ath79: Add support for OpenMesh OM5P-AC v1

Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8035 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>

diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index 2ad15a7a40825956c017e20ecbdf6291f8e60a84..b01a713705027100f5b13e6b75c7974af87f843c 100644 (file)
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -58,6 +58,7 @@ openmesh,mr1750-v1|\
 openmesh,mr1750-v2|\
 openmesh,om5p|\
 openmesh,om5p-an|\
+openmesh,om5p-ac-v1|\
 openmesh,om5p-ac-v2|\
 samsung,wam250|\
 ubnt,nanostation-m|\

diff --git a/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts
new file mode 100644 (file)
index 0000000..de21f01
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts
@@ -0,0 +1,216 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "openmesh,om5p-ac-v1", "qca,qca9558";
+       model = "OpenMesh OM5P-AC v1";
+
+       chosen {
+               /delete-property/ bootargs;
+       };
+
+       aliases {
+               serial0 = &uart;
+               led-boot = &led_power_blue;
+               led-failsafe = &led_power_blue;
+               led-running = &led_power_blue;
+               led-upgrade = &led_power_blue;
+               label-mac-device = &eth0;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_power_blue: power_blue {
+                       label = "blue:power";
+                       gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+                       default-state = "on";
+               };
+
+               wan_blue {
+                       label = "blue:wan";
+                       gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+               };
+
+               lan_blue {
+                       label = "blue:lan";
+                       gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+               };
+
+               wifi_green {
+                       label = "green:wifi";
+                       gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+
+               wifi_yellow {
+                       label = "yellow:wifi";
+                       gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+               };
+
+               wifi_red {
+                       label = "red:wifi";
+                       gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       i2c {
+               compatible = "i2c-gpio";
+               gpios = <&gpio 11 GPIO_ACTIVE_HIGH /* sda */
+                        &gpio 12 GPIO_ACTIVE_HIGH /* scl */
+                       >;
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               i2c-gpio,scl-open-drain;
+               i2c-gpio,sda-open-drain;
+
+               tmp423a@4c {
+                       compatible = "ti,tmp423";
+                       reg = <0x4c>;
+               };
+       };
+
+       watchdog {
+               compatible = "linux,wdt-gpio";
+               gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+               hw_algo = "toggle";
+               /* hw_margin_ms is actually 300s but driver limits it to 60s */
+               hw_margin_ms = <60000>;
+               always-running;
+       };
+};
+
+&spi {
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <40000000>;
+
+               /* partitions are passed via bootloader */
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x000000 0x040000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "u-boot-env";
+                               reg = <0x040000 0x010000>;
+                       };
+
+                       partition@50000 {
+                               label = "custom";
+                               reg = <0x050000 0x060000>;
+                               read-only;
+                       };
+
+                       partition@b0000 {
+                               label = "inactive";
+                               reg = <0x0b0000 0x7a0000>;
+                       };
+
+                       partition@850000 {
+                               label = "inactive2";
+                               reg = <0x850000 0x7a0000>;
+                       };
+
+                       art: partition@ff0000 {
+                               label = "ART";
+                               reg = <0xff0000 0x010000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&mdio0 {
+       status = "okay";
+
+       phy-mask = <0x6>;
+
+       phy1: ethernet-phy@1 {
+               reg = <1>;
+               eee-broken-100tx;
+               eee-broken-1000t;
+       };
+
+       phy2: ethernet-phy@2 {
+               reg = <2>;
+               eee-broken-100tx;
+               eee-broken-1000t;
+               at803x-override-sgmii-link-check;
+       };
+};
+
+&eth0 {
+       status = "okay";
+
+       pll-data = <0x82000101 0x80000101 0x80001313>;
+
+       nvmem-cells = <&macaddr_art_0>;
+       nvmem-cell-names = "mac-address";
+
+       phy-mode = "rgmii-id";
+       phy-handle = <&phy1>;
+
+       gmac-config {
+               device = <&gmac>;
+               rgmii-enabled = <1>;
+               rxd-delay = <3>;
+               rxdv-delay = <3>;
+               txd-delay = <0>;
+               txen-delay = <0>;
+       };
+};
+
+&eth1 {
+       status = "okay";
+
+       pll-data = <0x03000101 0x80000101 0x80001313>;
+
+       nvmem-cells = <&macaddr_art_6>;
+       nvmem-cell-names = "mac-address";
+
+       qca955x-sgmii-fixup;
+
+       phy-handle = <&phy2>;
+};
+
+&wmac {
+       status = "okay";
+
+       mtd-cal-data = <&art 0x1000>;
+       nvmem-cells = <&macaddr_art_0>;
+       nvmem-cell-names = "mac-address";
+       mac-address-increment = <2>;
+};
+
+&pcie1 {
+       status = "okay";
+};
+
+&art {
+       compatible = "nvmem-cells";
+       #address-cells = <1>;
+       #size-cells = <1>;
+
+       macaddr_art_0: macaddr@0 {
+               reg = <0x0 0x6>;
+       };
+
+       macaddr_art_6: macaddr@6 {
+               reg = <0x6 0x6>;
+       };
+};

diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 14b38b4e66af1c0d700536383857cd2f8dc0ce2d..652b54092e02025d8f686756f423ccc0b250000b 100644 (file)
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -271,6 +271,10 @@ openmesh,om2p-hs-v4)
        ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0"
        ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02"
        ;;
+openmesh,om5p-ac-v1)
+       ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0"
+       ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
+       ;;
 openmesh,om5p-an)
        ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0"
        ucidef_set_led_switch "wan" "WAN" "blue:wan" "switch0" "0x02"

diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index ef9b8dee910d15d31c3081a481abeabcbb89d0e4..c0e5078bdb2e0c1d2d79985244398be7b9501abf 100644 (file)
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -165,6 +165,10 @@ case "$FIRMWARE" in
        ;;
 "ath10k/cal-pci-0000:01:00.0.bin")
        case $board in
+       openmesh,om5p-ac-v1)
+               caldata_extract "ART" 0x5000 0x844
+               ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
+               ;;
        sitecom,wlr-8100)
                caldata_extract "art" 0x5000 0x844
                ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 1)

diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
index b7e2930129d78e9309ede6ebd8d73b1a9fb3926c..3d953d7982d17c12c5d840c476b6839513bf818c 100644 (file)
--- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
@@ -81,6 +81,7 @@ platform_do_upgrade() {
        openmesh,om2p-hs-v4|\
        openmesh,om2p-lc|\
        openmesh,om5p|\
+       openmesh,om5p-ac-v1|\
        openmesh,om5p-an)
                PART_NAME="inactive"
                platform_do_upgrade_openmesh "$1"

diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index e17b498d883d660d0126e5f556f1dd2d67aef4a9..8e97fec402ab975b57f23f0d2d4f276841941c86 100644 (file)
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1913,6 +1913,17 @@ define Device/openmesh_om5p
 endef
 TARGET_DEVICES += openmesh_om5p
 
+define Device/openmesh_om5p-ac-v1
+  $(Device/openmesh_common_64k)
+  SOC := qca9558
+  DEVICE_MODEL := OM5P-AC
+  DEVICE_VARIANT := v1
+  DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
+  OPENMESH_CE_TYPE := OM5PAC
+  SUPPORTED_DEVICES += om5p-ac
+endef
+TARGET_DEVICES += openmesh_om5p-ac-v1
+
 define Device/openmesh_om5p-ac-v2
   SOC := qca9558
   DEVICE_VENDOR := OpenMesh