board=$(board_name)
case "$board" in
- traverse,ls1043v|\
- traverse,ls1043s)
- ubootenv_add_uci_config "/dev/mtd1" "0x40000" "0x2000" "0x20000"
- ;;
traverse,ten64)
ubootenv_add_uci_config "/dev/mtd3" "0x0000" "0x80000" "0x80000"
;;
board=$(board_name)
case "$board" in
-traverse,ls1043v)
- ucidef_set_led_netdev "wan" "WAN LED" "ls1043v:yellow:wan" "eth4"
- ;;
-traverse,ls1043s)
- ucidef_set_led_netdev "wan" "WAN LED" "ls1043s:yellow:wan" "eth4"
- ucidef_set_led_netdev "xgact" "10G Activity" "ls1043s:yellow:10gact" "eth6"
- ucidef_set_led_netdev "xglink" "10G Link" "ls1043s:green:10glink" "eth6"
- ;;
traverse,ten64)
ucidef_set_led_netdev "sfp1" "SFP 1" "ten64:green:sfp1:down" "eth8" "link tx rx"
ucidef_set_led_netdev "sfp2" "SFP 2" "ten64:green:sfp2:up" "eth9" "link tx rx"
fsl,ls1028a-rdb-sdboot)
ucidef_set_interfaces_lan_wan "swp0 swp1 swp2 swp3" "eth0"
;;
- traverse,ls1043v)
- ucidef_set_interface_lan "eth0 eth1 eth2 eth3"
- ucidef_set_interface_wan "eth4"
- ;;
- traverse,ls1043s)
- ucidef_set_interface_lan "eth0 eth1 eth2 eth3 eth6"
- ucidef_set_interface_wan "eth4"
- ;;
traverse,ten64)
ucidef_set_interface_lan "eth0 eth1 eth2 eth3"
ucidef_set_interface_wan "eth6"
board=$(board_name)
case "$board" in
-traverse,ls1043v)
- ucidef_add_gpio_switch "lte_reset" "LTE Reset" "377"
- ucidef_add_gpio_switch "lte_disable" "LTE Airplane mode" "378"
- ;;
-traverse,ls1043s)
- ucidef_add_gpio_switch "tensfp_txdisable" "SFP+ TX Disable" "378"
- ucidef_add_gpio_switch "gigsfp_txdisable" "SFP TX Disable" "381"
- ucidef_add_gpio_switch "lte_reset" "LTE Reset" "502"
- ucidef_add_gpio_switch "lte_disable" "LTE Airplane Mode" "394"
- ucidef_add_gpio_switch "lte_power" "LTE Power" "395"
- ;;
traverse,ten64)
ucidef_add_gpio_switch "lte_reset" "Cell Modem Reset" "376"
ucidef_add_gpio_switch "lte_power" "Cell Modem Power" "377"
+++ /dev/null
-reorder_layerscape_interfaces() {
- if [ ! -f /tmp/sysinfo/board_name ]; then
- echo "No board name found, not doing reorder_layerscape_interfaces"
- return 0
- fi
-
- board=$(cat /tmp/sysinfo/board_name)
- case "$board" in
- traverse,ls1043v|\
- traverse,ls1043s)
-
- # Reorder ethernet interfaces to match the physical order
- ip link set eth2 name fm1-mac3
- ip link set eth4 name eth2
- ip link set eth3 name fm1-mac4
- ip link set eth5 name eth3
- ip link set fm1-mac3 name eth4
- ip link set fm1-mac4 name eth5
- ;;
- default)
- echo "Unknown board $board"
- ;;
- esac
-}
-
-boot_hook_add preinit_main reorder_layerscape_interfaces
echo "Writing rootfs..."
tar xf $tar_file ${board_dir}/root -O | dd of=/dev/mmcblk0p2 bs=512k > /dev/null 2>&1
-}
-platform_do_upgrade_traverse_nandubi() {
- bootsys=$(fw_printenv bootsys | awk -F= '{{print $2}}')
- newbootsys=2
- if [ "$bootsys" -eq "2" ]; then
- newbootsys=1
- fi
-
- # If nand_do_upgrade succeeds, we don't have an opportunity to add any actions of
- # our own, so do it here and set back on failure
- echo "Setting bootsys to #${newbootsys}"
- fw_setenv bootsys $newbootsys
- CI_UBIPART="nandubi"
- CI_KERNPART="kernel${newbootsys}"
- CI_ROOTPART="rootfs${newbootsys}"
- nand_do_upgrade "$1" || (echo "Upgrade failed, setting bootsys ${bootsys}" && fw_setenv bootsys $bootsys)
-
}
platform_do_upgrade_traverse_slotubi() {
local board=$(board_name)
case "$board" in
- traverse,ls1043v | \
- traverse,ls1043s)
- nand_do_platform_check "traverse-ls1043" $1
- return $?
- ;;
traverse,ten64)
nand_do_platform_check "ten64-mtd" $1
return $?
touch /var/lock/fw_printenv.lock
case "$board" in
- traverse,ls1043v | \
- traverse,ls1043s)
- platform_do_upgrade_traverse_nandubi "$1"
- ;;
traverse,ten64)
platform_do_upgrade_traverse_slotubi "${1}"
;;
+++ /dev/null
-/*
- * Device Tree Include file for Traverse LS1043S board.
- *
- * Copyright 2014-2015, Freescale Semiconductor
- * Copyright 2017-2018, Traverse Technologies
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPLv2 or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This library is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This library is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "fsl-ls1043a.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Traverse LS1043S";
- compatible = "traverse,ls1043s";
-
- aliases {
- crypto = &crypto;
- ethernet0 = &EMAC0;
- ethernet1 = &EMAC1;
- ethernet2 = &EMAC2;
- ethernet3 = &EMAC3;
- ethernet4 = &EMAC4;
- ethernet5 = &EMAC5;
- };
-
- leds {
- compatible = "gpio-leds";
- gpio0 {
- label = "ls1043s:green:user0";
- gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
- };
- gpio1 {
- label = "ls1043s:green:user1";
- gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
- };
- /* LED D17 */
- gpio2 {
- label = "ls1043s:green:wan";
- gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
- };
- gpio3 {
- label = "ls1043s:yellow:wan";
- gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
- };
- /* LED D18 */
- gpio4 {
- label = "ls1043s:green:mgmt";
- gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
- };
- gpio5 {
- label = "ls1043s:yellow:mgmt";
- gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
- };
- /* LED D6 */
- gpio6 {
- label = "ls1043s:green:user2";
- gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
- };
-
- /* SFP+ LEDs - these are for chassis
- * with lightpipes only
- */
- teng_act {
- label = "ls1043s:yellow:10gact";
- gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
- };
-
- teng_link {
- label = "ls1043s:green:10glink";
- gpios = <&gpio4 1 GPIO_ACTIVE_LOW>;
- };
- };
-
- keys {
- compatible = "gpio-keys-polled";
- #address-cells = <1>;
- #size-cells = <0>;
- poll-interval = <1000>;
- /* This button may not be loaded on all boards */
- button@0 {
- label = "Front button";
- linux,code = <KEY_SETUP>;
- gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- };
- /* This is wired to header S3 */
- button@1 {
- label = "Rear button";
- linux,code = <KEY_WPS_BUTTON>;
- gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- };
- };
-};
-
-&esdhc {
- mmc-hs200-1_8v;
- sd-uhs-sdr104;
- sd-uhs-sdr50;
- sd-uhs-sdr25;
- sd-uhs-sdr12;
-};
-
-&i2c0 {
- status = "okay";
- rtc@6f {
- compatible = "intersil,isl1208";
- reg = <0x6f>;
- };
-
- sfp_pca9534: pca9534@24 {
- compatible = "ti,tca9534", "nxp,pca9534";
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x24>;
- gpio-base = <100>;
- };
-
- controller@50 {
- compatible = "traverse,controller";
- reg = <0x50>;
- };
-
- ds125df111@18 {
- compatible = "ti,ds125df111";
- reg = <0x18>;
- };
-
- emc1704@4c {
- compatible = "microchip,emc1704";
- reg = <0x4c>;
- };
-
- pac1934@16 {
- compatible = "microchip,pac1934";
- reg = <0x16>;
- /* Monitoring 3.3V, 5V, Vin/12V (voltage only), Vbat/RTC (voltage only) */
- shunt-resistors = <4000 12000 0 0>;
- };
-
- pmic@8 {
- compatible = "freescale,mc34vr500";
- reg = <0x08>;
- };
-};
-
-/* I2C Bus for SFP EEPROM and control
- * These are multiplexed so
- * they don't collide when loaded
- */
-&i2c3 {
- status = "okay";
- i2c-switch@70 {
- compatible = "nxp,pca9540";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x70>;
-
- gigsfp_i2c: i2c@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
- };
- tensfp_i2c: i2c@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
- };
- };
-};
-
-&ifc {
- status = "okay";
- #address-cells = <2>;
- #size-cells = <1>;
- /* Only NAND flash is used on this board */
- ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>;
-
- nand@1,0 {
- compatible = "fsl,ifc-nand";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x0 0x0 0x10000>;
- };
-};
-
-&duart0 {
- status = "okay";
-};
-
-&duart1 {
- status = "okay";
-};
-
-#include "fsl-ls1043-post.dtsi"
-
-&fman0 {
- EMAC0: ethernet@e0000 {
- phy-handle = <&qsgmii_phy1>;
- phy-connection-type = "qsgmii";
- local-mac-address = [0A 00 00 00 00 01];
- };
-
- EMAC1: ethernet@e2000 {
- phy-handle = <&qsgmii_phy2>;
- phy-connection-type = "qsgmii";
- local-mac-address = [0A 00 00 00 00 02];
- };
-
- EMAC2: ethernet@e8000 {
- phy-handle = <&qsgmii_phy3>;
- phy-connection-type = "qsgmii";
- local-mac-address = [0A 00 00 00 00 03];
- };
-
- EMAC3: ethernet@ea000 {
- phy-handle = <&qsgmii_phy4>;
- phy-connection-type = "qsgmii";
- local-mac-address = [0A 00 00 00 00 04];
- };
-
- /* SFP via AR8031
- * We treat this as a fixed-link as the
- * AR8031 is hard-configured into
- * 1000BASE-X mode
- * Should MII control be desired, remove
- * fixed-link and add
- * phy-handle = <&rgmii_phy1>;
- */
- EMAC4: ethernet@e4000 {
- phy-connection-type = "rgmii";
- local-mac-address = [0A 00 00 00 00 05];
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- /* Connection to Expansion (M.2) slot
- * Future WAN (i.e xDSL) plugin
- */
- EMAC5: ethernet@e6000 {
- phy-connection-type = "rgmii-id";
- local-mac-address = [00 00 00 00 00 06];
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- /* 10G SFP+ interface
- * This can also run at 1.25 and 2.5G with
- * the appropriate SerDes protocol setting in RCW
- */
- TENSFP: ethernet@f0000 {
- status = "okay";
- phy-connection-type = "xgmii";
- fixed-link {
- speed = <10000>;
- full-duplex;
- };
- };
-
- mdio@fc000 {
- rgmii_phy1: ethernet-phy@2 {
- reg = <0x2>;
- };
- qsgmii_phy1: ethernet-phy@4 {
- reg = <0x4>;
- };
- qsgmii_phy2: ethernet-phy@5 {
- reg = <0x5>;
- };
- qsgmii_phy3: ethernet-phy@6 {
- reg = <0x6>;
- };
- qsgmii_phy4: ethernet-phy@7 {
- reg = <0x7>;
- };
- };
-};
-
-/* No QUICC engine functions on this board -
- * pins are used for other functions (GPIO, I2C etc.)
- */
-&uqe {
- status = "disabled";
-};
-
-/* LS1043S does not use the QorIQ AHCI
- * controller.
- */
-&sata {
- status = "disabled";
-};
+++ /dev/null
-/*
- * Device Tree Include file for Traverse LS1043V board.
- *
- * Copyright 2014-2015, Freescale Semiconductor
- * Copyright 2017, Traverse Technologies
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPLv2 or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This library is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This library is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "fsl-ls1043a.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Traverse LS1043V";
- compatible = "traverse,ls1043v";
-
- aliases {
- crypto = &crypto;
- ethernet0 = &EMAC0;
- ethernet1 = &EMAC1;
- ethernet2 = &EMAC2;
- ethernet3 = &EMAC3;
- ethernet4 = &EMAC4;
- ethernet5 = &EMAC5;
- pca9555 = &pca9555;
- };
-
- leds {
- compatible = "gpio-leds";
- gpio0 {
- label = "ls1043v:green:user0";
- gpios = <&pca9555 0 GPIO_ACTIVE_LOW>;
- };
- gpio1 {
- label = "ls1043v:yellow:user0";
- gpios = <&pca9555 1 GPIO_ACTIVE_LOW>;
- };
- gpio2 {
- label = "ls1043v:green:user1";
- gpios = <&pca9555 2 GPIO_ACTIVE_LOW>;
- };
- gpio3 {
- label = "ls1043v:yellow:user1";
- gpios = <&pca9555 3 GPIO_ACTIVE_LOW>;
- };
- gpio4 {
- label = "ls1043v:green:user2";
- gpios = <&pca9555 4 GPIO_ACTIVE_HIGH>;
- };
- gpio5 {
- label = "ls1043v:yellow:wlan";
- gpios = <&pca9555 5 GPIO_ACTIVE_HIGH>;
- };
- gpio6 {
- label = "ls1043v:yellow:wan";
- gpios = <&pca9555 6 GPIO_ACTIVE_HIGH>;
- };
- };
-
- keys {
- compatible = "gpio-keys-polled";
- #address-cells = <1>;
- #size-cells = <0>;
- poll-interval = <1000>;
- button@0 {
- label = "Front button";
- linux,code = <KEY_SETUP>;
- gpios = <&pca9555 14 GPIO_ACTIVE_LOW>;
- };
- button@1 {
- label = "Rear button";
- linux,code = <KEY_WPS_BUTTON>;
- gpios = <&pca9555 15 GPIO_ACTIVE_LOW>;
- };
- };
-};
-
-&i2c0 {
- status = "okay";
- rtc@6f {
- compatible = "intersil,isl1208";
- reg = <0x6f>;
- };
-
- pca9555: pca9555@20 {
- compatible = "nxp,pca9555";
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x20>;
- gpio-base = <0>;
- };
-
- /* CPU core temp sensor and VDD (1.0V) sensor */
- ltc2990@4c {
- compatible = "lltc,ltc2990";
- reg = <0x4C>;
- lltc,meas-mode = <4 3>;
- };
-
- /* 3.3V and 5V monitor (may not be loaded on some SKUs) */
- ltc2990@4f {
- compatible = "lltc,ltc2990";
- reg = <0x4F>;
- lltc,meas-mode = <6 3>;
- };
-};
-
-&ifc {
- status = "okay";
- #address-cells = <2>;
- #size-cells = <1>;
- /* Only NAND flash is used on this board */
- ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>;
-
- nand@1,0 {
- compatible = "fsl,ifc-nand";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x0 0x0 0x10000>;
- };
-};
-
-&duart0 {
- status = "okay";
-};
-
-&duart1 {
- status = "okay";
-};
-
-#include "fsl-ls1043-post.dtsi"
-
-&fman0 {
- EMAC0: ethernet@e0000 {
- phy-handle = <&qsgmii_phy1>;
- phy-connection-type = "qsgmii";
- local-mac-address = [0A 00 00 00 00 01];
- };
-
- EMAC1: ethernet@e2000 {
- phy-handle = <&qsgmii_phy2>;
- phy-connection-type = "qsgmii";
- local-mac-address = [0A 00 00 00 00 02];
- };
-
- EMAC2: ethernet@e8000 {
- phy-handle = <&qsgmii_phy3>;
- phy-connection-type = "qsgmii";
- local-mac-address = [0A 00 00 00 00 03];
- };
-
- EMAC3: ethernet@ea000 {
- phy-handle = <&qsgmii_phy4>;
- phy-connection-type = "qsgmii";
- local-mac-address = [0A 00 00 00 00 04];
- };
- EMAC4: ethernet@e4000 {
- phy-handle = <&rgmii_phy1>;
- phy-connection-type = "rgmii";
- local-mac-address = [0A 00 00 00 00 05];
- };
-
- /* Connection to VDSL SoC */
- EMAC5: ethernet@e6000 {
- phy-connection-type = "rgmii-id";
- local-mac-address = [00 00 00 00 00 06];
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- /* 10G XFI interface - not in use on this platform */
- TENSFP: ethernet@f0000 {
- status = "disabled";
-
- phy-connection-type = "sgmii";
- fixed-link {
- /* NB: speed = 1000 and sgmii allows forward compatibility
- * with both 1G and 10G, the same is not true
- * in the reverse.
- */
- speed = <1000>;
- full-duplex;
- };
- };
-
- mdio@fc000 {
- rgmii_phy1: ethernet-phy@3 {
- reg = <0x3>;
- };
- qsgmii_phy1: ethernet-phy@4 {
- reg = <0x4>;
- };
- qsgmii_phy2: ethernet-phy@5 {
- reg = <0x5>;
- };
- qsgmii_phy3: ethernet-phy@6 {
- reg = <0x6>;
- };
- qsgmii_phy4: ethernet-phy@7 {
- reg = <0x7>;
- };
- };
-};
-
-/* No QUICC engine functions on this board */
-&uqe {
- status = "disabled";
-};
-
-/* No SATA/AHCI on this board */
-&sata {
- status = "disabled";
-};
dd if=$(STAGING_DIR_IMAGE)/$(1)-sdcard-head.img >> $@
endef
-define Build/traverse-fit
- ./mkits-multiple-config.sh -o $@.its -A $(LINUX_KARCH) \
- -v $(LINUX_VERSION) -k $@ -a $(KERNEL_LOADADDR) \
- -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
- -C gzip -c 1 -c 2 \
- -d $(DEVICE_DTS_DIR)/freescale/traverse-ls1043s.dtb \
- -D "Traverse_LS1043S" -n "ls1043s" -a $(FDT_LOADADDR) -c 1 \
- -d $(DEVICE_DTS_DIR)/freescale/traverse-ls1043v.dtb \
- -D "Traverse_LS1043V" -n "ls1043v" -a $(FDT_LOADADDR) -c 2
- PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
- @mv -f $@.new $@
-endef
-
define Build/traverse-fit-ls1088
./mkits-multiple-config.sh -o $@.its -A $(LINUX_KARCH) \
-v $(LINUX_VERSION) -k $@ -a $(KERNEL_LOADADDR) \
endef
TARGET_DEVICES += fsl_lx2160a-rdb-sdboot
-define Device/traverse_ls1043
- DEVICE_VENDOR := Traverse
- DEVICE_MODEL := LS1043 Boards
- KERNEL_NAME := Image
- KERNEL_SUFFIX := -kernel.itb
- KERNEL_INSTALL := 1
- FDT_LOADADDR = 0x90000000
- FILESYSTEMS := ubifs
- MKUBIFS_OPTS := -m 1 -e 262016 -c 128
- DEVICE_PACKAGES += \
- layerscape-fman \
- uboot-envtools \
- kmod-i2c-mux-pca954x \
- kmod-hwmon-core \
- kmod-gpio-pca953x kmod-input-gpio-keys-polled \
- kmod-rtc-isl1208
- DEVICE_DESCRIPTION = \
- Build images for Traverse LS1043 boards. This generates a single image \
- capable of booting on any of the boards in this family.
- DEVICE_DTS = freescale/traverse-ls1043s
- DEVICE_DTS_DIR = $(LINUX_DIR)/arch/arm64/boot/dts
- DEVICE_DTS_CONFIG = ls1043s
- KERNEL := kernel-bin | gzip | traverse-fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
- KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
- IMAGES = root sysupgrade.bin
- IMAGE/root = append-rootfs
- IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
- MKUBIFS_OPTS := -m 2048 -e 124KiB -c 4096
- SUPPORTED_DEVICES := traverse,ls1043s traverse,ls1043v
-endef
-TARGET_DEVICES += traverse_ls1043
-
define Device/traverse_ten64_mtd
DEVICE_VENDOR := Traverse
DEVICE_MODEL := Ten64 (NAND boot)
+++ /dev/null
-From 5b35aae22b4ca2400e49561c9267aa01346f91d4 Mon Sep 17 00:00:00 2001
-From: Mathew McBride <matt@traverse.com.au>
-Date: Tue, 17 Apr 2018 10:01:03 +1000
-Subject: [PATCH] add DTS for Traverse LS1043 Boards
-
-Signed-off-by: Mathew McBride <matt@traverse.com.au>
-[rebase]
-Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
----
- arch/arm64/boot/dts/freescale/Makefile | 3 +++
- arch/arm64/boot/dts/freescale/traverse-ls1043s.dts | 29 ++++++++++++++++++++++
- arch/arm64/boot/dts/freescale/traverse-ls1043v.dts | 29 ++++++++++++++++++++++
- 3 files changed, 61 insertions(+)
-
---- a/arch/arm64/boot/dts/freescale/Makefile
-+++ b/arch/arm64/boot/dts/freescale/Makefile
-@@ -31,6 +31,9 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2
- dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
- dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2162a-qds.dtb
-
-+dtb-$(CONFIG_ARCH_LAYERSCAPE) += traverse-ls1043v.dtb
-+dtb-$(CONFIG_ARCH_LAYERSCAPE) += traverse-ls1043s.dtb
-+
- dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
- dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
- dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
projects / openwrt / staging / dangole.git / commitdiff