board=$(board_name)
case "$board" in
+aerohive,br200-wp)
+ ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
+ ;;
aerohive,hiveap-330|\
enterasys,ws-ap3715i)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
CONFIG_BLK_MQ_PCI=y
CONFIG_BOOKE=y
CONFIG_BOOKE_WDT=y
+# CONFIG_BR200_WP is not set
# CONFIG_BSC9131_RDB is not set
# CONFIG_BSC9132_QDS is not set
# CONFIG_C293_PCIE is not set
CONFIG_EDAC_LEGACY_SYSFS=y
CONFIG_EDAC_MPC85XX=y
CONFIG_EDAC_SUPPORT=y
+# CONFIG_FIREBOX_T10 is not set
CONFIG_FIXED_PHY=y
CONFIG_FSL_BOOKE=y
# CONFIG_FSL_DPAA2_SWITCH is not set
# CONFIG_XES_MPC85xx is not set
CONFIG_XZ_DEC_BCJ=y
CONFIG_XZ_DEC_POWERPC=y
-# CONFIG_FIREBOX_T10 is not set
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Aerohive BR200-WP Device Tree Source
+ *
+ * Based on: Aerohive HiveAP-330 Device Tree Source
+ *
+ * Copyright (C) 2017 Chris Blake <chrisrblake93@gmail.com>
+ * Copyright (C) 2023 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/include/ "fsl/p1020si-pre.dtsi"
+
+/ {
+ model = "Aerohive BR200-WP";
+ compatible = "aerohive,br200-wp";
+
+ chosen {
+ bootargs = "console=ttyS0,9600";
+ bootargs-override = "console=ttyS0,9600 noinitrd";
+ };
+
+ aliases {
+ led-boot = &led_attention;
+ led-failsafe = &led_attention;
+ led-running = &led_status;
+ led-upgrade = &led_status;
+ label-mac-device = &enet0;
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ cpus {
+ /delete-property/ PowerPC,P1020@1; /* P1011 have one core only */
+ };
+
+ board_lbc: lbc: localbus@ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
+ ranges = <0x0 0x0 0x0 0xec000000 0x4000000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x4000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ reg = <0x0 0x40000>;
+ label = "dtb";
+ };
+
+ partition@40000 {
+ reg = <0x40000 0x40000>;
+ label = "initramfs";
+ };
+
+ partition@80000 {
+ reg = <0x80000 0x27c0000>;
+ label = "rootfs";
+ };
+
+ partition@2840000 {
+ reg = <0x2840000 0x800000>;
+ label = "kernel";
+ };
+
+ partition@3040000 {
+ reg = <0x3040000 0xec0000>;
+ label = "stock-jffs2";
+ read-only;
+ };
+
+ partition@3f00000 {
+ reg = <0x3f00000 0x20000>;
+ label = "hw-info";
+ read-only;
+
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_hwinfo_0: macaddr@0 {
+ reg = <0x0 0x6>;
+ };
+ };
+
+ partition@3f20000 {
+ reg = <0x3f20000 0x20000>;
+ label = "boot-info";
+ read-only;
+ };
+
+ partition@3f40000 {
+ reg = <0x3f40000 0x20000>;
+ label = "boot-info-backup";
+ read-only;
+ };
+
+ partition@3f60000 {
+ reg = <0x3f60000 0x20000>;
+ label = "u-boot-env";
+ };
+
+ partition@3f80000 {
+ reg = <0x3f80000 0x80000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ firmware@0 {
+ reg = <0x0 0x3040000>;
+ label = "firmware";
+ };
+ };
+ };
+ };
+
+ board_soc: soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+
+ mdio@24000 {
+
+ phy_port1: phy@0 {
+ reg = <0>;
+ };
+
+ phy_port2: phy@1 {
+ reg = <1>;
+ };
+
+ phy_port3: phy@2 {
+ reg = <2>;
+ };
+
+ phy_port4: phy@3 {
+ reg = <3>;
+ };
+
+ phy_port5: phy@4 {
+ reg = <4>;
+ };
+
+ switch@10 {
+ compatible = "qca,qca8327";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10>;
+ reset-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&phy_port1>;
+ nvmem-cells = <&macaddr_hwinfo_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <2>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&phy_port2>;
+ nvmem-cells = <&macaddr_hwinfo_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <3>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-handle = <&phy_port3>;
+ nvmem-cells = <&macaddr_hwinfo_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <4>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ phy-handle = <&phy_port4>;
+ nvmem-cells = <&macaddr_hwinfo_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <5>;
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "wan";
+ phy-handle = <&phy_port5>;
+ nvmem-cells = <&macaddr_hwinfo_0>;
+ nvmem-cell-names = "mac-address";
+ };
+
+ port@6 {
+ reg = <6>;
+ ethernet = <&enet0>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+
+ mdio@25000 {
+ status = "disabled";
+ };
+
+ mdio@26000 {
+ status = "disabled";
+ };
+
+ enet0: ethernet@b0000 {
+ status = "okay";
+ phy-connection-type = "rgmii-id";
+ nvmem-cells = <&macaddr_hwinfo_0>;
+ nvmem-cell-names = "mac-address";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ enet1: ethernet@b1000 {
+ status = "disabled";
+ };
+
+ enet2: ethernet@b2000 {
+ status = "disabled";
+ };
+
+ gpio0: gpio-controller@fc00 {
+ };
+
+ usb@22000 {
+ phy_type = "ulpi";
+ dr_mode = "host";
+ };
+
+ usb@23000 {
+ status = "disabled";
+ };
+ };
+
+ pci0: pcie@ffe09000 {
+ status = "disabled";
+ };
+
+ pci1: pcie@ffe0a000 {
+ reg = <0x0 0xffe0a000 0x0 0x1000>;
+ ranges = <0x2000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0x0 0xffc20000 0x0 0x10000>;
+
+ reset-gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xc0000000
+ 0x2000000 0x0 0xc0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+
+ ath9k: wifi@0,0 {
+ reg = <0x0000 0 0 0 0>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ nvmem-cells = <&macaddr_hwinfo_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <16>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_attention: led-0 {
+ gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+ label = "amber:status";
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_STATUS;
+ };
+
+ led_status: led-1 {
+ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+ label = "white:status";
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_STATUS;
+ };
+ };
+
+ buttons {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+/include/ "fsl/p1020si-post.dtsi"
+
+/ {
+ chosen {
+ linux,stdout-path = "/soc@ffe00000/serial@4500";
+ };
+
+ cpus {
+ PowerPC,P1020@0 {
+ i-cache-sets = <0x80>;
+ i-cache-size = <0x8000>;
+ i-cache-block-size = <0x20>;
+ d-cache-sets = <0x80>;
+ d-cache-size = <0x8000>;
+ d-cache-block-size = <0x20>;
+ clock-frequency = <0x2756cd00>;
+ bus-frequency = <0x13ab6680>;
+ timebase-frequency = <0x2756cd0>;
+ };
+ };
+
+ memory {
+ reg = <0x00 0x00 0x00 0x10000000>;
+ };
+
+ localbus@ffe05000 {
+ bus-frequency = <0x13ab668>;
+ };
+
+ soc@ffe00000 {
+ bus-frequency = <0x13ab6680>;
+
+ serial@4500 {
+ clock-frequency = <0x13ab6680>;
+ };
+
+ serial@4600 {
+ clock-frequency = <0x13ab6680>;
+ };
+ };
+
+ pcie@ffe09000 {
+ clock-frequency = <0x1fca055>;
+ };
+
+ pcie@ffe0a000 {
+ clock-frequency = <0x1fca055>;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Aerohive BR200-WP Board Setup
+ * Copyright (C) 2023 Pawel Dembicki <paweldembicki@gmail.com>
+ *
+ * Based on:
+ * hiveap-330.c:
+ * Aerohive HiveAP-330 Board Setup
+ * Copyright (C) 2017 Chris Blake <chrisrblake93@gmail.com>
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <mm/mmu_decl.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+#include "smp.h"
+
+#include "mpc85xx.h"
+
+void __init br200_wp_pic_init(void)
+{
+ struct mpic *mpic;
+
+ mpic = mpic_alloc(NULL, 0,
+ MPIC_BIG_ENDIAN |
+ MPIC_SINGLE_DEST_CPU,
+ 0, 256, " OpenPIC ");
+
+ BUG_ON(mpic == NULL);
+ mpic_init(mpic);
+}
+
+/*
+ * Setup the architecture
+ */
+static void __init br200_wp_setup_arch(void)
+{
+ if (ppc_md.progress)
+ ppc_md.progress("br200_wp_setup_arch()", 0);
+
+ fsl_pci_assign_primary();
+
+ pr_info("br200-wp board from Aerohive\n");
+}
+
+machine_arch_initcall(br200_wp, mpc85xx_common_publish_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init br200_wp_probe(void)
+{
+ if (of_machine_is_compatible("aerohive,br200-wp"))
+ return 1;
+ return 0;
+}
+
+define_machine(br200_wp) {
+ .name = "P1020 RDB",
+ .probe = br200_wp_probe,
+ .setup_arch = br200_wp_setup_arch,
+ .init_IRQ = br200_wp_pic_init,
+#ifdef CONFIG_PCI
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
+ .pcibios_fixup_phb = fsl_pcibios_fixup_phb,
+#endif
+ .get_irq = mpic_get_irq,
+ .calibrate_decr = generic_calibrate_decr,
+ .progress = udbg_progress,
+};
mv "$@.new" "$@"
endef
+define Device/aerohive_br200-wp
+ DEVICE_VENDOR := Aerohive
+ DEVICE_MODEL := BR200-WP
+ BLOCKSIZE := 128k
+ KERNEL_NAME := simpleImage.br200-wp
+ KERNEL := kernel-bin | uImage none
+ KERNEL_INITRAMFS := kernel-bin | uImage none
+ KERNEL_ENTRY := 0x1000000
+ KERNEL_LOADADDR := 0x1000000
+ KERNEL_SIZE := 8m
+ IMAGES := fdt.bin sysupgrade.bin
+ IMAGE/fdt.bin := append-dtb
+ IMAGE/sysupgrade.bin := append-dtb | pad-to 256k | check-size 256k | \
+ append-uImage-fakehdr ramdisk | pad-to 256k | check-size 512k | \
+ append-rootfs | pad-rootfs $$(BLOCKSIZE) | pad-to 41216k | check-size 41216k | \
+ append-kernel | append-metadata
+ IMAGE_SIZE = 63m
+endef
+TARGET_DEVICES += aerohive_br200-wp
+
define Device/enterasys_ws-ap3715i
DEVICE_VENDOR := Enterasys
DEVICE_MODEL := WS-AP3715i
CONFIG_AT803X_PHY=y
+CONFIG_BR200_WP=y
CONFIG_CMDLINE_OVERRIDE=y
+CONFIG_FIREBOX_T10=y
# CONFIG_FSL_CORENET_CF is not set
CONFIG_GPIO_74X164=y
+CONFIG_MTD_CFI=y
CONFIG_MTD_NAND_FSL_IFC=y
+CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_SPLIT_FIRMWARE=y
CONFIG_MTD_SPLIT_TPLINK_FW=y
CONFIG_MTD_SPLIT_UIMAGE_FW=y
CONFIG_TL_WDR4900_V1=y
CONFIG_UBIFS_FS=y
CONFIG_WS_AP3715I=y
-CONFIG_FIREBOX_T10=y
\ No newline at end of file
BOARDNAME:=P1010
-KERNEL_IMAGES:=simpleImage.tl-wdr4900-v1 simpleImage.ws-ap3715i
+KERNEL_IMAGES:=simpleImage.br200-wp simpleImage.tl-wdr4900-v1 simpleImage.ws-ap3715i
define Target/Description
Build firmware images for P1010 based boards.
--- /dev/null
+--- a/arch/powerpc/platforms/85xx/Kconfig
++++ b/arch/powerpc/platforms/85xx/Kconfig
+@@ -49,6 +49,16 @@ config BSC9132_QDS
+ and dual StarCore SC3850 DSP cores.
+ Manufacturer : Freescale Semiconductor, Inc
+
++config BR200_WP
++ bool "Aerohive BR200-WP"
++ select DEFAULT_UIMAGE
++ select ARCH_REQUIRE_GPIOLIB
++ select GPIO_MPC8XXX
++ help
++ This option enables support for the Aerohive BR200-WP board.
++
++ This board is a wireless router with a Freescale P1011 SoC.
++
+ config HIVEAP_330
+ bool "Aerohive HiveAP-330"
+ select DEFAULT_UIMAGE
+--- a/arch/powerpc/platforms/85xx/Makefile
++++ b/arch/powerpc/platforms/85xx/Makefile
+@@ -12,6 +12,7 @@ obj-y += common.o
+ obj-$(CONFIG_BSC9131_RDB) += bsc913x_rdb.o
+ obj-$(CONFIG_BSC9132_QDS) += bsc913x_qds.o
+ obj-$(CONFIG_C293_PCIE) += c293pcie.o
++obj-$(CONFIG_BR200_WP) += br200-wp.o
+ obj-$(CONFIG_HIVEAP_330) += hiveap-330.o
+ obj-$(CONFIG_MPC8540_ADS) += mpc85xx_ads.o
+ obj-$(CONFIG_MPC8560_ADS) += mpc85xx_ads.o
+--- a/arch/powerpc/boot/Makefile
++++ b/arch/powerpc/boot/Makefile
+@@ -163,6 +163,7 @@ src-plat-$(CONFIG_PPC_PSERIES) += pserie
+ src-plat-$(CONFIG_PPC_POWERNV) += pseries-head.S
+ src-plat-$(CONFIG_PPC_IBM_CELL_BLADE) += pseries-head.S
+ src-plat-$(CONFIG_MVME7100) += motload-head.S mvme7100.c
++src-plat-$(CONFIG_BR200_WP) += simpleboot.c fixed-head.S
+ src-plat-$(CONFIG_TL_WDR4900_V1) += simpleboot.c fixed-head.S
+ src-plat-$(CONFIG_WS_AP3825I) += simpleboot.c fixed-head.S
+
+@@ -345,6 +346,7 @@ image-$(CONFIG_TQM8548) += cuImage.tqm
+ image-$(CONFIG_TQM8555) += cuImage.tqm8555
+ image-$(CONFIG_TQM8560) += cuImage.tqm8560
+ image-$(CONFIG_KSI8560) += cuImage.ksi8560
++image-$(CONFIG_BR200_WP) += simpleImage.br200-wp
+ image-$(CONFIG_TL_WDR4900_V1) += simpleImage.tl-wdr4900-v1
+ image-$(CONFIG_WS_AP3715I) += simpleImage.ws-ap3715i
+ image-$(CONFIG_WS_AP3825I) += simpleImage.ws-ap3825i
+--- a/arch/powerpc/boot/wrapper
++++ b/arch/powerpc/boot/wrapper
+@@ -326,6 +326,7 @@ adder875-redboot)
+ platformo="$object/fixed-head.o $object/redboot-8xx.o"
+ binary=y
+ ;;
++simpleboot-br200-wp|\
+ simpleboot-ws-ap3715i|\
+ simpleboot-ws-ap3825i|\
+ simpleboot-tl-wdr4900-v1)
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
-@@ -273,7 +273,6 @@ image-$(CONFIG_PPC_CHRP) += zImage.chrp
+@@ -274,7 +274,6 @@ image-$(CONFIG_PPC_CHRP) += zImage.chrp
image-$(CONFIG_PPC_EFIKA) += zImage.chrp
image-$(CONFIG_PPC_PMAC) += zImage.pmac
image-$(CONFIG_PPC_HOLLY) += dtbImage.holly
image-$(CONFIG_EPAPR_BOOT) += zImage.epapr
#
-@@ -407,15 +406,6 @@ $(obj)/dtbImage.%: vmlinux $(wrapperbits
+@@ -409,15 +408,6 @@ $(obj)/dtbImage.%: vmlinux $(wrapperbits
$(obj)/vmlinux.strip: vmlinux
$(STRIP) -s -R .comment $< -o $@
projects / openwrt / staging / jow.git / commitdiff