+ * negotiation and range measurement procedure.
-+ *
-+ * @NL80211_EXT_FEATURE_BSS_COLOR: The driver supports BSS color collision
-+ * detection and change announcemnts.
-+ *
+- * @NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD: Driver running in AP mode supports
+- * FILS encryption and decryption for (Re)Association Request and Response
+- * frames. Userspace has to share FILS AAD details to the driver by using
+- * @NL80211_CMD_SET_FILS_AAD.
+- *
* @NUM_NL80211_EXT_FEATURES: number of extended features.
* @MAX_NL80211_EXT_FEATURES: highest extended feature index.
*/
-@@ -5956,6 +6060,11 @@ enum nl80211_ext_feature_index {
- NL80211_EXT_FEATURE_SAE_OFFLOAD_AP,
- NL80211_EXT_FEATURE_FILS_DISCOVERY,
- NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP,
-+ NL80211_EXT_FEATURE_BEACON_RATE_HE,
-+ NL80211_EXT_FEATURE_SECURE_LTF,
-+ NL80211_EXT_FEATURE_SECURE_RTT,
-+ NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE,
-+ NL80211_EXT_FEATURE_BSS_COLOR,
+@@ -6116,7 +6065,6 @@ enum nl80211_ext_feature_index {
+ NL80211_EXT_FEATURE_SECURE_RTT,
+ NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE,
+ NL80211_EXT_FEATURE_BSS_COLOR,
+- NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD,
/* add new features before the definition below */
NUM_NL80211_EXT_FEATURES,
-@@ -6253,11 +6362,13 @@ struct nl80211_vendor_cmd_info {
- * @NL80211_TDLS_PEER_HT: TDLS peer is HT capable.
- * @NL80211_TDLS_PEER_VHT: TDLS peer is VHT capable.
- * @NL80211_TDLS_PEER_WMM: TDLS peer is WMM capable.
-+ * @NL80211_TDLS_PEER_HE: TDLS peer is HE capable.
- */
- enum nl80211_tdls_peer_capability {
- NL80211_TDLS_PEER_HT = 1<<0,
- NL80211_TDLS_PEER_VHT = 1<<1,
- NL80211_TDLS_PEER_WMM = 1<<2,
-+ NL80211_TDLS_PEER_HE = 1<<3,
+@@ -7406,60 +7354,4 @@ enum nl80211_sar_specs_attrs {
+ NL80211_SAR_ATTR_SPECS_MAX = __NL80211_SAR_ATTR_SPECS_LAST - 1,
};
- /**
-@@ -6849,6 +6960,12 @@ enum nl80211_peer_measurement_ftm_capa {
- * if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
- * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
- * ranging will be used.
-+ * @NL80211_PMSR_FTM_REQ_ATTR_LMR_FEEDBACK: negotiate for LMR feedback. Only
-+ * valid if either %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED or
-+ * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set.
-+ * @NL80211_PMSR_FTM_REQ_ATTR_BSS_COLOR: optional. The BSS color of the
-+ * responder. Only valid if %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED
-+ * or %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED is set.
- *
- * @NUM_NL80211_PMSR_FTM_REQ_ATTR: internal
- * @NL80211_PMSR_FTM_REQ_ATTR_MAX: highest attribute number
-@@ -6867,6 +6984,8 @@ enum nl80211_peer_measurement_ftm_req {
- NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC,
- NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED,
- NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED,
-+ NL80211_PMSR_FTM_REQ_ATTR_LMR_FEEDBACK,
-+ NL80211_PMSR_FTM_REQ_ATTR_BSS_COLOR,
-
- /* keep last */
- NUM_NL80211_PMSR_FTM_REQ_ATTR,
-@@ -7124,4 +7243,115 @@ enum nl80211_unsol_bcast_probe_resp_attr
- NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_MAX =
- __NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST - 1
- };
-+
-+/**
-+ * enum nl80211_sae_pwe_mechanism - The mechanism(s) allowed for SAE PWE
-+ * derivation. Applicable only when WPA3-Personal SAE authentication is
-+ * used.
-+ *
-+ * @NL80211_SAE_PWE_UNSPECIFIED: not specified, used internally to indicate that
-+ * attribute is not present from userspace.
-+ * @NL80211_SAE_PWE_HUNT_AND_PECK: hunting-and-pecking loop only
-+ * @NL80211_SAE_PWE_HASH_TO_ELEMENT: hash-to-element only
-+ * @NL80211_SAE_PWE_BOTH: both hunting-and-pecking loop and hash-to-element
-+ * can be used.
-+ */
-+enum nl80211_sae_pwe_mechanism {
-+ NL80211_SAE_PWE_UNSPECIFIED,
-+ NL80211_SAE_PWE_HUNT_AND_PECK,
-+ NL80211_SAE_PWE_HASH_TO_ELEMENT,
-+ NL80211_SAE_PWE_BOTH,
-+};
-+
-+/**
-+ * enum nl80211_sar_type - type of SAR specs
-+ *
-+ * @NL80211_SAR_TYPE_POWER: power limitation specified in 0.25dBm unit
-+ *
-+ */
-+enum nl80211_sar_type {
-+ NL80211_SAR_TYPE_POWER,
-+
-+ /* add new type here */
-+
-+ /* Keep last */
-+ NUM_NL80211_SAR_TYPE,
-+};
-+
-+/**
-+ * enum nl80211_sar_attrs - Attributes for SAR spec
-+ *
-+ * @NL80211_SAR_ATTR_TYPE: the SAR type as defined in &enum nl80211_sar_type.
-+ *
-+ * @NL80211_SAR_ATTR_SPECS: Nested array of SAR power
-+ * limit specifications. Each specification contains a set
-+ * of %nl80211_sar_specs_attrs.
-+ *
-+ * For SET operation, it contains array of %NL80211_SAR_ATTR_SPECS_POWER
-+ * and %NL80211_SAR_ATTR_SPECS_RANGE_INDEX.
-+ *
-+ * For sar_capa dump, it contains array of
-+ * %NL80211_SAR_ATTR_SPECS_START_FREQ
-+ * and %NL80211_SAR_ATTR_SPECS_END_FREQ.
-+ *
-+ * @__NL80211_SAR_ATTR_LAST: Internal
-+ * @NL80211_SAR_ATTR_MAX: highest sar attribute
-+ *
-+ * These attributes are used with %NL80211_CMD_SET_SAR_SPEC
-+ */
-+enum nl80211_sar_attrs {
-+ __NL80211_SAR_ATTR_INVALID,
-+
-+ NL80211_SAR_ATTR_TYPE,
-+ NL80211_SAR_ATTR_SPECS,
-+
-+ __NL80211_SAR_ATTR_LAST,
-+ NL80211_SAR_ATTR_MAX = __NL80211_SAR_ATTR_LAST - 1,
-+};
-+
-+/**
-+ * enum nl80211_sar_specs_attrs - Attributes for SAR power limit specs
-+ *
-+ * @NL80211_SAR_ATTR_SPECS_POWER: Required (s32)value to specify the actual
-+ * power limit value in units of 0.25 dBm if type is
-+ * NL80211_SAR_TYPE_POWER. (i.e., a value of 44 represents 11 dBm).
-+ * 0 means userspace doesn't have SAR limitation on this associated range.
-+ *
-+ * @NL80211_SAR_ATTR_SPECS_RANGE_INDEX: Required (u32) value to specify the
-+ * index of exported freq range table and the associated power limitation
-+ * is applied to this range.
-+ *
-+ * Userspace isn't required to set all the ranges advertised by WLAN driver,
-+ * and userspace can skip some certain ranges. These skipped ranges don't
-+ * have SAR limitations, and they are same as setting the
-+ * %NL80211_SAR_ATTR_SPECS_POWER to any unreasonable high value because any
-+ * value higher than regulatory allowed value just means SAR power
-+ * limitation is removed, but it's required to set at least one range.
-+ * It's not allowed to set duplicated range in one SET operation.
-+ *
-+ * Every SET operation overwrites previous SET operation.
-+ *
-+ * @NL80211_SAR_ATTR_SPECS_START_FREQ: Required (u32) value to specify the start
-+ * frequency of this range edge when registering SAR capability to wiphy.
-+ * It's not a channel center frequency. The unit is kHz.
-+ *
-+ * @NL80211_SAR_ATTR_SPECS_END_FREQ: Required (u32) value to specify the end
-+ * frequency of this range edge when registering SAR capability to wiphy.
-+ * It's not a channel center frequency. The unit is kHz.
-+ *
-+ * @__NL80211_SAR_ATTR_SPECS_LAST: Internal
-+ * @NL80211_SAR_ATTR_SPECS_MAX: highest sar specs attribute
-+ */
-+enum nl80211_sar_specs_attrs {
-+ __NL80211_SAR_ATTR_SPECS_INVALID,
-+
-+ NL80211_SAR_ATTR_SPECS_POWER,
-+ NL80211_SAR_ATTR_SPECS_RANGE_INDEX,
-+ NL80211_SAR_ATTR_SPECS_START_FREQ,
-+ NL80211_SAR_ATTR_SPECS_END_FREQ,
-+
-+ __NL80211_SAR_ATTR_SPECS_LAST,
-+ NL80211_SAR_ATTR_SPECS_MAX = __NL80211_SAR_ATTR_SPECS_LAST - 1,
-+};
-+
+-/**
+- * enum nl80211_mbssid_config_attributes - multiple BSSID (MBSSID) and enhanced
+- * multi-BSSID advertisements (EMA) in AP mode.
+- * Kernel uses some of these attributes to advertise driver's support for
+- * MBSSID and EMA.
+- * Remaining attributes should be used by the userspace to configure the
+- * features.
+- *
+- * @__NL80211_MBSSID_CONFIG_ATTR_INVALID: Invalid
+- *
+- * @NL80211_MBSSID_CONFIG_ATTR_MAX_INTERFACES: Used by the kernel to advertise
+- * the maximum number of MBSSID interfaces supported by the driver.
+- * Driver should indicate MBSSID support by setting
+- * wiphy->mbssid_max_interfaces to a value more than or equal to 2.
+- *
+- * @NL80211_MBSSID_CONFIG_ATTR_MAX_EMA_PROFILE_PERIODICITY: Used by the kernel
+- * to advertise the maximum profile periodicity supported by the driver
+- * if EMA is enabled. Driver should indicate EMA support to the userspace
+- * by setting wiphy->ema_max_profile_periodicity to
+- * a non-zero value.
+- *
+- * @NL80211_MBSSID_CONFIG_ATTR_INDEX: Mandatory parameter to pass the index of
+- * this BSS (u8) in the multiple BSSID set.
+- * Value must be set to 0 for the transmitting interface and non-zero for
+- * all non-transmitting interfaces. The userspace will be responsible
+- * for using unique indices for the interfaces.
+- * Range: 0 to wiphy->mbssid_max_interfaces-1.
+- *
+- * @NL80211_MBSSID_CONFIG_ATTR_TX_IFINDEX: Mandatory parameter for
+- * a non-transmitted profile which provides the interface index (u32) of
+- * the transmitted profile. The value must match one of the interface
+- * indices advertised by the kernel. Optional if the interface being set up
+- * is the transmitting one, however, if provided then the value must match
+- * the interface index of the same.
+- *
+- * @NL80211_MBSSID_CONFIG_ATTR_EMA: Flag used to enable EMA AP feature.
+- * Setting this flag is permitted only if the driver advertises EMA support
+- * by setting wiphy->ema_max_profile_periodicity to non-zero.
+- *
+- * @__NL80211_MBSSID_CONFIG_ATTR_LAST: Internal
+- * @NL80211_MBSSID_CONFIG_ATTR_MAX: highest attribute
+- */
+-enum nl80211_mbssid_config_attributes {
+- __NL80211_MBSSID_CONFIG_ATTR_INVALID,
+-
+- NL80211_MBSSID_CONFIG_ATTR_MAX_INTERFACES,
+- NL80211_MBSSID_CONFIG_ATTR_MAX_EMA_PROFILE_PERIODICITY,
+- NL80211_MBSSID_CONFIG_ATTR_INDEX,
+- NL80211_MBSSID_CONFIG_ATTR_TX_IFINDEX,
+- NL80211_MBSSID_CONFIG_ATTR_EMA,
+-
+- /* keep last */
+- __NL80211_MBSSID_CONFIG_ATTR_LAST,
+- NL80211_MBSSID_CONFIG_ATTR_MAX = __NL80211_MBSSID_CONFIG_ATTR_LAST - 1,
+-};
+-
#endif /* __LINUX_NL80211_H */
+--- a/info.c
++++ b/info.c
+@@ -701,7 +701,6 @@ broken_combination:
+ ext_feat_print(tb, OPERATING_CHANNEL_VALIDATION, "Operating Channel Validation (OCV) support");
+ ext_feat_print(tb, 4WAY_HANDSHAKE_AP_PSK, "AP mode PSK offload support");
+ ext_feat_print(tb, BSS_COLOR, "BSS coloring support");
+- ext_feat_print(tb, FILS_CRYPTO_OFFLOAD, "FILS crypto offload");
+ }
+
+ if (tb_msg[NL80211_ATTR_COALESCE_RULE]) {
projects / openwrt / staging / lynxis.git / commitdiff