--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mtd/partitions/uimage.h>
+
+/ {
+ compatible = "dlink,covr-p2500-a1", "qca,qca9563";
+ model = "D-Link COVR-P2500 A1";
+
+ aliases {
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_red;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_red;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&jtag_disable_pins>;
+
+ lan {
+ label = "green:lan";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_green: power_green {
+ label = "green:power";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wlan5g {
+ label = "green:wlan5g";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0radio";
+ };
+
+ led_power_red: power_red {
+ label = "red:power";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2g {
+ label = "green:wlan2g";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1radio";
+ };
+ };
+
+ virtual_flash {
+ compatible = "mtd-concat";
+
+ devices = <&fwconcat0 &fwconcat1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ compatible = "openwrt,uimage", "denx,uimage";
+ openwrt,ih-magic = <0x68737173>;
+ label = "firmware";
+ reg = <0x0 0x0>;
+ };
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ fwconcat0: partition@50000 {
+ label = "fwconcat0";
+ reg = <0x50000 0xe30000>;
+ };
+
+ partition@e80000 {
+ label = "loader";
+ reg = <0xe80000 0x10000>;
+ read-only;
+ };
+
+ fwconcat1: partition@e90000 {
+ label = "fwconcat1";
+ reg = <0xe90000 0x160000>;
+ };
+
+ art: partition@ff0000 {
+ label = "art";
+ reg = <0xff0000 0x10000>;
+ read-only;
+
+ compatible = "nvmem-cells";
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ calibration_ath9k: calibration@1000 {
+ reg = <0x1000 0x440>;
+ };
+
+ precalibration_ath10k: pre-calibration@5000 {
+ reg = <0x5000 0x2f20>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+
+ wifi@0,0 {
+ compatible = "qcom,ath10k";
+ reg = <0 0 0 0 0>;
+
+ nvmem-cells = <&precalibration_ath10k>;
+ nvmem-cell-names = "pre-calibration";
+ };
+};
+
+&gpio {
+ phy-reset {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "phy-reset";
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ phy-mode = "sgmii";
+ qca,mib-poll-interval = <500>;
+
+ qca,ar8327-initvals = <
+ 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+ 0x10 0x81000080 /* POWER_ON_STRAP */
+ 0x50 0xcc35cc35 /* LED_CTRL0 */
+ 0x54 0xcb37cb37 /* LED_CTRL1 */
+ 0x58 0x00000000 /* LED_CTRL2 */
+ 0x5c 0x00f3cf00 /* LED_CTRL3 */
+ 0x7c 0x0000007e /* PORT0_STATUS */
+ >;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ pll-data = <0x03000101 0x00000101 0x00001919>;
+
+ phy-mode = "sgmii";
+ phy-handle = <&phy0>;
+};
+
+&wmac {
+ status = "okay";
+
+ nvmem-cells = <&calibration_ath9k>;
+ nvmem-cell-names = "calibration";
+};
-rm $@-empty.bin
endef
+define Build/dlink-sge-signature
+ ( \
+ crc=$$(gzip -c $@ | tail -c 8 | od -An -tx4 --endian little | cut -d " " -f2); \
+ cat $@; \
+ $(MKHASH) md5 $@ ; \
+ echo $(1); \
+ echo -n $$crc; \
+ ) > $@.new
+ mv $@.new $@
+endef
+
define Build/edimax-headers
$(eval edimax_magic=$(word 1,$(1)))
$(eval edimax_model=$(word 2,$(1)))
endef
TARGET_DEVICES += devolo_magic-2-wifi
+define Device/dlink_covr-p2500-a1
+ $(Device/loader-okli-uimage)
+ SOC := qca9563
+ DEVICE_VENDOR := D-Link
+ DEVICE_MODEL := COVR-P2500
+ DEVICE_VARIANT := A1
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+ LOADER_FLASH_OFFS := 0x050000
+ LOADER_KERNEL_MAGIC := 0x68737173
+ KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x68737173
+ IMAGE_SIZE := 14528k
+ IMAGES += factory.bin recovery.bin
+ IMAGE/recovery.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs | check-size | pad-to 14528k | \
+ append-loader-okli-uimage $(1) | pad-to 15616k
+ IMAGE/factory.bin := $$(IMAGE/recovery.bin) | \
+ dlink-sge-image COVR-P2500 | dlink-sge-signature COVR-P2500
+endef
+TARGET_DEVICES += dlink_covr-p2500-a1
+
define Device/dlink_dap-13xx
SOC := qca9533
DEVICE_VENDOR := D-Link
projects / openwrt / staging / dangole.git / commitdiff