rv1108-evb.dtb
dtb-$(CONFIG_ARCH_MESON) += \
meson-gxbb-odroidc2.dtb \
- meson-gxl-s905x-p212.dtb
+ meson-gxl-s905x-p212.dtb \
+ meson-gxl-s905x-libretech-cc.dtb
dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
tegra20-medcom-wide.dtb \
tegra20-paz00.dtb \
--- /dev/null
+/*
+ * Copyright (c) 2017 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+#include "meson-gxl-s905x.dtsi"
+
+/ {
+ compatible = "libretech,cc", "amlogic,s905x", "amlogic,meson-gxl";
+ model = "Libre Technology CC";
+
+ aliases {
+ serial0 = &uart_AO;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ system {
+ label = "librecomputer:system-status";
+ gpios = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ panic-indicator;
+ };
+
+ blue {
+ label = "librecomputer:blue";
+ gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_card: regulator-vcc-card {
+ compatible = "regulator-gpio";
+
+ regulator-name = "VCC_CARD";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0>,
+ <1800000 1>;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
+
+ðmac {
+ status = "okay";
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+ pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_card>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <50000000>;
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
with 2 GiB of RAM, Ethernet, HDMI, 2 USB, micro-SD slot,
eMMC, IR receiver, CVBS+Audio jack and a SDIO WiFi module.
+config TARGET_LIBRETECH_CC
+ bool "LIBRETECH-CC"
+ help
+ LibreTech CC is a single board computer based on Meson GXL
+ with 2 GiB of RAM, Ethernet, HDMI, 4 USB, micro-SD slot,
+ eMMC, IR receiver and a 40-pin GPIO header.
+
endif
config SYS_SOC
source "board/amlogic/p212/Kconfig"
+source "board/amlogic/libretech-cc/Kconfig"
+
endif
--- /dev/null
+if TARGET_LIBRETECH_CC
+
+config SYS_BOARD
+ default "libretech-cc"
+
+config SYS_VENDOR
+ default "amlogic"
+
+config SYS_CONFIG_NAME
+ default "libretech-cc"
+
+endif
--- /dev/null
+LIBRETECH-CC
+M: Neil Armstrong <narmstrong@baylibre.com>
+S: Maintained
+F: board/amlogic/libretech-cc/
+F: include/configs/libretech-cc.h
+F: configs/libretech-cc_defconfig
--- /dev/null
+#
+# (C) Copyright 2016 BayLibre, SAS
+# Author: Neil Armstrong <narmstrong@baylibre.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := libretech-cc.o
--- /dev/null
+U-Boot for LibreTech CC
+=======================
+
+LibreTech CC is a single board computer manufactured by Libre Technology
+with the following specifications:
+
+ - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 2GHz
+ - ARM Mali 450 GPU
+ - 2GB DDR3 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 40-pin GPIO header
+ - 4 x USB 2.0 Host, 1 x USB OTG
+ - eMMC, microSD
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+Currently the U-Boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+
+U-Boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make libretech-cc_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b libretech-cc amlogic-u-boot
+ > cd amlogic-u-boot
+ > make libretech_cc_defconfig
+ > make
+ > export FIPDIR=$PWD/fip
+
+Go back to mainline U-Boot source tree then :
+ > mkdir fip
+
+ > cp $FIPDIR/gxl/bl2.bin fip/
+ > cp $FIPDIR/gxl/acs.bin fip/
+ > cp $FIPDIR/gxl/bl21.bin fip/
+ > cp $FIPDIR/gxl/bl30.bin fip/
+ > cp $FIPDIR/gxl/bl301.bin fip/
+ > cp $FIPDIR/gxl/bl31.img fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl30.bin \
+ fip/zero_tmp \
+ fip/bl30_zero.bin \
+ fip/bl301.bin \
+ fip/bl301_zero.bin \
+ fip/bl30_new.bin \
+ bl30
+
+ > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl2_acs.bin \
+ fip/zero_tmp \
+ fip/bl2_zero.bin \
+ fip/bl21.bin \
+ fip/bl21_zero.bin \
+ fip/bl2_new.bin \
+ bl2
+
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
+ > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \
+ --output fip/u-boot.bin \
+ --bl2 fip/bl2.n.bin.sig \
+ --bl30 fip/bl30_new.bin.enc \
+ --bl31 fip/bl31.img.enc \
+ --bl33 fip/bl33.bin.enc
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
--- /dev/null
+/*
+ * Copyright (C) 2016 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <asm/io.h>
+#include <asm/arch/gxbb.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+
+#define EFUSE_SN_OFFSET 20
+#define EFUSE_SN_SIZE 16
+#define EFUSE_MAC_OFFSET 52
+#define EFUSE_MAC_SIZE 6
+
+int board_init(void)
+{
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ u8 mac_addr[EFUSE_MAC_SIZE];
+ char serial[EFUSE_SN_SIZE];
+ ssize_t len;
+
+ meson_gx_eth_init(PHY_INTERFACE_MODE_RMII,
+ MESON_GXL_USE_INTERNAL_RMII_PHY);
+
+ /* Enable power and clock gate */
+ setbits_le32(GXBB_GCLK_MPEG_1, GXBB_GCLK_MPEG_1_ETH);
+ clrbits_le32(GXBB_MEM_PD_REG_0, GXBB_MEM_PD_REG_0_ETH_MASK);
+
+ if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+ len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+ mac_addr, EFUSE_MAC_SIZE);
+ if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr))
+ eth_env_set_enetaddr("ethaddr", mac_addr);
+ }
+
+ if (!env_get("serial#")) {
+ len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+ EFUSE_SN_SIZE);
+ if (len == EFUSE_SN_SIZE)
+ env_set("serial#", serial);
+ }
+
+ return 0;
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MESON=y
+CONFIG_MESON_GXL=y
+CONFIG_TARGET_LIBRETECH_CC=y
+CONFIG_IDENT_STRING=" libretech-cc"
+CONFIG_DEFAULT_DEVICE_TREE="meson-gxl-s905x-libretech-cc"
+CONFIG_DEBUG_UART=y
+CONFIG_ENV_IS_NOWHERE=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_OF_CONTROL=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_PHY_MESON_GXL=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_GXL=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_BASE=0xc81004c0
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_OF_LIBFDT_OVERLAY=y
--- /dev/null
+/*
+ * Configuration for LibreTech CC
+ *
+ * Copyright (C) 2017 Baylibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_PHY_ADDR 8
+
+#define MESON_FDTFILE_SETTING "fdtfile=amlogic/meson-gxl-s905x-libretech-cc.dtb\0"
+
+#include <configs/meson-gxbb-common.h>
+
+#endif /* __CONFIG_H */
projects / project / bcm63xx / u-boot.git / commitdiff