extern atomic_t ppc_n_lost_interrupts;
-#ifdef CONFIG_PPC_MERGE
-
/* This number is used when no interrupt has been assigned */
#define NO_IRQ (0)
return irq;
}
-
-#else /* CONFIG_PPC_MERGE */
-
-/* This number is used when no interrupt has been assigned */
-#define NO_IRQ (-1)
-#define NO_IRQ_IGNORE (-2)
-
-
-/*
- * These constants are used for passing information about interrupt
- * signal polarity and level/edge sensing to the low-level PIC chip
- * drivers.
- */
-#define IRQ_SENSE_MASK 0x1
-#define IRQ_SENSE_LEVEL 0x1 /* interrupt on active level */
-#define IRQ_SENSE_EDGE 0x0 /* interrupt triggered by edge */
-
-#define IRQ_POLARITY_MASK 0x2
-#define IRQ_POLARITY_POSITIVE 0x2 /* high level or low->high edge */
-#define IRQ_POLARITY_NEGATIVE 0x0 /* low level or high->low edge */
-
-
-#if defined(CONFIG_40x)
-#include <asm/ibm4xx.h>
-
-#ifndef NR_BOARD_IRQS
-#define NR_BOARD_IRQS 0
-#endif
-
-#ifndef UIC_WIDTH /* Number of interrupts per device */
-#define UIC_WIDTH 32
-#endif
-
-#ifndef NR_UICS /* number of UIC devices */
-#define NR_UICS 1
-#endif
-
-#if defined (CONFIG_403)
-/*
- * The PowerPC 403 cores' Asynchronous Interrupt Controller (AIC) has
- * 32 possible interrupts, a majority of which are not implemented on
- * all cores. There are six configurable, external interrupt pins and
- * there are eight internal interrupts for the on-chip serial port
- * (SPU), DMA controller, and JTAG controller.
- *
- */
-
-#define NR_AIC_IRQS 32
-#define NR_IRQS (NR_AIC_IRQS + NR_BOARD_IRQS)
-
-#elif !defined (CONFIG_403)
-
-/*
- * The PowerPC 405 cores' Universal Interrupt Controller (UIC) has 32
- * possible interrupts as well. There are seven, configurable external
- * interrupt pins and there are 17 internal interrupts for the on-chip
- * serial port, DMA controller, on-chip Ethernet controller, PCI, etc.
- *
- */
-
-
-#define NR_UIC_IRQS UIC_WIDTH
-#define NR_IRQS ((NR_UIC_IRQS * NR_UICS) + NR_BOARD_IRQS)
-#endif
-
-#elif defined(CONFIG_44x)
-#include <asm/ibm44x.h>
-
-#define NR_UIC_IRQS 32
-#define NR_IRQS ((NR_UIC_IRQS * NR_UICS) + NR_BOARD_IRQS)
-
-#elif defined(CONFIG_8xx)
-
-/* Now include the board configuration specific associations.
-*/
-#include <asm/mpc8xx.h>
-
-/* The MPC8xx cores have 16 possible interrupts. There are eight
- * possible level sensitive interrupts assigned and generated internally
- * from such devices as CPM, PCMCIA, RTC, PIT, TimeBase and Decrementer.
- * There are eight external interrupts (IRQs) that can be configured
- * as either level or edge sensitive.
- *
- * On some implementations, there is also the possibility of an 8259
- * through the PCI and PCI-ISA bridges.
- *
- * We are "flattening" the interrupt vectors of the cascaded CPM
- * and 8259 interrupt controllers so that we can uniquely identify
- * any interrupt source with a single integer.
- */
-#define NR_SIU_INTS 16
-#define NR_CPM_INTS 32
-#ifndef NR_8259_INTS
-#define NR_8259_INTS 0
-#endif
-
-#define SIU_IRQ_OFFSET 0
-#define CPM_IRQ_OFFSET (SIU_IRQ_OFFSET + NR_SIU_INTS)
-#define I8259_IRQ_OFFSET (CPM_IRQ_OFFSET + NR_CPM_INTS)
-
-#define NR_IRQS (NR_SIU_INTS + NR_CPM_INTS + NR_8259_INTS)
-
-/* These values must be zero-based and map 1:1 with the SIU configuration.
- * They are used throughout the 8xx I/O subsystem to generate
- * interrupt masks, flags, and other control patterns. This is why the
- * current kernel assumption of the 8259 as the base controller is such
- * a pain in the butt.
- */
-#define SIU_IRQ0 (0) /* Highest priority */
-#define SIU_LEVEL0 (1)
-#define SIU_IRQ1 (2)
-#define SIU_LEVEL1 (3)
-#define SIU_IRQ2 (4)
-#define SIU_LEVEL2 (5)
-#define SIU_IRQ3 (6)
-#define SIU_LEVEL3 (7)
-#define SIU_IRQ4 (8)
-#define SIU_LEVEL4 (9)
-#define SIU_IRQ5 (10)
-#define SIU_LEVEL5 (11)
-#define SIU_IRQ6 (12)
-#define SIU_LEVEL6 (13)
-#define SIU_IRQ7 (14)
-#define SIU_LEVEL7 (15)
-
-#define MPC8xx_INT_FEC1 SIU_LEVEL1
-#define MPC8xx_INT_FEC2 SIU_LEVEL3
-
-#define MPC8xx_INT_SCC1 (CPM_IRQ_OFFSET + CPMVEC_SCC1)
-#define MPC8xx_INT_SCC2 (CPM_IRQ_OFFSET + CPMVEC_SCC2)
-#define MPC8xx_INT_SCC3 (CPM_IRQ_OFFSET + CPMVEC_SCC3)
-#define MPC8xx_INT_SCC4 (CPM_IRQ_OFFSET + CPMVEC_SCC4)
-#define MPC8xx_INT_SMC1 (CPM_IRQ_OFFSET + CPMVEC_SMC1)
-#define MPC8xx_INT_SMC2 (CPM_IRQ_OFFSET + CPMVEC_SMC2)
-
-/* The internal interrupts we can configure as we see fit.
- * My personal preference is CPM at level 2, which puts it above the
- * MBX PCI/ISA/IDE interrupts.
- */
-#ifndef PIT_INTERRUPT
-#define PIT_INTERRUPT SIU_LEVEL0
-#endif
-#ifndef CPM_INTERRUPT
-#define CPM_INTERRUPT SIU_LEVEL2
-#endif
-#ifndef PCMCIA_INTERRUPT
-#define PCMCIA_INTERRUPT SIU_LEVEL6
-#endif
-#ifndef DEC_INTERRUPT
-#define DEC_INTERRUPT SIU_LEVEL7
-#endif
-
-/* Some internal interrupt registers use an 8-bit mask for the interrupt
- * level instead of a number.
- */
-#define mk_int_int_mask(IL) (1 << (7 - (IL/2)))
-
-#else /* CONFIG_40x + CONFIG_8xx */
-/*
- * this is the # irq's for all ppc arch's (pmac/chrp/prep)
- * so it is the max of them all
- */
-#define NR_IRQS 256
-#define __DO_IRQ_CANON 1
-
-#ifndef CONFIG_8260
-
-#define NUM_8259_INTERRUPTS 16
-
-#else /* CONFIG_8260 */
-
-/* The 8260 has an internal interrupt controller with a maximum of
- * 64 IRQs. We will use NR_IRQs from above since it is large enough.
- * Don't be confused by the 8260 documentation where they list an
- * "interrupt number" and "interrupt vector". We are only interested
- * in the interrupt vector. There are "reserved" holes where the
- * vector number increases, but the interrupt number in the table does not.
- * (Document errata updates have fixed this...make sure you have up to
- * date processor documentation -- Dan).
- */
-
-#ifndef CPM_IRQ_OFFSET
-#define CPM_IRQ_OFFSET 0
-#endif
-
-#define NR_CPM_INTS 64
-
-#define SIU_INT_ERROR ((uint)0x00 + CPM_IRQ_OFFSET)
-#define SIU_INT_I2C ((uint)0x01 + CPM_IRQ_OFFSET)
-#define SIU_INT_SPI ((uint)0x02 + CPM_IRQ_OFFSET)
-#define SIU_INT_RISC ((uint)0x03 + CPM_IRQ_OFFSET)
-#define SIU_INT_SMC1 ((uint)0x04 + CPM_IRQ_OFFSET)
-#define SIU_INT_SMC2 ((uint)0x05 + CPM_IRQ_OFFSET)
-#define SIU_INT_IDMA1 ((uint)0x06 + CPM_IRQ_OFFSET)
-#define SIU_INT_IDMA2 ((uint)0x07 + CPM_IRQ_OFFSET)
-#define SIU_INT_IDMA3 ((uint)0x08 + CPM_IRQ_OFFSET)
-#define SIU_INT_IDMA4 ((uint)0x09 + CPM_IRQ_OFFSET)
-#define SIU_INT_SDMA ((uint)0x0a + CPM_IRQ_OFFSET)
-#define SIU_INT_USB ((uint)0x0b + CPM_IRQ_OFFSET)
-#define SIU_INT_TIMER1 ((uint)0x0c + CPM_IRQ_OFFSET)
-#define SIU_INT_TIMER2 ((uint)0x0d + CPM_IRQ_OFFSET)
-#define SIU_INT_TIMER3 ((uint)0x0e + CPM_IRQ_OFFSET)
-#define SIU_INT_TIMER4 ((uint)0x0f + CPM_IRQ_OFFSET)
-#define SIU_INT_TMCNT ((uint)0x10 + CPM_IRQ_OFFSET)
-#define SIU_INT_PIT ((uint)0x11 + CPM_IRQ_OFFSET)
-#define SIU_INT_PCI ((uint)0x12 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ1 ((uint)0x13 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ2 ((uint)0x14 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ3 ((uint)0x15 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ4 ((uint)0x16 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ5 ((uint)0x17 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ6 ((uint)0x18 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ7 ((uint)0x19 + CPM_IRQ_OFFSET)
-#define SIU_INT_FCC1 ((uint)0x20 + CPM_IRQ_OFFSET)
-#define SIU_INT_FCC2 ((uint)0x21 + CPM_IRQ_OFFSET)
-#define SIU_INT_FCC3 ((uint)0x22 + CPM_IRQ_OFFSET)
-#define SIU_INT_MCC1 ((uint)0x24 + CPM_IRQ_OFFSET)
-#define SIU_INT_MCC2 ((uint)0x25 + CPM_IRQ_OFFSET)
-#define SIU_INT_SCC1 ((uint)0x28 + CPM_IRQ_OFFSET)
-#define SIU_INT_SCC2 ((uint)0x29 + CPM_IRQ_OFFSET)
-#define SIU_INT_SCC3 ((uint)0x2a + CPM_IRQ_OFFSET)
-#define SIU_INT_SCC4 ((uint)0x2b + CPM_IRQ_OFFSET)
-#define SIU_INT_PC15 ((uint)0x30 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC14 ((uint)0x31 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC13 ((uint)0x32 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC12 ((uint)0x33 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC11 ((uint)0x34 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC10 ((uint)0x35 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC9 ((uint)0x36 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC8 ((uint)0x37 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC7 ((uint)0x38 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC6 ((uint)0x39 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC5 ((uint)0x3a + CPM_IRQ_OFFSET)
-#define SIU_INT_PC4 ((uint)0x3b + CPM_IRQ_OFFSET)
-#define SIU_INT_PC3 ((uint)0x3c + CPM_IRQ_OFFSET)
-#define SIU_INT_PC2 ((uint)0x3d + CPM_IRQ_OFFSET)
-#define SIU_INT_PC1 ((uint)0x3e + CPM_IRQ_OFFSET)
-#define SIU_INT_PC0 ((uint)0x3f + CPM_IRQ_OFFSET)
-
-#endif /* CONFIG_8260 */
-
-#endif /* Whatever way too big #ifdef */
-
-#define NR_MASK_WORDS ((NR_IRQS + 31) / 32)
-/* pedantic: these are long because they are used with set_bit --RR */
-extern unsigned long ppc_cached_irq_mask[NR_MASK_WORDS];
-
-/*
- * Because many systems have two overlapping names spaces for
- * interrupts (ISA and XICS for example), and the ISA interrupts
- * have historically not been easy to renumber, we allow ISA
- * interrupts to take values 0 - 15, and shift up the remaining
- * interrupts by 0x10.
- */
-#define NUM_ISA_INTERRUPTS 0x10
-extern int __irq_offset_value;
-
-static inline int irq_offset_up(int irq)
-{
- return(irq + __irq_offset_value);
-}
-
-static inline int irq_offset_down(int irq)
-{
- return(irq - __irq_offset_value);
-}
-
-static inline int irq_offset_value(void)
-{
- return __irq_offset_value;
-}
-
-#ifdef __DO_IRQ_CANON
-extern int ppc_do_canonicalize_irqs;
-#else
-#define ppc_do_canonicalize_irqs 0
-#endif
-
-static __inline__ int irq_canonicalize(int irq)
-{
- if (ppc_do_canonicalize_irqs && irq == 2)
- irq = 9;
- return irq;
-}
-#endif /* CONFIG_PPC_MERGE */
-
extern int distribute_irqs;
struct irqaction;
EXPORT_SYMBOL(__irq_offset_value);
atomic_t ppc_n_lost_interrupts;
-#ifndef CONFIG_PPC_MERGE
-#define NR_MASK_WORDS ((NR_IRQS + 31) / 32)
-unsigned long ppc_cached_irq_mask[NR_MASK_WORDS];
-#endif
-
#ifdef CONFIG_TAU_INT
extern int tau_initialized;
extern int tau_interrupts(int);
#endif
#endif /* CONFIG_PPC32 */
-#if defined(CONFIG_SMP) && !defined(CONFIG_PPC_MERGE)
-extern atomic_t ipi_recv;
-extern atomic_t ipi_sent;
-#endif
-
#ifdef CONFIG_PPC64
EXPORT_SYMBOL(irq_desc);
skip:
spin_unlock_irqrestore(&desc->lock, flags);
} else if (i == NR_IRQS) {
-#ifdef CONFIG_PPC32
-#ifdef CONFIG_TAU_INT
+#if defined(CONFIG_PPC32) && defined(CONFIG_TAU_INT)
if (tau_initialized){
seq_puts(p, "TAU: ");
for_each_online_cpu(j)
seq_printf(p, "%10u ", tau_interrupts(j));
seq_puts(p, " PowerPC Thermal Assist (cpu temp)\n");
}
-#endif
-#if defined(CONFIG_SMP) && !defined(CONFIG_PPC_MERGE)
- /* should this be per processor send/receive? */
- seq_printf(p, "IPI (recv/sent): %10u/%u\n",
- atomic_read(&ipi_recv), atomic_read(&ipi_sent));
-#endif
-#endif /* CONFIG_PPC32 */
+#endif /* CONFIG_PPC32 && CONFIG_TAU_INT*/
seq_printf(p, "BAD: %10u\n", ppc_spurious_interrupts);
}
return 0;
* IRQ controller and virtual interrupts
*/
-#ifdef CONFIG_PPC_MERGE
-
static LIST_HEAD(irq_hosts);
static DEFINE_SPINLOCK(irq_big_lock);
static DEFINE_PER_CPU(unsigned int, irq_radix_reader);
__initcall(irq_debugfs_init);
#endif /* CONFIG_VIRQ_DEBUG */
-#endif /* CONFIG_PPC_MERGE */
-
#ifdef CONFIG_PPC64
static int __init setup_noirqdistrib(char *str)
{
projects / openwrt / staging / blogic.git / commitdiff