This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
select DM_SERIAL
select DM_GPIO
-config TARGET_OMAP3_MVBLX
- bool "OMAP3 MVBLX"
-
config TARGET_NOKIA_RX51
bool "Nokia RX51"
source "board/corscience/tricorder/Kconfig"
source "board/htkw/mcx/Kconfig"
source "board/logicpd/omap3som/Kconfig"
-source "board/matrix_vision/mvblx/Kconfig"
source "board/nokia/rx51/Kconfig"
source "board/technexion/tao3530/Kconfig"
source "board/technexion/twister/Kconfig"
+++ /dev/null
-if TARGET_OMAP3_MVBLX
-
-config SYS_BOARD
- default "mvblx"
-
-config SYS_VENDOR
- default "matrix_vision"
-
-config SYS_CONFIG_NAME
- default "omap3_mvblx"
-
-endif
+++ /dev/null
-MVBLX BOARD
-M: Michael Jones <michael.jones@matrix-vision.de>
-S: Maintained
-F: board/matrix_vision/mvblx/
-F: include/configs/omap3_mvblx.h
-F: configs/omap3_mvblx_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += mvblx.o fpga.o
-obj-$(CONFIG_ID_EEPROM) += sys_eeprom.o
-
-ccflags-y += -Werror
+++ /dev/null
-#
-# (C) Copyright 2006
-# Texas Instruments, <www.ti.com>
-#
-# Beagle Board uses OMAP3 (ARM-CortexA8) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Physical Address:
-# 8000'0000 (bank0)
-# A000/0000 (bank1)
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-
-# For use with external or internal boots.
-CONFIG_SYS_TEXT_BASE = 0x80008000
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
- * Keith Outwater, keith_outwater@mvis.com.
- *
- * (C) Copyright 2011
- * Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
- * Michael Jones, Matrix Vision GmbH, michael.jones@matrix-vision.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ACEX1K.h>
-#include <command.h>
-#include <asm/gpio.h>
-#include <linux/byteorder/generic.h>
-#include "fpga.h"
-
-#ifdef FPGA_DEBUG
-#define fpga_debug(fmt, args...) printf("%s: "fmt, __func__, ##args)
-#else
-#define fpga_debug(fmt, args...)
-#endif
-
-Altera_CYC2_Passive_Serial_fns altera_fns = {
- fpga_null_fn, /* Altera_pre_fn */
- fpga_config_fn,
- fpga_status_fn,
- fpga_done_fn,
- fpga_wr_fn,
- fpga_null_fn,
- fpga_null_fn,
-};
-
-Altera_desc cyclone2 = {
- Altera_CYC2,
- fast_passive_parallel,
- Altera_EP3C5_SIZE,
- (void *) &altera_fns,
- NULL,
- 0
-};
-
-#define GPIO_RESET 43
-#define GPIO_DCLK 65
-#define GPIO_nSTATUS 157
-#define GPIO_CONF_DONE 158
-#define GPIO_nCONFIG 159
-#define GPIO_DATA0 54
-#define GPIO_DATA1 55
-#define GPIO_DATA2 56
-#define GPIO_DATA3 57
-#define GPIO_DATA4 58
-#define GPIO_DATA5 60
-#define GPIO_DATA6 61
-#define GPIO_DATA7 62
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* return FPGA_SUCCESS on success, else FPGA_FAIL
- */
-int mvblx_init_fpga(void)
-{
- fpga_debug("Initializing FPGA interface\n");
- fpga_init();
- fpga_add(fpga_altera, &cyclone2);
-
- if (gpio_request(GPIO_DCLK, "dclk") ||
- gpio_request(GPIO_nSTATUS, "nStatus") ||
-#ifndef CONFIG_SYS_FPGA_DONT_USE_CONF_DONE
- gpio_request(GPIO_CONF_DONE, "conf_done") ||
-#endif
- gpio_request(GPIO_nCONFIG, "nConfig") ||
- gpio_request(GPIO_DATA0, "data0") ||
- gpio_request(GPIO_DATA1, "data1") ||
- gpio_request(GPIO_DATA2, "data2") ||
- gpio_request(GPIO_DATA3, "data3") ||
- gpio_request(GPIO_DATA4, "data4") ||
- gpio_request(GPIO_DATA5, "data5") ||
- gpio_request(GPIO_DATA6, "data6") ||
- gpio_request(GPIO_DATA7, "data7")) {
- printf("%s: error requesting GPIOs.", __func__);
- return FPGA_FAIL;
- }
-
- /* set up outputs */
- gpio_direction_output(GPIO_DCLK, 0);
- gpio_direction_output(GPIO_nCONFIG, 0);
- gpio_direction_output(GPIO_DATA0, 0);
- gpio_direction_output(GPIO_DATA1, 0);
- gpio_direction_output(GPIO_DATA2, 0);
- gpio_direction_output(GPIO_DATA3, 0);
- gpio_direction_output(GPIO_DATA4, 0);
- gpio_direction_output(GPIO_DATA5, 0);
- gpio_direction_output(GPIO_DATA6, 0);
- gpio_direction_output(GPIO_DATA7, 0);
-
- /* NB omap_free_gpio() resets to an input, so we can't
- * free ie. nCONFIG, or else the FPGA would reset
- * Q: presumably gpio_free() has the same effect?
- */
-
- /* set up inputs */
- gpio_direction_input(GPIO_nSTATUS);
-#ifndef CONFIG_SYS_FPGA_DONT_USE_CONF_DONE
- gpio_direction_input(GPIO_CONF_DONE);
-#endif
-
- fpga_config_fn(0, 1, 0);
- udelay(60);
-
- return FPGA_SUCCESS;
-}
-
-int fpga_null_fn(int cookie)
-{
- return 0;
-}
-
-int fpga_config_fn(int assert, int flush, int cookie)
-{
- fpga_debug("SET config : %s=%d\n", assert ? "low" : "high", assert);
- if (flush) {
- gpio_set_value(GPIO_nCONFIG, !assert);
- udelay(1);
- gpio_set_value(GPIO_nCONFIG, assert);
- }
-
- return assert;
-}
-
-int fpga_done_fn(int cookie)
-{
- int result = 0;
-
- /* since revA of BLX, we will not get this signal. */
- udelay(10);
-#ifdef CONFIG_SYS_FPGA_DONT_USE_CONF_DONE
- fpga_debug("not waiting for CONF_DONE.");
- result = 1;
-#else
- fpga_debug("CONF_DONE check ... ");
- if (gpio_get_value(GPIO_CONF_DONE)) {
- fpga_debug("high\n");
- result = 1;
- } else
- fpga_debug("low\n");
- gpio_free(GPIO_CONF_DONE);
-#endif
-
- return result;
-}
-
-int fpga_status_fn(int cookie)
-{
- int result = 0;
- fpga_debug("STATUS check ... ");
-
- result = gpio_get_value(GPIO_nSTATUS);
-
- if (result < 0)
- fpga_debug("error\n");
- else if (result > 0)
- fpga_debug("high\n");
- else
- fpga_debug("low\n");
-
- return result;
-}
-
-static inline int _write_fpga(u8 byte)
-{
- gpio_set_value(GPIO_DATA0, byte & 0x01);
- gpio_set_value(GPIO_DATA1, (byte >> 1) & 0x01);
- gpio_set_value(GPIO_DATA2, (byte >> 2) & 0x01);
- gpio_set_value(GPIO_DATA3, (byte >> 3) & 0x01);
- gpio_set_value(GPIO_DATA4, (byte >> 4) & 0x01);
- gpio_set_value(GPIO_DATA5, (byte >> 5) & 0x01);
- gpio_set_value(GPIO_DATA6, (byte >> 6) & 0x01);
- gpio_set_value(GPIO_DATA7, (byte >> 7) & 0x01);
-
- /* clock */
- gpio_set_value(GPIO_DCLK, 1);
- udelay(1);
- gpio_set_value(GPIO_DCLK, 0);
- udelay(1);
-
- return 0;
-}
-
-int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie)
-{
- unsigned char *data = (unsigned char *) buf;
- int i;
- int headerlen = len - cyclone2.size;
-
- if (headerlen < 0)
- return FPGA_FAIL;
- else if (headerlen == sizeof(uint32_t)) {
- const unsigned int fpgavers_len = 11; /* '0x' + 8 hex digits + \0 */
- char fpgavers_str[fpgavers_len];
- snprintf(fpgavers_str, fpgavers_len, "0x%08x",
- be32_to_cpup((uint32_t*)data));
- setenv("fpgavers", fpgavers_str);
- }
-
- fpga_debug("fpga_wr: buf %p / size %d\n", buf, len);
- for (i = headerlen; i < len; i++)
- _write_fpga(data[i]);
- fpga_debug("-%s\n", __func__);
-
- return FPGA_SUCCESS;
-}
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
- * Keith Outwater, keith_outwater@mvis.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-extern int mvblx_init_fpga(void);
-
-extern int fpga_status_fn(int cookie);
-extern int fpga_config_fn(int assert, int flush, int cookie);
-extern int fpga_done_fn(int cookie);
-extern int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie);
-extern int fpga_null_fn(int cookie);
+++ /dev/null
-/*
- * MATRIX VISION GmbH mvBlueLYNX-X
- *
- * Derived from Beagle and Overo
- *
- * (C) Copyright 2004-2008
- * Texas Instruments, <www.ti.com>
- *
- * Author :
- * Sunil Kumar <sunilsaini05@gmail.com>
- * Shashi Ranjan <shashiranjanmca05@gmail.com>
- *
- * Derived from Beagle Board and 3430 SDP code by
- * Richard Woodruff <r-woodruff2@ti.com>
- * Syed Mohammed Khasim <khasim@ti.com>
- *
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-#include <netdev.h>
-#include <twl4030.h>
-#include <asm/io.h>
-#include <asm/arch/mem.h>
-#include <asm/arch/mmc_host_def.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/gpio.h>
-#include <asm/mach-types.h>
-#include "mvblx.h"
-#include "fpga.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_CMD_NET)
-static void setup_net_chip(void);
-#endif /* CONFIG_CMD_NET */
-
-/*
- * Routine: board_init
- * Description: Early hardware init.
- */
-int board_init(void)
-{
- gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
- /* boot param addr */
- gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
-
- return 0;
-}
-
-/*
- * Routine: misc_init_r
- * Description: Configure board specific parts
- */
-int misc_init_r(void)
-{
- printf("mvBlueLYNX-X\n");
- if (get_cpu_family() == CPU_OMAP36XX)
- setenv("mpurate", "1000");
- else
- setenv("mpurate", "600");
-
- twl4030_power_init();
-
-#if defined(CONFIG_CMD_NET)
- setup_net_chip();
-#endif /* CONFIG_CMD_NET */
-
- mvblx_init_fpga();
-
- mac_read_from_eeprom();
-
- dieid_num_r();
-
- return 0;
-}
-
-/*
- * Routine: set_muxconf_regs
- * Description: Setting up the configuration Mux registers specific to the
- * hardware. Many pins need to be moved from protect to primary
- * mode.
- */
-void set_muxconf_regs(void)
-{
- MUX_MVBLX();
-}
-
-#ifdef CONFIG_GENERIC_MMC
-int board_mmc_init(bd_t *bis)
-{
- omap_mmc_init(0, 0, 0, -1, -1);
- omap_mmc_init(1, 0, 0, -1, -1);
- return 0;
-}
-
-void board_mmc_power_init(void)
-{
- twl4030_power_mmc_init(0);
- twl4030_power_mmc_init(1);
-}
-#endif
-
-#if defined(CONFIG_CMD_NET)
-/*
- * Routine: setup_net_chip
- * Description: Setting up the configuration GPMC registers specific to the
- * Ethernet hardware.
- */
-static void setup_net_chip(void)
-{
- struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
- struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
-
- /* Configure GPMC registers */
- writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[0].config1);
- writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[0].config2);
- writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[0].config3);
- writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[0].config4);
- writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[0].config5);
- writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[0].config6);
- writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[0].config7);
-
- /* Enable off mode for NWE in PADCONF_GPMC_NWE register */
- writew(readw(&ctrl_base->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
- /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
- writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
- /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
- writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
- &ctrl_base->gpmc_nadv_ale);
-
- /* Make GPIO 139 as output pin */
- writel(readl(&gpio5_base->oe) & ~(GPIO11), &gpio5_base->oe);
-
- /* Now send a pulse on the GPIO pin */
- writel(GPIO11, &gpio5_base->setdataout);
- udelay(1);
- writel(GPIO11, &gpio5_base->cleardataout);
- udelay(1);
- writel(GPIO11, &gpio5_base->setdataout);
-}
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_SMC911X
- rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
-#endif
- return rc;
-}
-
-int overwrite_console(void)
-{
- /* return true if console should be overwritten */
- return 0;
-}
-
-#endif /* CONFIG_CMD_NET */
+++ /dev/null
-/*
- * (C) Copyright 2008
- * Dirk Behme <dirk.behme@gmail.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef _MVBLX_H_
-#define _MVBLX_H_
-
-#include <asm/arch/sys_proto.h>
-
-const omap3_sysinfo sysinfo = {
- DDR_DISCRETE,
- "OMAP3 mvBlueLYNX-X camera",
- "no NAND",
-};
-
-/*
- * IEN - Input Enable
- * IDIS - Input Disable
- * PTD - Pull type Down
- * PTU - Pull type Up
- * DIS - Pull type selection is inactive
- * EN - Pull type selection is active
- * M0 - Mode 0
- * The commented string gives the final mux configuration for that pin
- */
-#define MUX_MVBLX() \
- /*SDRC*/\
- MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
- MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
- MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
- MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
- MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
- MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
- MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
- MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
- MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
- MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
- MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
- MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
- MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
- MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
- MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
- MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
- MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
- MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
- MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
- MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
- MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
- MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
- MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
- MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
- MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
- MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
- MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
- MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
- MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
- MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
- MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
- MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
- MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
- MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
- MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
- MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
- MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
- /*GPMC*/\
- MUX_VAL(CP(GPMC_A1), (IDIS | PTU | EN | M0)) /*GPMC_A1*/\
- MUX_VAL(CP(GPMC_A2), (IDIS | PTU | EN | M0)) /*GPMC_A2*/\
- MUX_VAL(CP(GPMC_A3), (IDIS | PTU | EN | M0)) /*GPMC_A3*/\
- MUX_VAL(CP(GPMC_A4), (IDIS | PTU | EN | M0)) /*GPMC_A4*/\
- MUX_VAL(CP(GPMC_A5), (IDIS | PTU | EN | M0)) /*GPMC_A5*/\
- MUX_VAL(CP(GPMC_A6), (IDIS | PTU | EN | M0)) /*GPMC_A6*/\
- MUX_VAL(CP(GPMC_A7), (IDIS | PTU | EN | M0)) /*GPMC_A7*/\
- MUX_VAL(CP(GPMC_A8), (IDIS | PTU | EN | M4)) /*GPIO_41*/\
- MUX_VAL(CP(GPMC_A9), (IDIS | PTU | EN | M4)) /*GPIO_42*/\
- MUX_VAL(CP(GPMC_A10), (IDIS | PTU | EN | M4)) /*GPIO_43*/\
- MUX_VAL(CP(GPMC_D0), (IEN | PTU | EN | M0)) /*GPMC_D0*/\
- MUX_VAL(CP(GPMC_D1), (IEN | PTU | EN | M0)) /*GPMC_D1*/\
- MUX_VAL(CP(GPMC_D2), (IEN | PTU | EN | M0)) /*GPMC_D2*/\
- MUX_VAL(CP(GPMC_D3), (IEN | PTU | EN | M0)) /*GPMC_D3*/\
- MUX_VAL(CP(GPMC_D4), (IEN | PTU | EN | M0)) /*GPMC_D4*/\
- MUX_VAL(CP(GPMC_D5), (IEN | PTU | EN | M0)) /*GPMC_D5*/\
- MUX_VAL(CP(GPMC_D6), (IEN | PTU | EN | M0)) /*GPMC_D6*/\
- MUX_VAL(CP(GPMC_D7), (IEN | PTU | EN | M0)) /*GPMC_D7*/\
- MUX_VAL(CP(GPMC_D8), (IEN | PTU | EN | M0)) /*GPMC_D8*/\
- MUX_VAL(CP(GPMC_D9), (IEN | PTU | EN | M0)) /*GPMC_D9*/\
- MUX_VAL(CP(GPMC_D10), (IEN | PTU | EN | M0)) /*GPMC_D10*/\
- MUX_VAL(CP(GPMC_D11), (IEN | PTU | EN | M0)) /*GPMC_D11*/\
- MUX_VAL(CP(GPMC_D12), (IEN | PTU | EN | M0)) /*GPMC_D12*/\
- MUX_VAL(CP(GPMC_D13), (IEN | PTU | EN | M0)) /*GPMC_D13*/\
- MUX_VAL(CP(GPMC_D14), (IEN | PTU | EN | M0)) /*GPMC_D14*/\
- MUX_VAL(CP(GPMC_D15), (IEN | PTU | EN | M0)) /*GPMC_D15*/\
- MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
- MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /*GPMC_nCS1*/\
- MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /*GPMC_nCS2*/\
- MUX_VAL(CP(GPMC_NCS3), (IEN | PTU | EN | M4)) /*GPIO54*/\
- MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M4)) /*GPIO55*/\
- MUX_VAL(CP(GPMC_NCS5), (IEN | PTU | EN | M4)) /*GPIO56*/\
- MUX_VAL(CP(GPMC_NCS6), (IEN | PTU | EN | M4)) /*GPIO57*/\
- MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M4)) /*GPIO58*/\
- MUX_VAL(CP(GPMC_CLK), (IDIS | PTU | EN | M0)) /*GPMC_CLK*/\
- MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
- MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
- MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
- MUX_VAL(CP(GPMC_NBE0_CLE), (IEN | PTU | EN | M4)) /*GPIO60*/\
- MUX_VAL(CP(GPMC_NBE1), (IEN | PTU | EN | M4)) /*GPIO61*/\
- MUX_VAL(CP(GPMC_NWP), (IEN | PTU | EN | M4)) /*GPIO62*/\
- MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
- MUX_VAL(CP(GPMC_WAIT3), (IDIS | PTU | EN | M4)) /*GPIO65*/\
- /*DSS*/\
- MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
- MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
- MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
- MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
- MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M4)) /*not_used*/\
- MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M4)) /*not_used*/\
- MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M4)) /*not_used*/\
- MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M4)) /*not_used*/\
- MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M4)) /*not_used*/\
- MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M4)) /*not_used*/\
- MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
- MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
- MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
- MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
- MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
- MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
- MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
- MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
- MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
- MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
- MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
- MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
- MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M3)) /*DSS_DATA0*/\
- MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M3)) /*DSS_DATA1*/\
- MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M3)) /*DSS_DATA2*/\
- MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M3)) /*DSS_DATA3*/\
- MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M3)) /*DSS_DATA4*/\
- MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M3)) /*DSS_DATA5*/\
- /*CAMERA*/\
- MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) /*CAM_HS */\
- MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) /*CAM_VS */\
- MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
- MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) /*CAM_PCLK*/\
- MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\
- MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) /*CAM_D0*/\
- MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) /*CAM_D1*/\
- MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) /*CAM_D2*/\
- MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) /*CAM_D3*/\
- MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) /*CAM_D4*/\
- MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) /*CAM_D5*/\
- MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) /*CAM_D6*/\
- MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) /*CAM_D7*/\
- MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) /*CAM_D8*/\
- MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) /*CAM_D9*/\
- MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) /*CAM_D10*/\
- MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) /*CAM_D11*/\
- MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
- MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\
- MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
- MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
- MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
- MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
- MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) /*CSI2_DY1*/\
- /*Audio Interface */\
- MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
- MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0)) /*McBSP2_CLKX*/\
- MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) /*McBSP2_DR*/\
- MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
- /*Expansion card 1*/\
- MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/\
- MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/\
- MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/\
- MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/\
- MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/\
- MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/\
- MUX_VAL(CP(MMC1_DAT4), (IDIS | PTU | DIS | M4)) /*GPIO_?*/\
- MUX_VAL(CP(MMC1_DAT5), (IDIS | PTU | DIS | M4)) /*GPIO_?*/\
- MUX_VAL(CP(MMC1_DAT6), (IDIS | PTU | DIS | M4)) /*GPIO_?*/\
- MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | DIS | M7)) /*GPIO_129 disabled*/\
- /*Expansion card 2 */\
- MUX_VAL(CP(MMC2_CLK), (IEN | PTU | DIS | M0)) /*MMC2_CLK*/\
- MUX_VAL(CP(MMC2_CMD), (IEN | PTU | DIS | M0)) /*MMC2_CMD*/\
- MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | DIS | M0)) /*MMC2_DAT0*/\
- MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | DIS | M0)) /*MMC2_DAT1*/\
- MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | DIS | M0)) /*MMC2_DAT2*/\
- MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | DIS | M0)) /*MMC2_DAT3*/\
- MUX_VAL(CP(MMC2_DAT4), (IDIS | PTU | DIS | M4)) /*GPIO_136*/\
- MUX_VAL(CP(MMC2_DAT5), (IEN | PTU | EN | M4)) /*GPIO_137*/\
- MUX_VAL(CP(MMC2_DAT6), (IDIS | PTU | DIS | M4)) /*GPIO_138*/\
- MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M4)) /*GPIO_139*/\
- /*Bluetooth*/\
- MUX_VAL(CP(MCBSP3_DX), (IDIS | PTD | DIS | M1)) /*UART2_CTS*/\
- MUX_VAL(CP(MCBSP3_DR), (IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
- MUX_VAL(CP(MCBSP3_CLKX), (IDIS | PTD | DIS | M1)) /*UART2_TX*/\
- MUX_VAL(CP(MCBSP3_FSX), (IDIS | PTD | DIS | M1)) /*UART2_RX*/\
- /*Modem Interface */\
- MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
- MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M4)) /*GPIO_149*/ \
- MUX_VAL(CP(UART1_CTS), (IEN | PTU | EN | M4)) /*GPIO_150*/ \
- MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) /*UART1_RX*/\
- MUX_VAL(CP(MCBSP1_CLKR), (IDIS | PTD | DIS | M4)) /*GPIO_156*/\
- MUX_VAL(CP(MCBSP1_FSR), (IEN | PTU | EN | M4)) /*GPIO_157*/\
- MUX_VAL(CP(MCBSP1_DX), (IEN | PTU | DIS | M4)) /*GPIO_158 1-wire */\
- MUX_VAL(CP(MCBSP1_DR), (IDIS | PTD | DIS | M4)) /*GPIO_159*/\
- MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) /*McBSP_CLKS*/\
- MUX_VAL(CP(MCBSP1_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_161*/\
- MUX_VAL(CP(MCBSP1_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_162*/\
- /*Serial Interface*/\
- MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0)) /*UART3_CTS_RCTX*/\
- MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) /*UART3_RTS_SD */\
- MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) /*UART3_RX_IRRX*/\
- MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
- MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
- MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
- MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) /*HSUSB0_DIR*/\
- MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) /*HSUSB0_NXT*/\
- MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA0*/\
- MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA1*/\
- MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA2*/\
- MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA3*/\
- MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA4*/\
- MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA5*/\
- MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA6*/\
- MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
- MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL*/\
- MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA*/\
- MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)) /*I2C2_SCL*/\
- MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)) /*I2C2_SDA*/\
- MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) /*I2C3_SCL*/\
- MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) /*I2C3_SDA*/\
- MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /*I2C4_SCL*/\
- MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /*I2C4_SDA*/\
- MUX_VAL(CP(HDQ_SIO), (IDIS | PTU | EN | M4)) /*GPIO_170*/\
- MUX_VAL(CP(MCSPI1_CLK), (IDIS | PTU | DIS | M4)) /*GPIO_171*/\
- MUX_VAL(CP(MCSPI1_SIMO), (IDIS | PTU | DIS | M4)) /*GPIO_172*/\
- MUX_VAL(CP(MCSPI1_SOMI), (IDIS | PTU | DIS | M4)) /*GPIO_173*/\
- MUX_VAL(CP(MCSPI1_CS0), (IDIS | PTD | DIS | M4)) /*GPIO_174*/\
- MUX_VAL(CP(MCSPI1_CS3), (IDIS | PTU | DIS | M4)) /*GPIO_177*/\
- /* USB EHCI (port 2) not used */\
- MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M0)) /*McSPI2_CLK*/\
- MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M0)) /*McSPI2_SIMO*/\
- MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M0)) /*McSPI2_SOMI*/\
- MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M0)) /*McSPI2_CS0*/\
- MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M0)) /*McSPI2_CS1*/\
- /*Control and debug */\
- MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
- MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
- MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
- MUX_VAL(CP(SYS_BOOT0), (IDIS | PTD | DIS | M3)) /*DSS_DATA18*/\
- MUX_VAL(CP(SYS_BOOT1), (IDIS | PTD | DIS | M3)) /*DSS_DATA19*/\
- MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M0)) /*GPIO_4*/\
- MUX_VAL(CP(SYS_BOOT3), (IDIS | PTD | DIS | M3)) /*DSS_DATA20*/\
- MUX_VAL(CP(SYS_BOOT4), (IDIS | PTD | DIS | M3)) /*DSS_DATA21*/\
- MUX_VAL(CP(SYS_BOOT5), (IDIS | PTD | DIS | M3)) /*DSS_DATA22*/\
- MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M3)) /*DSS_DATA23*/ \
- MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) /*SYS_OFF_MODE*/\
- MUX_VAL(CP(SYS_CLKOUT1), (IDIS | PTD | DIS | M4)) /*GPIO_10*/\
- MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTD | DIS | M0)) /*SYS_CLKOUT2*/\
- /* USB EHCI (port 1) */\
- MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M3)) /*HSUSB1_STP*/\
- MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB1_CLK*/\
- MUX_VAL(CP(ETK_D0_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA0*/\
- MUX_VAL(CP(ETK_D1_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA1*/\
- MUX_VAL(CP(ETK_D2_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA2*/\
- MUX_VAL(CP(ETK_D3_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA7*/\
- MUX_VAL(CP(ETK_D4_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA4*/\
- MUX_VAL(CP(ETK_D5_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA5*/\
- MUX_VAL(CP(ETK_D6_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA6*/\
- MUX_VAL(CP(ETK_D7_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DATA3*/\
- MUX_VAL(CP(ETK_D8_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DIR*/\
- MUX_VAL(CP(ETK_D9_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_NXT*/\
- MUX_VAL(CP(ETK_D10_ES2), (IEN | PTU | EN | M4)) /*GPIO_24*/\
- MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | DIS | M4)) /*GPIO_25*/\
- MUX_VAL(CP(ETK_D12_ES2), (IEN | PTU | DIS | M4)) /*GPIO_26*/\
- MUX_VAL(CP(ETK_D13_ES2), (IEN | PTU | DIS | M4)) /*GPIO_27*/\
- MUX_VAL(CP(ETK_D14_ES2), (IEN | PTU | DIS | M4)) /*GPIO_28*/\
- MUX_VAL(CP(ETK_D15_ES2), (IEN | PTU | DIS | M4)) /*GPIO_29*/\
- /*Die to Die */\
- MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\
- MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\
- MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0)) /*d2d_mcad3*/\
- MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0)) /*d2d_mcad4*/\
- MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0)) /*d2d_mcad5*/\
- MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0)) /*d2d_mcad6*/\
- MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0)) /*d2d_mcad7*/\
- MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0)) /*d2d_mcad8*/\
- MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0)) /*d2d_mcad9*/\
- MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0)) /*d2d_mcad10*/\
- MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0)) /*d2d_mcad11*/\
- MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0)) /*d2d_mcad12*/\
- MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0)) /*d2d_mcad13*/\
- MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0)) /*d2d_mcad14*/\
- MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0)) /*d2d_mcad15*/\
- MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0)) /*d2d_mcad16*/\
- MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0)) /*d2d_mcad17*/\
- MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0)) /*d2d_mcad18*/\
- MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0)) /*d2d_mcad19*/\
- MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0)) /*d2d_mcad20*/\
- MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0)) /*d2d_mcad21*/\
- MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0)) /*d2d_mcad22*/\
- MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0)) /*d2d_mcad23*/\
- MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0)) /*d2d_mcad24*/\
- MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0)) /*d2d_mcad25*/\
- MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0)) /*d2d_mcad26*/\
- MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0)) /*d2d_mcad27*/\
- MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0)) /*d2d_mcad28*/\
- MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0)) /*d2d_mcad29*/\
- MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0)) /*d2d_mcad30*/\
- MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0)) /*d2d_mcad31*/\
- MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0)) /*d2d_mcad32*/\
- MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0)) /*d2d_mcad33*/\
- MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) /*d2d_mcad34*/\
- MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) /*d2d_mcad35*/\
- MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) /*d2d_mcad36*/\
- MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) /*d2d_clk26mi*/\
- MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) /*d2d_nrespwron*/\
- MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) /*d2d_nreswarm */\
- MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) /*d2d_arm9nirq */\
- MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
- MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) /*d2d_spint*/\
- MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) /*d2d_frint*/\
- MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) /*d2d_dmareq0*/\
- MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) /*d2d_dmareq1*/\
- MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) /*d2d_dmareq2*/\
- MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) /*d2d_dmareq3*/\
- MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) /*d2d_n3gtrst*/\
- MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) /*d2d_n3gtdi*/\
- MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) /*d2d_n3gtdo*/\
- MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) /*d2d_n3gtms*/\
- MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) /*d2d_n3gtck*/\
- MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) /*d2d_n3grtck*/\
- MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) /*d2d_mstdby*/\
- MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) /*d2d_swakeup*/\
- MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) /*d2d_idlereq*/\
- MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) /*d2d_idleack*/\
- MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) /*d2d_mwrite*/\
- MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) /*d2d_swrite*/\
- MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) /*d2d_mread*/\
- MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) /*d2d_sread*/\
- MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_mbusflag*/\
- MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) /*d2d_sbusflag*/\
- MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
- MUX_VAL(CP(SDRC_CKE1), (IDIS | PTU | EN | M0)) /*sdrc_cke1*/
-
-#endif
+++ /dev/null
-/*
- * Copyright 2006, 2008-2009, 2011 Freescale Semiconductor
- * York Sun (yorksun@freescale.com)
- * Haiying Wang (haiying.wang@freescale.com)
- * Timur Tabi (timur@freescale.com)
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <i2c.h>
-
-/* #define DEBUG */
-
-/*
- * static eeprom: EEPROM layout
- */
-static struct __attribute__ ((__packed__)) eeprom {
- u8 id[16]; /* 0x01 - 0x0F Type e.g. 100wG-5111 */
- u8 sn[10]; /* 0x10 - 0x19 Serial Number */
- u8 date[6]; /* 0x1A - 0x1F Build Date */
- u8 mac[6]; /* 0x20 - 0x25 MAC address */
- u8 reserved[10];/* 0x26 - 0x2f reserved */
- u32 crc; /* x+1 CRC32 checksum */
-} e;
-
-/* Set to 1 if we've read EEPROM into memory */
-static int has_been_read;
-
-/**
- * show_eeprom - display the contents of the EEPROM
- */
-static void show_eeprom(void)
-{
- unsigned int crc;
- char safe_string[16];
-
-#ifdef DEBUG
- int i;
-#endif
- u8 *p;
-
- /* ID */
- strncpy(safe_string, (char *)e.id, sizeof(e.id));
- safe_string[sizeof(e.id)-1] = 0;
- printf("ID: mvBlueLYNX-X%s\n", safe_string);
-
- /* Serial number */
- strncpy(safe_string, (char *)e.sn, sizeof(e.sn));
- safe_string[sizeof(e.sn)-1] = 0;
- printf("SN: %s\n", safe_string);
-
- /* Build date, BCD date values, as YYMMDDhhmmss */
- printf("Build date: 20%02x/%02x/%02x %02x:%02x:%02x %s\n",
- e.date[0], e.date[1], e.date[2],
- e.date[3] & 0x7F, e.date[4], e.date[5],
- e.date[3] & 0x80 ? "PM" : "");
-
- /* Show MAC address */
- p = e.mac;
- printf("Eth: %02x:%02x:%02x:%02x:%02x:%02x\n",
- p[0], p[1], p[2], p[3], p[4], p[5]);
-
- crc = crc32(0, (void *)&e, sizeof(e) - 4);
-
- if (crc == be32_to_cpu(e.crc))
- printf("CRC: %08x\n", be32_to_cpu(e.crc));
- else
- printf("CRC: %08x (should be %08x)\n", be32_to_cpu(e.crc), crc);
-
-#ifdef DEBUG
- printf("EEPROM dump: (0x%x bytes)\n", sizeof(e));
- for (i = 0; i < sizeof(e); i++) {
- if ((i % 16) == 0)
- printf("%02X: ", i);
- printf("%02X ", ((u8 *)&e)[i]);
- if (((i % 16) == 15) || (i == sizeof(e) - 1))
- printf("\n");
- }
-#endif
-}
-
-/**
- * read_eeprom - read the EEPROM into memory
- */
-static int read_eeprom(void)
-{
- int ret;
-#ifdef CONFIG_SYS_EEPROM_BUS_NUM
- unsigned int bus;
-#endif
-
- if (has_been_read)
- return 0;
-
-#ifdef CONFIG_SYS_EEPROM_BUS_NUM
- bus = i2c_get_bus_num();
- i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM);
-#endif
-
- ret = eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
- (uchar *)&e, sizeof(e));
-
-#ifdef CONFIG_SYS_EEPROM_BUS_NUM
- i2c_set_bus_num(bus);
-#endif
-
-#ifdef DEBUG
- show_eeprom();
-#endif
-
- has_been_read = (ret == 0) ? 1 : 0;
-
- return ret;
-}
-
-/**
- * update_crc - update the CRC
- *
- * This function should be called after each update to the EEPROM structure,
- * to make sure the CRC is always correct.
- */
-static void update_crc(void)
-{
- u32 crc;
-
- crc = crc32(0, (void *)&e, sizeof(e) - 4);
- e.crc = cpu_to_be32(crc);
-}
-
-/**
- * prog_eeprom - write the EEPROM from memory
- */
-static int prog_eeprom(void)
-{
- int ret = 0;
-#ifdef CONFIG_SYS_EEPROM_BUS_NUM
- unsigned int bus;
-#endif
-
- update_crc();
-
-#ifdef CONFIG_SYS_EEPROM_BUS_NUM
- bus = i2c_get_bus_num();
- i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM);
-#endif
-
- ret = eeprom_write(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
- (uchar *)&e, sizeof(e));
-
- if (!ret) {
- /* Verify the write by reading back the EEPROM and comparing */
- struct eeprom e2;
-#ifdef DEBUG
- printf("%s verifying...\n", __func__);
-#endif
- ret = eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
- (uchar *)&e2, sizeof(e2));
-
- if (!ret && memcmp(&e, &e2, sizeof(e)))
- ret = -1;
- }
-
-#ifdef CONFIG_SYS_EEPROM_BUS_NUM
- i2c_set_bus_num(bus);
-#endif
-
- if (ret) {
- printf("Programming failed.\n");
- has_been_read = 0;
- return -1;
- }
-
- printf("Programming passed.\n");
- return 0;
-}
-
-/**
- * h2i - converts hex character into a number
- *
- * This function takes a hexadecimal character (e.g. '7' or 'C') and returns
- * the integer equivalent.
- */
-static inline u8 h2i(char p)
-{
- if ((p >= '0') && (p <= '9'))
- return p - '0';
-
- if ((p >= 'A') && (p <= 'F'))
- return (p - 'A') + 10;
-
- if ((p >= 'a') && (p <= 'f'))
- return (p - 'a') + 10;
-
- return 0;
-}
-
-/**
- * set_date - stores the build date into the EEPROM
- *
- * This function takes a pointer to a string in the format "YYMMDDhhmmss"
- * (2-digit year, 2-digit month, etc), converts it to a 6-byte BCD string,
- * and stores it in the build date field of the EEPROM local copy.
- */
-static void set_date(const char *string)
-{
- unsigned int i;
-
- if (strlen(string) != 12) {
- printf("Usage: mac date YYMMDDhhmmss\n");
- return;
- }
-
- for (i = 0; i < 6; i++)
- e.date[i] = h2i(string[2 * i]) << 4 | h2i(string[2 * i + 1]);
-
- update_crc();
-}
-
-/**
- * set_mac_address - stores a MAC address into the EEPROM
- *
- * This function takes a pointer to MAC address string
- * (i.e."XX:XX:XX:XX:XX:XX", where "XX" is a two-digit hex number) and
- * stores it in the MAC address field in the EEPROM local copy.
- */
-static void set_mac_address(const char *string)
-{
- char *p = (char *) string;
- unsigned int i;
-
- for (i = 0; *p && (i < 6); i++) {
- e.mac[i] = simple_strtoul(p, &p, 16);
- if (*p == ':')
- p++;
- }
-
- update_crc();
-}
-
-int do_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- char cmd;
-
- if (argc == 1) {
- show_eeprom();
- return 0;
- }
-
- cmd = argv[1][0];
-
- if (cmd == 'r') {
-#ifdef DEBUG
- printf("%s read\n", __func__);
-#endif
- read_eeprom();
- return 0;
- }
-
- if (argc == 2) {
- switch (cmd) {
- case 's': /* save */
-#ifdef DEBUG
- printf("%s save\n", __func__);
-#endif
- prog_eeprom();
- break;
- default:
- return cmd_usage(cmdtp);
- }
-
- return 0;
- }
-
- /* We know we have at least one parameter */
-
- switch (cmd) {
- case 'n': /* serial number */
-#ifdef DEBUG
- printf("%s serial number\n", __func__);
-#endif
- memset(e.sn, 0, sizeof(e.sn));
- strncpy((char *)e.sn, argv[2], sizeof(e.sn) - 1);
- update_crc();
- break;
- case 'd': /* date BCD format YYMMDDhhmmss */
- set_date(argv[2]);
- break;
- case 'e': /* errata */
- printf("mac errata not implemented\n");
- break;
- case 'i': /* id */
- memset(e.id, 0, sizeof(e.id));
- strncpy((char *)e.id, argv[2], sizeof(e.id) - 1);
- update_crc();
- break;
- case 'p': /* ports */
- printf("mac ports not implemented (always 1 port)\n");
- break;
- case '0' ... '9':
- /* we only have "mac 0" but any digit can be used here */
- set_mac_address(argv[2]);
- break;
- case 'h': /* help */
- default:
- return cmd_usage(cmdtp);
- }
-
- return 0;
-}
-
-static inline int is_portrait(void)
-{
- int i;
- unsigned int orient_index = 0; /* idx of char which determines orientation */
-
- for (i = sizeof(e.id)/sizeof(*e.id) - 1; i>=0; i--) {
- if (e.id[i] == '-') {
- orient_index = i+1;
- break;
- }
- }
-
- return (orient_index &&
- (e.id[orient_index] >= '5') && (e.id[orient_index] <= '8'));
-}
-
-int mac_read_from_eeprom(void)
-{
- u32 crc, crc_offset = offsetof(struct eeprom, crc);
- u32 *crcp; /* Pointer to the CRC in the data read from the EEPROM */
-#define FILENAME_LANDSCAPE "mvBlueLynx_X.rbf"
-#define FILENAME_PORTRAIT "mvBlueLynx_X_sensor_cd.rbf"
-
- if (read_eeprom()) {
- printf("EEPROM Read failed.\n");
- return -1;
- }
-
- crc = crc32(0, (void *)&e, crc_offset);
- crcp = (void *)&e + crc_offset;
- if (crc != be32_to_cpu(*crcp)) {
- printf("EEPROM CRC mismatch (%08x != %08x)\n", crc,
- be32_to_cpu(e.crc));
- return -1;
- }
-
- if (memcmp(&e.mac, "\0\0\0\0\0\0", 6) &&
- memcmp(&e.mac, "\xFF\xFF\xFF\xFF\xFF\xFF", 6)) {
- char ethaddr[18];
-
- sprintf(ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X",
- e.mac[0],
- e.mac[1],
- e.mac[2],
- e.mac[3],
- e.mac[4],
- e.mac[5]);
- /* Only initialize environment variables that are blank
- * (i.e. have not yet been set)
- */
- if (!getenv("ethaddr"))
- setenv("ethaddr", ethaddr);
- }
-
- if (memcmp(&e.sn, "\0\0\0\0\0\0\0\0\0\0", 10) &&
- memcmp(&e.sn, "\xFF\xFF\xFF\xFF\xFF\xFF\xFF\xFF\xFF\xFF", 10)) {
- char serial_num[12];
-
- strncpy(serial_num, (char *)e.sn, sizeof(e.sn) - 1);
- /* Only initialize environment variables that are blank
- * (i.e. have not yet been set)
- */
- if (!getenv("serial#"))
- setenv("serial#", serial_num);
- }
-
- /* decide which fpga file to load depending on orientation */
- if (is_portrait())
- setenv("fpgafilename", FILENAME_PORTRAIT);
- else
- setenv("fpgafilename", FILENAME_LANDSCAPE);
-
- /* TODO should I calculate CRC here? */
- return 0;
-}
-
-#ifdef CONFIG_SERIAL_TAG
-void get_board_serial(struct tag_serialnr *serialnr)
-{
- char *serial = getenv("serial#");
-
- if (serial && (strlen(serial) > 3)) {
- /* use the numerical part of the serial number LXnnnnnn */
- serialnr->high = 0;
- serialnr->low = simple_strtoul(serial + 2, NULL, 10);
- } else {
- serialnr->high = 0;
- serialnr->low = 0;
- }
-}
-#endif
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_OMAP34XX=y
-CONFIG_TARGET_OMAP3_MVBLX=y
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_STOP_STR="S"
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="mvblx # "
make cm_t35_config
make
-* BlueLYNX-X:
-
-make omap3_mvblx_config
-make
Custom commands
===============
+++ /dev/null
-/*
- * MATRIX VISION GmbH mvBlueLYNX-X
- *
- * Derived from omap3_beagle.h:
- * (C) Copyright 2006-2008
- * Texas Instruments.
- * Richard Woodruff <r-woodruff2@ti.com>
- * Syed Mohammed Khasim <x0khasim@ti.com>
- *
- * Configuration settings for the TI OMAP3530 Beagle board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_OMAP 1 /* in a TI OMAP core */
-#define CONFIG_MVBLX 1 /* working with mvBlueLYNX-X */
-#define CONFIG_MACH_TYPE MACH_TYPE_MVBLX
-#define CONFIG_OMAP_GPIO
-#define CONFIG_OMAP_COMMON
-/* Common ARM Erratas */
-#define CONFIG_ARM_ERRATA_454179
-#define CONFIG_ARM_ERRATA_430973
-#define CONFIG_ARM_ERRATA_621766
-
-#define CONFIG_SDRC /* The chip has SDRC controller */
-
-#include <asm/arch/cpu.h> /* get chip and board defs */
-#include <asm/arch/omap.h>
-
-/*
- * Display CPU and Board information
- */
-#define CONFIG_DISPLAY_CPUINFO 1
-#define CONFIG_DISPLAY_BOARDINFO 1
-
-/* Clock Defines */
-#define V_OSCK 26000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK >> 1)
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_OF_LIBFDT 1
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-#define CONFIG_REVISION_TAG 1
-#define CONFIG_SERIAL_TAG 1
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_ENV_SIZE (2 << 10) /* 2 KiB */
- /* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
-
-/*
- * Hardware drivers
- */
-
-/*
- * NS16550 Configuration
- */
-#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-
-/*
- * select serial console configuration
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
-#define CONFIG_SERIAL1 1 /* UART1 */
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
- 115200}
-#define CONFIG_GENERIC_MMC 1
-#define CONFIG_MMC 1
-#define CONFIG_OMAP_HSMMC 1
-#define CONFIG_DOS_PARTITION 1
-
-/* silent console by default */
-#define CONFIG_SYS_DEVICE_NULLDEV 1
-#define CONFIG_SILENT_CONSOLE 1
-
-/* USB */
-#define CONFIG_USB_MUSB_UDC 1
-#define CONFIG_USB_OMAP3 1
-#define CONFIG_TWL4030_USB 1
-
-/* USB device configuration */
-#define CONFIG_USB_DEVICE 1
-#define CONFIG_USB_TTY 1
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE 1
-#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE 1
-#define CONFIG_USBD_VENDORID 0x164c
-#define CONFIG_USBD_PRODUCTID_GSERIAL 0x0201
-#define CONFIG_USBD_PRODUCTID_CDCACM 0x0201
-#define CONFIG_USBD_MANUFACTURER "MATRIX VISION GmbH"
-#define CONFIG_USBD_PRODUCT_NAME "mvBlueLYNX-X"
-
-/* no FLASH available */
-#define CONFIG_SYS_NO_FLASH
-
-/* commands to include */
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_FPGA_LOADMK
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_OMAP34XX
-
-/*
- * TWL4030
- */
-#define CONFIG_TWL4030_POWER 1
-
-/* Environment information */
-#undef CONFIG_ENV_OVERWRITE /* disallow overwriting serial# and ethaddr */
-#define CONFIG_BOOTDELAY 0
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "silent=true\0" \
- "loadaddr=0x82000000\0" \
- "usbtty=cdc_acm\0" \
- "console=ttyO0,115200n8\0" \
- "mpurate=600\0" \
- "vram=12M\0" \
- "dvimode=1024x768-24@60\0" \
- "defaultdisplay=dvi\0" \
- "loadfpga=if ext2load mmc ${mmcdev}:2 ${loadaddr} "\
- "/lib/firmware/mvblx/${fpgafilename}; then " \
- "fpga load 0 ${loadaddr} ${filesize}; " \
- "fi;\0" \
- "mmcdev=0\0" \
- "mmcroot=/dev/mmcblk0p2 rw\0" \
- "mmcrootfstype=ext3 rootwait\0" \
- "mmcargs=setenv bootargs console=${console} " \
- "mpurate=${mpurate} " \
- "vram=${vram} " \
- "omapfb.mode=dvi:${dvimode} " \
- "omapfb.debug=y " \
- "omapdss.def_disp=${defaultdisplay} " \
- "root=${mmcroot} " \
- "rootfstype=${mmcrootfstype} " \
- "mvfw.fpgavers=${fpgavers} " \
- "${cmdline_suffix}\0" \
- "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \
- "importbootenv=echo Importing environment from mmc ...; " \
- "env import -t $loadaddr $filesize\0" \
- "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "bootm ${loadaddr}\0" \
- "mmcbootcmd= " \
- "echo Trying mmc${mmcdev}; " \
- "mmc dev ${mmcdev}; " \
- "if mmc rescan; then " \
- "setenv mmcroot /dev/mmcblk${mmcdev}p2 rw; " \
- "echo SD/MMC found on device ${mmcdev};" \
- "if run loadbootenv; then " \
- "echo Loading boot environment from mmc${mmcdev}; " \
- "run importbootenv; " \
- "fi;" \
- "run loadfpga; " \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...;" \
- "run uenvcmd;" \
- "fi;" \
- "if run loaduimage; then " \
- "run mmcboot; " \
- "fi;" \
- "fi\0"
-
-#define CONFIG_BOOTCOMMAND \
- "setenv mmcdev 1;" \
- "run mmcbootcmd || " \
- "setenv mmcdev 0;" \
- "run mmcbootcmd"
-
-
-#define CONFIG_AUTO_COMPLETE 1
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-
-#define CONFIG_SYS_ALT_MEMTEST 1 /* alternative memtest with looping */
-#define CONFIG_SYS_MEMTEST_START (0x82000000) /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END (0x9dffffff) /* end = 448 MB */
-#define CONFIG_SYS_MEMTEST_SCRATCH (0x81000000) /* dummy address */
-
-/* default load address */
-#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)
-
-/*
- * OMAP3 has 12 GP timers, they can be driven by the system clock
- * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
- * This rate is divided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-
-#define CONFIG_ENV_IS_NOWHERE 1
-
-/*----------------------------------------------------------------------------
- * Network Subsystem (SMSC9211 Ethernet from SMSC9118 family)
- *----------------------------------------------------------------------------
- */
-#if defined(CONFIG_CMD_NET)
- #define CONFIG_SMC911X 1
- #define CONFIG_SMC911X_32_BIT
- #define CONFIG_SMC911X_BASE 0x2C000000
-#endif /* (CONFIG_CMD_NET) */
-
-#define CONFIG_FPGA_COUNT 1
-#define CONFIG_FPGA
-#define CONFIG_FPGA_ALTERA
-#define CONFIG_FPGA_CYCLON2
-#define CONFIG_SYS_FPGA_PROG_FEEDBACK
-#define CONFIG_SYS_FPGA_DONT_USE_CONF_DONE
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 0xA0>>1 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 2^4 = 16-byte pages */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-#define CONFIG_SYS_EEPROM_SIZE 256 /* Bytes */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_EEPROM_BUS_NUM 2
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
-#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_OMAP3_SPI
-
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
-#endif /* __CONFIG_H */
projects / project / bcm63xx / u-boot.git / commitdiff