#
# U-boot - Makefile
#
-# Copyright (c) 2005-2007 Analog Device Inc.
+# Copyright (c) 2007 Analog Device Inc.
#
-# (C) Copyright 2000-2004
+# (C) Copyright 2000-2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
_end = . ;
PROVIDE (end = .);
}
-
#
# U-boot - Makefile
#
-# Copyright (c) 2005-2007 Analog Device Inc.
+# Copyright (c) 2007 Analog Device Inc.
#
-# (C) Copyright 2000-2004
+# (C) Copyright 2000-2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
_end = . ;
PROVIDE (end = .);
}
-
*
* Copyright (c) 2005 blackfin.uclinux.org
*
- * This file is based on
+ * This file is based on
* bf533_serial.h: Definitions for the BlackFin BF533 DSP serial driver.
* Copyright (C) 2003 Bas Vermeulen <bas@buyways.nl>
* BuyWays B.V. (www.buyways.nl)
(R7:5) =[SP++];
RTS;
-/*
+/*
* Invalidate the Entire Data cache by
* clearing DMC[1:0] bits
*/
P0.H = (DMEM_CONTROL >> 16);
R7 =[P0];
-/*
+/*
* Clear the DMC[1:0] bits, All valid bits in the data
* cache are set to the invalid state
*/
CC = P0 < P1(iu);
IF CC JUMP 1b(bp);
-/*
+/*
* If the data crosses a cache line, then we'll be pointing to
* the last cache line, but won't have flushed/invalidated it yet, so do
* one more.
* R0 = Page start
* R1 = Page length (actually, offset into size/prefix tables)
* R3 = sub-bank deposit values
- *
+ *
* The cache has 2 Ways, and 64 sets, so we iterate through
* the sets, accessing the tag for each Way, for our Bank and
* sub-bank, looking for dirty, valid tags that match our
IF !CC JUMP ifskip; /* Skip it if it doesn't match.*/
/* Tag address matches against page, so this is an entry
- * we must flush.
+ * we must flush.
*/
R7 >>= 10; /* Mask off the non-address bits*/
SSYNC;
JUMP ifinished;
-/* This is an external function being called by the user
+/* This is an external function being called by the user
* application through __flush_cache_all. Currently this function
* serves the purpose of flushing all the pending writes in
* in the data cache.
/* This is an internal function to flush all pending
* writes in the cache associated with a particular DCPLB.
- *
+ *
* R0 - page's start address
* R1 - CPLB's data field.
*/
/* The page could be mapped into Bank A or Bank B, depending
* on (a) whether both banks are configured as cache, and
* (b) on whether address bit A[x] is set. x is determined
- * by DCBS in DMEM_CONTROL
+ * by DCBS in DMEM_CONTROL
*/
R2 = 0; /* Default to Bank A (Bank B would be 1)*/
[--SP] = (R7:0);
[--SP] = (P5:0);
-#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
p0.h = hi(SPI_BAUD);
p0.l = lo(SPI_BAUD);
r0.l = CONFIG_SPI_BAUD;
w[p0] = r0.l;
- SSYNC;
+ SSYNC;
#endif
/*
- * PLL_LOCKCNT - how many SCLK Cycles to delay while PLL becomes stable
- */
+ * PLL_LOCKCNT - how many SCLK Cycles to delay while PLL becomes stable
+ */
p0.h = hi(PLL_LOCKCNT);
p0.l = lo(PLL_LOCKCNT);
r0 = 0x300(Z);
ssync;
/*
- * Put SDRAM in self-refresh, incase anything is running
- */
- P2.H = hi(EBIU_SDGCTL);
- P2.L = lo(EBIU_SDGCTL);
- R0 = [P2];
- BITSET (R0, 24);
- [P2] = R0;
- SSYNC;
-
- /*
- * Set PLL_CTL with the value that we calculate in R0
- * - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
- * - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK
- * - [7] = output delay (add 200ps of delay to mem signals)
- * - [6] = input delay (add 200ps of input delay to mem signals)
- * - [5] = PDWN : 1=All Clocks off
- * - [3] = STOPCK : 1=Core Clock off
- * - [1] = PLL_OFF : 1=Disable Power to PLL
- * - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
- * all other bits set to zero
- */
-
- r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */
- r0 = r0 << 9; /* Shift it over, */
- r1 = CONFIG_CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/
- r0 = r1 | r0;
- r1 = CONFIG_PLL_BYPASS; /* Bypass the PLL? */
- r1 = r1 << 8; /* Shift it over */
- r0 = r1 | r0; /* add them all together */
-
- p0.h = hi(PLL_CTL);
- p0.l = lo(PLL_CTL); /* Load the address */
- cli r2; /* Disable interrupts */
+ * Put SDRAM in self-refresh, incase anything is running
+ */
+ P2.H = hi(EBIU_SDGCTL);
+ P2.L = lo(EBIU_SDGCTL);
+ R0 = [P2];
+ BITSET (R0, 24);
+ [P2] = R0;
+ SSYNC;
+
+ /*
+ * Set PLL_CTL with the value that we calculate in R0
+ * - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
+ * - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK
+ * - [7] = output delay (add 200ps of delay to mem signals)
+ * - [6] = input delay (add 200ps of input delay to mem signals)
+ * - [5] = PDWN : 1=All Clocks off
+ * - [3] = STOPCK : 1=Core Clock off
+ * - [1] = PLL_OFF : 1=Disable Power to PLL
+ * - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
+ * all other bits set to zero
+ */
+
+ r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */
+ r0 = r0 << 9; /* Shift it over, */
+ r1 = CONFIG_CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/
+ r0 = r1 | r0;
+ r1 = CONFIG_PLL_BYPASS; /* Bypass the PLL? */
+ r1 = r1 << 8; /* Shift it over */
+ r0 = r1 | r0; /* add them all together */
+
+ p0.h = hi(PLL_CTL);
+ p0.l = lo(PLL_CTL); /* Load the address */
+ cli r2; /* Disable interrupts */
ssync;
- w[p0] = r0.l; /* Set the value */
- idle; /* Wait for the PLL to stablize */
- sti r2; /* Enable interrupts */
+ w[p0] = r0.l; /* Set the value */
+ idle; /* Wait for the PLL to stablize */
+ sti r2; /* Enable interrupts */
check_again:
p0.h = hi(PLL_STAT);
if ! CC jump check_again;
/* Configure SCLK & CCLK Dividers */
- r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
- p0.h = hi(PLL_DIV);
- p0.l = lo(PLL_DIV);
- w[p0] = r0.l;
- ssync;
+ r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
+ p0.h = hi(PLL_DIV);
+ p0.l = lo(PLL_DIV);
+ w[p0] = r0.l;
+ ssync;
/*
- * We now are running at speed, time to set the Async mem bank wait states
+ * We now are running at speed, time to set the Async mem bank wait states
* This will speed up execution, since we are normally running from FLASH.
*/
- p2.h = (EBIU_AMBCTL1 >> 16);
- p2.l = (EBIU_AMBCTL1 & 0xFFFF);
- r0.h = (AMBCTL1VAL >> 16);
- r0.l = (AMBCTL1VAL & 0xFFFF);
- [p2] = r0;
- ssync;
-
- p2.h = (EBIU_AMBCTL0 >> 16);
- p2.l = (EBIU_AMBCTL0 & 0xFFFF);
- r0.h = (AMBCTL0VAL >> 16);
- r0.l = (AMBCTL0VAL & 0xFFFF);
- [p2] = r0;
- ssync;
-
- p2.h = (EBIU_AMGCTL >> 16);
- p2.l = (EBIU_AMGCTL & 0xffff);
- r0 = AMGCTLVAL;
- w[p2] = r0;
- ssync;
+ p2.h = (EBIU_AMBCTL1 >> 16);
+ p2.l = (EBIU_AMBCTL1 & 0xFFFF);
+ r0.h = (AMBCTL1VAL >> 16);
+ r0.l = (AMBCTL1VAL & 0xFFFF);
+ [p2] = r0;
+ ssync;
+
+ p2.h = (EBIU_AMBCTL0 >> 16);
+ p2.l = (EBIU_AMBCTL0 & 0xFFFF);
+ r0.h = (AMBCTL0VAL >> 16);
+ r0.l = (AMBCTL0VAL & 0xFFFF);
+ [p2] = r0;
+ ssync;
+
+ p2.h = (EBIU_AMGCTL >> 16);
+ p2.l = (EBIU_AMGCTL & 0xffff);
+ r0 = AMGCTLVAL;
+ w[p2] = r0;
+ ssync;
/*
* Now, Initialize the SDRAM,
* start with the SDRAM Refresh Rate Control Register
- */
+ */
p0.l = lo(EBIU_SDRRC);
- p0.h = hi(EBIU_SDRRC);
- r0 = mem_SDRRC;
- w[p0] = r0.l;
- ssync;
+ p0.h = hi(EBIU_SDRRC);
+ r0 = mem_SDRRC;
+ w[p0] = r0.l;
+ ssync;
/*
* SDRAM Memory Bank Control Register - bank specific parameters
* Disable self-refresh
*/
P2.H = hi(EBIU_SDGCTL);
- P2.L = lo(EBIU_SDGCTL);
- R0 = [P2];
- BITCLR (R0, 24);
+ P2.L = lo(EBIU_SDGCTL);
+ R0 = [P2];
+ BITCLR (R0, 24);
/*
- * Check if SDRAM is already powered up, if it is, enable self-refresh
- */
+ * Check if SDRAM is already powered up, if it is, enable self-refresh
+ */
p0.h = hi(EBIU_SDSTAT);
p0.l = lo(EBIU_SDSTAT);
r2.l = w[p0];
cc = bittst(r2,3);
if !cc jump skip;
- NOP;
+ NOP;
BITSET (R0, 23);
skip:
[P2] = R0;
- SSYNC;
+ SSYNC;
/* Write in the new value in the register */
- R0.L = lo(mem_SDGCTL);
- R0.H = hi(mem_SDGCTL);
+ R0.L = lo(mem_SDGCTL);
+ R0.H = hi(mem_SDGCTL);
[P2] = R0;
- SSYNC;
+ SSYNC;
nop;
(P5:0) = [SP++];
RETS = [SP++];
ASTAT = [SP++];
RTS;
-
[--SP] = (R7:0);
[--SP] = (P5:0);
-#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
p0.h = hi(SPI_BAUD);
p0.l = lo(SPI_BAUD);
r0.l = CONFIG_SPI_BAUD_INITBLOCK;
w[p0] = r0.l;
- SSYNC;
+ SSYNC;
#endif
/*
- * PLL_LOCKCNT - how many SCLK Cycles to delay while PLL becomes stable
- */
+ * PLL_LOCKCNT - how many SCLK Cycles to delay while PLL becomes stable
+ */
p0.h = hi(PLL_LOCKCNT);
p0.l = lo(PLL_LOCKCNT);
r0 = 0x300(Z);
ssync;
/*
- * Put SDRAM in self-refresh, incase anything is running
- */
- P2.H = hi(EBIU_SDGCTL);
- P2.L = lo(EBIU_SDGCTL);
- R0 = [P2];
- BITSET (R0, 24);
- [P2] = R0;
- SSYNC;
-
- /*
- * Set PLL_CTL with the value that we calculate in R0
- * - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
- * - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK
- * - [7] = output delay (add 200ps of delay to mem signals)
- * - [6] = input delay (add 200ps of input delay to mem signals)
- * - [5] = PDWN : 1=All Clocks off
- * - [3] = STOPCK : 1=Core Clock off
- * - [1] = PLL_OFF : 1=Disable Power to PLL
- * - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
- * all other bits set to zero
- */
-
- r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */
- r0 = r0 << 9; /* Shift it over, */
- r1 = CONFIG_CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/
- r0 = r1 | r0;
- r1 = CONFIG_PLL_BYPASS; /* Bypass the PLL? */
- r1 = r1 << 8; /* Shift it over */
- r0 = r1 | r0; /* add them all together */
-
- p0.h = hi(PLL_CTL);
- p0.l = lo(PLL_CTL); /* Load the address */
- cli r2; /* Disable interrupts */
+ * Put SDRAM in self-refresh, incase anything is running
+ */
+ P2.H = hi(EBIU_SDGCTL);
+ P2.L = lo(EBIU_SDGCTL);
+ R0 = [P2];
+ BITSET (R0, 24);
+ [P2] = R0;
+ SSYNC;
+
+ /*
+ * Set PLL_CTL with the value that we calculate in R0
+ * - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
+ * - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK
+ * - [7] = output delay (add 200ps of delay to mem signals)
+ * - [6] = input delay (add 200ps of input delay to mem signals)
+ * - [5] = PDWN : 1=All Clocks off
+ * - [3] = STOPCK : 1=Core Clock off
+ * - [1] = PLL_OFF : 1=Disable Power to PLL
+ * - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
+ * all other bits set to zero
+ */
+
+ r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */
+ r0 = r0 << 9; /* Shift it over, */
+ r1 = CONFIG_CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/
+ r0 = r1 | r0;
+ r1 = CONFIG_PLL_BYPASS; /* Bypass the PLL? */
+ r1 = r1 << 8; /* Shift it over */
+ r0 = r1 | r0; /* add them all together */
+
+ p0.h = hi(PLL_CTL);
+ p0.l = lo(PLL_CTL); /* Load the address */
+ cli r2; /* Disable interrupts */
ssync;
- w[p0] = r0.l; /* Set the value */
- idle; /* Wait for the PLL to stablize */
- sti r2; /* Enable interrupts */
+ w[p0] = r0.l; /* Set the value */
+ idle; /* Wait for the PLL to stablize */
+ sti r2; /* Enable interrupts */
check_again:
p0.h = hi(PLL_STAT);
if ! CC jump check_again;
/* Configure SCLK & CCLK Dividers */
- r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
- p0.h = hi(PLL_DIV);
- p0.l = lo(PLL_DIV);
- w[p0] = r0.l;
- ssync;
+ r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
+ p0.h = hi(PLL_DIV);
+ p0.l = lo(PLL_DIV);
+ w[p0] = r0.l;
+ ssync;
/*
- * We now are running at speed, time to set the Async mem bank wait states
+ * We now are running at speed, time to set the Async mem bank wait states
* This will speed up execution, since we are normally running from FLASH.
*/
- p2.h = (EBIU_AMBCTL1 >> 16);
- p2.l = (EBIU_AMBCTL1 & 0xFFFF);
- r0.h = (AMBCTL1VAL >> 16);
- r0.l = (AMBCTL1VAL & 0xFFFF);
- [p2] = r0;
- ssync;
-
- p2.h = (EBIU_AMBCTL0 >> 16);
- p2.l = (EBIU_AMBCTL0 & 0xFFFF);
- r0.h = (AMBCTL0VAL >> 16);
- r0.l = (AMBCTL0VAL & 0xFFFF);
- [p2] = r0;
- ssync;
-
- p2.h = (EBIU_AMGCTL >> 16);
- p2.l = (EBIU_AMGCTL & 0xffff);
- r0 = AMGCTLVAL;
- w[p2] = r0;
- ssync;
+ p2.h = (EBIU_AMBCTL1 >> 16);
+ p2.l = (EBIU_AMBCTL1 & 0xFFFF);
+ r0.h = (AMBCTL1VAL >> 16);
+ r0.l = (AMBCTL1VAL & 0xFFFF);
+ [p2] = r0;
+ ssync;
+
+ p2.h = (EBIU_AMBCTL0 >> 16);
+ p2.l = (EBIU_AMBCTL0 & 0xFFFF);
+ r0.h = (AMBCTL0VAL >> 16);
+ r0.l = (AMBCTL0VAL & 0xFFFF);
+ [p2] = r0;
+ ssync;
+
+ p2.h = (EBIU_AMGCTL >> 16);
+ p2.l = (EBIU_AMGCTL & 0xffff);
+ r0 = AMGCTLVAL;
+ w[p2] = r0;
+ ssync;
/*
* Now, Initialize the SDRAM,
* start with the SDRAM Refresh Rate Control Register
- */
+ */
p0.l = lo(EBIU_SDRRC);
- p0.h = hi(EBIU_SDRRC);
- r0 = mem_SDRRC;
- w[p0] = r0.l;
- ssync;
+ p0.h = hi(EBIU_SDRRC);
+ r0 = mem_SDRRC;
+ w[p0] = r0.l;
+ ssync;
/*
* SDRAM Memory Bank Control Register - bank specific parameters
* Disable self-refresh
*/
P2.H = hi(EBIU_SDGCTL);
- P2.L = lo(EBIU_SDGCTL);
- R0 = [P2];
- BITCLR (R0, 24);
+ P2.L = lo(EBIU_SDGCTL);
+ R0 = [P2];
+ BITCLR (R0, 24);
/*
- * Check if SDRAM is already powered up, if it is, enable self-refresh
- */
+ * Check if SDRAM is already powered up, if it is, enable self-refresh
+ */
p0.h = hi(EBIU_SDSTAT);
p0.l = lo(EBIU_SDSTAT);
r2.l = w[p0];
cc = bittst(r2,3);
if !cc jump skip;
- NOP;
+ NOP;
BITSET (R0, 23);
skip:
[P2] = R0;
- SSYNC;
+ SSYNC;
/* Write in the new value in the register */
- R0.L = lo(mem_SDGCTL);
- R0.H = hi(mem_SDGCTL);
+ R0.L = lo(mem_SDGCTL);
+ R0.H = hi(mem_SDGCTL);
[P2] = R0;
- SSYNC;
+ SSYNC;
nop;
-
(P5:0) = [SP++];
(R7:0) = [SP++];
RETS = [SP++];
ASTAT = [SP++];
RTS;
-
sp += 12;
_evt_rst_exit:
- rtn;
+ rtn;
irq_panic:
r0 = IRQ_EVX;
evt_evt7_exit:
RESTORE_CONTEXT
- rti;
+ rti;
.global _evt_evt8
_evt_evt8:
/*
* Note: A change in this file subsequently requires a change in
- * board/$(board_name)/config.mk for a valid u-boot.bin
+ * board/$(board_name)/config.mk for a valid u-boot.bin
*/
#define ASSEMBLY
[ p0 ++ ] = r1;
p0.h = hi(SIC_IWR);
- p0.l = lo(SIC_IWR);
- r0.l = 0x1;
- w[p0] = r0.l;
- SSYNC;
+ p0.l = lo(SIC_IWR);
+ r0.l = 0x1;
+ w[p0] = r0.l;
+ SSYNC;
sp.l = (0xffb01000 & 0xFFFF);
sp.h = (0xffb01000 >> 16);
{
/*
* This array contains a single bit for each line in
- * an NTSC frame.
+ * an NTSC frame.
*/
if ((line <= 18) || (line >= 264 && line <= 281) || (line == 528))
return true;
/* Issues that are common to 0.5, 0.4, and 0.3 silicon */
#if (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_4) || defined(CONFIG_BF_REV_0_3))
#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
- slot1 and store of a P register in slot 2 is not
- supported */
+ slot1 and store of a P register in slot 2 is not
+ supported */
#define ANOMALY_05000105 /* Watchpoint Status Register (WPSTAT) bits are set on
- every corresponding match */
+ every corresponding match */
#define ANOMALY_05000119 /* DMA_RUN bit is not valid after a Peripheral Receive
- Channel DMA stops */
+ Channel DMA stops */
#define ANOMALY_05000122 /* Rx.H can not be used to access 16-bit System MMR
- registers. */
+ registers. */
#define ANOMALY_05000166 /* PPI Data Lengths Between 8 and 16 do not zero out
- upper bits*/
+ upper bits*/
#define ANOMALY_05000167 /* Turning Serial Ports on With External Frame Syncs */
#define ANOMALY_05000180 /* PPI_DELAY not functional in PPI modes with 0 frame
- syncs */
+ syncs */
#define ANOMALY_05000208 /* VSTAT status bit in PLL_STAT register is not
- functional */
+ functional */
#define ANOMALY_05000219 /* NMI event at boot time results in unpredictable
- state */
+ state */
#define ANOMALY_05000229 /* SPI Slave Boot Mode modifies registers */
#define ANOMALY_05000272 /* Certain data cache write through modes fail for
- VDDint <=0.9V */
+ VDDint <=0.9V */
#define ANOMALY_05000273 /* Writes to Synchronous SDRAM memory may be lost */
#define ANOMALY_05000277 /* Writes to a flag data register one SCLK cycle after
- an edge is detected may clear interrupt */
+ an edge is detected may clear interrupt */
#define ANOMALY_05000278 /* Disabling Peripherals with DMA running may cause
- DMA system instability */
+ DMA system instability */
#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is
- not restored */
+ not restored */
#define ANOMALY_05000282 /* Memory DMA corruption with 32-bit data and traffic
- control */
+ control */
#define ANOMALY_05000283 /* A system MMR write is stalled indefinitely when
- killed in a particular stage*/
+ killed in a particular stage*/
#endif
/* These issues only occur on 0.3 or 0.4 BF533 */
#if (defined(CONFIG_BF_REV_0_4) || defined(CONFIG_BF_REV_0_3))
#define ANOMALY_05000099 /* UART Line Status Register (UART_LSR) bits are not
- updated at the same time. */
+ updated at the same time. */
#define ANOMALY_05000158 /* Boot fails when data cache enabled: Data from a Data
- Cache Fill can be corrupted after or during
- Instruction DMA if certain core stalls exist */
+ Cache Fill can be corrupted after or during
+ Instruction DMA if certain core stalls exist */
#define ANOMALY_05000179 /* PPI_COUNT cannot be programmed to 0 in General
- Purpose TX or RX modes */
+ Purpose TX or RX modes */
#define ANOMALY_05000198 /* Failing SYSTEM MMR accesses when stalled by
- preceding memory read */
+ preceding memory read */
#define ANOMALY_05000200 /* SPORT TFS and DT are incorrectly driven during
- inactive channels in certain conditions */
+ inactive channels in certain conditions */
#define ANOMALY_05000202 /* Possible infinite stall with specific dual dag
- situation */
+ situation */
#define ANOMALY_05000215 /* UART TX Interrupt masked erroneously */
#define ANOMALY_05000225 /* Incorrect pulse-width of UART start-bit */
#define ANOMALY_05000227 /* Scratchpad memory bank reads may return incorrect
- data*/
+ data*/
#define ANOMALY_05000230 /* UART Receiver is less robust against Baudrate
- Differences in certain Conditions */
+ Differences in certain Conditions */
#define ANOMALY_05000231 /* UART STB bit incorrectly affects receiver setting */
#define ANOMALY_05000242 /* DF bit in PLL_CTL register does not respond to
- hardware reset */
+ hardware reset */
#define ANOMALY_05000244 /* With instruction cache enabled, a CSYNC or SSYNC or
- IDLE around a Change of Control causes
- unpredictable results */
+ IDLE around a Change of Control causes
+ unpredictable results */
#define ANOMALY_05000245 /* Spurious Hardware Error from an access in the
- shadow of a conditional branch */
+ shadow of a conditional branch */
#define ANOMALY_05000246 /* Data CPLB's should prevent spurious hardware
- errors */
+ errors */
#define ANOMALY_05000253 /* Maximum external clock speed for Timers */
#define ANOMALY_05000255 /* Entering Hibernate Mode with RTC Seconds event
- interrupt not functional */
+ interrupt not functional */
#define ANOMALY_05000257 /* An interrupt or exception during short Hardware
- loops may cause the instruction fetch unit to
- malfunction */
+ loops may cause the instruction fetch unit to
+ malfunction */
#define ANOMALY_05000258 /* Instruction Cache is corrupted when bit 9 and 12 of
- the ICPLB Data registers differ */
+ the ICPLB Data registers differ */
#define ANOMALY_05000260 /* ICPLB_STATUS MMR register may be corrupted */
#define ANOMALY_05000261 /* DCPLB_FAULT_ADDR MMR register may be corrupted */
#define ANOMALY_05000262 /* Stores to data cache may be lost */
#define ANOMALY_05000263 /* Hardware loop corrupted when taking an ICPLB exception */
#define ANOMALY_05000264 /* A Sync instruction (CSYNC, SSYNC) or an IDLE
- instruction will cause an infinite stall in the
- second to last instruction in a hardware loop */
+ instruction will cause an infinite stall in the
+ second to last instruction in a hardware loop */
#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on
- SPORT external receive and transmit clocks. */
+ SPORT external receive and transmit clocks. */
#define ANOMALY_05000269 /* High I/O activity causes the output voltage of the
- internal voltage regulator (VDDint) to increase. */
+ internal voltage regulator (VDDint) to increase. */
#define ANOMALY_05000270 /* High I/O activity causes the output voltage of the
- internal voltage regulator (VDDint) to decrease */
+ internal voltage regulator (VDDint) to decrease */
#endif
/* These issues are only on 0.4 silicon */
#if (defined(CONFIG_BF_REV_0_4))
#define ANOMALY_05000234 /* Incorrect Revision Number in DSPID Register */
#define ANOMALY_05000250 /* Incorrect Bit-Shift of Data Word in Multichannel
- (TDM) */
+ (TDM) */
#endif
/* These issues are only on 0.3 silicon */
#if defined(CONFIG_BF_REV_0_3)
#define ANOMALY_05000183 /* Timer Pin limitations for PPI TX Modes with
- External Frame Syncs */
+ External Frame Syncs */
#define ANOMALY_05000189 /* False Protection Exceptions caused by Speculative
- Instruction or Data Fetches, or by Fetches at the
- boundary of reserved memory space */
+ Instruction or Data Fetches, or by Fetches at the
+ boundary of reserved memory space */
#define ANOMALY_05000193 /* False Flag Pin Interrupts on Edge Sensitive Inputs
- when polarity setting is changed */
+ when polarity setting is changed */
#define ANOMALY_05000194 /* Sport Restarting in specific modes may cause data
- corruption */
+ corruption */
#define ANOMALY_05000199 /* DMA current address shows wrong value during carry
- fix */
+ fix */
#define ANOMALY_05000201 /* Receive frame sync not ignored during active
- frames in sport MCM */
+ frames in sport MCM */
#define ANOMALY_05000203 /* Specific sequence that can cause DMA error or DMA
- stopping */
+ stopping */
#if defined(CONFIG_BF533)
#define ANOMALY_05000204 /* Incorrect data read with write-through cache and
- allocate cache lines on reads only mode */
+ allocate cache lines on reads only mode */
#endif /* CONFIG_BF533 */
#define ANOMALY_05000207 /* Recovery from "brown-out" condition */
#define ANOMALY_05000209 /* Speed-Path in computational unit affects certain
- instructions */
+ instructions */
#define ANOMALY_05000233 /* PPI_FS3 is not driven in 2 or 3 internal Frame
- Sync Transmit Mode */
+ Sync Transmit Mode */
#define ANOMALY_05000271 /* Spontaneous reset of Internal Voltage Regulator */
#endif
#define UART_LCR 0xFFC0040C /* Line Control Register */
#define UART_MCR 0xFFC00410 /* Modem Control Register */
#define UART_LSR 0xFFC00414 /* Line Status Register */
-/* #define UART_MSR 0xFFC00418 *//* Modem Status Register (UNUSED in ADSP-BF532) */
+/* #define UART_MSR 0xFFC00418 */ /* Modem Status Register (UNUSED in ADSP-BF532) */
#define UART_SCR 0xFFC0041C /* SCR Scratch Register */
#define UART_GCTL 0xFFC00424 /* Global Control Register */
#endif
#include <asm/arch-common/def_LPBlackfin.h>
-// Cache & SRAM Memory
+/* Cache & SRAM Memory */
#define pSRAM_BASE_ADDRESS ((volatile void **)SRAM_BASE_ADDRESS)
#define pDMEM_CONTROL ((volatile unsigned long *)DMEM_CONTROL)
#define pDCPLB_STATUS ((volatile unsigned long *)DCPLB_STATUS)
#define pDCPLB_FAULT_ADDR ((volatile void **)DCPLB_FAULT_ADDR)
-/*
-#define MMR_TIMEOUT 0xFFE00010 // Memory-Mapped Register Timeout Register
-*/
#define pDCPLB_ADDR0 ((volatile void **)DCPLB_ADDR0)
#define pDCPLB_ADDR1 ((volatile void **)DCPLB_ADDR1)
#define pDCPLB_ADDR2 ((volatile void **)DCPLB_ADDR2)
#define pDCPLB_DATA14 ((volatile unsigned long *)DCPLB_DATA14)
#define pDCPLB_DATA15 ((volatile unsigned long *)DCPLB_DATA15)
#define pDTEST_COMMAND ((volatile unsigned long *)DTEST_COMMAND)
-/*
-#define DTEST_INDEX 0xFFE00304 // Data Test Index Register
-*/
#define pDTEST_DATA0 ((volatile unsigned long *)DTEST_DATA0)
#define pDTEST_DATA1 ((volatile unsigned long *)DTEST_DATA1)
-/*
-#define DTEST_DATA2 0xFFE00408 // Data Test Data Register
-#define DTEST_DATA3 0xFFE0040C // Data Test Data Register
-*/
#define pIMEM_CONTROL ((volatile unsigned long *)IMEM_CONTROL)
#define pICPLB_STATUS ((volatile unsigned long *)ICPLB_STATUS)
#define pICPLB_FAULT_ADDR ((volatile void **)ICPLB_FAULT_ADDR)
#define pICPLB_DATA14 ((volatile unsigned long *)ICPLB_DATA14)
#define pICPLB_DATA15 ((volatile unsigned long *)ICPLB_DATA15)
#define pITEST_COMMAND ((volatile unsigned long *)ITEST_COMMAND)
-/*
-#define ITEST_INDEX 0xFFE01304 // Instruction Test Index Register
-*/
#define pITEST_DATA0 ((volatile unsigned long *)ITEST_DATA0)
#define pITEST_DATA1 ((volatile unsigned long *)ITEST_DATA1)
-// Event/Interrupt Registers
+/* Event/Interrupt Registers */
#define pEVT0 ((volatile void **)EVT0)
#define pEVT1 ((volatile void **)EVT1)
#define pEVT2 ((volatile void **)EVT2)
#define pIPEND ((volatile unsigned long *)IPEND)
#define pILAT ((volatile unsigned long *)ILAT)
-// Core Timer Registers
+/* Core Timer Registers */
#define pTCNTL ((volatile unsigned long *)TCNTL)
#define pTPERIOD ((volatile unsigned long *)TPERIOD)
#define pTSCALE ((volatile unsigned long *)TSCALE)
#define pTCOUNT ((volatile unsigned long *)TCOUNT)
-// Debug/MP/Emulation Registers
+/* Debug/MP/Emulation Registers */
#define pDSPID ((volatile unsigned long *)DSPID)
#define pDBGCTL ((volatile unsigned long *)DBGCTL)
#define pDBGSTAT ((volatile unsigned long *)DBGSTAT)
#define pEMUDAT ((volatile unsigned long *)EMUDAT)
-// Trace Buffer Registers
+/* Trace Buffer Registers */
#define pTBUFCTL ((volatile unsigned long *)TBUFCTL)
#define pTBUFSTAT ((volatile unsigned long *)TBUFSTAT)
#define pTBUF ((volatile void **)TBUF)
-// Watch Point Control Registers
+/* Watch Point Control Registers */
#define pWPIACTL ((volatile unsigned long *)WPIACTL)
#define pWPIA0 ((volatile void **)WPIA0)
#define pWPIA1 ((volatile void **)WPIA1)
#define pWPDACNT1 ((volatile unsigned long *)WPDACNT1)
#define pWPSTAT ((volatile unsigned long *)WPSTAT)
-// Performance Monitor Registers
+/* Performance Monitor Registers */
#define pPFCTL ((volatile unsigned long *)PFCTL)
#define pPFCNTR0 ((volatile unsigned long *)PFCNTR0)
#define pPFCNTR1 ((volatile unsigned long *)PFCNTR1)
-/*
-#define IPRIO 0xFFE02110 // Core Interrupt Priority Register
-*/
-
#endif /* _CDEF_LPBLACKFIN_H */
CONFIG_MEM_MT48LC64M4A2FB_7E || \
CONFIG_MEM_MT48LC16M8A2TG_75 || \
CONFIG_MEM_MT48LC8M16A2TG_7E || \
- CONFIG_MEM_MT48LC8M32B2B5_7 || \
+ CONFIG_MEM_MT48LC8M32B2B5_7 || \
CONFIG_MEM_MT48LC32M8A2_75)
#if ( CONFIG_SCLK_HZ > 119402985 )
#if (CONFIG_MEM_MT48LC16M16A2TG_75)
/*SDRAM INFORMATION: */
- #define SDRAM_Tref 64 /* Refresh period in milliseconds */
- #define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */
+ #define SDRAM_Tref 64 /* Refresh period in milliseconds */
+ #define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */
#define SDRAM_CL CL_3
#endif
#if (CONFIG_MEM_MT48LC64M4A2FB_7E)
/*SDRAM INFORMATION: */
- #define SDRAM_Tref 64 /* Refresh period in milliseconds */
- #define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */
+ #define SDRAM_Tref 64 /* Refresh period in milliseconds */
+ #define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */
#define SDRAM_CL CL_2
#endif
#if (CONFIG_MEM_MT48LC16M8A2TG_75)
- /*SDRAM INFORMATION: */
- #define SDRAM_Tref 64 /* Refresh period in milliseconds */
- #define SDRAM_NRA 4096 /* Number of row addresses in SDRAM */
- #define SDRAM_CL CL_3
+ /*SDRAM INFORMATION: */
+ #define SDRAM_Tref 64 /* Refresh period in milliseconds */
+ #define SDRAM_NRA 4096 /* Number of row addresses in SDRAM */
+ #define SDRAM_CL CL_3
#endif
#if (CONFIG_MEM_MT48LC32M8A2_75)
- /*SDRAM INFORMATION: */
-#define SDRAM_Tref 64 /* Refresh period in milliseconds */
-#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */
+/*SDRAM INFORMATION: */
+#define SDRAM_Tref 64 /* Refresh period in milliseconds */
+#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */
#define SDRAM_CL CL_3
#endif
#if (CONFIG_MEM_MT48LC8M16A2TG_7E)
/*SDRAM INFORMATION: */
- #define SDRAM_Tref 64 /* Refresh period in milliseconds */
- #define SDRAM_NRA 4096 /* Number of row addresses in SDRAM */
+ #define SDRAM_Tref 64 /* Refresh period in milliseconds */
+ #define SDRAM_NRA 4096 /* Number of row addresses in SDRAM */
#define SDRAM_CL CL_2
#endif
#if (CONFIG_MEM_MT48LC8M32B2B5_7)
/*SDRAM INFORMATION: */
- #define SDRAM_Tref 64 /* Refresh period in milliseconds */
- #define SDRAM_NRA 4096 /* Number of row addresses in SDRAM */
+ #define SDRAM_Tref 64 /* Refresh period in milliseconds */
+ #define SDRAM_NRA 4096 /* Number of row addresses in SDRAM */
#define SDRAM_CL CL_3
#endif
#define CONFIG_STAMP 1
#define CONFIG_BOOTDELAY 5
-#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
+#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
-#define CFG_LONGHELP 1
+#define CFG_LONGHELP 1
#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_LOADADDR 0x01000000 /* default load address */
+#define CONFIG_LOADADDR 0x01000000 /* default load address */
#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux"
-//#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw"
+/* #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" */
#define CONFIG_DRIVER_SMC91111 1
#define CONFIG_SMC91111_BASE 0x20310300
* Boot Mode Set
* Blackfin can support several boot modes
*/
-#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
-#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
-#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
+#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
+#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
+#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
/* Define the boot mode */
#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
-//#define BFIN_BOOT_MODE BF533_SPI_BOOT
+/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
#define CONFIG_PANIC_HANG 1
/* Define where the uboot will be loaded by on-chip boot rom */
#define APP_ENTRY 0x00001000
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 27000000
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL */
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
-#define CONFIG_VCO_MULT 22
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
-#define CONFIG_CCLK_DIV 1
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 27000000
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
+/* 1=CLKIN/2 */
+#define CONFIG_CLKIN_HALF 0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
+/* 1=bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
+/* Values can range from 1-64 */
+#define CONFIG_VCO_MULT 22
+/* CONFIG_CCLK_DIV controls what the core clock divider is */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15 */
-#define CONFIG_SCLK_DIV 5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
-/* Values can range from 2-65535 */
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
-#define CONFIG_SPI_BAUD 2
-#define CONFIG_SPI_BAUD_INITBLOCK 4
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
+/* Values can range from 2-65535 */
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
+#define CONFIG_SPI_BAUD 2
+#define CONFIG_SPI_BAUD_INITBLOCK 4
#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
#endif
#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
+#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
#endif
-#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC16M16A2TG_75 1
+#define CONFIG_MEM_SIZ 32 /* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
+#define CONFIG_MEM_MT48LC16M16A2TG_75 1
#define CONFIG_LOADS_ECHO 1
#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
/* JFFS Partition offset set */
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS 1
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_NUM_BANKS 1
/* 512k reserved for u-boot */
-#define CFG_JFFS2_FIRST_SECTOR 11
+#define CFG_JFFS2_FIRST_SECTOR 11
/*
* Stack sizes
*/
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
#define POLL_MODE 1
#define FLASH_TOT_SECT 40
* I2C settings
* By default PF1 is used as SDA and PF0 as SCL on the Stamp board
*/
-#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
/*
* Software (bit-bang) I2C driver configuration
*/
-#define PF_SCL PF0
-#define PF_SDA PF1
-
-#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
-#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SDA; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SDA; \
- asm("ssync;"); \
- }
-#define I2C_SCL(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SCL; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SCL; \
- asm("ssync;"); \
- }
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CFG_I2C_SPEED 50000
-#define CFG_I2C_SLAVE 0xFE
+#define PF_SCL PF0
+#define PF_SDA PF1
+
+#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
+#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
+#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
+#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
+#define I2C_SDA(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SDA; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SDA; \
+ asm("ssync;"); \
+ }
+#define I2C_SCL(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SCL; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SCL; \
+ asm("ssync;"); \
+ }
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CFG_I2C_SPEED 50000
+#define CFG_I2C_SLAVE 0xFE
#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
-/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
- ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
-#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
- B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
+/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
+#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
+ ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
+#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
+ B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
*/
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0x7BB07BB0
-#define AMBCTL1VAL 0xFFC27BB0
+#define AMGCTLVAL 0xFF
+#define AMBCTL0VAL 0x7BB07BB0
+#define AMBCTL1VAL 0xFFC27BB0
#define CONFIG_VDSP 1
* Boot Mode Set
* Blackfin can support several boot modes
*/
-#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
-#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
-#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
+#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
+#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
+#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
/* Define the boot mode */
#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
-//#define BFIN_BOOT_MODE BF533_SPI_BOOT
+/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
#define CONFIG_PANIC_HANG 1
/*
* Board settings
- *
*/
-#define CONFIG_DRIVER_SMC91111 1
-#define CONFIG_SMC91111_BASE 0x20300300
+#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x20300300
/* FLASH/ETHERNET uses the same address range */
-#define SHARED_RESOURCES 1
+#define SHARED_RESOURCES 1
/* Is I2C bit-banged? */
-#define CONFIG_SOFT_I2C 1
+#define CONFIG_SOFT_I2C 1
/*
* Software (bit-bang) I2C driver configuration
*/
-#define PF_SCL PF3
-#define PF_SDA PF2
+#define PF_SCL PF3
+#define PF_SDA PF2
/*
* Video splash screen support
*/
-#define CONFIG_VIDEO 0
+#define CONFIG_VIDEO 0
-#define CONFIG_VDSP 1
+#define CONFIG_VDSP 1
/*
* Clock settings
- *
*/
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 11059200
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL */
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
-#define CONFIG_VCO_MULT 36
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
-#define CONFIG_CCLK_DIV 1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15 */
-#define CONFIG_SCLK_DIV 5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
-/* Values can range from 2-65535 */
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
-#define CONFIG_SPI_BAUD 2
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 11059200
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
+/* 1=CLKIN/2 */
+#define CONFIG_CLKIN_HALF 0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
+/* 1=bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
+/* Values can range from 1-64 */
+#define CONFIG_VCO_MULT 36
+/* CONFIG_CCLK_DIV controls what the core clock divider is */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
+/* Values can range from 2-65535 */
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
+#define CONFIG_SPI_BAUD 2
#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
-#define CONFIG_SPI_BAUD_INITBLOCK 4
+#define CONFIG_SPI_BAUD_INITBLOCK 4
#endif
-
/*
* Network settings
- *
*/
#if (CONFIG_DRIVER_SMC91111)
#endif
/* network support */
-#define CONFIG_IPADDR 192.168.0.15
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.2
-#define CONFIG_HOSTNAME STAMP
-#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
+#define CONFIG_IPADDR 192.168.0.15
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP 192.168.0.2
+#define CONFIG_HOSTNAME STAMP
+#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
/* To remove hardcoding and enable MAC storage in EEPROM */
-/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
#endif /* CONFIG_DRIVER_SMC91111 */
/*
* Flash settings
- *
*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH_CFI_AMD_RESET
-#define CFG_FLASH_BASE 0x20000000
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+#define CFG_FLASH_BASE 0x20000000
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR 0x20004000
-#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR 0x20004000
+#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
-#define CFG_ENV_IS_IN_EEPROM 1
-#define CFG_ENV_OFFSET 0x4000
-#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */
+#define CFG_ENV_IS_IN_EEPROM 1
+#define CFG_ENV_OFFSET 0x4000
+#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */
#endif
-#define CFG_ENV_SIZE 0x2000
-#define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
+#define CFG_ENV_SIZE 0x2000
+#define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
#define ENV_IS_EMBEDDED
-#define CFG_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */
+#define CFG_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */
#define CFG_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
/* JFFS Partition offset set */
#define CFG_JFFS2_FIRST_BANK 0
#define CFG_JFFS2_NUM_BANKS 1
/* 512k reserved for u-boot */
-#define CFG_JFFS2_FIRST_SECTOR 11
+#define CFG_JFFS2_FIRST_SECTOR 11
/*
* following timeouts shall be used once the
* Flash real protection is enabled
*/
-#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
-#define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
+#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
+#define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
/*
* SDRAM settings & memory map
- *
*/
-#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
+#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
#define CONFIG_MEM_MT48LC64M4A2FB_7E 1
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
-#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
+#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#endif
-#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_BASE 0x00000000
#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024)
#define CFG_MEMTEST_END (CFG_MAX_RAM_SIZE - 0x80000 - 1)
#define CONFIG_LOADADDR 0x01000000
-#define CFG_LOAD_ADDR CONFIG_LOADADDR
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#define CFG_LOAD_ADDR CONFIG_LOADADDR
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - 0x40000)
-#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
-#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
+#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
/* Check to make sure everything fits in SDRAM */
#if ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) > CFG_MAX_RAM_SIZE)
#endif
#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
#endif
#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
+#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
#endif
#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
#undef CONFIG_SPI_FLASH_FAST_READ
#endif
#endif
+
/*
* Command settings
- *
*/
-#define CFG_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
+#define CFG_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
-#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
+#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
#endif
- /* configuration lookup from the BOOTP/DHCP server, */
- /* but not try to load any image using TFTP */
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
+/* configuration lookup from the BOOTP/DHCP server, */
+/* but not try to load any image using TFTP */
+
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
-#define CONFIG_BOOTCOMMAND "run ramboot"
+#define CONFIG_BOOTCOMMAND "run ramboot"
#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
-#define CONFIG_BOOTCOMMAND "eeprom read 0x1000000 0x100000 0x180000;icache on;dcache on;bootm 0x1000000"
+#define CONFIG_BOOTCOMMAND "eeprom read 0x1000000 0x100000 0x180000;icache on;dcache on;bootm 0x1000000"
#endif
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
#if (CONFIG_DRIVER_SMC91111)
-#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \
- CFG_CMD_PING | \
- CFG_CMD_ELF | \
- CFG_CMD_CACHE | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_EEPROM | \
- CFG_CMD_DATE)
+#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \
+ CFG_CMD_PING | \
+ CFG_CMD_ELF | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DATE)
#else
-#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \
- CFG_CMD_ELF | \
- CFG_CMD_CACHE | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_EEPROM | \
- CFG_CMD_DATE)
-
+#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \
+ CFG_CMD_ELF | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DATE)
#endif
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#if (CONFIG_DRIVER_SMC91111)
#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
- "$(rootpath) console=ttyBF0,57600\0" \
- "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
- "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
- "ramboot=tftpboot $(loadaddr) linux; " \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
+ "$(rootpath) console=ttyBF0,57600\0" \
+ "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
+ "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
+ "ramboot=tftpboot $(loadaddr) linux; " \
"run ramargs;run addip;bootelf\0" \
- "nfsboot=tftpboot $(loadaddr) linux; " \
+ "nfsboot=tftpboot $(loadaddr) linux; " \
"run nfsargs;run addip;bootelf\0" \
- "flashboot=bootm 0x20100000\0" \
- "update=tftpboot $(loadaddr) u-boot.bin; " \
- "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
- "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
- ""
+ "flashboot=bootm 0x20100000\0" \
+ "update=tftpboot $(loadaddr) u-boot.bin; " \
+ "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
+ "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
+ ""
#else
#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "flashboot=bootm 0x20100000\0" \
- ""
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "flashboot=bootm 0x20100000\0" \
+ "
#endif
#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
/*
* Console settings
- *
*/
-#define CONFIG_BAUDRATE 57600
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_BAUDRATE 57600
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
#if (BFIN_CPU == ADSP_BF531)
-#define CFG_PROMPT "serial_bf531> " /* Monitor Command Prompt */
+#define CFG_PROMPT "serial_bf531> " /* Monitor Command Prompt */
#elif (BFIN_CPU == ADSP_BF532)
-#define CFG_PROMPT "serial_bf532> " /* Monitor Command Prompt */
+#define CFG_PROMPT "serial_bf532> " /* Monitor Command Prompt */
#else
-#define CFG_PROMPT "serial_bf533> " /* Monitor Command Prompt */
+#define CFG_PROMPT "serial_bf533> " /* Monitor Command Prompt */
#endif
#else
#if (BFIN_CPU == ADSP_BF531)
-#define CFG_PROMPT "bf531> " /* Monitor Command Prompt */
+#define CFG_PROMPT "bf531> " /* Monitor Command Prompt */
#elif (BFIN_CPU == ADSP_BF532)
-#define CFG_PROMPT "bf532> " /* Monitor Command Prompt */
+#define CFG_PROMPT "bf532> " /* Monitor Command Prompt */
#else
-#define CFG_PROMPT "bf533> " /* Monitor Command Prompt */
+#define CFG_PROMPT "bf533> " /* Monitor Command Prompt */
#endif
#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_LOADS_ECHO 1
+#define CONFIG_LOADS_ECHO 1
/*
* I2C settings
*/
#if (CONFIG_SOFT_I2C)
-#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
-#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SDA; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SDA; \
- asm("ssync;"); \
- }
-#define I2C_SCL(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SCL; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SCL; \
- asm("ssync;"); \
- }
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CFG_I2C_SPEED 50000
-#define CFG_I2C_SLAVE 0xFE
+#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
+#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
+#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
+#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
+#define I2C_SDA(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SDA; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SDA; \
+ asm("ssync;"); \
+ }
+#define I2C_SCL(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SCL; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SCL; \
+ asm("ssync;"); \
+ }
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CFG_I2C_SPEED 50000
+#define CFG_I2C_SLAVE 0xFE
#endif /* CONFIG_SOFT_I2C */
/*
*/
/* Enabled below option for CF support */
-/* #define CONFIG_STAMP_CF 1 */
+/* #define CONFIG_STAMP_CF 1 */
#if defined(CONFIG_STAMP_CF) && (CONFIG_COMMANDS & CFG_CMD_IDE)
-#define CONFIG_MISC_INIT_R 1
-#define CONFIG_DOS_PARTITION 1
+#define CONFIG_MISC_INIT_R 1
+#define CONFIG_DOS_PARTITION 1
/*
* IDE/ATA stuff
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-#define CFG_ATA_BASE_ADDR 0x20200000
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR 0x20200000
+#define CFG_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
+#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
-#define CFG_ATA_STRIDE 2
+#define CFG_ATA_STRIDE 2
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_HZ 1000 /* 1ms time tick */
+#define CFG_HZ 1000 /* 1ms time tick */
-#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
+#define CFG_BOOTM_LEN 0x4000000/* Large Image Length, set to 64 Meg */
-#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
+#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
#define CONFIG_SPI
#ifdef CONFIG_VIDEO
#if (CONFIG_VIDEO)
-#define CONFIG_SPLASH_SCREEN 1
-#define CONFIG_SILENT_CONSOLE 1
+#define CONFIG_SPLASH_SCREEN 1
+#define CONFIG_SILENT_CONSOLE 1
#else
#undef CONFIG_VIDEO
#endif
/*
* FLASH organization and environment definitions
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */
/* 0xFF, 0xBBC3BBc3, 0x99B39983 */
-/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \
- B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
-#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \
- B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
+/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
+#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \
+ B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
+#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \
+ B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
*/
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0xBBC3BBC3
-#define AMBCTL1VAL 0x99B39983
-#define CF_AMBCTL1VAL 0x99B3ffc2
+#define AMGCTLVAL 0xFF
+#define AMBCTL0VAL 0xBBC3BBC3
+#define AMBCTL1VAL 0x99B39983
+#define CF_AMBCTL1VAL 0x99B3ffc2
#ifdef CONFIG_VDSP
#define ET_EXEC_VDSP 0x8
#define VDSP_ENTRY_ADDR 0xFFA00000
#endif
-
#endif
* to the Free Software Foundation, Inc.,
* 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-
-
-
.align 2
.globl _memcpy_ASM;
projects / project / bcm63xx / u-boot.git / commitdiff