--- /dev/null
+--- a/arch/mips/Makefile
++++ b/arch/mips/Makefile
+@@ -637,6 +637,13 @@ else
+ load-$(CONFIG_CPU_CAVIUM_OCTEON) += 0xffffffff81100000
+ endif
+
++#
++# Atheros AR71xx
++#
++core-$(CONFIG_ATHEROS_AR71XX) += arch/mips/ar71xx/
++cflags-$(CONFIG_ATHEROS_AR71XX) += -I$(srctree)/arch/mips/include/asm/mach-ar71xx
++load-$(CONFIG_ATHEROS_AR71XX) += 0xffffffff80060000
++
+ # temporary until string.h is fixed
+ cflags-y += -ffreestanding
+
+--- a/arch/mips/Kconfig
++++ b/arch/mips/Kconfig
+@@ -48,6 +48,23 @@ config AR7
+ Support for the Texas Instruments AR7 System-on-a-Chip
+ family: TNETD7100, 7200 and 7300.
+
++config ATHEROS_AR71XX
++ bool "Atheros AR71xx based boards"
++ select CEVT_R4K
++ select CSRC_R4K
++ select DMA_NONCOHERENT
++ select HW_HAS_PCI
++ select IRQ_CPU
++ select ARCH_REQUIRE_GPIOLIB
++ select SYS_HAS_CPU_MIPS32_R1
++ select SYS_HAS_CPU_MIPS32_R2
++ select SYS_SUPPORTS_32BIT_KERNEL
++ select SYS_SUPPORTS_BIG_ENDIAN
++ select SYS_HAS_EARLY_PRINTK
++ select MIPS_MACHINE
++ help
++ Support for Atheros AR71xx based boards.
++
+ config BCM47XX
+ bool "BCM47XX based boards"
+ select CEVT_R4K
+@@ -682,6 +699,7 @@ config CAVIUM_OCTEON_REFERENCE_BOARD
+ endchoice
+
+ source "arch/mips/alchemy/Kconfig"
++source "arch/mips/ar71xx/Kconfig"
+ source "arch/mips/bcm63xx/Kconfig"
+ source "arch/mips/jazz/Kconfig"
+ source "arch/mips/lasat/Kconfig"
--- /dev/null
+--- a/arch/mips/pci/Makefile
++++ b/arch/mips/pci/Makefile
+@@ -18,6 +18,7 @@ obj-$(CONFIG_PCI_TX4927) += ops-tx4927.o
+ obj-$(CONFIG_BCM47XX) += pci-bcm47xx.o
+ obj-$(CONFIG_BCM63XX) += pci-bcm63xx.o fixup-bcm63xx.o \
+ ops-bcm63xx.o
++obj-$(CONFIG_ATHEROS_AR71XX) += pci-ar71xx.o pci-ar724x.o
+
+ #
+ # These are still pretty much in the old state, watch, go blind.
--- /dev/null
+--- a/drivers/usb/host/Kconfig
++++ b/drivers/usb/host/Kconfig
+@@ -109,6 +109,13 @@ config XPS_USB_HCD_XILINX
+ support both high speed and full speed devices, or high speed
+ devices only.
+
++config USB_EHCI_AR71XX
++ bool "USB EHCI support for AR71xx"
++ depends on USB_EHCI_HCD && ATHEROS_AR71XX
++ default y
++ help
++ Support for Atheros AR71xx built-in EHCI controller
++
+ config USB_EHCI_FSL
+ bool "Support for Freescale on-chip EHCI USB controller"
+ depends on USB_EHCI_HCD && FSL_SOC
+@@ -207,6 +214,13 @@ config USB_OHCI_HCD
+ To compile this driver as a module, choose M here: the
+ module will be called ohci-hcd.
+
++config USB_OHCI_AR71XX
++ bool "USB OHCI support for Atheros AR71xx"
++ depends on USB_OHCI_HCD && ATHEROS_AR71XX
++ default y
++ help
++ Support for Atheros AR71xx built-in OHCI controller
++
+ config USB_OHCI_HCD_PPC_SOC
+ bool "OHCI support for on-chip PPC USB controller"
+ depends on USB_OHCI_HCD && (STB03xxx || PPC_MPC52xx)
+--- a/drivers/usb/host/ehci-hcd.c
++++ b/drivers/usb/host/ehci-hcd.c
+@@ -1158,6 +1158,11 @@ MODULE_LICENSE ("GPL");
+ #define PLATFORM_DRIVER ehci_atmel_driver
+ #endif
+
++#ifdef CONFIG_USB_EHCI_AR71XX
++#include "ehci-ar71xx.c"
++#define PLATFORM_DRIVER ehci_ar71xx_driver
++#endif
++
+ #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
+ !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER)
+ #error "missing bus glue for ehci-hcd"
+--- a/drivers/usb/host/ohci-hcd.c
++++ b/drivers/usb/host/ohci-hcd.c
+@@ -1085,6 +1085,11 @@ MODULE_LICENSE ("GPL");
+ #define TMIO_OHCI_DRIVER ohci_hcd_tmio_driver
+ #endif
+
++#ifdef CONFIG_USB_OHCI_AR71XX
++#include "ohci-ar71xx.c"
++#define PLATFORM_DRIVER ohci_hcd_ar71xx_driver
++#endif
++
+ #if !defined(PCI_DRIVER) && \
+ !defined(PLATFORM_DRIVER) && \
+ !defined(OF_PLATFORM_DRIVER) && \
--- /dev/null
+--- a/drivers/spi/Kconfig
++++ b/drivers/spi/Kconfig
+@@ -53,6 +53,13 @@ if SPI_MASTER
+
+ comment "SPI Master Controller Drivers"
+
++config SPI_AR71XX
++ tristate "Atheros AR71xx SPI Controller"
++ depends on SPI_MASTER && ATHEROS_AR71XX
++ select SPI_BITBANG
++ help
++ This is the SPI contoller driver for Atheros AR71xx.
++
+ config SPI_ATMEL
+ tristate "Atmel SPI Controller"
+ depends on (ARCH_AT91 || AVR32)
+--- a/drivers/spi/Makefile
++++ b/drivers/spi/Makefile
+@@ -11,6 +11,7 @@ endif
+ obj-$(CONFIG_SPI_MASTER) += spi.o
+
+ # SPI master controller drivers (bus)
++obj-$(CONFIG_SPI_AR71XX) += ar71xx_spi.o
+ obj-$(CONFIG_SPI_ATMEL) += atmel_spi.o
+ obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o
+ obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o
--- /dev/null
+--- a/drivers/net/Kconfig
++++ b/drivers/net/Kconfig
+@@ -2128,6 +2128,8 @@ config ACENIC_OMIT_TIGON_I
+
+ The safe and default value for this is N.
+
++source drivers/net/ag71xx/Kconfig
++
+ config DL2K
+ tristate "DL2000/TC902x-based Gigabit Ethernet support"
+ depends on PCI
+--- a/drivers/net/Makefile
++++ b/drivers/net/Makefile
+@@ -106,6 +106,7 @@ obj-$(CONFIG_STMMAC_ETH) += stmmac/
+ # end link order section
+ #
+
++obj-$(CONFIG_AG71XX) += ag71xx/
+ obj-$(CONFIG_SUNDANCE) += sundance.o
+ obj-$(CONFIG_HAMACHI) += hamachi.o
+ obj-$(CONFIG_NET) += Space.o loopback.o
--- /dev/null
+--- a/drivers/watchdog/Kconfig
++++ b/drivers/watchdog/Kconfig
+@@ -840,6 +840,13 @@ config TXX9_WDT
+ help
+ Hardware driver for the built-in watchdog timer on TXx9 MIPS SoCs.
+
++config AR71XX_WDT
++ tristate "Atheros AR71xx Watchdog Timer"
++ depends on ATHEROS_AR71XX
++ help
++ Hardware driver for the built-in watchdog timer on the Atheros
++ AR71xx SoCs.
++
+ # PARISC Architecture
+
+ # POWERPC Architecture
+--- a/drivers/watchdog/Makefile
++++ b/drivers/watchdog/Makefile
+@@ -112,6 +112,7 @@ obj-$(CONFIG_PNX833X_WDT) += pnx833x_wdt
+ obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
+ obj-$(CONFIG_AR7_WDT) += ar7_wdt.o
+ obj-$(CONFIG_TXX9_WDT) += txx9wdt.o
++obj-$(CONFIG_AR71XX_WDT) += ar71xx_wdt.o
+
+ # PARISC Architecture
+
--- /dev/null
+--- a/drivers/mtd/maps/Kconfig
++++ b/drivers/mtd/maps/Kconfig
+@@ -257,6 +257,13 @@ config MTD_ALCHEMY
+ help
+ Flash memory access on AMD Alchemy Pb/Db/RDK Reference Boards
+
++config MTD_AR91XX_FLASH
++ tristate "Atheros AR91xx parallel flash support"
++ depends on ATHEROS_AR71XX
++ select MTD_COMPLEX_MAPPINGS
++ help
++ Parallel flash driver for the Atheros AR91xx based boards.
++
+ config MTD_DILNETPC
+ tristate "CFI Flash device mapped on DIL/Net PC"
+ depends on X86 && MTD_CONCAT && MTD_PARTITIONS && MTD_CFI_INTELEXT && BROKEN
+--- a/drivers/mtd/maps/Makefile
++++ b/drivers/mtd/maps/Makefile
+@@ -40,6 +40,7 @@
+ obj-$(CONFIG_MTD_DBOX2) += dbox2-flash.o
+ obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
+ obj-$(CONFIG_MTD_PCI) += pci.o
++obj-$(CONFIG_MTD_AR91XX_FLASH) += ar91xx_flash.o
+ obj-$(CONFIG_MTD_AUTCPU12) += autcpu12-nvram.o
+ obj-$(CONFIG_MTD_EDB7312) += edb7312.o
+ obj-$(CONFIG_MTD_IMPA7) += impa7.o
--- /dev/null
+--- a/drivers/net/phy/Kconfig
++++ b/drivers/net/phy/Kconfig
+@@ -114,6 +114,11 @@ config RTL8306_PHY
+ tristate "Driver for Realtek RTL8306S switches"
+ select SWCONFIG
+
++config MICREL_PHY
++ tristate "Drivers for Micrel/Kendin PHYs"
++ ---help---
++ Currently has a driver for the KSZ8041
++
+ config FIXED_PHY
+ bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"
+ depends on PHYLIB=y
+--- a/drivers/net/phy/Makefile
++++ b/drivers/net/phy/Makefile
+@@ -24,6 +24,7 @@ obj-$(CONFIG_RTL8366_SMI) += rtl8366_smi
+ obj-$(CONFIG_RTL8366S_PHY) += rtl8366s.o
+ obj-$(CONFIG_RTL8366RB_PHY) += rtl8366rb.o
+ obj-$(CONFIG_LSI_ET1011C_PHY) += et1011c.o
++obj-$(CONFIG_MICREL) += micrel.o
+ obj-$(CONFIG_FIXED_PHY) += fixed.o
+ obj-$(CONFIG_MDIO_BITBANG) += mdio-bitbang.o
+ obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o
--- /dev/null
+--- a/drivers/mtd/devices/m25p80.c
++++ b/drivers/mtd/devices/m25p80.c
+@@ -922,6 +922,16 @@ static int __devinit m25p_probe(struct s
+ part_probes, &parts, 0);
+ }
+
++#ifdef CONFIG_MTD_MYLOADER_PARTS
++ if (nr_parts <= 0) {
++ static const char *part_probes[]
++ = { "MyLoader", NULL, };
++
++ nr_parts = parse_mtd_partitions(&flash->mtd,
++ part_probes, &parts, 0);
++ }
++#endif
++
+ if (nr_parts <= 0 && data && data->parts) {
+ parts = data->parts;
+ nr_parts = data->nr_parts;
--- /dev/null
+--- a/drivers/mtd/devices/m25p80.c
++++ b/drivers/mtd/devices/m25p80.c
+@@ -932,6 +932,15 @@ static int __devinit m25p_probe(struct s
+ }
+ #endif
+
++#ifdef CONFIG_MTD_REDBOOT_PARTS
++ if (nr_parts <= 0) {
++ static const char *part_probes[]
++ = { "RedBoot", NULL, };
++
++ nr_parts = parse_mtd_partitions(&flash->mtd,
++ part_probes, &parts, 0);
++ }
++#endif
+ if (nr_parts <= 0 && data && data->parts) {
+ parts = data->parts;
+ nr_parts = data->nr_parts;
--- /dev/null
+--- a/drivers/mtd/chips/jedec_probe.c
++++ b/drivers/mtd/chips/jedec_probe.c
+@@ -166,6 +166,7 @@
+ #define SST39LF160 0x2782
+ #define SST39VF1601 0x234b
+ #define SST39VF3201 0x235b
++#define SST39VF6401B 0x236d
+ #define SST39LF512 0x00D4
+ #define SST39LF010 0x00D5
+ #define SST39LF020 0x00D6
+@@ -1556,6 +1557,18 @@ static const struct amd_flash_info jedec
+ ERASEINFO(0x10000,64),
+ }
+ }, {
++ .mfr_id = MANUFACTURER_SST,
++ .dev_id = SST39VF6401B,
++ .name = "SST 39VF6401B",
++ .devtypes = CFI_DEVICETYPE_X16,
++ .uaddr = MTD_UADDR_0xAAAA_0x5555,
++ .dev_size = SIZE_8MiB,
++ .cmd_set = P_ID_AMD_STD,
++ .nr_regions = 1,
++ .regions = {
++ ERASEINFO(0x10000,128)
++ }
++ }, {
+ .mfr_id = MANUFACTURER_ST,
+ .dev_id = M29F800AB,
+ .name = "ST M29F800AB",
--- /dev/null
+--- a/drivers/mtd/chips/cfi_cmdset_0002.c
++++ b/drivers/mtd/chips/cfi_cmdset_0002.c
+@@ -1130,8 +1130,8 @@ static int __xipram do_write_oneword(str
+ break;
+ }
+
+- if (chip_ready(map, adr))
+- break;
++ if (chip_good(map, adr, datum))
++ goto enable_xip;
+
+ /* Latency issues. Drop the lock, wait a while and retry */
+ UDELAY(map, chip, adr, 1);
+@@ -1147,6 +1147,8 @@ static int __xipram do_write_oneword(str
+
+ ret = -EIO;
+ }
++
++ enable_xip:
+ xip_enable(map, chip, adr);
+ op_done:
+ chip->state = FL_READY;
+@@ -1493,7 +1495,6 @@ static int cfi_amdstd_write_buffers(stru
+ return 0;
+ }
+
+-
+ /*
+ * Handle devices with one erase region, that only implement
+ * the chip erase command.
+@@ -1557,8 +1558,8 @@ static int __xipram do_erase_chip(struct
+ chip->erase_suspended = 0;
+ }
+
+- if (chip_ready(map, adr))
+- break;
++ if (chip_good(map, adr, map_word_ff(map)))
++ goto op_done;
+
+ if (time_after(jiffies, timeo)) {
+ printk(KERN_WARNING "MTD %s(): software timeout\n",
+@@ -1578,6 +1579,7 @@ static int __xipram do_erase_chip(struct
+ ret = -EIO;
+ }
+
++ op_done:
+ chip->state = FL_READY;
+ xip_enable(map, chip, adr);
+ put_chip(map, chip, adr);
+@@ -1645,9 +1647,9 @@ static int __xipram do_erase_oneblock(st
+ chip->erase_suspended = 0;
+ }
+
+- if (chip_ready(map, adr)) {
++ if (chip_good(map, adr, map_word_ff(map))) {
+ xip_enable(map, chip, adr);
+- break;
++ goto op_done;
+ }
+
+ if (time_after(jiffies, timeo)) {
+@@ -1669,6 +1671,7 @@ static int __xipram do_erase_oneblock(st
+ ret = -EIO;
+ }
+
++ op_done:
+ chip->state = FL_READY;
+ put_chip(map, chip, adr);
+ spin_unlock(chip->mutex);
--- /dev/null
+--- a/drivers/mtd/devices/m25p80.c
++++ b/drivers/mtd/devices/m25p80.c
+@@ -941,6 +941,16 @@ static int __devinit m25p_probe(struct s
+ part_probes, &parts, 0);
+ }
+ #endif
++
++#ifdef CONFIG_MTD_WRT160NL_PARTS
++ if (nr_parts <= 0) {
++ static const char *part_probes[]
++ = { "wrt160nl", NULL, };
++
++ nr_parts = parse_mtd_partitions(&flash->mtd,
++ part_probes, &parts, 0);
++ }
++#endif
+ if (nr_parts <= 0 && data && data->parts) {
+ parts = data->parts;
+ nr_parts = data->nr_parts;
+--- a/drivers/mtd/Kconfig
++++ b/drivers/mtd/Kconfig
+@@ -181,6 +181,12 @@ config MTD_AR7_PARTS
+ ---help---
+ TI AR7 partitioning support
+
++config MTD_WRT160NL_PARTS
++ tristate "Linksys WRT160NL partitioning support"
++ depends on MTD_PARTITIONS && AR71XX_MACH_WRT160NL
++ ---help---
++ Linksys WRT160NL partitioning support
++
+ config MTD_MYLOADER_PARTS
+ tristate "MyLoader partition parsing"
+ depends on MTD_PARTITIONS && (ADM5120 || ATHEROS_AR231X || ATHEROS_AR71XX)
+--- a/drivers/mtd/Makefile
++++ b/drivers/mtd/Makefile
+@@ -12,6 +12,7 @@ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redbo
+ obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
+ obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
+ obj-$(CONFIG_MTD_AR7_PARTS) += ar7part.o
++obj-$(CONFIG_MTD_WRT160NL_PARTS) += wrt160nl_part.o
+ obj-$(CONFIG_MTD_OF_PARTS) += ofpart.o
+ obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
+
--- /dev/null
+--- a/drivers/usb/host/ehci-q.c
++++ b/drivers/usb/host/ehci-q.c
+@@ -1194,6 +1194,9 @@ static void end_unlink_async (struct ehc
+ ehci->reclaim = NULL;
+ start_unlink_async (ehci, next);
+ }
++
++ if (ehci->has_synopsys_hc_bug)
++ writel((u32)ehci->async->qh_dma, &ehci->regs->async_next);
+ }
+
+ /* makes sure the async qh will become idle */
+--- a/drivers/usb/host/ehci.h
++++ b/drivers/usb/host/ehci.h
+@@ -129,6 +129,7 @@ struct ehci_hcd { /* one per controlle
+ unsigned has_amcc_usb23:1;
+ unsigned need_io_watchdog:1;
+ unsigned broken_periodic:1;
++ unsigned has_synopsys_hc_bug:1; /* Synopsys HC */
+
+ /* required for usb32 quirk */
+ #define OHCI_CTRL_HCFS (3 << 6)
--- /dev/null
+--- a/drivers/mtd/chips/cfi_cmdset_0002.c
++++ b/drivers/mtd/chips/cfi_cmdset_0002.c
+@@ -39,7 +39,7 @@
+ #include <linux/mtd/xip.h>
+
+ #define AMD_BOOTLOC_BUG
+-#define FORCE_WORD_WRITE 0
++#define FORCE_WORD_WRITE 1
+
+ #define MAX_WORD_RETRIES 3
+
+@@ -55,7 +55,9 @@
+
+ static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
+ static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
++#if !FORCE_WORD_WRITE
+ static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
++#endif
+ static int cfi_amdstd_erase_chip(struct mtd_info *, struct erase_info *);
+ static int cfi_amdstd_erase_varsize(struct mtd_info *, struct erase_info *);
+ static void cfi_amdstd_sync (struct mtd_info *);
+@@ -190,6 +192,7 @@ static void fixup_amd_bootblock(struct m
+ }
+ #endif
+
++#if !FORCE_WORD_WRITE
+ static void fixup_use_write_buffers(struct mtd_info *mtd, void *param)
+ {
+ struct map_info *map = mtd->priv;
+@@ -199,6 +202,7 @@ static void fixup_use_write_buffers(stru
+ mtd->write = cfi_amdstd_write_buffers;
+ }
+ }
++#endif /* !FORCE_WORD_WRITE */
+
+ /* Atmel chips don't use the same PRI format as AMD chips */
+ static void fixup_convert_atmel_pri(struct mtd_info *mtd, void *param)
+@@ -1304,6 +1308,7 @@ static int cfi_amdstd_write_words(struct
+ /*
+ * FIXME: interleaved mode not tested, and probably not supported!
+ */
++#if !FORCE_WORD_WRITE
+ static int __xipram do_write_buffer(struct map_info *map, struct flchip *chip,
+ unsigned long adr, const u_char *buf,
+ int len)
+@@ -1415,7 +1420,6 @@ static int __xipram do_write_buffer(stru
+ return ret;
+ }
+
+-
+ static int cfi_amdstd_write_buffers(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+ {
+@@ -1494,6 +1498,7 @@ static int cfi_amdstd_write_buffers(stru
+
+ return 0;
+ }
++#endif /* !FORCE_WORD_WRITE */
+
+ /*
+ * Handle devices with one erase region, that only implement
--- /dev/null
+--- a/net/dsa/tag_trailer.c
++++ b/net/dsa/tag_trailer.c
+@@ -86,7 +86,7 @@ static int trailer_rcv(struct sk_buff *s
+
+ trailer = skb_tail_pointer(skb) - 4;
+ if (trailer[0] != 0x80 || (trailer[1] & 0xf8) != 0x00 ||
+- (trailer[3] & 0xef) != 0x00 || trailer[3] != 0x00)
++ (trailer[2] & 0xef) != 0x00 || (trailer[3] & 0xfe) != 0x00)
+ goto out_drop;
+
+ source_port = trailer[1] & 7;
--- /dev/null
+--- a/net/dsa/Kconfig
++++ b/net/dsa/Kconfig
+@@ -36,6 +36,13 @@ config NET_DSA_MV88E6060
+ This enables support for the Marvell 88E6060 ethernet switch
+ chip.
+
++config NET_DSA_MV88E6063
++ bool "Marvell 88E6063 ethernet switch chip support"
++ select NET_DSA_TAG_TRAILER
++ ---help---
++ This enables support for the Marvell 88E6063 ethernet switch
++ chip
++
+ config NET_DSA_MV88E6XXX_NEED_PPU
+ bool
+ default n
+--- a/net/dsa/Makefile
++++ b/net/dsa/Makefile
+@@ -6,6 +6,7 @@ obj-$(CONFIG_NET_DSA_TAG_TRAILER) += tag
+ # switch drivers
+ obj-$(CONFIG_NET_DSA_MV88E6XXX) += mv88e6xxx.o
+ obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
++obj-$(CONFIG_NET_DSA_MV88E6063) += mv88e6063.o
+ obj-$(CONFIG_NET_DSA_MV88E6123_61_65) += mv88e6123_61_65.o
+ obj-$(CONFIG_NET_DSA_MV88E6131) += mv88e6131.o
+
--- /dev/null
+--- a/include/linux/if_ether.h
++++ b/include/linux/if_ether.h
+@@ -81,6 +81,7 @@
+ #define ETH_P_1588 0x88F7 /* IEEE 1588 Timesync */
+ #define ETH_P_FCOE 0x8906 /* Fibre Channel over Ethernet */
+ #define ETH_P_FIP 0x8914 /* FCoE Initialization Protocol */
++#define ETH_P_QINQ 0x9100 /* QinQ VLAN Stacking Protocol */
+ #define ETH_P_EDSA 0xDADA /* Ethertype DSA [ NOT AN OFFICIALLY REGISTERED ID ] */
+
+ /*
+--- a/net/dsa/dsa_priv.h
++++ b/net/dsa/dsa_priv.h
+@@ -174,6 +174,9 @@ netdev_tx_t dsa_xmit(struct sk_buff *skb
+ /* tag_edsa.c */
+ netdev_tx_t edsa_xmit(struct sk_buff *skb, struct net_device *dev);
+
++/* tag_qinq.c */
++netdev_tx_t qinq_xmit(struct sk_buff *skb, struct net_device *dev);
++
+ /* tag_trailer.c */
+ netdev_tx_t trailer_xmit(struct sk_buff *skb, struct net_device *dev);
+
+--- a/net/dsa/Kconfig
++++ b/net/dsa/Kconfig
+@@ -23,6 +23,10 @@ config NET_DSA_TAG_TRAILER
+ bool
+ default n
+
++config NET_DSA_TAG_QINQ
++ bool
++ default y
++
+
+ # switch drivers
+ config NET_DSA_MV88E6XXX
+--- a/net/dsa/Makefile
++++ b/net/dsa/Makefile
+@@ -1,6 +1,7 @@
+ # tagging formats
+ obj-$(CONFIG_NET_DSA_TAG_DSA) += tag_dsa.o
+ obj-$(CONFIG_NET_DSA_TAG_EDSA) += tag_edsa.o
++obj-$(CONFIG_NET_DSA_TAG_QINQ) += tag_qinq.o
+ obj-$(CONFIG_NET_DSA_TAG_TRAILER) += tag_trailer.o
+
+ # switch drivers
+--- a/net/dsa/slave.c
++++ b/net/dsa/slave.c
+@@ -321,6 +321,19 @@ static const struct net_device_ops edsa_
+ .ndo_do_ioctl = dsa_slave_ioctl,
+ };
+ #endif
++#ifdef CONFIG_NET_DSA_TAG_QINQ
++static const struct net_device_ops qinq_netdev_ops = {
++ .ndo_init = dsa_slave_init,
++ .ndo_open = dsa_slave_open,
++ .ndo_stop = dsa_slave_close,
++ .ndo_start_xmit = qinq_xmit,
++ .ndo_change_rx_flags = dsa_slave_change_rx_flags,
++ .ndo_set_rx_mode = dsa_slave_set_rx_mode,
++ .ndo_set_multicast_list = dsa_slave_set_rx_mode,
++ .ndo_set_mac_address = dsa_slave_set_mac_address,
++ .ndo_do_ioctl = dsa_slave_ioctl,
++};
++#endif
+ #ifdef CONFIG_NET_DSA_TAG_TRAILER
+ static const struct net_device_ops trailer_netdev_ops = {
+ .ndo_init = dsa_slave_init,
+@@ -366,6 +379,11 @@ dsa_slave_create(struct dsa_switch *ds,
+ slave_dev->netdev_ops = &edsa_netdev_ops;
+ break;
+ #endif
++#ifdef CONFIG_NET_DSA_TAG_QINQ
++ case htons(ETH_P_QINQ):
++ slave_dev->netdev_ops = &qinq_netdev_ops;
++ break;
++#endif
+ #ifdef CONFIG_NET_DSA_TAG_TRAILER
+ case htons(ETH_P_TRAILER):
+ slave_dev->netdev_ops = &trailer_netdev_ops;
--- /dev/null
+--- a/net/dsa/Kconfig
++++ b/net/dsa/Kconfig
+@@ -29,6 +29,15 @@ config NET_DSA_TAG_QINQ
+
+
+ # switch drivers
++config NET_DSA_AR7240
++ bool "Atheros AR7240 built-in ethernet switch support"
++ depends on ATHEROS_AR71XX
++ default n
++ select NET_DSA_TAG_QINQ
++ ---help---
++ This enables support for the built-in ethernet switch of the
++ Atheros AR7240 SoC.
++
+ config NET_DSA_MV88E6XXX
+ bool
+ default n
+--- a/net/dsa/Makefile
++++ b/net/dsa/Makefile
+@@ -5,6 +5,7 @@ obj-$(CONFIG_NET_DSA_TAG_QINQ) += tag_qi
+ obj-$(CONFIG_NET_DSA_TAG_TRAILER) += tag_trailer.o
+
+ # switch drivers
++obj-$(CONFIG_NET_DSA_AR7240) += ar7240.o
+ obj-$(CONFIG_NET_DSA_MV88E6XXX) += mv88e6xxx.o
+ obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
+ obj-$(CONFIG_NET_DSA_MV88E6063) += mv88e6063.o
--- /dev/null
+--- a/drivers/mtd/redboot.c
++++ b/drivers/mtd/redboot.c
+@@ -60,31 +60,32 @@ static int parse_redboot_partitions(stru
+ static char nullstring[] = "unallocated";
+ #endif
+
++ buf = vmalloc(master->erasesize);
++ if (!buf)
++ return -ENOMEM;
++
++ restart:
+ if ( directory < 0 ) {
+ offset = master->size + directory * master->erasesize;
+- while (master->block_isbad &&
++ while (master->block_isbad &&
+ master->block_isbad(master, offset)) {
+ if (!offset) {
+ nogood:
+ printk(KERN_NOTICE "Failed to find a non-bad block to check for RedBoot partition table\n");
++ vfree(buf);
+ return -EIO;
+ }
+ offset -= master->erasesize;
+ }
+ } else {
+ offset = directory * master->erasesize;
+- while (master->block_isbad &&
++ while (master->block_isbad &&
+ master->block_isbad(master, offset)) {
+ offset += master->erasesize;
+ if (offset == master->size)
+ goto nogood;
+ }
+ }
+- buf = vmalloc(master->erasesize);
+-
+- if (!buf)
+- return -ENOMEM;
+-
+ printk(KERN_NOTICE "Searching for RedBoot partition table in %s at offset 0x%lx\n",
+ master->name, offset);
+
+@@ -156,6 +157,11 @@ static int parse_redboot_partitions(stru
+ }
+ if (i == numslots) {
+ /* Didn't find it */
++ if (offset + master->erasesize < master->size) {
++ /* not at the end of the flash yet, maybe next block :) */
++ directory++;
++ goto restart;
++ }
+ printk(KERN_NOTICE "No RedBoot partition table detected in %s\n",
+ master->name);
+ ret = 0;
--- /dev/null
+--- a/drivers/mtd/nand/Kconfig
++++ b/drivers/mtd/nand/Kconfig
+@@ -488,4 +488,8 @@ config MTD_NAND_W90P910
+ This enables the driver for the NAND Flash on evaluation board based
+ on w90p910.
+
++config MTD_NAND_RB4XX
++ tristate "NAND flash driver for RouterBoard 4xx series"
++ depends on MTD_NAND && AR71XX_MACH_RB4XX
++
+ endif # MTD_NAND
+--- a/drivers/mtd/nand/Makefile
++++ b/drivers/mtd/nand/Makefile
+@@ -30,6 +30,7 @@ obj-$(CONFIG_MTD_NAND_CM_X270) += cmx27
+ obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx_nand.o
+ obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o
+ obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o
++obj-$(CONFIG_MTD_NAND_RB4XX) += rb4xx_nand.o
+ obj-$(CONFIG_MTD_ALAUDA) += alauda.o
+ obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o
+ obj-$(CONFIG_MTD_NAND_ORION) += orion_nand.o
--- /dev/null
+--- a/drivers/spi/Makefile
++++ b/drivers/spi/Makefile
+@@ -11,6 +11,7 @@ endif
+ obj-$(CONFIG_SPI_MASTER) += spi.o
+
+ # SPI master controller drivers (bus)
++obj-$(CONFIG_SPI_AP83) += ap83_spi.o
+ obj-$(CONFIG_SPI_AR71XX) += ar71xx_spi.o
+ obj-$(CONFIG_SPI_ATMEL) += atmel_spi.o
+ obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o
+--- a/drivers/spi/Kconfig
++++ b/drivers/spi/Kconfig
+@@ -53,6 +53,14 @@ if SPI_MASTER
+
+ comment "SPI Master Controller Drivers"
+
++config SPI_AP83
++ tristate "Atheros AP83 specific SPI Controller"
++ depends on SPI_MASTER && AR71XX_MACH_AP83
++ select SPI_BITBANG
++ help
++ This is a specific SPI controller driver for the Atheros AP83
++ reference board.
++
+ config SPI_AR71XX
+ tristate "Atheros AR71xx SPI Controller"
+ depends on SPI_MASTER && ATHEROS_AR71XX
--- /dev/null
+--- a/drivers/spi/Kconfig
++++ b/drivers/spi/Kconfig
+@@ -365,6 +365,11 @@ config SPI_TLE62X0
+ sysfs interface, with each line presented as a kind of GPIO
+ exposing both switch control and diagnostic feedback.
+
++config SPI_VSC7385
++ tristate "Vitesse VSC7385 ethernet switch driver"
++ help
++ SPI driver for the Vitesse VSC7385 ethernet switch.
++
+ #
+ # Add new SPI protocol masters in alphabetical order above this line
+ #
+--- a/drivers/spi/Makefile
++++ b/drivers/spi/Makefile
+@@ -54,6 +54,7 @@ spi_s3c24xx_hw-$(CONFIG_SPI_S3C24XX_FIQ)
+
+ # SPI protocol drivers (device/link on bus)
+ obj-$(CONFIG_SPI_SPIDEV) += spidev.o
++obj-$(CONFIG_SPI_VSC7385) += spi_vsc7385.o
+ obj-$(CONFIG_SPI_TLE62X0) += tle62x0.o
+ # ... add above this line ...
+
--- /dev/null
+--- a/drivers/spi/Kconfig
++++ b/drivers/spi/Kconfig
+@@ -68,6 +68,14 @@ config SPI_AR71XX
+ help
+ This is the SPI contoller driver for Atheros AR71xx.
+
++config SPI_PB44
++ tristate "Atheros PB44 board specific SPI controller"
++ depends on SPI_MASTER && AR71XX_MACH_PB44
++ select SPI_BITBANG
++ help
++ This is a specific SPI controller driver for the Atheros PB44
++ reference board.
++
+ config SPI_ATMEL
+ tristate "Atmel SPI Controller"
+ depends on (ARCH_AT91 || AVR32)
+--- a/drivers/spi/Makefile
++++ b/drivers/spi/Makefile
+@@ -24,6 +24,7 @@ obj-$(CONFIG_SPI_GPIO) += spi_gpio.o
+ obj-$(CONFIG_SPI_GPIO_OLD) += spi_gpio_old.o
+ obj-$(CONFIG_SPI_IMX) += spi_imx.o
+ obj-$(CONFIG_SPI_LM70_LLP) += spi_lm70llp.o
++obj-$(CONFIG_SPI_PB44) += pb44_spi.o
+ obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o
+ obj-$(CONFIG_SPI_OMAP_UWIRE) += omap_uwire.o
+ obj-$(CONFIG_SPI_OMAP24XX) += omap2_mcspi.o
--- /dev/null
+--- a/drivers/leds/Kconfig
++++ b/drivers/leds/Kconfig
+@@ -269,6 +269,13 @@ config LEDS_ADP5520
+ To compile this driver as a module, choose M here: the module will
+ be called leds-adp5520.
+
++config LEDS_WNDR3700_USB
++ tristate "NETGEAR WNDR3700 USB LED driver"
++ depends on LEDS_CLASS && AR71XX_MACH_WNDR3700
++ help
++ This option enables support for the USB LED found on the
++ NETGEAR WNDR3700 board.
++
+ comment "LED Triggers"
+
+ config LEDS_TRIGGERS
+--- a/drivers/leds/Makefile
++++ b/drivers/leds/Makefile
+@@ -29,6 +29,7 @@ obj-$(CONFIG_LEDS_DA903X) += leds-da903
+ obj-$(CONFIG_LEDS_WM831X_STATUS) += leds-wm831x-status.o
+ obj-$(CONFIG_LEDS_WM8350) += leds-wm8350.o
+ obj-$(CONFIG_LEDS_PWM) += leds-pwm.o
++obj-${CONFIG_LEDS_WNDR3700_USB} += leds-wndr3700-usb.o
+ obj-$(CONFIG_LEDS_REGULATOR) += leds-regulator.o
+ obj-$(CONFIG_LEDS_INTEL_SS4200) += leds-ss4200.o
+ obj-$(CONFIG_LEDS_LT3593) += leds-lt3593.o
--- /dev/null
+--- a/drivers/gpio/Kconfig
++++ b/drivers/gpio/Kconfig
+@@ -255,4 +255,12 @@ config GPIO_UCB1400
+ To compile this driver as a module, choose M here: the
+ module will be called ucb1400_gpio.
+
++comment "Other GPIO expanders"
++
++config GPIO_NXP_74HC153
++ tristate "NXP 74HC153 Dual 4-input multiplexer"
++ help
++ Platform driver for NXP 74HC153 Dual 4-input Multiplexer. This
++ provides a GPIO interface supporting inputs.
++
+ endif
+--- a/drivers/gpio/Makefile
++++ b/drivers/gpio/Makefile
+@@ -11,6 +11,7 @@ obj-$(CONFIG_GPIO_MAX7301) += max7301.o
+ obj-$(CONFIG_GPIO_MAX732X) += max732x.o
+ obj-$(CONFIG_GPIO_MC33880) += mc33880.o
+ obj-$(CONFIG_GPIO_MCP23S08) += mcp23s08.o
++obj-$(CONFIG_GPIO_NXP_74HC153) += nxp_74hc153.o
+ obj-$(CONFIG_GPIO_PCA953X) += pca953x.o
+ obj-$(CONFIG_GPIO_PCF857X) += pcf857x.o
+ obj-$(CONFIG_GPIO_PL061) += pl061.o
--- /dev/null
+--- a/drivers/leds/Kconfig
++++ b/drivers/leds/Kconfig
+@@ -276,6 +276,10 @@ config LEDS_WNDR3700_USB
+ This option enables support for the USB LED found on the
+ NETGEAR WNDR3700 board.
+
++config LEDS_RB750
++ tristate "LED driver for the Mikrotik RouterBOARD 750"
++ depends on LEDS_CLASS && AR71XX_MACH_RB750
++
+ comment "LED Triggers"
+
+ config LEDS_TRIGGERS
+--- a/drivers/leds/Makefile
++++ b/drivers/leds/Makefile
+@@ -34,6 +34,7 @@ obj-$(CONFIG_LEDS_REGULATOR) += leds-re
+ obj-$(CONFIG_LEDS_INTEL_SS4200) += leds-ss4200.o
+ obj-$(CONFIG_LEDS_LT3593) += leds-lt3593.o
+ obj-$(CONFIG_LEDS_ADP5520) += leds-adp5520.o
++obj-$(CONFIG_LEDS_RB750) += leds-rb750.o
+
+ # LED SPI Drivers
+ obj-$(CONFIG_LEDS_DAC124S085) += leds-dac124s085.o
--- /dev/null
+--- a/drivers/mtd/nand/Kconfig
++++ b/drivers/mtd/nand/Kconfig
+@@ -492,4 +492,8 @@ config MTD_NAND_RB4XX
+ tristate "NAND flash driver for RouterBoard 4xx series"
+ depends on MTD_NAND && AR71XX_MACH_RB4XX
+
++config MTD_NAND_RB750
++ tristate "NAND flash driver for the RouterBoard 750"
++ depends on MTD_NAND && AR71XX_MACH_RB750
++
+ endif # MTD_NAND
+--- a/drivers/mtd/nand/Makefile
++++ b/drivers/mtd/nand/Makefile
+@@ -31,6 +31,7 @@ obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx
+ obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o
+ obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o
+ obj-$(CONFIG_MTD_NAND_RB4XX) += rb4xx_nand.o
++obj-$(CONFIG_MTD_NAND_RB750) += rb750_nand.o
+ obj-$(CONFIG_MTD_ALAUDA) += alauda.o
+ obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o
+ obj-$(CONFIG_MTD_NAND_ORION) += orion_nand.o
--- /dev/null
+--- a/arch/mips/Makefile
++++ b/arch/mips/Makefile
+@@ -181,6 +181,7 @@ endif
+ #
+ libs-$(CONFIG_ARC) += arch/mips/fw/arc/
+ libs-$(CONFIG_CFE) += arch/mips/fw/cfe/
++libs-$(CONFIG_MYLOADER) += arch/mips/fw/myloader/
+ libs-$(CONFIG_SNIPROM) += arch/mips/fw/sni/
+ libs-y += arch/mips/fw/lib/
+
+--- a/arch/mips/Kconfig
++++ b/arch/mips/Kconfig
+@@ -877,6 +877,9 @@ config MIPS_NILE4
+ config MIPS_DISABLE_OBSOLETE_IDE
+ bool
+
++config MYLOADER
++ bool
++
+ config SYNC_R4K
+ bool
+
--- /dev/null
+--- a/arch/mips/kernel/mips_machine.c
++++ b/arch/mips/kernel/mips_machine.c
+@@ -7,12 +7,13 @@
+ *
+ */
+ #include <linux/mm.h>
++#include <linux/string.h>
+
+ #include <asm/mips_machine.h>
+-#include <asm/bootinfo.h>
+
+ static struct list_head mips_machines __initdata =
+ LIST_HEAD_INIT(mips_machines);
++static char *mips_machid __initdata;
+
+ char *mips_machine_name = "Unknown";
+
+@@ -55,20 +56,65 @@ void __init mips_machine_set_name(char *
+ }
+ }
+
+-void __init mips_machine_setup(unsigned long machtype)
++void __init mips_machine_setup(void)
+ {
+ struct mips_machine *mach;
+
+- mach = mips_machine_find(machtype);
++ mach = mips_machine_find(mips_machtype);
+ if (!mach) {
+- printk(KERN_ALERT "MIPS: no machine registered for "
+- "machtype %lu\n", machtype);
++ printk(KERN_WARNING "MIPS: no machine registered for "
++ "machtype %lu\n", mips_machtype);
+ return;
+ }
+
+ mips_machine_set_name(mach->mach_name);
+- printk(KERN_INFO "MIPS: machine is %s\n", mips_machine_name);
++ printk(KERN_NOTICE "MIPS: machine is %s\n", mips_machine_name);
+
+ if (mach->mach_setup)
+ mach->mach_setup();
+ }
++
++int __init mips_machtype_setup(char *id)
++{
++ if (mips_machid == NULL)
++ mips_machid = id;
++
++ return 1;
++}
++
++__setup("machtype=", mips_machtype_setup);
++
++static int __init mips_machtype_init(void)
++{
++ struct list_head *this;
++ struct mips_machine *mach;
++
++ if (mips_machid == NULL)
++ return 0;
++
++ list_for_each(this, &mips_machines) {
++ mach = list_entry(this, struct mips_machine, list);
++ if (mach->mach_id == NULL)
++ continue;
++
++ if (strcmp(mach->mach_id, mips_machid) == 0) {
++ mips_machtype = mach->mach_type;
++ return 0;
++ }
++ }
++
++ printk(KERN_WARNING
++ "MIPS: no machine found for id: '%s', registered machines:\n",
++ mips_machid);
++ printk(KERN_WARNING "%32s %s\n", "id", "name");
++
++ list_for_each(this, &mips_machines) {
++ mach = list_entry(this, struct mips_machine, list);
++ printk(KERN_WARNING "%32s %s\n",
++ mach->mach_id ? mach->mach_id : "", mach->mach_name);
++ }
++
++ return 0;
++}
++
++core_initcall(mips_machtype_init);
+--- a/arch/mips/include/asm/mips_machine.h
++++ b/arch/mips/include/asm/mips_machine.h
+@@ -13,25 +13,33 @@
+ #include <linux/init.h>
+ #include <linux/list.h>
+
++#include <asm/bootinfo.h>
++
+ struct mips_machine {
+ unsigned long mach_type;
+- void (*mach_setup)(void);
++ char *mach_id;
+ char *mach_name;
++ void (*mach_setup)(void);
+ struct list_head list;
+ };
+
+ void mips_machine_register(struct mips_machine *) __init;
+-void mips_machine_setup(unsigned long machtype) __init;
++void mips_machine_setup(void) __init;
++int mips_machtype_setup(char *id) __init;
+ void mips_machine_set_name(char *name) __init;
+
+ extern char *mips_machine_name;
+
+-#define MIPS_MACHINE(_type, _name, _setup) \
+-static char machine_name_##_type[] __initdata = _name; \
++#define MIPS_MACHINE(_type, _id, _name, _setup) \
++static const char machine_name_##_type[] __initconst \
++ __aligned(1) = _name; \
++static const char machine_id_##_type[] __initconst \
++ __aligned(1) = _id; \
+ static struct mips_machine machine_##_type __initdata = \
+ { \
+ .mach_type = _type, \
+- .mach_name = machine_name_##_type, \
++ .mach_id = (char *) machine_id_##_type, \
++ .mach_name = (char *) machine_name_##_type, \
+ .mach_setup = _setup, \
+ }; \
+ \
+@@ -44,4 +52,3 @@ static int __init register_machine_##_ty
+ pure_initcall(register_machine_##_type)
+
+ #endif /* __ASM_MIPS_MACHINE_H */
+-
--- /dev/null
+--- a/arch/mips/kernel/traps.c
++++ b/arch/mips/kernel/traps.c
+@@ -51,6 +51,7 @@
+ #include <asm/stacktrace.h>
+ #include <asm/irq.h>
+ #include <asm/uasm.h>
++#include <asm/time.h>
+
+ extern void check_wait(void);
+ extern asmlinkage void r4k_wait(void);
+@@ -1501,6 +1502,8 @@
+ if (cpu_has_mips_r2) {
+ cp0_compare_irq_shift = CAUSEB_TI - CAUSEB_IP;
+ cp0_compare_irq = (read_c0_intctl() >> INTCTLB_IPTI) & 7;
++ if (get_c0_compare_irq)
++ cp0_compare_irq = get_c0_compare_irq();
+ cp0_perfcount_irq = (read_c0_intctl() >> INTCTLB_IPPCI) & 7;
+ if (cp0_perfcount_irq == cp0_compare_irq)
+ cp0_perfcount_irq = -1;
+--- a/arch/mips/include/asm/time.h
++++ b/arch/mips/include/asm/time.h
+@@ -52,6 +52,7 @@ extern int (*perf_irq)(void);
+ */
+ #ifdef CONFIG_CEVT_R4K_LIB
+ extern unsigned int __weak get_c0_compare_int(void);
++extern unsigned int __weak get_c0_compare_irq(void);
+ extern int r4k_clockevent_init(void);
+ #endif
+
--- /dev/null
+--- a/arch/mips/kernel/cevt-r4k.c
++++ b/arch/mips/kernel/cevt-r4k.c
+@@ -16,6 +16,22 @@
+ #include <asm/cevt-r4k.h>
+
+ /*
++ * Compare interrupt can be routed and latched outside the core,
++ * so a single execution hazard barrier may not be enough to give
++ * it time to clear as seen in the Cause register. 4 time the
++ * pipeline depth seems reasonably conservative, and empirically
++ * works better in configurations with high CPU/bus clock ratios.
++ */
++
++#define compare_change_hazard() \
++ do { \
++ irq_disable_hazard(); \
++ irq_disable_hazard(); \
++ irq_disable_hazard(); \
++ irq_disable_hazard(); \
++ } while (0)
++
++/*
+ * The SMTC Kernel for the 34K, 1004K, et. al. replaces several
+ * of these routines with SMTC-specific variants.
+ */
+@@ -31,6 +47,7 @@ static int mips_next_event(unsigned long
+ cnt = read_c0_count();
+ cnt += delta;
+ write_c0_compare(cnt);
++ compare_change_hazard();
+ res = ((int)(read_c0_count() - cnt) > 0) ? -ETIME : 0;
+ return res;
+ }
+@@ -100,22 +117,6 @@ static int c0_compare_int_pending(void)
+ return (read_c0_cause() >> cp0_compare_irq_shift) & (1ul << CAUSEB_IP);
+ }
+
+-/*
+- * Compare interrupt can be routed and latched outside the core,
+- * so a single execution hazard barrier may not be enough to give
+- * it time to clear as seen in the Cause register. 4 time the
+- * pipeline depth seems reasonably conservative, and empirically
+- * works better in configurations with high CPU/bus clock ratios.
+- */
+-
+-#define compare_change_hazard() \
+- do { \
+- irq_disable_hazard(); \
+- irq_disable_hazard(); \
+- irq_disable_hazard(); \
+- irq_disable_hazard(); \
+- } while (0)
+-
+ int c0_compare_int_usable(void)
+ {
+ unsigned int delta;
projects / openwrt / staging / lynxis.git / commitdiff