--- /dev/null
+#include "qcom-ipq8064-v1.0.dtsi"
+
+/ {
+ model = "Qualcomm IPQ8064/AP148";
+ compatible = "qcom,ipq8064-ap148", "qcom,ipq8064";
+
+ memory@0 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &gsbi4_serial;
+ mdio-gpio0 = &mdio0;
+ };
+
+ chosen {
+ linux,stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ pinmux@800000 {
+ i2c4_pins: i2c4_pinmux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ bias-disable;
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+ };
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
+ };
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+ };
+
+ gsbi5: gsbi@1a200000 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "ok";
+
+ spi4: spi@1a280000 {
+ status = "ok";
+ spi-max-frequency = <50000000>;
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 0>;
+
+ flash: m25p80@0 {
+ compatible = "s25fl256s1";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ linux,part-probe = "qcom-smem";
+ };
+ };
+ };
+
+ sata-phy@1b400000 {
+ status = "ok";
+ };
+
+ sata@29000000 {
+ status = "ok";
+ };
+
+ phy@100f8800 { /* USB3 port 1 HS phy */
+ status = "ok";
+ };
+
+ phy@100f8830 { /* USB3 port 1 SS phy */
+ status = "ok";
+ };
+
+ phy@110f8800 { /* USB3 port 0 HS phy */
+ status = "ok";
+ };
+
+ phy@110f8830 { /* USB3 port 0 SS phy */
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
+
+ pcie0: pci@1b500000 {
+ status = "ok";
+ phy-tx0-term-offset = <7>;
+ };
+
+ pcie1: pci@1b700000 {
+ status = "ok";
+ phy-tx0-term-offset = <7>;
+ };
+
+ nand@1ac00000 {
+ status = "ok";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+
+ linux,part-probe = "qcom-smem";
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ reg = <4>;
+ };
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
+
+&adm_dma {
+ status = "ok";
+};
--- /dev/null
+/dts-v1/;
+
+#include "skeleton.dtsi"
+#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/clock/qcom,lcc-ipq806x.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Qualcomm IPQ8064";
+ compatible = "qcom,ipq8064";
+ interrupt-parent = <&intc>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "qcom,krait";
+ enable-method = "qcom,kpss-acc-v1";
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc0>;
+ qcom,saw = <&saw0>;
+ clocks = <&kraitcc 0>, <&kraitcc 4>;
+ clock-names = "cpu", "l2";
+ clock-latency = <100000>;
+ cpu-supply = <&smb208_s2a>;
+ voltage-tolerance = <5>;
+ cooling-min-state = <0>;
+ cooling-max-state = <10>;
+ #cooling-cells = <2>;
+ cpu-idle-states = <&CPU_SPC>;
+ };
+
+ cpu1: cpu@1 {
+ compatible = "qcom,krait";
+ enable-method = "qcom,kpss-acc-v1";
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc1>;
+ qcom,saw = <&saw1>;
+ clocks = <&kraitcc 1>, <&kraitcc 4>;
+ clock-names = "cpu", "l2";
+ clock-latency = <100000>;
+ cpu-supply = <&smb208_s2b>;
+ cooling-min-state = <0>;
+ cooling-max-state = <10>;
+ #cooling-cells = <2>;
+ cpu-idle-states = <&CPU_SPC>;
+ };
+
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ qcom,saw = <&saw_l2>;
+ };
+
+ qcom,l2 {
+ qcom,l2-rates = <384000000 1000000000 1200000000>;
+ };
+
+ idle-states {
+ CPU_SPC: spc {
+ compatible = "qcom,idle-state-spc",
+ "arm,idle-state";
+ entry-latency-us = <400>;
+ exit-latency-us = <900>;
+ min-residency-us = <3000>;
+ };
+ };
+ };
+
+ thermal-zones {
+ cpu-thermal0 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&gcc 5>;
+ coefficients = <1132 0>;
+
+ trips {
+ cpu_alert0: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit0: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu-thermal1 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&gcc 6>;
+ coefficients = <1132 0>;
+
+ trips {
+ cpu_alert1: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit1: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu-thermal2 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&gcc 7>;
+ coefficients = <1199 0>;
+
+ trips {
+ cpu_alert2: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit2: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu-thermal3 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&gcc 8>;
+ coefficients = <1132 0>;
+
+ trips {
+ cpu_alert3: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit3: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
+ cpu-pmu {
+ compatible = "qcom,krait-pmu";
+ interrupts = <1 10 0x304>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ nss@40000000 {
+ reg = <0x40000000 0x1000000>;
+ no-map;
+ };
+
+ smem: smem@41000000 {
+ reg = <0x41000000 0x200000>;
+ no-map;
+ };
+ };
+
+ clocks {
+ cxo_board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ pxo_board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ sleep_clk: sleep_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ #clock-cells = <0>;
+ };
+ };
+
+ firmware {
+ scm {
+ compatible = "qcom,scm-apq8064";
+
+ clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>;
+ clock-names = "core";
+ };
+ };
+
+ kraitcc: clock-controller {
+ compatible = "qcom,krait-cc-v1";
+ #clock-cells = <1>;
+ };
+
+ qcom,pvs {
+ qcom,pvs-format-a;
+ qcom,speed0-pvs0-bin-v0 =
+ < 1400000000 1250000 >,
+ < 1200000000 1200000 >,
+ < 1000000000 1150000 >,
+ < 800000000 1100000 >,
+ < 600000000 1050000 >,
+ < 384000000 1000000 >;
+
+ qcom,speed0-pvs1-bin-v0 =
+ < 1400000000 1175000 >,
+ < 1200000000 1125000 >,
+ < 1000000000 1075000 >,
+ < 800000000 1025000 >,
+ < 600000000 975000 >,
+ < 384000000 925000 >;
+
+ qcom,speed0-pvs2-bin-v0 =
+ < 1400000000 1125000 >,
+ < 1200000000 1075000 >,
+ < 1000000000 1025000 >,
+ < 800000000 995000 >,
+ < 600000000 925000 >,
+ < 384000000 875000 >;
+
+ qcom,speed0-pvs3-bin-v0 =
+ < 1400000000 1050000 >,
+ < 1200000000 1000000 >,
+ < 1000000000 950000 >,
+ < 800000000 900000 >,
+ < 600000000 850000 >,
+ < 384000000 800000 >;
+ };
+
+ soc: soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "simple-bus";
+
+ lpass@28100000 {
+ compatible = "qcom,lpass-cpu";
+ status = "disabled";
+ clocks = <&lcc AHBIX_CLK>,
+ <&lcc MI2S_OSR_CLK>,
+ <&lcc MI2S_BIT_CLK>;
+ clock-names = "ahbix-clk",
+ "mi2s-osr-clk",
+ "mi2s-bit-clk";
+ interrupts = <0 85 1>;
+ interrupt-names = "lpass-irq-lpaif";
+ reg = <0x28100000 0x10000>;
+ reg-names = "lpass-lpaif";
+ };
+
+ qfprom: qfprom@700000 {
+ compatible = "qcom,qfprom", "syscon";
+ reg = <0x00700000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ tsens_calib: calib {
+ reg = <0x400 0x10>;
+ };
+ tsens_backup: backup_calib {
+ reg = <0x410 0x10>;
+ };
+ };
+
+ rpm@108000 {
+ compatible = "qcom,rpm-ipq8064";
+ reg = <0x108000 0x1000>;
+ qcom,ipc = <&l2cc 0x8 2>;
+
+ interrupts = <0 19 0>,
+ <0 21 0>,
+ <0 22 0>;
+ interrupt-names = "ack",
+ "err",
+ "wakeup";
+
+ /* clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+ clock-names = "ram"; */
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rpmcc: clock-controller {
+ compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
+ #clock-cells = <1>;
+ };
+
+ regulators {
+ compatible = "qcom,rpm-smb208-regulators";
+
+ smb208_s1a: s1a {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1150000>;
+
+ qcom,switch-mode-frequency = <1200000>;
+
+ };
+
+ smb208_s1b: s1b {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1150000>;
+
+ qcom,switch-mode-frequency = <1200000>;
+ };
+
+ smb208_s2a: s2a {
+ regulator-min-microvolt = < 800000>;
+ regulator-max-microvolt = <1250000>;
+
+ qcom,switch-mode-frequency = <1200000>;
+ };
+
+ smb208_s2b: s2b {
+ regulator-min-microvolt = < 800000>;
+ regulator-max-microvolt = <1250000>;
+
+ qcom,switch-mode-frequency = <1200000>;
+ };
+ };
+ };
+
+ rng@1a500000 {
+ compatible = "qcom,prng";
+ reg = <0x1a500000 0x200>;
+ clocks = <&gcc PRNG_CLK>;
+ clock-names = "core";
+ };
+
+ qcom_pinmux: pinmux@800000 {
+ compatible = "qcom,ipq8064-pinctrl";
+ reg = <0x800000 0x4000>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <0 16 0x4>;
+
+ pcie0_pins: pcie0_pinmux {
+ mux {
+ pins = "gpio3";
+ function = "pcie1_rst";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ pcie1_pins: pcie1_pinmux {
+ mux {
+ pins = "gpio48";
+ function = "pcie2_rst";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ pcie2_pins: pcie2_pinmux {
+ mux {
+ pins = "gpio63";
+ function = "pcie3_rst";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+ };
+ };
+
+ intc: interrupt-controller@2000000 {
+ compatible = "qcom,msm-qgic2";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x02000000 0x1000>,
+ <0x02002000 0x1000>;
+ };
+
+ timer@200a000 {
+ compatible = "qcom,kpss-timer", "qcom,msm-timer";
+ interrupts = <1 1 0x301>,
+ <1 2 0x301>,
+ <1 3 0x301>,
+ <1 4 0x301>,
+ <1 5 0x301>;
+ reg = <0x0200a000 0x100>;
+ clock-frequency = <25000000>,
+ <32768>;
+ clocks = <&sleep_clk>;
+ clock-names = "sleep";
+ cpu-offset = <0x80000>;
+ };
+
+ acc0: clock-controller@2088000 {
+ compatible = "qcom,kpss-acc-v1";
+ reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+ clock-output-names = "acpu0_aux";
+ };
+
+ acc1: clock-controller@2098000 {
+ compatible = "qcom,kpss-acc-v1";
+ reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+ clock-output-names = "acpu1_aux";
+ };
+
+ l2cc: clock-controller@2011000 {
+ compatible = "qcom,kpss-gcc", "syscon";
+ reg = <0x2011000 0x1000>;
+ clock-output-names = "acpu_l2_aux";
+ };
+
+ saw0: regulator@2089000 {
+ compatible = "qcom,saw2", "syscon";
+ reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+ regulator;
+ };
+
+ saw1: regulator@2099000 {
+ compatible = "qcom,saw2", "syscon";
+ reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+ regulator;
+ };
+
+ saw_l2: regulator@02012000 {
+ compatible = "qcom,saw2", "syscon";
+ reg = <0x02012000 0x1000>;
+ regulator;
+ };
+
+ sic_non_secure: sic-non-secure@12100000 {
+ compatible = "syscon";
+ reg = <0x12100000 0x10000>;
+ };
+
+ gsbi2: gsbi@12480000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ cell-index = <2>;
+ reg = <0x12480000 0x100>;
+ clocks = <&gcc GSBI2_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ syscon-tcsr = <&tcsr>;
+
+ uart2: serial@12490000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x12490000 0x1000>,
+ <0x12480000 0x1000>;
+ interrupts = <0 195 0x0>;
+ clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ i2c@124a0000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x124a0000 0x1000>;
+ interrupts = <0 196 0>;
+
+ clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ };
+
+ gsbi4: gsbi@16300000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ cell-index = <4>;
+ reg = <0x16300000 0x100>;
+ clocks = <&gcc GSBI4_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ syscon-tcsr = <&tcsr>;
+
+ gsbi4_serial: serial@16340000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x16340000 0x1000>,
+ <0x16300000 0x1000>;
+ interrupts = <0 152 0x0>;
+ clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ i2c@16380000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x16380000 0x1000>;
+ interrupts = <0 153 0>;
+
+ clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ gsbi5: gsbi@1a200000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ cell-index = <5>;
+ reg = <0x1a200000 0x100>;
+ clocks = <&gcc GSBI5_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ syscon-tcsr = <&tcsr>;
+
+ uart5: serial@1a240000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x1a240000 0x1000>,
+ <0x1a200000 0x1000>;
+ interrupts = <0 154 0x0>;
+ clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ i2c@1a280000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x1a280000 0x1000>;
+ interrupts = <0 155 0>;
+
+ clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi@1a280000 {
+ compatible = "qcom,spi-qup-v1.1.1";
+ reg = <0x1a280000 0x1000>;
+ interrupts = <0 155 0>;
+
+ clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ sata_phy: sata-phy@1b400000 {
+ compatible = "qcom,ipq806x-sata-phy";
+ reg = <0x1b400000 0x200>;
+
+ clocks = <&gcc SATA_PHY_CFG_CLK>;
+ clock-names = "cfg";
+
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ sata@29000000 {
+ compatible = "qcom,ipq806x-ahci", "generic-ahci";
+ reg = <0x29000000 0x180>;
+
+ interrupts = <0 209 0x0>;
+
+ clocks = <&gcc SFAB_SATA_S_H_CLK>,
+ <&gcc SATA_H_CLK>,
+ <&gcc SATA_A_CLK>,
+ <&gcc SATA_RXOOB_CLK>,
+ <&gcc SATA_PMALIVE_CLK>;
+ clock-names = "slave_face", "iface", "core",
+ "rxoob", "pmalive";
+
+ assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
+ assigned-clock-rates = <100000000>, <100000000>;
+
+ phys = <&sata_phy>;
+ phy-names = "sata-phy";
+ status = "disabled";
+ };
+
+ qcom,ssbi@500000 {
+ compatible = "qcom,ssbi";
+ reg = <0x00500000 0x1000>;
+ qcom,controller-type = "pmic-arbiter";
+ };
+
+ gcc: clock-controller@900000 {
+ compatible = "qcom,gcc-ipq8064";
+ reg = <0x00900000 0x4000>;
+ nvmem-cells = <&tsens_calib>, <&tsens_backup>;
+ nvmem-cell-names = "calib", "calib_backup";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ tcsr: syscon@1a400000 {
+ compatible = "qcom,tcsr-ipq8064", "syscon";
+ reg = <0x1a400000 0x100>;
+ };
+
+ lcc: clock-controller@28000000 {
+ compatible = "qcom,lcc-ipq8064";
+ reg = <0x28000000 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ sfpb_mutex_block: syscon@1200600 {
+ compatible = "syscon";
+ reg = <0x01200600 0x100>;
+ };
+
+ hs_phy_1: phy@100f8800 {
+ compatible = "qcom,dwc3-hs-usb-phy";
+ reg = <0x100f8800 0x30>;
+ clocks = <&gcc USB30_1_UTMI_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ ss_phy_1: phy@100f8830 {
+ compatible = "qcom,dwc3-ss-usb-phy";
+ reg = <0x100f8830 0x30>;
+ clocks = <&gcc USB30_1_MASTER_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ hs_phy_0: phy@110f8800 {
+ compatible = "qcom,dwc3-hs-usb-phy";
+ reg = <0x110f8800 0x30>;
+ clocks = <&gcc USB30_0_UTMI_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ ss_phy_0: phy@110f8830 {
+ compatible = "qcom,dwc3-ss-usb-phy";
+ reg = <0x110f8830 0x30>;
+ clocks = <&gcc USB30_0_MASTER_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ usb3_0: usb30@0 {
+ compatible = "qcom,dwc3";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&gcc USB30_0_MASTER_CLK>;
+ clock-names = "core";
+
+ syscon-tcsr = <&tcsr 0xb0 1>;
+
+ ranges;
+
+ status = "disabled";
+
+ dwc3@11000000 {
+ compatible = "snps,dwc3";
+ reg = <0x11000000 0xcd00>;
+ interrupts = <0 110 0x4>;
+ phys = <&hs_phy_0>, <&ss_phy_0>;
+ phy-names = "usb2-phy", "usb3-phy";
+ dr_mode = "host";
+ snps,dis_u3_susphy_quirk;
+ };
+ };
+
+ usb3_1: usb30@1 {
+ compatible = "qcom,dwc3";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&gcc USB30_1_MASTER_CLK>;
+ clock-names = "core";
+
+ syscon-tcsr = <&tcsr 0xb0 0>;
+
+ ranges;
+
+ status = "disabled";
+
+ dwc3@10000000 {
+ compatible = "snps,dwc3";
+ reg = <0x10000000 0xcd00>;
+ interrupts = <0 205 0x4>;
+ phys = <&hs_phy_1>, <&ss_phy_1>;
+ phy-names = "usb2-phy", "usb3-phy";
+ dr_mode = "host";
+ snps,dis_u3_susphy_quirk;
+ };
+ };
+
+ pcie0: pci@1b500000 {
+ compatible = "qcom,pcie-v0";
+ reg = <0x1b500000 0x1000
+ 0x1b502000 0x80
+ 0x1b600000 0x100
+ 0x0ff00000 0x100000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
+
+ interrupts = <GIC_SPI 35 IRQ_TYPE_NONE>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc PCIE_A_CLK>,
+ <&gcc PCIE_H_CLK>,
+ <&gcc PCIE_PHY_CLK>,
+ <&gcc PCIE_AUX_CLK>,
+ <&gcc PCIE_ALT_REF_CLK>;
+ clock-names = "core", "iface", "phy", "aux", "ref";
+
+ assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc PCIE_ACLK_RESET>,
+ <&gcc PCIE_HCLK_RESET>,
+ <&gcc PCIE_POR_RESET>,
+ <&gcc PCIE_PCI_RESET>,
+ <&gcc PCIE_PHY_RESET>,
+ <&gcc PCIE_EXT_RESET>;
+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+
+ perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+
+ status = "disabled";
+ };
+
+ pcie1: pci@1b700000 {
+ compatible = "qcom,pcie-v0";
+ reg = <0x1b700000 0x1000
+ 0x1b702000 0x80
+ 0x1b800000 0x100
+ 0x31f00000 0x100000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <1>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
+
+ interrupts = <GIC_SPI 57 IRQ_TYPE_NONE>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc PCIE_1_A_CLK>,
+ <&gcc PCIE_1_H_CLK>,
+ <&gcc PCIE_1_PHY_CLK>,
+ <&gcc PCIE_1_AUX_CLK>,
+ <&gcc PCIE_1_ALT_REF_CLK>;
+ clock-names = "core", "iface", "phy", "aux", "ref";
+
+ assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc PCIE_1_ACLK_RESET>,
+ <&gcc PCIE_1_HCLK_RESET>,
+ <&gcc PCIE_1_POR_RESET>,
+ <&gcc PCIE_1_PCI_RESET>,
+ <&gcc PCIE_1_PHY_RESET>,
+ <&gcc PCIE_1_EXT_RESET>;
+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+
+ perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+
+ status = "disabled";
+ };
+
+ pcie2: pci@1b900000 {
+ compatible = "qcom,pcie-v0";
+ reg = <0x1b900000 0x1000
+ 0x1b902000 0x80
+ 0x1ba00000 0x100
+ 0x35f00000 0x100000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <2>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
+
+ interrupts = <GIC_SPI 71 IRQ_TYPE_NONE>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc PCIE_2_A_CLK>,
+ <&gcc PCIE_2_H_CLK>,
+ <&gcc PCIE_2_PHY_CLK>,
+ <&gcc PCIE_2_AUX_CLK>,
+ <&gcc PCIE_2_ALT_REF_CLK>;
+ clock-names = "core", "iface", "phy", "aux", "ref";
+
+ assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc PCIE_2_ACLK_RESET>,
+ <&gcc PCIE_2_HCLK_RESET>,
+ <&gcc PCIE_2_POR_RESET>,
+ <&gcc PCIE_2_PCI_RESET>,
+ <&gcc PCIE_2_PHY_RESET>,
+ <&gcc PCIE_2_EXT_RESET>;
+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+ pinctrl-0 = <&pcie2_pins>;
+ pinctrl-names = "default";
+
+ perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
+
+ status = "disabled";
+ };
+
+ adm_dma: dma@18300000 {
+ compatible = "qcom,adm";
+ reg = <0x18300000 0x100000>;
+ interrupts = <0 170 0>;
+ #dma-cells = <1>;
+
+ clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
+ clock-names = "core", "iface";
+
+ resets = <&gcc ADM0_RESET>,
+ <&gcc ADM0_PBUS_RESET>,
+ <&gcc ADM0_C0_RESET>,
+ <&gcc ADM0_C1_RESET>,
+ <&gcc ADM0_C2_RESET>;
+ reset-names = "clk", "pbus", "c0", "c1", "c2";
+ qcom,ee = <0>;
+
+ status = "disabled";
+ };
+
+ nand@1ac00000 {
+ compatible = "qcom,ebi2-nandc";
+ reg = <0x1ac00000 0x800>;
+
+ clocks = <&gcc EBI2_CLK>,
+ <&gcc EBI2_AON_CLK>;
+ clock-names = "core", "aon";
+
+ dmas = <&adm_dma 3>;
+ dma-names = "rxtx";
+ qcom,cmd-crci = <15>;
+ qcom,data-crci = <3>;
+
+ status = "disabled";
+ };
+
+ nss_common: syscon@03000000 {
+ compatible = "syscon";
+ reg = <0x03000000 0x0000FFFF>;
+ };
+
+ qsgmii_csr: syscon@1bb00000 {
+ compatible = "syscon";
+ reg = <0x1bb00000 0x000001FF>;
+ };
+
+ gmac0: ethernet@37000000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac";
+ reg = <0x37000000 0x200000>;
+ interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE1_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE1_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ gmac1: ethernet@37200000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac";
+ reg = <0x37200000 0x200000>;
+ interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE2_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE2_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ gmac2: ethernet@37400000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac";
+ reg = <0x37400000 0x200000>;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE3_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE3_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ gmac3: ethernet@37600000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac";
+ reg = <0x37600000 0x200000>;
+ interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE4_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE4_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+ };
+
+ sfpb_mutex: sfpb-mutex {
+ compatible = "qcom,sfpb-mutex";
+ syscon = <&sfpb_mutex_block 4 4>;
+
+ #hwlock-cells = <1>;
+ };
+
+ smem {
+ compatible = "qcom,smem";
+ memory-region = <&smem>;
+ hwlocks = <&sfpb_mutex 3>;
+ };
+};
+++ /dev/null
-From eb694e964310ba402d6ff99f08e0ef78345e7397 Mon Sep 17 00:00:00 2001
-From: Thomas Pedersen <twp@codeaurora.org>
-Date: Mon, 16 May 2016 17:58:52 -0700
-Subject: [PATCH 03/37] arm: qcom: dts: ipq8064: Add ADM device node
-
-Original patch by Andy Gross.
-
-Signed-off-by: Andy Gross <agross@codeaurora.org>
-Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
----
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 21 +++++++++++++++++++++
- 1 file changed, 21 insertions(+)
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -1,9 +1,11 @@
- /dts-v1/;
-
- #include "skeleton.dtsi"
-+#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
- #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
- #include <dt-bindings/clock/qcom,lcc-ipq806x.h>
- #include <dt-bindings/soc/qcom,gsbi.h>
-+#include <dt-bindings/interrupt-controller/arm-gic.h>
-
- / {
- model = "Qualcomm IPQ8064";
-@@ -342,5 +344,24 @@
- #reset-cells = <1>;
- };
-
-+ adm_dma: dma@18300000 {
-+ compatible = "qcom,adm";
-+ reg = <0x18300000 0x100000>;
-+ interrupts = <GIC_SPI 170 IRQ_TYPE_NONE>;
-+ #dma-cells = <1>;
-+
-+ clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
-+ clock-names = "core", "iface";
-+
-+ resets = <&gcc ADM0_RESET>,
-+ <&gcc ADM0_PBUS_RESET>,
-+ <&gcc ADM0_C0_RESET>,
-+ <&gcc ADM0_C1_RESET>,
-+ <&gcc ADM0_C2_RESET>;
-+ reset-names = "clk", "pbus", "c0", "c1", "c2";
-+ qcom,ee = <0>;
-+
-+ status = "disabled";
-+ };
- };
- };
+++ /dev/null
-From c6d45af259eb4fb2a598c0396c6dd580b1658558 Mon Sep 17 00:00:00 2001
-From: Thomas Pedersen <twp@codeaurora.org>
-Date: Mon, 16 May 2016 17:58:53 -0700
-Subject: [PATCH 04/37] arm: qcom: dts: Add NAND controller node for ipq806x
-
-Original patch by Archit Taneja.
-
-Signed-off-by: Archit Taneja <architt@codeaurora.org>
-Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
----
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 17 +++++++++++++++++
- 1 file changed, 17 insertions(+)
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -363,5 +363,22 @@
-
- status = "disabled";
- };
-+
-+ nand@1ac00000 {
-+ compatible = "qcom,ipq806x-nand";
-+ reg = <0x1ac00000 0x800>;
-+
-+ clocks = <&gcc EBI2_CLK>,
-+ <&gcc EBI2_AON_CLK>;
-+ clock-names = "core", "aon";
-+
-+ dmas = <&adm_dma 3>;
-+ dma-names = "rxtx";
-+ qcom,cmd-crci = <15>;
-+ qcom,data-crci = <3>;
-+
-+ status = "disabled";
-+ };
-+
- };
- };
+++ /dev/null
-From f8d0939eca47f56449ec583810a6ff41a1caaa91 Mon Sep 17 00:00:00 2001
-From: Thomas Pedersen <twp@codeaurora.org>
-Date: Mon, 16 May 2016 17:58:54 -0700
-Subject: [PATCH 05/37] arm: qcom: dts: Enable NAND node on IPQ8064 AP148
- platform
-
-Original patch by Archit Taneja.
-
-Enable the NAND controller node on the AP148 platform. Provide pinmux
-information.
-
-Signed-off-by: Archit Taneja <architt@codeaurora.org>
-Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
----
- arch/arm/boot/dts/qcom-ipq8064-ap148.dts | 42 ++++++++++++++++++++++++++++++
- 1 file changed, 42 insertions(+)
-
---- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-+++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-@@ -38,6 +38,28 @@
- bias-none;
- };
- };
-+ nand_pins: nand_pins {
-+ mux {
-+ pins = "gpio34", "gpio35", "gpio36",
-+ "gpio37", "gpio38", "gpio39",
-+ "gpio40", "gpio41", "gpio42",
-+ "gpio43", "gpio44", "gpio45",
-+ "gpio46", "gpio47";
-+ function = "nand";
-+ drive-strength = <10>;
-+ bias-disable;
-+ };
-+ pullups {
-+ pins = "gpio39";
-+ bias-pull-up;
-+ };
-+ hold {
-+ pins = "gpio40", "gpio41", "gpio42",
-+ "gpio43", "gpio44", "gpio45",
-+ "gpio46", "gpio47";
-+ bias-bus-hold;
-+ };
-+ };
- };
-
- gsbi@16300000 {
-@@ -98,5 +120,25 @@
- ports-implemented = <0x1>;
- status = "ok";
- };
-+
-+ nand@1ac00000 {
-+ status = "ok";
-+
-+ pinctrl-0 = <&nand_pins>;
-+ pinctrl-names = "default";
-+
-+ nandcs@0 {
-+ compatible = "qcom,nandcs";
-+ reg = <0>;
-+
-+ nand-ecc-strength = <4>;
-+ nand-ecc-step-size = <512>;
-+ nand-bus-width = <8>;
-+ };
-+ };
- };
- };
-+
-+&adm_dma {
-+ status = "ok";
-+};
--- /dev/null
+From 8f68331e14dff9a101f2d0e1d6bec84a031f27ee Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Thu, 9 Mar 2017 11:03:18 +0100
+Subject: [PATCH 69/69] arm: boot: add dts files
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ arch/arm/boot/dts/Makefile | 8 ++++++++
+ 1 file changed, 8 insertions(+)
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -619,6 +619,14 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+ qcom-ipq4019-ap.dk01.1-c1.dtb \
+ qcom-ipq4019-ap.dk04.1-c1.dtb \
+ qcom-ipq8064-ap148.dtb \
++ qcom-ipq8064-c2600.dtb \
++ qcom-ipq8064-d7800.dtb \
++ qcom-ipq8064-db149.dtb \
++ qcom-ipq8064-ea8500.dtb \
++ qcom-ipq8064-r7500.dtb \
++ qcom-ipq8064-r7500v2.dtb \
++ qcom-ipq8065-nbg6817.dtb \
++ qcom-ipq8065-r7800.dtb \
+ qcom-msm8660-surf.dtb \
+ qcom-msm8960-cdp.dtb \
+ qcom-msm8974-lge-nexus5-hammerhead.dtb \
+++ /dev/null
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -619,6 +619,14 @@ dtb-$(CONFIG_ARCH_QCOM) += \
- qcom-ipq4019-ap.dk01.1-c1.dtb \
- qcom-ipq4019-ap.dk04.1-c1.dtb \
- qcom-ipq8064-ap148.dtb \
-+ qcom-ipq8064-c2600.dtb \
-+ qcom-ipq8064-d7800.dtb \
-+ qcom-ipq8064-db149.dtb \
-+ qcom-ipq8064-ea8500.dtb \
-+ qcom-ipq8064-r7500.dtb \
-+ qcom-ipq8064-r7500v2.dtb \
-+ qcom-ipq8065-nbg6817.dtb \
-+ qcom-ipq8065-r7800.dtb \
- qcom-msm8660-surf.dtb \
- qcom-msm8960-cdp.dtb \
- qcom-msm8974-lge-nexus5-hammerhead.dtb \
---- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-+++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-@@ -60,6 +60,25 @@
- bias-bus-hold;
- };
- };
-+
-+ mdio0_pins: mdio0_pins {
-+ mux {
-+ pins = "gpio0", "gpio1";
-+ function = "gpio";
-+ drive-strength = <8>;
-+ bias-disable;
-+ };
-+ };
-+
-+ rgmii2_pins: rgmii2_pins {
-+ mux {
-+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
-+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
-+ function = "rgmii2";
-+ drive-strength = <8>;
-+ bias-disable;
-+ };
-+ };
- };
-
- gsbi@16300000 {
-@@ -69,14 +88,12 @@
- status = "ok";
- };
-
-- i2c4: i2c@16380000 {
-- status = "ok";
--
-- clock-frequency = <200000>;
--
-- pinctrl-0 = <&i2c4_pins>;
-- pinctrl-names = "default";
-- };
-+ /*
-+ * The i2c device on gsbi4 should not be enabled.
-+ * On ipq806x designs gsbi4 i2c is meant for exclusive
-+ * RPM usage. Turning this on in kernel manifests as
-+ * i2c failure for the RPM.
-+ */
- };
-
- gsbi5: gsbi@1a200000 {
-@@ -99,15 +116,7 @@
- spi-max-frequency = <50000000>;
- reg = <0>;
-
-- partition@0 {
-- label = "rootfs";
-- reg = <0x0 0x1000000>;
-- };
--
-- partition@1 {
-- label = "scratch";
-- reg = <0x1000000 0x1000000>;
-- };
-+ linux,part-probe = "qcom-smem";
- };
- };
- };
-@@ -121,19 +130,102 @@
- status = "ok";
- };
-
-+ phy@100f8800 { /* USB3 port 1 HS phy */
-+ status = "ok";
-+ };
-+
-+ phy@100f8830 { /* USB3 port 1 SS phy */
-+ status = "ok";
-+ };
-+
-+ phy@110f8800 { /* USB3 port 0 HS phy */
-+ status = "ok";
-+ };
-+
-+ phy@110f8830 { /* USB3 port 0 SS phy */
-+ status = "ok";
-+ };
-+
-+ usb30@0 {
-+ status = "ok";
-+ };
-+
-+ usb30@1 {
-+ status = "ok";
-+ };
-+
-+ pcie0: pci@1b500000 {
-+ status = "ok";
-+ phy-tx0-term-offset = <7>;
-+ };
-+
-+ pcie1: pci@1b700000 {
-+ status = "ok";
-+ phy-tx0-term-offset = <7>;
-+ };
-+
- nand@1ac00000 {
- status = "ok";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
-- nandcs@0 {
-- compatible = "qcom,nandcs";
-+ nand-ecc-strength = <4>;
-+ nand-bus-width = <8>;
-+
-+ linux,part-probe = "qcom-smem";
-+ };
-+
-+ mdio0: mdio {
-+ compatible = "virtual,mdio-gpio";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
-+ pinctrl-0 = <&mdio0_pins>;
-+ pinctrl-names = "default";
-+
-+ phy0: ethernet-phy@0 {
-+ device_type = "ethernet-phy";
- reg = <0>;
-+ qca,ar8327-initvals = <
-+ 0x00004 0x7600000 /* PAD0_MODE */
-+ 0x00008 0x1000000 /* PAD5_MODE */
-+ 0x0000c 0x80 /* PAD6_MODE */
-+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
-+ 0x000e0 0xc74164de /* SGMII_CTRL */
-+ 0x0007c 0x4e /* PORT0_STATUS */
-+ 0x00094 0x4e /* PORT6_STATUS */
-+ >;
-+ };
-+
-+ phy4: ethernet-phy@4 {
-+ device_type = "ethernet-phy";
-+ reg = <4>;
-+ };
-+ };
-+
-+ gmac1: ethernet@37200000 {
-+ status = "ok";
-+ phy-mode = "rgmii";
-+ qcom,id = <1>;
-+
-+ pinctrl-0 = <&rgmii2_pins>;
-+ pinctrl-names = "default";
-+
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
-+ };
-+ };
-+
-+ gmac2: ethernet@37400000 {
-+ status = "ok";
-+ phy-mode = "sgmii";
-+ qcom,id = <2>;
-
-- nand-ecc-strength = <4>;
-- nand-ecc-step-size = <512>;
-- nand-bus-width = <8>;
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
- };
- };
- };
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -1,11 +1,13 @@
- /dts-v1/;
-
- #include "skeleton.dtsi"
--#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
- #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
-+#include <dt-bindings/mfd/qcom-rpm.h>
- #include <dt-bindings/clock/qcom,lcc-ipq806x.h>
- #include <dt-bindings/soc/qcom,gsbi.h>
-+#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
- #include <dt-bindings/interrupt-controller/arm-gic.h>
-+#include <dt-bindings/gpio/gpio.h>
-
- / {
- model = "Qualcomm IPQ8064";
-@@ -16,7 +18,7 @@
- #address-cells = <1>;
- #size-cells = <0>;
-
-- cpu@0 {
-+ cpu0: cpu@0 {
- compatible = "qcom,krait";
- enable-method = "qcom,kpss-acc-v1";
- device_type = "cpu";
-@@ -24,9 +26,18 @@
- next-level-cache = <&L2>;
- qcom,acc = <&acc0>;
- qcom,saw = <&saw0>;
-+ clocks = <&kraitcc 0>, <&kraitcc 4>;
-+ clock-names = "cpu", "l2";
-+ clock-latency = <100000>;
-+ cpu-supply = <&smb208_s2a>;
-+ voltage-tolerance = <5>;
-+ cooling-min-state = <0>;
-+ cooling-max-state = <10>;
-+ #cooling-cells = <2>;
-+ cpu-idle-states = <&CPU_SPC>;
- };
-
-- cpu@1 {
-+ cpu1: cpu@1 {
- compatible = "qcom,krait";
- enable-method = "qcom,kpss-acc-v1";
- device_type = "cpu";
-@@ -34,11 +45,120 @@
- next-level-cache = <&L2>;
- qcom,acc = <&acc1>;
- qcom,saw = <&saw1>;
-+ clocks = <&kraitcc 1>, <&kraitcc 4>;
-+ clock-names = "cpu", "l2";
-+ clock-latency = <100000>;
-+ cpu-supply = <&smb208_s2b>;
-+ cooling-min-state = <0>;
-+ cooling-max-state = <10>;
-+ #cooling-cells = <2>;
-+ cpu-idle-states = <&CPU_SPC>;
- };
-
- L2: l2-cache {
- compatible = "cache";
- cache-level = <2>;
-+ qcom,saw = <&saw_l2>;
-+ };
-+
-+ qcom,l2 {
-+ qcom,l2-rates = <384000000 1000000000 1200000000>;
-+ };
-+
-+ idle-states {
-+ CPU_SPC: spc {
-+ compatible = "qcom,idle-state-spc",
-+ "arm,idle-state";
-+ entry-latency-us = <400>;
-+ exit-latency-us = <900>;
-+ min-residency-us = <3000>;
-+ };
-+ };
-+ };
-+
-+ thermal-zones {
-+ cpu-thermal0 {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+
-+ thermal-sensors = <&gcc 5>;
-+ coefficients = <1132 0>;
-+
-+ trips {
-+ cpu_alert0: trip0 {
-+ temperature = <75000>;
-+ hysteresis = <2000>;
-+ type = "passive";
-+ };
-+ cpu_crit0: trip1 {
-+ temperature = <110000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+ };
-+ };
-+
-+ cpu-thermal1 {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+
-+ thermal-sensors = <&gcc 6>;
-+ coefficients = <1132 0>;
-+
-+ trips {
-+ cpu_alert1: trip0 {
-+ temperature = <75000>;
-+ hysteresis = <2000>;
-+ type = "passive";
-+ };
-+ cpu_crit1: trip1 {
-+ temperature = <110000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+ };
-+ };
-+
-+ cpu-thermal2 {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+
-+ thermal-sensors = <&gcc 7>;
-+ coefficients = <1199 0>;
-+
-+ trips {
-+ cpu_alert2: trip0 {
-+ temperature = <75000>;
-+ hysteresis = <2000>;
-+ type = "passive";
-+ };
-+ cpu_crit2: trip1 {
-+ temperature = <110000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+ };
-+ };
-+
-+ cpu-thermal3 {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+
-+ thermal-sensors = <&gcc 8>;
-+ coefficients = <1132 0>;
-+
-+ trips {
-+ cpu_alert3: trip0 {
-+ temperature = <75000>;
-+ hysteresis = <2000>;
-+ type = "passive";
-+ };
-+ cpu_crit3: trip1 {
-+ temperature = <110000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+ };
- };
- };
-
-@@ -57,7 +177,7 @@
- no-map;
- };
-
-- smem@41000000 {
-+ smem: smem@41000000 {
- reg = <0x41000000 0x200000>;
- no-map;
- };
-@@ -67,13 +187,13 @@
- cxo_board {
- compatible = "fixed-clock";
- #clock-cells = <0>;
-- clock-frequency = <19200000>;
-+ clock-frequency = <25000000>;
- };
-
- pxo_board {
- compatible = "fixed-clock";
- #clock-cells = <0>;
-- clock-frequency = <27000000>;
-+ clock-frequency = <25000000>;
- };
-
- sleep_clk: sleep_clk {
-@@ -83,6 +203,46 @@
- };
- };
-
-+ kraitcc: clock-controller {
-+ compatible = "qcom,krait-cc-v1";
-+ #clock-cells = <1>;
-+ };
-+
-+ qcom,pvs {
-+ qcom,pvs-format-a;
-+ qcom,speed0-pvs0-bin-v0 =
-+ < 1400000000 1250000 >,
-+ < 1200000000 1200000 >,
-+ < 1000000000 1150000 >,
-+ < 800000000 1100000 >,
-+ < 600000000 1050000 >,
-+ < 384000000 1000000 >;
-+
-+ qcom,speed0-pvs1-bin-v0 =
-+ < 1400000000 1175000 >,
-+ < 1200000000 1125000 >,
-+ < 1000000000 1075000 >,
-+ < 800000000 1025000 >,
-+ < 600000000 975000 >,
-+ < 384000000 925000 >;
-+
-+ qcom,speed0-pvs2-bin-v0 =
-+ < 1400000000 1125000 >,
-+ < 1200000000 1075000 >,
-+ < 1000000000 1025000 >,
-+ < 800000000 995000 >,
-+ < 600000000 925000 >,
-+ < 384000000 875000 >;
-+
-+ qcom,speed0-pvs3-bin-v0 =
-+ < 1400000000 1050000 >,
-+ < 1200000000 1000000 >,
-+ < 1000000000 950000 >,
-+ < 800000000 900000 >,
-+ < 600000000 850000 >,
-+ < 384000000 800000 >;
-+ };
-+
- soc: soc {
- #address-cells = <1>;
- #size-cells = <1>;
-@@ -104,6 +264,85 @@
- reg-names = "lpass-lpaif";
- };
-
-+ qfprom: qfprom@700000 {
-+ compatible = "qcom,qfprom", "syscon";
-+ reg = <0x00700000 0x1000>;
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ ranges;
-+
-+ tsens_calib: calib {
-+ reg = <0x400 0x10>;
-+ };
-+ tsens_backup: backup_calib {
-+ reg = <0x410 0x10>;
-+ };
-+ };
-+
-+ rpm@108000 {
-+ compatible = "qcom,rpm-ipq8064";
-+ reg = <0x108000 0x1000>;
-+ qcom,ipc = <&l2cc 0x8 2>;
-+
-+ interrupts = <0 19 0>,
-+ <0 21 0>,
-+ <0 22 0>;
-+ interrupt-names = "ack",
-+ "err",
-+ "wakeup";
-+
-+ clocks = <&gcc RPM_MSG_RAM_H_CLK>;
-+ clock-names = "ram";
-+
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ rpmcc: clock-controller {
-+ compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
-+ #clock-cells = <1>;
-+ };
-+
-+ regulators {
-+ compatible = "qcom,rpm-smb208-regulators";
-+
-+ smb208_s1a: s1a {
-+ regulator-min-microvolt = <1050000>;
-+ regulator-max-microvolt = <1150000>;
-+
-+ qcom,switch-mode-frequency = <1200000>;
-+
-+ };
-+
-+ smb208_s1b: s1b {
-+ regulator-min-microvolt = <1050000>;
-+ regulator-max-microvolt = <1150000>;
-+
-+ qcom,switch-mode-frequency = <1200000>;
-+ };
-+
-+ smb208_s2a: s2a {
-+ regulator-min-microvolt = < 800000>;
-+ regulator-max-microvolt = <1250000>;
-+
-+ qcom,switch-mode-frequency = <1200000>;
-+ };
-+
-+ smb208_s2b: s2b {
-+ regulator-min-microvolt = < 800000>;
-+ regulator-max-microvolt = <1250000>;
-+
-+ qcom,switch-mode-frequency = <1200000>;
-+ };
-+ };
-+ };
-+
-+ rng@1a500000 {
-+ compatible = "qcom,prng";
-+ reg = <0x1a500000 0x200>;
-+ clocks = <&gcc PRNG_CLK>;
-+ clock-names = "core";
-+ };
-+
- qcom_pinmux: pinmux@800000 {
- compatible = "qcom,ipq8064-pinctrl";
- reg = <0x800000 0x4000>;
-@@ -113,6 +352,34 @@
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <0 16 0x4>;
-+
-+ pcie0_pins: pcie0_pinmux {
-+ mux {
-+ pins = "gpio3";
-+ function = "pcie1_rst";
-+ drive-strength = <2>;
-+ bias-disable;
-+ };
-+ };
-+
-+ pcie1_pins: pcie1_pinmux {
-+ mux {
-+ pins = "gpio48";
-+ function = "pcie2_rst";
-+ drive-strength = <2>;
-+ bias-disable;
-+ };
-+ };
-+
-+ pcie2_pins: pcie2_pinmux {
-+ mux {
-+ pins = "gpio63";
-+ function = "pcie3_rst";
-+ drive-strength = <2>;
-+ bias-disable;
-+ output-low;
-+ };
-+ };
- };
-
- intc: interrupt-controller@2000000 {
-@@ -124,8 +391,7 @@
- };
-
- timer@200a000 {
-- compatible = "qcom,kpss-timer",
-- "qcom,kpss-wdt-ipq8064", "qcom,msm-timer";
-+ compatible = "qcom,kpss-timer", "qcom,msm-timer";
- interrupts = <1 1 0x301>,
- <1 2 0x301>,
- <1 3 0x301>,
-@@ -142,25 +408,44 @@
- acc0: clock-controller@2088000 {
- compatible = "qcom,kpss-acc-v1";
- reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
-+ clock-output-names = "acpu0_aux";
- };
-
- acc1: clock-controller@2098000 {
- compatible = "qcom,kpss-acc-v1";
- reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
-+ clock-output-names = "acpu1_aux";
- };
-
-+ l2cc: clock-controller@2011000 {
-+ compatible = "qcom,kpss-gcc", "syscon";
-+ reg = <0x2011000 0x1000>;
-+ clock-output-names = "acpu_l2_aux";
-+ };
-+
- saw0: regulator@2089000 {
-- compatible = "qcom,saw2";
-+ compatible = "qcom,saw2", "syscon";
- reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
- regulator;
- };
-
- saw1: regulator@2099000 {
-- compatible = "qcom,saw2";
-+ compatible = "qcom,saw2", "syscon";
- reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
- regulator;
- };
-
-+ saw_l2: regulator@02012000 {
-+ compatible = "qcom,saw2", "syscon";
-+ reg = <0x02012000 0x1000>;
-+ regulator;
-+ };
-+
-+ sic_non_secure: sic-non-secure@12100000 {
-+ compatible = "syscon";
-+ reg = <0x12100000 0x10000>;
-+ };
-+
- gsbi2: gsbi@12480000 {
- compatible = "qcom,gsbi-v1.0.0";
- cell-index = <2>;
-@@ -328,8 +613,12 @@
- gcc: clock-controller@900000 {
- compatible = "qcom,gcc-ipq8064";
- reg = <0x00900000 0x4000>;
-+ nvmem-cells = <&tsens_calib>, <&tsens_backup>;
-+ nvmem-cell-names = "calib", "calib_backup";
- #clock-cells = <1>;
- #reset-cells = <1>;
-+ #power-domain-cells = <1>;
-+ #thermal-sensor-cells = <1>;
- };
-
- tcsr: syscon@1a400000 {
-@@ -344,10 +633,259 @@
- #reset-cells = <1>;
- };
-
-+ sfpb_mutex_block: syscon@1200600 {
-+ compatible = "syscon";
-+ reg = <0x01200600 0x100>;
-+ };
-+
-+ hs_phy_1: phy@100f8800 {
-+ compatible = "qcom,dwc3-hs-usb-phy";
-+ reg = <0x100f8800 0x30>;
-+ clocks = <&gcc USB30_1_UTMI_CLK>;
-+ clock-names = "ref";
-+ #phy-cells = <0>;
-+
-+ status = "disabled";
-+ };
-+
-+ ss_phy_1: phy@100f8830 {
-+ compatible = "qcom,dwc3-ss-usb-phy";
-+ reg = <0x100f8830 0x30>;
-+ clocks = <&gcc USB30_1_MASTER_CLK>;
-+ clock-names = "ref";
-+ #phy-cells = <0>;
-+
-+ status = "disabled";
-+ };
-+
-+ hs_phy_0: phy@110f8800 {
-+ compatible = "qcom,dwc3-hs-usb-phy";
-+ reg = <0x110f8800 0x30>;
-+ clocks = <&gcc USB30_0_UTMI_CLK>;
-+ clock-names = "ref";
-+ #phy-cells = <0>;
-+
-+ status = "disabled";
-+ };
-+
-+ ss_phy_0: phy@110f8830 {
-+ compatible = "qcom,dwc3-ss-usb-phy";
-+ reg = <0x110f8830 0x30>;
-+ clocks = <&gcc USB30_0_MASTER_CLK>;
-+ clock-names = "ref";
-+ #phy-cells = <0>;
-+
-+ status = "disabled";
-+ };
-+
-+ usb3_0: usb30@0 {
-+ compatible = "qcom,dwc3";
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ clocks = <&gcc USB30_0_MASTER_CLK>;
-+ clock-names = "core";
-+
-+ syscon-tcsr = <&tcsr 0xb0 1>;
-+
-+ ranges;
-+
-+ status = "disabled";
-+
-+ dwc3@11000000 {
-+ compatible = "snps,dwc3";
-+ reg = <0x11000000 0xcd00>;
-+ interrupts = <0 110 0x4>;
-+ phys = <&hs_phy_0>, <&ss_phy_0>;
-+ phy-names = "usb2-phy", "usb3-phy";
-+ dr_mode = "host";
-+ snps,dis_u3_susphy_quirk;
-+ };
-+ };
-+
-+ usb3_1: usb30@1 {
-+ compatible = "qcom,dwc3";
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ clocks = <&gcc USB30_1_MASTER_CLK>;
-+ clock-names = "core";
-+
-+ syscon-tcsr = <&tcsr 0xb0 0>;
-+
-+ ranges;
-+
-+ status = "disabled";
-+
-+ dwc3@10000000 {
-+ compatible = "snps,dwc3";
-+ reg = <0x10000000 0xcd00>;
-+ interrupts = <0 205 0x4>;
-+ phys = <&hs_phy_1>, <&ss_phy_1>;
-+ phy-names = "usb2-phy", "usb3-phy";
-+ dr_mode = "host";
-+ snps,dis_u3_susphy_quirk;
-+ };
-+ };
-+
-+ pcie0: pci@1b500000 {
-+ compatible = "qcom,pcie-v0";
-+ reg = <0x1b500000 0x1000
-+ 0x1b502000 0x80
-+ 0x1b600000 0x100
-+ 0x0ff00000 0x100000>;
-+ reg-names = "dbi", "elbi", "parf", "config";
-+ device_type = "pci";
-+ linux,pci-domain = <0>;
-+ bus-range = <0x00 0xff>;
-+ num-lanes = <1>;
-+ #address-cells = <3>;
-+ #size-cells = <2>;
-+
-+ ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */
-+ 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
-+
-+ interrupts = <GIC_SPI 35 IRQ_TYPE_NONE>;
-+ interrupt-names = "msi";
-+ #interrupt-cells = <1>;
-+ interrupt-map-mask = <0 0 0 0x7>;
-+ interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-+ <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-+ <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-+ <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
-+
-+ clocks = <&gcc PCIE_A_CLK>,
-+ <&gcc PCIE_H_CLK>,
-+ <&gcc PCIE_PHY_CLK>,
-+ <&gcc PCIE_AUX_CLK>,
-+ <&gcc PCIE_ALT_REF_CLK>;
-+ clock-names = "core", "iface", "phy", "aux", "ref";
-+
-+ assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
-+ assigned-clock-rates = <100000000>;
-+
-+ resets = <&gcc PCIE_ACLK_RESET>,
-+ <&gcc PCIE_HCLK_RESET>,
-+ <&gcc PCIE_POR_RESET>,
-+ <&gcc PCIE_PCI_RESET>,
-+ <&gcc PCIE_PHY_RESET>,
-+ <&gcc PCIE_EXT_RESET>;
-+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
-+
-+ pinctrl-0 = <&pcie0_pins>;
-+ pinctrl-names = "default";
-+
-+ perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
-+
-+ status = "disabled";
-+ };
-+
-+ pcie1: pci@1b700000 {
-+ compatible = "qcom,pcie-v0";
-+ reg = <0x1b700000 0x1000
-+ 0x1b702000 0x80
-+ 0x1b800000 0x100
-+ 0x31f00000 0x100000>;
-+ reg-names = "dbi", "elbi", "parf", "config";
-+ device_type = "pci";
-+ linux,pci-domain = <1>;
-+ bus-range = <0x00 0xff>;
-+ num-lanes = <1>;
-+ #address-cells = <3>;
-+ #size-cells = <2>;
-+
-+ ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */
-+ 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
-+
-+ interrupts = <GIC_SPI 57 IRQ_TYPE_NONE>;
-+ interrupt-names = "msi";
-+ #interrupt-cells = <1>;
-+ interrupt-map-mask = <0 0 0 0x7>;
-+ interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-+ <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-+ <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-+ <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
-+
-+ clocks = <&gcc PCIE_1_A_CLK>,
-+ <&gcc PCIE_1_H_CLK>,
-+ <&gcc PCIE_1_PHY_CLK>,
-+ <&gcc PCIE_1_AUX_CLK>,
-+ <&gcc PCIE_1_ALT_REF_CLK>;
-+ clock-names = "core", "iface", "phy", "aux", "ref";
-+
-+ assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
-+ assigned-clock-rates = <100000000>;
-+
-+ resets = <&gcc PCIE_1_ACLK_RESET>,
-+ <&gcc PCIE_1_HCLK_RESET>,
-+ <&gcc PCIE_1_POR_RESET>,
-+ <&gcc PCIE_1_PCI_RESET>,
-+ <&gcc PCIE_1_PHY_RESET>,
-+ <&gcc PCIE_1_EXT_RESET>;
-+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
-+
-+ pinctrl-0 = <&pcie1_pins>;
-+ pinctrl-names = "default";
-+
-+ perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
-+
-+ status = "disabled";
-+ };
-+
-+ pcie2: pci@1b900000 {
-+ compatible = "qcom,pcie-v0";
-+ reg = <0x1b900000 0x1000
-+ 0x1b902000 0x80
-+ 0x1ba00000 0x100
-+ 0x35f00000 0x100000>;
-+ reg-names = "dbi", "elbi", "parf", "config";
-+ device_type = "pci";
-+ linux,pci-domain = <2>;
-+ bus-range = <0x00 0xff>;
-+ num-lanes = <1>;
-+ #address-cells = <3>;
-+ #size-cells = <2>;
-+
-+ ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */
-+ 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
-+
-+ interrupts = <GIC_SPI 71 IRQ_TYPE_NONE>;
-+ interrupt-names = "msi";
-+ #interrupt-cells = <1>;
-+ interrupt-map-mask = <0 0 0 0x7>;
-+ interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-+ <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-+ <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-+ <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
-+
-+ clocks = <&gcc PCIE_2_A_CLK>,
-+ <&gcc PCIE_2_H_CLK>,
-+ <&gcc PCIE_2_PHY_CLK>,
-+ <&gcc PCIE_2_AUX_CLK>,
-+ <&gcc PCIE_2_ALT_REF_CLK>;
-+ clock-names = "core", "iface", "phy", "aux", "ref";
-+
-+ assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
-+ assigned-clock-rates = <100000000>;
-+
-+ resets = <&gcc PCIE_2_ACLK_RESET>,
-+ <&gcc PCIE_2_HCLK_RESET>,
-+ <&gcc PCIE_2_POR_RESET>,
-+ <&gcc PCIE_2_PCI_RESET>,
-+ <&gcc PCIE_2_PHY_RESET>,
-+ <&gcc PCIE_2_EXT_RESET>;
-+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
-+
-+ pinctrl-0 = <&pcie2_pins>;
-+ pinctrl-names = "default";
-+
-+ perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
-+
-+ status = "disabled";
-+ };
-+
- adm_dma: dma@18300000 {
- compatible = "qcom,adm";
- reg = <0x18300000 0x100000>;
-- interrupts = <GIC_SPI 170 IRQ_TYPE_NONE>;
-+ interrupts = <0 170 0>;
- #dma-cells = <1>;
-
- clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
-@@ -365,7 +903,7 @@
- };
-
- nand@1ac00000 {
-- compatible = "qcom,ipq806x-nand";
-+ compatible = "qcom,ebi2-nandc";
- reg = <0x1ac00000 0x800>;
-
- clocks = <&gcc EBI2_CLK>,
-@@ -380,5 +918,103 @@
- status = "disabled";
- };
-
-+ nss_common: syscon@03000000 {
-+ compatible = "syscon";
-+ reg = <0x03000000 0x0000FFFF>;
-+ };
-+
-+ qsgmii_csr: syscon@1bb00000 {
-+ compatible = "syscon";
-+ reg = <0x1bb00000 0x000001FF>;
-+ };
-+
-+ gmac0: ethernet@37000000 {
-+ device_type = "network";
-+ compatible = "qcom,ipq806x-gmac";
-+ reg = <0x37000000 0x200000>;
-+ interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "macirq";
-+
-+ qcom,nss-common = <&nss_common>;
-+ qcom,qsgmii-csr = <&qsgmii_csr>;
-+
-+ clocks = <&gcc GMAC_CORE1_CLK>;
-+ clock-names = "stmmaceth";
-+
-+ resets = <&gcc GMAC_CORE1_RESET>;
-+ reset-names = "stmmaceth";
-+
-+ status = "disabled";
-+ };
-+
-+ gmac1: ethernet@37200000 {
-+ device_type = "network";
-+ compatible = "qcom,ipq806x-gmac";
-+ reg = <0x37200000 0x200000>;
-+ interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "macirq";
-+
-+ qcom,nss-common = <&nss_common>;
-+ qcom,qsgmii-csr = <&qsgmii_csr>;
-+
-+ clocks = <&gcc GMAC_CORE2_CLK>;
-+ clock-names = "stmmaceth";
-+
-+ resets = <&gcc GMAC_CORE2_RESET>;
-+ reset-names = "stmmaceth";
-+
-+ status = "disabled";
-+ };
-+
-+ gmac2: ethernet@37400000 {
-+ device_type = "network";
-+ compatible = "qcom,ipq806x-gmac";
-+ reg = <0x37400000 0x200000>;
-+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "macirq";
-+
-+ qcom,nss-common = <&nss_common>;
-+ qcom,qsgmii-csr = <&qsgmii_csr>;
-+
-+ clocks = <&gcc GMAC_CORE3_CLK>;
-+ clock-names = "stmmaceth";
-+
-+ resets = <&gcc GMAC_CORE3_RESET>;
-+ reset-names = "stmmaceth";
-+
-+ status = "disabled";
-+ };
-+
-+ gmac3: ethernet@37600000 {
-+ device_type = "network";
-+ compatible = "qcom,ipq806x-gmac";
-+ reg = <0x37600000 0x200000>;
-+ interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "macirq";
-+
-+ qcom,nss-common = <&nss_common>;
-+ qcom,qsgmii-csr = <&qsgmii_csr>;
-+
-+ clocks = <&gcc GMAC_CORE4_CLK>;
-+ clock-names = "stmmaceth";
-+
-+ resets = <&gcc GMAC_CORE4_RESET>;
-+ reset-names = "stmmaceth";
-+
-+ status = "disabled";
-+ };
-+ };
-+
-+ sfpb_mutex: sfpb-mutex {
-+ compatible = "qcom,sfpb-mutex";
-+ syscon = <&sfpb_mutex_block 4 4>;
-+
-+ #hwlock-cells = <1>;
-+ };
-+
-+ smem {
-+ compatible = "qcom,smem";
-+ memory-region = <&smem>;
-+ hwlocks = <&sfpb_mutex 3>;
- };
- };
projects / openwrt / staging / nbd.git / commitdiff