#define IRQ_U300_NFIF 45
#define IRQ_U300_NFIF2 46
#define IRQ_U300_SYSCON_PLL_LOCK 47
-#define U300_NR_IRQS 48
+#define U300_VIC_IRQS_END 48
#endif
-#define NR_IRQS U300_NR_IRQS
+/* Maximum 8*7 GPIO lines */
+#ifdef CONFIG_GPIO_U300
+#define IRQ_U300_GPIO_BASE (U300_VIC_IRQS_END)
+#define IRQ_U300_GPIO_END (IRQ_U300_GPIO_BASE + 56)
+#else
+#define IRQ_U300_GPIO_END (U300_VIC_IRQS_END)
+#endif
+
- /* Optional AB3550 mixsig chip */
- #ifdef CONFIG_AB3550_CORE
- #define IRQ_AB3550_BASE (IRQ_U300_GPIO_END)
- #define IRQ_AB3550_END (IRQ_AB3550_BASE + 38)
- #else
- #define IRQ_AB3550_END (IRQ_U300_GPIO_END)
- #endif
-
- #define NR_IRQS (IRQ_AB3550_END)
++#define NR_IRQS (IRQ_U300_GPIO_END)
#endif
if (cpu_is_u5500())
db5500_prcmu_early_init();
if (cpu_is_u8500())
- prcmu_early_init();
+ db8500_prcmu_early_init();
clk_init();
}
-
-#ifdef CONFIG_CACHE_L2X0
-static inline void ux500_cache_wait(void __iomem *reg, unsigned long mask)
-{
- /* wait for the operation to complete */
- while (readl_relaxed(reg) & mask)
- ;
-}
-
-static inline void ux500_cache_sync(void)
-{
- void __iomem *base = l2x0_base;
-
- writel_relaxed(0, base + L2X0_CACHE_SYNC);
- ux500_cache_wait(base + L2X0_CACHE_SYNC, 1);
-}
-
-/*
- * The L2 cache cannot be turned off in the non-secure world.
- * Dummy until a secure service is in place.
- */
-static void ux500_l2x0_disable(void)
-{
-}
-
-/*
- * This is only called when doing a kexec, just after turning off the L2
- * and L1 cache, and it is surrounded by a spinlock in the generic version.
- * However, we're not really turning off the L2 cache right now and the
- * PL310 does not support exclusive accesses (used to implement the spinlock).
- * So, the invalidation needs to be done without the spinlock.
- */
-static void ux500_l2x0_inv_all(void)
-{
- void __iomem *base = l2x0_base;
- uint32_t l2x0_way_mask = (1<<16) - 1; /* Bitmask of active ways */
-
- /* invalidate all ways */
- writel_relaxed(l2x0_way_mask, base + L2X0_INV_WAY);
- ux500_cache_wait(base + L2X0_INV_WAY, l2x0_way_mask);
- ux500_cache_sync();
-}
-
-static int ux500_l2x0_init(void)
-{
- if (cpu_is_u5500())
- l2x0_base = __io_address(U5500_L2CC_BASE);
- else if (cpu_is_u8500())
- l2x0_base = __io_address(U8500_L2CC_BASE);
- else
- ux500_unknown_soc();
-
- /* 64KB way size, 8 way associativity, force WA */
- l2x0_init(l2x0_base, 0x3e060000, 0xc0000fff);
-
- /* Override invalidate function */
- outer_cache.disable = ux500_l2x0_disable;
- outer_cache.inv_all = ux500_l2x0_inv_all;
-
- return 0;
-}
-early_initcall(ux500_l2x0_init);
-#endif
-
-static void __init ux500_timer_init(void)
-{
-#ifdef CONFIG_LOCAL_TIMERS
- /* Setup the local timer base */
- if (cpu_is_u5500())
- twd_base = __io_address(U5500_TWD_BASE);
- else if (cpu_is_u8500())
- twd_base = __io_address(U8500_TWD_BASE);
- else
- ux500_unknown_soc();
-#endif
- if (cpu_is_u5500())
- mtu_base = __io_address(U5500_MTU0_BASE);
- else if (cpu_is_u8500ed())
- mtu_base = __io_address(U8500_MTU0_BASE_ED);
- else if (cpu_is_u8500())
- mtu_base = __io_address(U8500_MTU0_BASE);
- else
- ux500_unknown_soc();
-
- nmdk_timer_init();
-}
-
-struct sys_timer ux500_timer = {
- .init = ux500_timer_init,
-};
The Intel Tunnel Creek processor has 5 GPIOs powered by the
core power rail and 9 from suspend power supply.
+config GPIO_U300
+ bool "ST-Ericsson U300 COH 901 335/571 GPIO"
+ depends on GPIOLIB && ARCH_U300
+ help
+ Say yes here to support GPIO interface on ST-Ericsson U300.
+ The names of the two IP block variants supported are
+ COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
+ ports of 8 GPIO pins each.
+
config GPIO_VX855
tristate "VIA VX855/VX875 GPIO"
- depends on MFD_SUPPORT && PCI
+ depends on PCI
select MFD_CORE
select MFD_VX855
help
projects / openwrt / staging / blogic.git / commitdiff