[PATCH] ahci: do not powerdown during initialization

ahci_init_controller() calls ahci_deinit_port() to make sure the
controller is stopped before initializing the controller.  In turn,
ahci_deinit_port() invokes ahci_power_down() to power down the port.
If the controller supports slumber mode, the link is put into it.

Unfortunately, some devices don't implement link powersaving mode
properly and show erratic behavior after link is put into slumber
mode.  For example, HL-DT-ST DVD-RAM GSA-H30N completely locks up on
slumber transition and can only be recovered with the *REAL* hard
reset - power removal and reapply.

Note that this makes the first probing reset different from all
others.  If the above dvd-ram is hotplugged after ahci is initialized,
no problem occurs because ahci is already fully initialized with phy
powered up.  So, this might also be the reason for other weird AHCI
initial probing abnormalities.

This patch moves power up/down out of port init/deinit and call them
only when needed.

Power down is now called only when suspending.  As system suspend
usually involves powering down 12v for storage devices, this shouldn't
cause problem even if the attached device doesn't support slumber
mode.  However, in partial power management and suspend failure cases,
devices might lock up after suspend attempt.  I thought about removing
transition to slumber mode altogether but ahci spec mandates it before
HBA D3 state transition.  Blacklisting such devices might be the
solution.

Signed-off-by: Tejun Heo <htejun@gmail.com>

diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index af3565d1fefeda1785472e49470a242d041b1e63..f36da488a2c1c1ee9a62e54637bf1d46e7f4c0fd 100644 (file)
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -612,9 +612,6 @@ static void ahci_power_down(void __iomem *port_mmio, u32 cap)
 static void ahci_init_port(void __iomem *port_mmio, u32 cap,
                           dma_addr_t cmd_slot_dma, dma_addr_t rx_fis_dma)
 {
-       /* power up */
-       ahci_power_up(port_mmio, cap);
-
        /* enable FIS reception */
        ahci_start_fis_rx(port_mmio, cap, cmd_slot_dma, rx_fis_dma);
 
@@ -640,9 +637,6 @@ static int ahci_deinit_port(void __iomem *port_mmio, u32 cap, const char **emsg)
                return rc;
        }
 
-       /* put device into slumber mode */
-       ahci_power_down(port_mmio, cap);
-
        return 0;
 }
 
@@ -1321,7 +1315,9 @@ static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg)
        int rc;
 
        rc = ahci_deinit_port(port_mmio, hpriv->cap, &emsg);
-       if (rc) {
+       if (rc == 0)
+               ahci_power_down(port_mmio, hpriv->cap);
+       else {
                ata_port_printk(ap, KERN_ERR, "%s (%d)\n", emsg, rc);
                ahci_init_port(port_mmio, hpriv->cap,
                               pp->cmd_slot_dma, pp->rx_fis_dma);
@@ -1337,6 +1333,7 @@ static int ahci_port_resume(struct ata_port *ap)
        void __iomem *mmio = ap->host->mmio_base;
        void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
 
+       ahci_power_up(port_mmio, hpriv->cap);
        ahci_init_port(port_mmio, hpriv->cap, pp->cmd_slot_dma, pp->rx_fis_dma);
 
        return 0;
@@ -1443,6 +1440,9 @@ static int ahci_port_start(struct ata_port *ap)
 
        ap->private_data = pp;
 
+       /* power up port */
+       ahci_power_up(port_mmio, hpriv->cap);
+
        /* initialize port */
        ahci_init_port(port_mmio, hpriv->cap, pp->cmd_slot_dma, pp->rx_fis_dma);