--- /dev/null
+/*
+ * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "orion5x-mv88f5182.dtsi"
+
+/ {
+ model = "LaCie d2 Network";
+ compatible = "lacie,d2-network", "marvell,orion5x-88f5182", "marvell,orion5x";
+
+ memory {
+ reg = <0x00000000 0x4000000>; /* 64 MB */
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ linux,stdout-path = &uart0;
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
+ <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
+ <MBUS_ID(0x01, 0x0f) 0 0xfff80000 0x80000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_buttons>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ front_button {
+ label = "Front Push Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_rocker_sw_on {
+ label = "Power rocker switch (on|auto)";
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <1>; /* D2NET_SWITCH_POWER_ON */
+ gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_rocker_sw_off {
+ label = "Power rocker switch (auto|off)";
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <2>; /* D2NET_SWITCH_POWER_OFF */
+ gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_sata0_power &pmx_sata1_power>;
+ pinctrl-names = "default";
+
+ sata0_power: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "SATA0 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ sata1_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "SATA1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&devbus_bootcs {
+ status = "okay";
+
+ devbus,keep-config;
+
+ /*
+ * Currently the MTD code does not recognize the MX29LV400CBCT
+ * as a bottom-type device. This could cause risks of
+ * accidentally erasing critical flash sectors. We thus define
+ * a single, write-protected partition covering the whole
+ * flash. TODO: once the flash part TOP/BOTTOM detection
+ * issue is sorted out in the MTD code, break this into at
+ * least three partitions: 'u-boot code', 'u-boot environment'
+ * and 'whatever is left'.
+ */
+ flash@0 {
+ compatible = "cfi-flash";
+ reg = <0 0x80000>;
+ bank-width = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "Full512Kb";
+ reg = <0 0x80000>;
+ read-only;
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy: ethernet-phy {
+ reg = <8>;
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-handle = <ðphy>;
+ };
+};
+
+&i2c {
+ status = "okay";
+ clock-frequency = <100000>;
+ #address-cells = <1>;
+
+ rtc@32 {
+ compatible = "ricoh,rs5c372b";
+ reg = <0x32>;
+ };
+
+ fan@3e {
+ compatible = "gmt,g762";
+ reg = <0x3e>;
+
+ /* Not enough HW info */
+ status = "disabled";
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c08";
+ reg = <0x50>;
+ };
+};
+
+&pinctrl {
+ pinctrl-0 = <&pmx_leds &pmx_board_id &pmx_fan_fail>;
+ pinctrl-names = "default";
+
+ pmx_board_id: pmx-board-id {
+ marvell,pins = "mpp0", "mpp1", "mpp2";
+ marvell,function = "gpio";
+ };
+
+ pmx_buttons: pmx-buttons {
+ marvell,pins = "mpp8", "mpp9", "mpp18";
+ marvell,function = "gpio";
+ };
+
+ pmx_fan_fail: pmx-fan-fail {
+ marvell,pins = "mpp5";
+ marvell,function = "gpio";
+ };
+
+ /*
+ * MPP6: Red front LED
+ * MPP16: Blue front LED blink control
+ */
+ pmx_leds: pmx-leds {
+ marvell,pins = "mpp6", "mpp16";
+ marvell,function = "gpio";
+ };
+
+ pmx_sata0_led_active: pmx-sata0-led-active {
+ marvell,pins = "mpp14";
+ marvell,function = "sata0";
+ };
+
+ pmx_sata0_power: pmx-sata0-power {
+ marvell,pins = "mpp3";
+ marvell,function = "gpio";
+ };
+
+ pmx_sata1_led_active: pmx-sata1-led-active {
+ marvell,pins = "mpp15";
+ marvell,function = "sata1";
+ };
+
+ pmx_sata1_power: pmx-sata1-power {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+
+ /*
+ * Non MPP GPIOs:
+ * GPIO 22: USB port 1 fuse (0 = Fail, 1 = Ok)
+ * GPIO 23: Blue front LED off
+ * GPIO 24: Inhibit board power off (0 = Disabled, 1 = Enabled)
+ */
+};
+
+&sata {
+ pinctrl-0 = <&pmx_sata0_led_active
+ &pmx_sata1_led_active>;
+ pinctrl-names = "default";
+ status = "okay";
+ nr-ports = <2>;
+};
+
+&uart0 {
+ status = "okay";
+};
--- /dev/null
+/*
+ * arch/arm/mach-orion5x/board-d2net.c
+ *
+ * LaCie d2Network and Big Disk Network NAS setup
+ *
+ * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/orion5x.h>
+#include <plat/orion-gpio.h>
+#include "common.h"
+
+/*****************************************************************************
+ * LaCie d2 Network Info
+ ****************************************************************************/
+
+/*****************************************************************************
+ * GPIO LED's
+ ****************************************************************************/
+
+/*
+ * The blue front LED is wired to the CPLD and can blink in relation with the
+ * SATA activity.
+ *
+ * The following array detail the different LED registers and the combination
+ * of their possible values:
+ *
+ * led_off | blink_ctrl | SATA active | LED state
+ * | | |
+ * 1 | x | x | off
+ * 0 | 0 | 0 | off
+ * 0 | 1 | 0 | blink (rate 300ms)
+ * 0 | x | 1 | on
+ *
+ * Notes: The blue and the red front LED's can't be on at the same time.
+ * Red LED have priority.
+ */
+
+#define D2NET_GPIO_RED_LED 6
+#define D2NET_GPIO_BLUE_LED_BLINK_CTRL 16
+#define D2NET_GPIO_BLUE_LED_OFF 23
+
+static struct gpio_led d2net_leds[] = {
+ {
+ .name = "d2net:blue:sata",
+ .default_trigger = "default-on",
+ .gpio = D2NET_GPIO_BLUE_LED_OFF,
+ .active_low = 1,
+ },
+ {
+ .name = "d2net:red:fail",
+ .gpio = D2NET_GPIO_RED_LED,
+ },
+};
+
+static struct gpio_led_platform_data d2net_led_data = {
+ .num_leds = ARRAY_SIZE(d2net_leds),
+ .leds = d2net_leds,
+};
+
+static struct platform_device d2net_gpio_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &d2net_led_data,
+ },
+};
+
+static void __init d2net_gpio_leds_init(void)
+{
+ int err;
+
+ /* Configure register blink_ctrl to allow SATA activity LED blinking. */
+ err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink");
+ if (err == 0) {
+ err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1);
+ if (err)
+ gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL);
+ }
+ if (err)
+ pr_err("d2net: failed to configure blue LED blink GPIO\n");
+
+ platform_device_register(&d2net_gpio_leds);
+}
+
+/*****************************************************************************
+ * General Setup
+ ****************************************************************************/
+
+void __init d2net_init(void)
+{
+ d2net_gpio_leds_init();
+
+ pr_notice("d2net: Flash write are not yet supported.\n");
+}
+++ /dev/null
-/*
- * arch/arm/mach-orion5x/d2net-setup.c
- *
- * LaCie d2Network and Big Disk Network NAS setup
- *
- * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/leds.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/ata_platform.h>
-#include <linux/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/orion5x.h>
-#include <plat/orion-gpio.h>
-#include "common.h"
-#include "mpp.h"
-
-/*****************************************************************************
- * LaCie d2 Network Info
- ****************************************************************************/
-
-/*
- * 512KB NOR flash Device bus boot chip select
- */
-
-#define D2NET_NOR_BOOT_BASE 0xfff80000
-#define D2NET_NOR_BOOT_SIZE SZ_512K
-
-/*****************************************************************************
- * 512KB NOR Flash on Boot Device
- ****************************************************************************/
-
-/*
- * TODO: Check write support on flash MX29LV400CBTC-70G
- */
-
-static struct mtd_partition d2net_partitions[] = {
- {
- .name = "Full512kb",
- .size = MTDPART_SIZ_FULL,
- .offset = 0,
- .mask_flags = MTD_WRITEABLE,
- },
-};
-
-static struct physmap_flash_data d2net_nor_flash_data = {
- .width = 1,
- .parts = d2net_partitions,
- .nr_parts = ARRAY_SIZE(d2net_partitions),
-};
-
-static struct resource d2net_nor_flash_resource = {
- .flags = IORESOURCE_MEM,
- .start = D2NET_NOR_BOOT_BASE,
- .end = D2NET_NOR_BOOT_BASE
- + D2NET_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device d2net_nor_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &d2net_nor_flash_data,
- },
- .num_resources = 1,
- .resource = &d2net_nor_flash_resource,
-};
-
-/*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data d2net_eth_data = {
- .phy_addr = MV643XX_ETH_PHY_ADDR(8),
-};
-
-/*****************************************************************************
- * I2C devices
- ****************************************************************************/
-
-/*
- * i2c addr | chip | description
- * 0x32 | Ricoh 5C372b | RTC
- * 0x3e | GMT G762 | PWM fan controller
- * 0x50 | HT24LC08 | eeprom (1kB)
- *
- * TODO: Add G762 support to the g760a driver.
- */
-static struct i2c_board_info __initdata d2net_i2c_devices[] = {
- {
- I2C_BOARD_INFO("rs5c372b", 0x32),
- }, {
- I2C_BOARD_INFO("24c08", 0x50),
- },
-};
-
-/*****************************************************************************
- * SATA
- ****************************************************************************/
-
-static struct mv_sata_platform_data d2net_sata_data = {
- .n_ports = 2,
-};
-
-#define D2NET_GPIO_SATA0_POWER 3
-#define D2NET_GPIO_SATA1_POWER 12
-
-static void __init d2net_sata_power_init(void)
-{
- int err;
-
- err = gpio_request(D2NET_GPIO_SATA0_POWER, "SATA0 power");
- if (err == 0) {
- err = gpio_direction_output(D2NET_GPIO_SATA0_POWER, 1);
- if (err)
- gpio_free(D2NET_GPIO_SATA0_POWER);
- }
- if (err)
- pr_err("d2net: failed to configure SATA0 power GPIO\n");
-
- err = gpio_request(D2NET_GPIO_SATA1_POWER, "SATA1 power");
- if (err == 0) {
- err = gpio_direction_output(D2NET_GPIO_SATA1_POWER, 1);
- if (err)
- gpio_free(D2NET_GPIO_SATA1_POWER);
- }
- if (err)
- pr_err("d2net: failed to configure SATA1 power GPIO\n");
-}
-
-/*****************************************************************************
- * GPIO LED's
- ****************************************************************************/
-
-/*
- * The blue front LED is wired to the CPLD and can blink in relation with the
- * SATA activity.
- *
- * The following array detail the different LED registers and the combination
- * of their possible values:
- *
- * led_off | blink_ctrl | SATA active | LED state
- * | | |
- * 1 | x | x | off
- * 0 | 0 | 0 | off
- * 0 | 1 | 0 | blink (rate 300ms)
- * 0 | x | 1 | on
- *
- * Notes: The blue and the red front LED's can't be on at the same time.
- * Red LED have priority.
- */
-
-#define D2NET_GPIO_RED_LED 6
-#define D2NET_GPIO_BLUE_LED_BLINK_CTRL 16
-#define D2NET_GPIO_BLUE_LED_OFF 23
-
-static struct gpio_led d2net_leds[] = {
- {
- .name = "d2net:blue:sata",
- .default_trigger = "default-on",
- .gpio = D2NET_GPIO_BLUE_LED_OFF,
- .active_low = 1,
- },
- {
- .name = "d2net:red:fail",
- .gpio = D2NET_GPIO_RED_LED,
- },
-};
-
-static struct gpio_led_platform_data d2net_led_data = {
- .num_leds = ARRAY_SIZE(d2net_leds),
- .leds = d2net_leds,
-};
-
-static struct platform_device d2net_gpio_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &d2net_led_data,
- },
-};
-
-static void __init d2net_gpio_leds_init(void)
-{
- int err;
-
- /* Configure GPIO over MPP max number. */
- orion_gpio_set_valid(D2NET_GPIO_BLUE_LED_OFF, 1);
-
- /* Configure register blink_ctrl to allow SATA activity LED blinking. */
- err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink");
- if (err == 0) {
- err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1);
- if (err)
- gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL);
- }
- if (err)
- pr_err("d2net: failed to configure blue LED blink GPIO\n");
-
- platform_device_register(&d2net_gpio_leds);
-}
-
-/****************************************************************************
- * GPIO keys
- ****************************************************************************/
-
-#define D2NET_GPIO_PUSH_BUTTON 18
-#define D2NET_GPIO_POWER_SWITCH_ON 8
-#define D2NET_GPIO_POWER_SWITCH_OFF 9
-
-#define D2NET_SWITCH_POWER_ON 0x1
-#define D2NET_SWITCH_POWER_OFF 0x2
-
-static struct gpio_keys_button d2net_buttons[] = {
- {
- .type = EV_SW,
- .code = D2NET_SWITCH_POWER_OFF,
- .gpio = D2NET_GPIO_POWER_SWITCH_OFF,
- .desc = "Power rocker switch (auto|off)",
- .active_low = 0,
- },
- {
- .type = EV_SW,
- .code = D2NET_SWITCH_POWER_ON,
- .gpio = D2NET_GPIO_POWER_SWITCH_ON,
- .desc = "Power rocker switch (on|auto)",
- .active_low = 0,
- },
- {
- .type = EV_KEY,
- .code = KEY_POWER,
- .gpio = D2NET_GPIO_PUSH_BUTTON,
- .desc = "Front Push Button",
- .active_low = 0,
- },
-};
-
-static struct gpio_keys_platform_data d2net_button_data = {
- .buttons = d2net_buttons,
- .nbuttons = ARRAY_SIZE(d2net_buttons),
-};
-
-static struct platform_device d2net_gpio_buttons = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &d2net_button_data,
- },
-};
-
-/*****************************************************************************
- * General Setup
- ****************************************************************************/
-
-static unsigned int d2net_mpp_modes[] __initdata = {
- MPP0_GPIO, /* Board ID (bit 0) */
- MPP1_GPIO, /* Board ID (bit 1) */
- MPP2_GPIO, /* Board ID (bit 2) */
- MPP3_GPIO, /* SATA 0 power */
- MPP4_UNUSED,
- MPP5_GPIO, /* Fan fail detection */
- MPP6_GPIO, /* Red front LED */
- MPP7_UNUSED,
- MPP8_GPIO, /* Rear power switch (on|auto) */
- MPP9_GPIO, /* Rear power switch (auto|off) */
- MPP10_UNUSED,
- MPP11_UNUSED,
- MPP12_GPIO, /* SATA 1 power */
- MPP13_UNUSED,
- MPP14_SATA_LED, /* SATA 0 active */
- MPP15_SATA_LED, /* SATA 1 active */
- MPP16_GPIO, /* Blue front LED blink control */
- MPP17_UNUSED,
- MPP18_GPIO, /* Front button (0 = Released, 1 = Pushed ) */
- MPP19_UNUSED,
- 0,
- /* 22: USB port 1 fuse (0 = Fail, 1 = Ok) */
- /* 23: Blue front LED off */
- /* 24: Inhibit board power off (0 = Disabled, 1 = Enabled) */
-};
-
-#define D2NET_GPIO_INHIBIT_POWER_OFF 24
-
-static void __init d2net_init(void)
-{
- /*
- * Setup basic Orion functions. Need to be called early.
- */
- orion5x_init();
-
- orion5x_mpp_conf(d2net_mpp_modes);
-
- /*
- * Configure peripherals.
- */
- orion5x_ehci0_init();
- orion5x_eth_init(&d2net_eth_data);
- orion5x_i2c_init();
- orion5x_uart0_init();
-
- d2net_sata_power_init();
- orion5x_sata_init(&d2net_sata_data);
-
- mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
- ORION_MBUS_DEVBUS_BOOT_ATTR,
- D2NET_NOR_BOOT_BASE,
- D2NET_NOR_BOOT_SIZE);
- platform_device_register(&d2net_nor_flash);
-
- platform_device_register(&d2net_gpio_buttons);
-
- d2net_gpio_leds_init();
-
- pr_notice("d2net: Flash write are not yet supported.\n");
-
- i2c_register_board_info(0, d2net_i2c_devices,
- ARRAY_SIZE(d2net_i2c_devices));
-
- orion_gpio_set_valid(D2NET_GPIO_INHIBIT_POWER_OFF, 1);
-}
-
-/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
-
-#ifdef CONFIG_MACH_D2NET
-MACHINE_START(D2NET, "LaCie d2 Network")
- .atag_offset = 0x100,
- .init_machine = d2net_init,
- .map_io = orion5x_map_io,
- .init_early = orion5x_init_early,
- .init_irq = orion5x_init_irq,
- .init_time = orion5x_timer_init,
- .fixup = tag_fixup_mem32,
- .restart = orion5x_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_BIGDISK
-MACHINE_START(BIGDISK, "LaCie Big Disk Network")
- .atag_offset = 0x100,
- .init_machine = d2net_init,
- .map_io = orion5x_map_io,
- .init_early = orion5x_init_early,
- .init_irq = orion5x_init_irq,
- .init_time = orion5x_timer_init,
- .fixup = tag_fixup_mem32,
- .restart = orion5x_restart,
-MACHINE_END
-#endif
-
projects / openwrt / staging / blogic.git / commitdiff