#define DEFAULT_JUMBO 9234
-/* BM/HV Specific Registers */
-#define BM_PORT_CTRL_PAGE 769
-
-#define PHY_UPPER_SHIFT 21
-#define BM_PHY_REG(page, reg) \
- (((reg) & MAX_PHY_REG_ADDRESS) |\
- (((page) & 0xFFFF) << PHY_PAGE_SHIFT) |\
- (((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
-
-/* BM PHY Copper Specific Status */
-#define BM_CS_STATUS 17
-#define BM_CS_STATUS_LINK_UP 0x0400
-#define BM_CS_STATUS_RESOLVED 0x0800
-#define BM_CS_STATUS_SPEED_MASK 0xC000
-#define BM_CS_STATUS_SPEED_1000 0x8000
-
-/* 82577 Mobile Phy Status Register */
-#define HV_M_STATUS 26
-#define HV_M_STATUS_AUTONEG_COMPLETE 0x1000
-#define HV_M_STATUS_SPEED_MASK 0x0300
-#define HV_M_STATUS_SPEED_1000 0x0200
-#define HV_M_STATUS_LINK_UP 0x0040
-
/* Time to wait before putting the device into D3 if there's no link (in ms). */
#define LINK_TIMEOUT 100
extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
-extern s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw);
-extern s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw);
extern s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data);
-extern s32 e1000e_setup_copper_link(struct e1000_hw *hw);
-extern s32 e1000e_get_phy_id(struct e1000_hw *hw);
-extern s32 e1000e_check_reset_block_generic(struct e1000_hw *hw);
-extern s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
-extern s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
-extern s32 e1000e_get_phy_info_igp(struct e1000_hw *hw);
-extern s32 e1000_set_page_igp(struct e1000_hw *hw, u16 page);
-extern s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset,
- u16 *data);
-extern s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw);
-extern s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active);
-extern s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset,
- u16 data);
-extern s32 e1000e_phy_sw_reset(struct e1000_hw *hw);
-extern s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
-extern s32 e1000e_get_cfg_done_generic(struct e1000_hw *hw);
-extern s32 e1000e_get_cable_length_m88(struct e1000_hw *hw);
-extern s32 e1000e_get_phy_info_m88(struct e1000_hw *hw);
-extern s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw);
-extern enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id);
-extern s32 e1000e_determine_phy_address(struct e1000_hw *hw);
-extern s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000_enable_phy_wakeup_reg_access_bm(struct e1000_hw *hw,
- u16 *phy_reg);
-extern s32 e1000_disable_phy_wakeup_reg_access_bm(struct e1000_hw *hw,
- u16 *phy_reg);
-extern s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data);
-extern void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl);
-extern s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset,
- u16 data);
-extern s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset,
- u16 *data);
-extern s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
- u32 usec_interval, bool *success);
-extern s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
-extern void e1000_power_up_phy_copper(struct e1000_hw *hw);
-extern void e1000_power_down_phy_copper(struct e1000_hw *hw);
-extern s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000e_check_downshift(struct e1000_hw *hw);
-extern s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset,
- u16 *data);
-extern s32 e1000_read_phy_reg_page_hv(struct e1000_hw *hw, u32 offset,
- u16 *data);
-extern s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset,
- u16 data);
-extern s32 e1000_write_phy_reg_page_hv(struct e1000_hw *hw, u32 offset,
- u16 data);
-extern s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw);
-extern s32 e1000_copper_link_setup_82577(struct e1000_hw *hw);
-extern s32 e1000_check_polarity_82577(struct e1000_hw *hw);
-extern s32 e1000_get_phy_info_82577(struct e1000_hw *hw);
-extern s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw);
-extern s32 e1000_get_cable_length_82577(struct e1000_hw *hw);
-
-extern s32 e1000_check_polarity_m88(struct e1000_hw *hw);
-extern s32 e1000_get_phy_info_ife(struct e1000_hw *hw);
-extern s32 e1000_check_polarity_ife(struct e1000_hw *hw);
-extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
-extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
extern void e1000e_ptp_init(struct e1000_adapter *adapter);
extern void e1000e_ptp_remove(struct e1000_adapter *adapter);
E1000_RXUDP = 0x0B638, /* Timesync Rx UDP Port - RW */
};
-#define E1000_MAX_PHY_ADDR 4
-
-/* IGP01E1000 Specific Registers */
-#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* Port Config */
-#define IGP01E1000_PHY_PORT_STATUS 0x11 /* Status */
-#define IGP01E1000_PHY_PORT_CTRL 0x12 /* Control */
-#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health */
-#define IGP02E1000_PHY_POWER_MGMT 0x19 /* Power Management */
-#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* Page Select */
-#define BM_PHY_PAGE_SELECT 22 /* Page Select for BM */
-#define IGP_PAGE_SHIFT 5
-#define PHY_REG_MASK 0x1F
-
-#define BM_WUC_PAGE 800
-#define BM_WUC_ADDRESS_OPCODE 0x11
-#define BM_WUC_DATA_OPCODE 0x12
-#define BM_WUC_ENABLE_PAGE 769
-#define BM_WUC_ENABLE_REG 17
-#define BM_WUC_ENABLE_BIT (1 << 2)
-#define BM_WUC_HOST_WU_BIT (1 << 4)
-#define BM_WUC_ME_WU_BIT (1 << 5)
-
-#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4
-#define IGP01E1000_PHY_POLARITY_MASK 0x0078
-
-#define IGP01E1000_PSCR_AUTO_MDIX 0x1000
-#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0=MDI, 1=MDIX */
-
-#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
-
-#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */
-#define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */
-#define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */
-
-#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000
-
-#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002
-#define IGP01E1000_PSSR_MDIX 0x0800
-#define IGP01E1000_PSSR_SPEED_MASK 0xC000
-#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000
-
-#define IGP02E1000_PHY_CHANNEL_NUM 4
-#define IGP02E1000_PHY_AGC_A 0x11B1
-#define IGP02E1000_PHY_AGC_B 0x12B1
-#define IGP02E1000_PHY_AGC_C 0x14B1
-#define IGP02E1000_PHY_AGC_D 0x18B1
-
-#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Course - 15:13, Fine - 12:9 */
-#define IGP02E1000_AGC_LENGTH_MASK 0x7F
-#define IGP02E1000_AGC_RANGE 15
-
/* manage.c */
#define E1000_VFTA_ENTRY_SHIFT 5
#define E1000_VFTA_ENTRY_MASK 0x7F
/* nvm.c */
#define E1000_STM_OPCODE 0xDB00
-#define E1000_KMRNCTRLSTA_OFFSET 0x001F0000
-#define E1000_KMRNCTRLSTA_OFFSET_SHIFT 16
-#define E1000_KMRNCTRLSTA_REN 0x00200000
-#define E1000_KMRNCTRLSTA_CTRL_OFFSET 0x1 /* Kumeran Control */
-#define E1000_KMRNCTRLSTA_DIAG_OFFSET 0x3 /* Kumeran Diagnostic */
-#define E1000_KMRNCTRLSTA_TIMEOUTS 0x4 /* Kumeran Timeouts */
-#define E1000_KMRNCTRLSTA_INBAND_PARAM 0x9 /* Kumeran InBand Parameters */
-#define E1000_KMRNCTRLSTA_IBIST_DISABLE 0x0200 /* Kumeran IBIST Disable */
-#define E1000_KMRNCTRLSTA_DIAG_NELPBK 0x1000 /* Nearend Loopback mode */
-#define E1000_KMRNCTRLSTA_K1_CONFIG 0x7
-#define E1000_KMRNCTRLSTA_K1_ENABLE 0x0002
-#define E1000_KMRNCTRLSTA_HD_CTRL 0x10 /* Kumeran HD Control */
-
-#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10
-#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY Special Control */
-#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY Special and LED Control */
-#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control */
-
-/* IFE PHY Extended Status Control */
-#define IFE_PESC_POLARITY_REVERSED 0x0100
-
-/* IFE PHY Special Control */
-#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010
-#define IFE_PSC_FORCE_POLARITY 0x0020
-
-/* IFE PHY Special Control and LED Control */
-#define IFE_PSCL_PROBE_MODE 0x0020
-#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */
-#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
-
-/* IFE PHY MDIX Control */
-#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
-#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDI-X, 0=force MDI */
-#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable auto MDI/MDI-X, 0=disable */
-
-#define E1000_CABLE_LENGTH_UNDEFINED 0xFF
-
#define E1000_DEV_ID_82571EB_COPPER 0x105E
#define E1000_DEV_ID_82571EB_FIBER 0x105F
#define E1000_DEV_ID_82571EB_SERDES 0x1060
};
#include "mac.h"
+#include "phy.h"
/* Function pointers for the MAC. */
struct e1000_mac_operations {
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2013 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_PHY_H_
+#define _E1000E_PHY_H_
+
+s32 e1000e_check_downshift(struct e1000_hw *hw);
+s32 e1000_check_polarity_m88(struct e1000_hw *hw);
+s32 e1000_check_polarity_igp(struct e1000_hw *hw);
+s32 e1000_check_polarity_ife(struct e1000_hw *hw);
+s32 e1000e_check_reset_block_generic(struct e1000_hw *hw);
+s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw);
+s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw);
+s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
+s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
+s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
+s32 e1000e_get_cable_length_m88(struct e1000_hw *hw);
+s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
+s32 e1000e_get_cfg_done_generic(struct e1000_hw *hw);
+s32 e1000e_get_phy_id(struct e1000_hw *hw);
+s32 e1000e_get_phy_info_igp(struct e1000_hw *hw);
+s32 e1000e_get_phy_info_m88(struct e1000_hw *hw);
+s32 e1000_get_phy_info_ife(struct e1000_hw *hw);
+s32 e1000e_phy_sw_reset(struct e1000_hw *hw);
+void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl);
+s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw);
+s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
+s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000_set_page_igp(struct e1000_hw *hw, u16 page);
+s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active);
+s32 e1000e_setup_copper_link(struct e1000_hw *hw);
+s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
+ u32 usec_interval, bool *success);
+s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw);
+enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id);
+s32 e1000e_determine_phy_address(struct e1000_hw *hw);
+s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000_enable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg);
+s32 e1000_disable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg);
+s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data);
+void e1000_power_up_phy_copper(struct e1000_hw *hw);
+void e1000_power_down_phy_copper(struct e1000_hw *hw);
+s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000_read_phy_reg_page_hv(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000_write_phy_reg_page_hv(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw);
+s32 e1000_copper_link_setup_82577(struct e1000_hw *hw);
+s32 e1000_check_polarity_82577(struct e1000_hw *hw);
+s32 e1000_get_phy_info_82577(struct e1000_hw *hw);
+s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw);
+s32 e1000_get_cable_length_82577(struct e1000_hw *hw);
+
+#define E1000_MAX_PHY_ADDR 8
+
+/* IGP01E1000 Specific Registers */
+#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* Port Config */
+#define IGP01E1000_PHY_PORT_STATUS 0x11 /* Status */
+#define IGP01E1000_PHY_PORT_CTRL 0x12 /* Control */
+#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health */
+#define IGP02E1000_PHY_POWER_MGMT 0x19 /* Power Management */
+#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* Page Select */
+#define BM_PHY_PAGE_SELECT 22 /* Page Select for BM */
+#define IGP_PAGE_SHIFT 5
+#define PHY_REG_MASK 0x1F
+
+/* BM/HV Specific Registers */
+#define BM_PORT_CTRL_PAGE 769
+#define BM_WUC_PAGE 800
+#define BM_WUC_ADDRESS_OPCODE 0x11
+#define BM_WUC_DATA_OPCODE 0x12
+#define BM_WUC_ENABLE_PAGE BM_PORT_CTRL_PAGE
+#define BM_WUC_ENABLE_REG 17
+#define BM_WUC_ENABLE_BIT (1 << 2)
+#define BM_WUC_HOST_WU_BIT (1 << 4)
+#define BM_WUC_ME_WU_BIT (1 << 5)
+
+#define PHY_UPPER_SHIFT 21
+#define BM_PHY_REG(page, reg) \
+ (((reg) & MAX_PHY_REG_ADDRESS) |\
+ (((page) & 0xFFFF) << PHY_PAGE_SHIFT) |\
+ (((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
+#define BM_PHY_REG_PAGE(offset) \
+ ((u16)(((offset) >> PHY_PAGE_SHIFT) & 0xFFFF))
+#define BM_PHY_REG_NUM(offset) \
+ ((u16)(((offset) & MAX_PHY_REG_ADDRESS) |\
+ (((offset) >> (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)) &\
+ ~MAX_PHY_REG_ADDRESS)))
+
+#define HV_INTC_FC_PAGE_START 768
+#define I82578_ADDR_REG 29
+#define I82577_ADDR_REG 16
+#define I82577_CFG_REG 22
+#define I82577_CFG_ASSERT_CRS_ON_TX (1 << 15)
+#define I82577_CFG_ENABLE_DOWNSHIFT (3 << 10) /* auto downshift */
+#define I82577_CTRL_REG 23
+
+/* 82577 specific PHY registers */
+#define I82577_PHY_CTRL_2 18
+#define I82577_PHY_LBK_CTRL 19
+#define I82577_PHY_STATUS_2 26
+#define I82577_PHY_DIAG_STATUS 31
+
+/* I82577 PHY Status 2 */
+#define I82577_PHY_STATUS2_REV_POLARITY 0x0400
+#define I82577_PHY_STATUS2_MDIX 0x0800
+#define I82577_PHY_STATUS2_SPEED_MASK 0x0300
+#define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200
+
+/* I82577 PHY Control 2 */
+#define I82577_PHY_CTRL2_MANUAL_MDIX 0x0200
+#define I82577_PHY_CTRL2_AUTO_MDI_MDIX 0x0400
+#define I82577_PHY_CTRL2_MDIX_CFG_MASK 0x0600
+
+/* I82577 PHY Diagnostics Status */
+#define I82577_DSTATUS_CABLE_LENGTH 0x03FC
+#define I82577_DSTATUS_CABLE_LENGTH_SHIFT 2
+
+/* BM PHY Copper Specific Control 1 */
+#define BM_CS_CTRL1 16
+
+/* BM PHY Copper Specific Status */
+#define BM_CS_STATUS 17
+#define BM_CS_STATUS_LINK_UP 0x0400
+#define BM_CS_STATUS_RESOLVED 0x0800
+#define BM_CS_STATUS_SPEED_MASK 0xC000
+#define BM_CS_STATUS_SPEED_1000 0x8000
+
+/* 82577 Mobile Phy Status Register */
+#define HV_M_STATUS 26
+#define HV_M_STATUS_AUTONEG_COMPLETE 0x1000
+#define HV_M_STATUS_SPEED_MASK 0x0300
+#define HV_M_STATUS_SPEED_1000 0x0200
+#define HV_M_STATUS_LINK_UP 0x0040
+
+#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4
+#define IGP01E1000_PHY_POLARITY_MASK 0x0078
+
+#define IGP01E1000_PSCR_AUTO_MDIX 0x1000
+#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0=MDI, 1=MDIX */
+
+#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
+
+#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */
+#define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */
+#define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */
+
+#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000
+
+#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002
+#define IGP01E1000_PSSR_MDIX 0x0800
+#define IGP01E1000_PSSR_SPEED_MASK 0xC000
+#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000
+
+#define IGP02E1000_PHY_CHANNEL_NUM 4
+#define IGP02E1000_PHY_AGC_A 0x11B1
+#define IGP02E1000_PHY_AGC_B 0x12B1
+#define IGP02E1000_PHY_AGC_C 0x14B1
+#define IGP02E1000_PHY_AGC_D 0x18B1
+
+#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Course=15:13, Fine=12:9 */
+#define IGP02E1000_AGC_LENGTH_MASK 0x7F
+#define IGP02E1000_AGC_RANGE 15
+
+#define E1000_CABLE_LENGTH_UNDEFINED 0xFF
+
+#define E1000_KMRNCTRLSTA_OFFSET 0x001F0000
+#define E1000_KMRNCTRLSTA_OFFSET_SHIFT 16
+#define E1000_KMRNCTRLSTA_REN 0x00200000
+#define E1000_KMRNCTRLSTA_CTRL_OFFSET 0x1 /* Kumeran Control */
+#define E1000_KMRNCTRLSTA_DIAG_OFFSET 0x3 /* Kumeran Diagnostic */
+#define E1000_KMRNCTRLSTA_TIMEOUTS 0x4 /* Kumeran Timeouts */
+#define E1000_KMRNCTRLSTA_INBAND_PARAM 0x9 /* Kumeran InBand Parameters */
+#define E1000_KMRNCTRLSTA_IBIST_DISABLE 0x0200 /* Kumeran IBIST Disable */
+#define E1000_KMRNCTRLSTA_DIAG_NELPBK 0x1000 /* Nearend Loopback mode */
+#define E1000_KMRNCTRLSTA_K1_CONFIG 0x7
+#define E1000_KMRNCTRLSTA_K1_ENABLE 0x0002 /* enable K1 */
+#define E1000_KMRNCTRLSTA_HD_CTRL 0x10 /* Kumeran HD Control */
+
+#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10
+#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY Special Ctrl */
+#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY Special and LED Ctrl */
+#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control */
+
+/* IFE PHY Extended Status Control */
+#define IFE_PESC_POLARITY_REVERSED 0x0100
+
+/* IFE PHY Special Control */
+#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010
+#define IFE_PSC_FORCE_POLARITY 0x0020
+
+/* IFE PHY Special Control and LED Control */
+#define IFE_PSCL_PROBE_MODE 0x0020
+#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */
+#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
+
+/* IFE PHY MDIX Control */
+#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
+#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDI-X, 0=force MDI */
+#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable auto, 0=disable */
+
+#endif
projects / openwrt / staging / blogic.git / commitdiff