ipq806x: enable GMAC support in DTS

This adds the GMAC entries in the ipq806x dtsi file as well as in the
ap148 specific dts file.

This also adds the MDIO change as well.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44520

diff --git a/target/linux/ipq806x/patches/700-add-gmac-dts-suport.patch b/target/linux/ipq806x/patches/700-add-gmac-dts-suport.patch
new file mode 100644 (file)
index 0000000..89ebe66
--- /dev/null
+++ b/target/linux/ipq806x/patches/700-add-gmac-dts-suport.patch
@@ -0,0 +1,172 @@
+--- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
++++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+@@ -18,8 +18,15 @@
+               bootargs = "console=ttyMSM0,115200 root=/dev/mtdblock12 rootfstype=squashfs,jffs2";
+       };
+ 
++      aliases {
++              mdio-gpio0 = &mdio0;
++      };
++
+       soc {
+               pinmux@800000 {
++                      pinctrl-0 = <&mdio0_pins &rgmii2_pins>;
++                      pinctrl-names = "default";
++
+                       i2c4_pins: i2c4_pinmux {
+                               pins = "gpio12", "gpio13";
+                               function = "gsbi4";
+@@ -34,6 +41,25 @@
+                                       bias-none;
+                               };
+                       };
++
++                      mdio0_pins: mdio0_pins {
++                              mux {
++                                      pins = "gpio0", "gpio1";
++                                      function = "gpio";
++                                      drive-strength = <8>;
++                                      bias-disable;
++                              };
++                      };
++
++                      rgmii2_pins: rgmii2_pins {
++                              mux {
++                                      pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
++                                             "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
++                                      function = "rgmii2";
++                                      drive-strength = <8>;
++                                      bias-disable;
++                              };
++                      };
+               };
+ 
+               gsbi@16300000 {
+@@ -72,6 +98,7 @@
+                                       #size-cells = <1>;
+                                       spi-max-frequency = <50000000>;
+                                       reg = <0>;
++                                      m25p,fast-read;
+ 
+                                       partition@0 {
+                                               label = "0:SBL1";
+@@ -148,5 +175,66 @@
+               sata@29000000 {
+                       status = "ok";
+               };
++
++              mdio0: mdio {
++                      compatible = "virtual,mdio-gpio";
++                      #address-cells = <1>;
++                      #size-cells = <0>;
++                      gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
++
++                      phy0: ethernet-phy@0 {
++                              device_type = "ethernet-phy";
++                              reg = <0>;
++                              qca,ar8327-initvals = <
++                                      0x00004 0x7600000   /* PAD0_MODE */
++                                      0x00008 0x1000000   /* PAD5_MODE */
++                                      0x0000c 0x80        /* PAD6_MODE */
++                                      0x000e4 0xaa545     /* MAC_POWER_SEL */
++                                      0x000e0 0xc74164de  /* SGMII_CTRL */
++                                      0x0007c 0x4e        /* PORT0_STATUS */
++                                      0x00094 0x4e        /* PORT6_STATUS */
++                              >;
++                      };
++
++                      phy4: ethernet-phy@4 {
++                              device_type = "ethernet-phy";
++                              reg = <4>;
++                      };
++              };
++
++              nss-gmac-common {
++                      reg = <0x03000000 0x0000FFFF 0x1bb00000 0x0000FFFF 0x00900000 0x00004000>;
++                      reg-names = "nss_reg_base" , "qsgmii_reg_base", "clk_ctl_base";
++              };
++
++              gmac1: ethernet@37200000 {
++                      status = "ok";
++                      phy-mode = "rgmii";
++                      qcom,id = <1>;
++                      qcom,phy_mdio_addr = <4>;
++                      qcom,poll_required = <1>;
++                      qcom,rgmii_delay = <0>;
++                      qcom,emulation = <0>;
++                      qcom,forced_speed = <1000>;
++                      qcom,forced_duplex = <1>;
++                      qcom,socver = <0>;
++                      local-mac-address = [000000000000];
++                      mdiobus = <&mdio0>;
++              };
++
++              gmac2: ethernet@37400000 {
++                      status = "ok";
++                      phy-mode = "sgmii";
++                      qcom,id = <2>;
++                      qcom,phy_mdio_addr = <0>;
++                      qcom,poll_required = <0>;
++                      qcom,rgmii_delay = <0>;
++                      qcom,emulation = <0>;
++                      qcom,forced_speed = <1000>;
++                      qcom,forced_duplex = <1>;
++                      qcom,socver = <0>;
++                      local-mac-address = [000000000000];
++                      mdiobus = <&mdio0>;
++              };
+       };
+ };
+--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
+@@ -3,6 +3,7 @@
+ #include "skeleton.dtsi"
+ #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
+ #include <dt-bindings/soc/qcom,gsbi.h>
++#include <dt-bindings/interrupt-controller/arm-gic.h>
+ 
+ / {
+       model = "Qualcomm IPQ8064";
+@@ -279,5 +280,42 @@
+                       #clock-cells = <1>;
+                       #reset-cells = <1>;
+               };
++
++              nss-gmac-common {
++                      reg = <0x03000000 0x0000FFFF 0x1bb00000 0x0000FFFF 0x00900000 0x00004000>;
++                      reg-names = "nss_reg_base" , "qsgmii_reg_base", "clk_ctl_base";
++              };
++
++              gmac0: ethernet@37000000 {
++                      device_type = "network";
++                      compatible = "qcom,nss-gmac";
++                      reg = <0x37000000 0x200000>;
++                      interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
++                      status = "disabled";
++              };
++
++              gmac1: ethernet@37200000 {
++                      device_type = "network";
++                      compatible = "qcom,nss-gmac";
++                      reg = <0x37200000 0x200000>;
++                      interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
++                      status = "disabled";
++              };
++
++              gmac2: ethernet@37400000 {
++                      device_type = "network";
++                      compatible = "qcom,nss-gmac";
++                      reg = <0x37400000 0x200000>;
++                      interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
++                      status = "disabled";
++              };
++
++              gmac3: ethernet@37600000 {
++                      device_type = "network";
++                      compatible = "qcom,nss-gmac";
++                      reg = <0x37600000 0x200000>;
++                      interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
++                      status = "disabled";
++              };
+       };
+ };