This adds support for the TP-Link TL-WR710N v2.1. It is basically a
re-issue of the v1.2.
Specifications:
SoC: Atheros AR9331
CPU: 400 MHz
Flash: 8 MiB
RAM: 32 MiB
WiFi: 2.4 GHz b/g/n
Ethernet: 2x 100M ports
USB: 1x 2.0
The only difference from the v1 is the TP-Link hardware ID/revision.
Attention:
The TL-WR710N v2.0 (!) has only 4 MB flash and cannot be flashed with
this image. It has a different TPLINK_HWREV, so accidental flashing
of the factory image should be impossible without additional measures.
Unfortunately, the v2.0 in ar71xx has the same board name, so sysupgrade
from ar71xx v2.0 into ath79 v1/v2.1 will not be prevented, but will brick
the device.
Flashing instruction:
Upload the factory image via the OEM firmware GUI upgrade mechanism.
Further notes:
To make implementation easier if somebody desires to port the 4M v2.0,
this already creates two DTSI files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Fabian Eppig <fabian@eppig.de>
(backported from
eb531337a779a48a2d17bc66f0d222325d6c1563)
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9331_tplink_tl-wr710n.dtsi"
+
+&spi {
+ status = "okay";
+
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition@0 {
+ reg = <0x0 0x20000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ partition@20000 {
+ compatible = "tplink,firmware";
+ reg = <0x20000 0x7d0000>;
+ label = "firmware";
+ };
+
+ art: partition@7f0000 {
+ reg = <0x7f0000 0x10000>;
+ label = "art";
+ read-only;
+ };
+ };
+ };
+};
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-#include "ar9331.dtsi"
+#include "ar9331_tplink_tl-wr710n-8m.dtsi"
/ {
model = "TP-Link TL-WR710N v1";
compatible = "tplink,tl-wr710n-v1", "qca,ar9331";
-
- aliases {
- serial0 = &uart;
- led-boot = &led_system;
- led-failsafe = &led_system;
- led-running = &led_system;
- led-upgrade = &led_system;
- };
-
- keys {
- compatible = "gpio-keys-polled";
- poll-interval = <20>;
-
- reset {
- label = "reset";
- linux,code = <KEY_RESTART>;
- gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
-
- led_system: system {
- label = "tl-wr710n:green:system";
- gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
- };
- };
-
- reg_usb_vbus: regulator {
- compatible = "regulator-fixed";
- regulator-name = "usb_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
-};
-
-&spi {
- status = "okay";
- num-cs = <1>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <25000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- uboot: partition@0 {
- reg = <0x0 0x20000>;
- label = "u-boot";
- read-only;
- };
-
- firmware: partition@20000 {
- compatible = "tplink,firmware";
- reg = <0x20000 0x7d0000>;
- label = "firmware";
- };
-
- art: partition@7f0000 {
- reg = <0x7f0000 0x10000>;
- label = "art";
- read-only;
- };
- };
- };
-};
-
-ð0 {
- status = "okay";
-
- mtd-mac-address = <&uboot 0x1fc00>;
-
- gmac-config {
- device = <&gmac>;
-
- switch-phy-addr-swap = <0>;
- switch-phy-swap = <0>;
- };
-};
-
-ð1 {
- status = "okay";
-
- mtd-mac-address = <&uboot 0x1fc00>;
- mtd-mac-address-increment = <(-1)>;
-};
-
-&uart {
- status = "okay";
-};
-
-&usb {
- dr_mode = "host";
- vbus-supply = <®_usb_vbus>;
- status = "okay";
-};
-
-&usb_phy {
- status = "okay";
-};
-
-&wmac {
- status = "okay";
- mtd-cal-data = <&art 0x1000>;
- mtd-mac-address = <&uboot 0x1fc00>;
};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "ar9331_tplink_tl-wr710n-8m.dtsi"
+
+/ {
+ model = "TP-Link TL-WR710N v2.1";
+ compatible = "tplink,tl-wr710n-v2.1", "qca,ar9331";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9331.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart;
+ led-boot = &led_system;
+ led-failsafe = &led_system;
+ led-running = &led_system;
+ led-upgrade = &led_system;
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_system: system {
+ label = "tl-wr710n:green:system";
+ gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_usb_vbus: regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ mtd-mac-address = <&uboot 0x1fc00>;
+
+ gmac-config {
+ device = <&gmac>;
+
+ switch-phy-addr-swap = <0>;
+ switch-phy-swap = <0>;
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ mtd-mac-address = <&uboot 0x1fc00>;
+ mtd-mac-address-increment = <(-1)>;
+};
+
+&gpio {
+ status = "okay";
+};
+
+&uart {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+
+ dr_mode = "host";
+ vbus-supply = <®_usb_vbus>;
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&uboot 0x1fc00>;
+};
endef
TARGET_DEVICES += tplink_tl-wr710n-v1
+define Device/tplink_tl-wr710n-v2.1
+ $(Device/tplink-8mlzma)
+ ATH_SOC := ar9331
+ DEVICE_TITLE := TP-Link TL-WR710N v2.1
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb-chipidea2 kmod-usb-ledtrig-usbport
+ TPLINK_HWID := 0x07100002
+ TPLINK_HWREV := 0x2
+ SUPPORTED_DEVICES += tl-wr710n
+endef
+TARGET_DEVICES += tplink_tl-wr710n-v2.1
+
define Device/tplink_tl-wr842n-v1
$(Device/tplink-8m)
ATH_SOC := ar7241
projects / openwrt / staging / adrian.git / commitdiff