rt2x00 still needs some patching as the radio doesn't come to life.
Installation via webflash.
[juhosg: fix whitespace issues, remove rt305x_register_usb
from machine setup because the board has no USB port]
Signed-off-by: Mikko Hissa <mikko.hissa@uta.fi>
SVN-Revision: 33205
argus-atp52b)
status_led="argus-atp52b:green:run"
;;
- dir-300-b1 | dir-600-b1 | dir-600-b2 | dir-620-a1)
+ dir-300-b1 | dir-600-b1 | dir-600-b2 | dir-615-h1 | dir-620-a1)
status_led="d-link:green:status"
;;
dap-1350)
all5002 | \
argus-atp52b | \
bc2 | \
+ dir-615-h1 | \
dir-620-a1 | \
esr-9753 | \
fonera20n | \
ucidef_set_led_default "wan" "WAN LED (amber)" "d-link:amber:wan" "1"
set_wifi_led "rt2800pci-phy0::radio"
;;
+ dir-615-h1)
+ ucidef_set_led_default "status" "Status LED (amber)" "d-link:amber:status" "0"
+ set_wifi_led "rt2800pci-phy0::radio"
+ ;;
esr-9753)
set_wifi_led "rt2800pci-phy0::radio"
;;
case $board in
all0256n | \
all5002 | \
+ dir-615-h1 | \
wl-330n)
ucidef_set_interface_lan "eth0.1"
;;
case $board in
all0256n | \
- all5002)
+ all5002 | \
+ dir-615-h1)
lan_mac=$(ramips_get_mac_binary factory 40)
;;
3g-6200n | \
ifconfig eth0 hw ether $mac 2>/dev/null
;;
all0256n |\
- all5002 | \
+ all5002 |\
+ dir-615-h1 |\
fonera20n |\
hw550-3g |\
nbg-419n |\
*"DIR-620 A1")
name="dir-620-a1"
;;
+ *"DIR-615 H1")
+ name="dir-615-h1"
+ ;;
*"DAP-1350")
name="dap-1350"
;;
dir-300-b1 | \
dir-600-b1 | \
dir-600-b2 | \
+ dir-615-h1 | \
dir-620-a1 | \
dap-1350 | \
esr-9753 | \
/* RT3352 based machines */
RAMIPS_MACH_ALL5002, /* Allnet ALL5002 */
+ RAMIPS_MACH_DIR_615_H1,
/* RT3662 based machines */
RAMIPS_MACH_RT_N56U, /* Asus RT-N56U */
bool "Allnet ALL0256N support"
select RALINK_DEV_GPIO_BUTTONS
select RALINK_DEV_GPIO_LEDS
-
+
config RT305X_MACH_ALL5002
bool "Allnet ALL5002 support"
select RALINK_DEV_GPIO_BUTTONS
select RALINK_DEV_GPIO_BUTTONS
select RALINK_DEV_GPIO_LEDS
+config RT305X_MACH_DIR_615_H1
+ bool "D-Link DIR-615 H1 board support"
+ select RALINK_DEV_GPIO_BUTTONS
+ select RALINK_DEV_GPIO_LEDS
+
config RT305X_MACH_DAP_1350
bool "D-Link DAP-1350 board support"
select RALINK_DEV_GPIO_BUTTONS
obj-$(CONFIG_RT305X_MACH_ALL0256N) += mach-all0256n.o
obj-$(CONFIG_RT305X_MACH_ALL5002) += mach-all5002.o
obj-$(CONFIG_RT305X_MACH_DIR_300_REVB) += mach-dir-300-revb.o
+obj-$(CONFIG_RT305X_MACH_DIR_615_H1) += mach-dir-615-h1.o
obj-$(CONFIG_RT305X_MACH_DAP_1350) += mach-dap-1350.o
obj-$(CONFIG_RT305X_MACH_ESR_9753) += mach-esr-9753.o
obj-$(CONFIG_RT305X_MACH_F5D8235_V2) += mach-f5d8235-v2.o
--- /dev/null
+/*
+ * D-Link DIR-615 H1
+ *
+ * Copyright (C) 2012 Mikko Hissa <mikko.hissa@uta.fi>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/mach-ralink/machine.h>
+#include <asm/mach-ralink/dev-gpio-buttons.h>
+#include <asm/mach-ralink/dev-gpio-leds.h>
+#include <asm/mach-ralink/rt305x.h>
+#include <asm/mach-ralink/rt305x_regs.h>
+
+#include "devices.h"
+
+#define DIR_615_H1_GPIO_LED_WAN_AMBER 12 /* active low */
+#define DIR_615_H1_GPIO_LED_WAN_GREEN 13 /* active low */
+#define DIR_615_H1_GPIO_LED_WPS_BLUE 14 /* active low */
+
+#define DIR_615_H1_GPIO_LED_STATUS_AMBER 7
+#define DIR_615_H1_GPIO_LED_STATUS_GREEN 9
+
+#define DIR_615_H1_GPIO_BUTTON_RESET 10 /* active low */
+#define DIR_615_H1_GPIO_BUTTON_WPS 0 /* active low */
+
+#define DIR_615_H1_KEYS_POLL_INTERVAL 20
+#define DIR_615_H1_KEYS_DEBOUNCE_INTERVAL (3 * DIR_615_H1_KEYS_POLL_INTERVAL)
+
+static struct gpio_led dir_615_h1_leds_gpio[] __initdata = {
+ {
+ .name = "d-link:amber:status",
+ .gpio = DIR_615_H1_GPIO_LED_STATUS_AMBER,
+ }, {
+ .name = "d-link:green:status",
+ .gpio = DIR_615_H1_GPIO_LED_STATUS_GREEN,
+ }, {
+ .name = "d-link:amber:wan",
+ .gpio = DIR_615_H1_GPIO_LED_WAN_AMBER,
+ .active_low = 1,
+ }, {
+ .name = "d-link:green:wan",
+ .gpio = DIR_615_H1_GPIO_LED_WAN_GREEN,
+ .active_low = 1,
+ }, {
+ .name = "d-link:blue:wps",
+ .gpio = DIR_615_H1_GPIO_LED_WPS_BLUE,
+ .active_low = 1,
+ }
+};
+
+static struct gpio_keys_button dir_615_h1_gpio_buttons[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = DIR_615_H1_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = DIR_615_H1_GPIO_BUTTON_RESET,
+ .active_low = 1,
+ }, {
+ .desc = "wps",
+ .type = EV_KEY,
+ .code = KEY_WPS_BUTTON,
+ .debounce_interval = DIR_615_H1_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = DIR_615_H1_GPIO_BUTTON_WPS,
+ .active_low = 1,
+ }
+};
+
+const struct flash_platform_data dir615h1_flash = {
+ .type = "mx25l3205d",
+};
+
+struct spi_board_info dir615h1_spi_slave_info[] __initdata = {
+ {
+ .modalias = "m25p80",
+ .platform_data = &dir615h1_flash,
+ .irq = -1,
+ .max_speed_hz = 10000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ },
+};
+
+static void __init dir615h1_init(void)
+{
+ rt305x_gpio_init(RT305X_GPIO_MODE_GPIO << RT305X_GPIO_MODE_UART0_SHIFT);
+ rt305x_register_spi(dir615h1_spi_slave_info,
+ ARRAY_SIZE(dir615h1_spi_slave_info));
+ rt305x_esw_data.vlan_config = RT305X_ESW_VLAN_CONFIG_LLLLW;
+ rt305x_register_ethernet();
+ ramips_register_gpio_leds(-1, ARRAY_SIZE(dir_615_h1_leds_gpio),
+ dir_615_h1_leds_gpio);
+ ramips_register_gpio_buttons(-1, DIR_615_H1_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(dir_615_h1_gpio_buttons),
+ dir_615_h1_gpio_buttons);
+ rt305x_register_wifi();
+ rt305x_register_wdt();
+}
+
+MIPS_MACHINE(RAMIPS_MACH_DIR_615_H1, "DIR-615-H1", "D-Link DIR-615 H1",
+ dir615h1_init);
$(call BuildFirmware/Generic/initramfs,$(1),$(2),$(call mkcmdline,$(3),ttyS1,57600) $(call mkmtd/phys,$(mtdlayout_dir300b1)),$(mtd_dir300b1_kernel_part_size),$(mtd_dir300b1_rootfs_part_size))
endef
+mtdlayout_dir615h1=192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),2880k(rootfs),3776k@0x50000(firmware)
+define BuildFirmware/DIR615H1
+ $(call BuildFirmware/Generic,$(1),$(2),$(call mkcmdline,$(3),$(4),$(5)) $(call mkmtd/$(6),$(mtdlayout_dir615h1)),917504,2949120)
+ mkdir615h1 -e $(call sysupname,$(1),$(2)) \
+ -o $(call imgname,$(1),$(2))-factory.bin
+endef
+
+define BuildFirmware/DIR615H1/initramfs
+ $(call BuildFirmware/Generic/initramfs,$(1),$(2),$(call mkcmdline,$(3),$(4),$(5)) $(call mkmtd/$(6),$(mtdlayout_dir615h1)))
+endef
+
mtdlayout_dap1350=192k(u-boot)ro,64k(devdata)ro,192k(devconf)ro,256k(devlang)ro,1088k(kernel),6400k(rootfs),7488k@0xb0000(firmware)
mtd_dap1350_kernel_part_size=1114112
mtd_dap1350_rootfs_part_size=6553600
$(call Image/Build/Template/$(fs_squash)/$(1),DIR620A1,dir-620-a1,DIR-620-A1)
endef
+define Image/Build/Profile/DIR615H1
+ $(call Image/Build/Template/$(fs_squash)/$(1),DIR615H1,dir-615-h1,DIR-615-H1,ttyS1,57600,spi)
+endef
+
define Image/Build/Profile/DAP1350
$(call Image/Build/Template/$(fs_squash)/$(1),DAP1350,dap-1350,DAP-1350,RT3052-AP-DAP1350-3)
endef
$(call Image/Build/Profile/ARGUS_ATP52B,$(1))
$(call Image/Build/Profile/BC2,$(1))
$(call Image/Build/Profile/DIR300B1,$(1))
+ $(call Image/Build/Profile/DIR615H1,$(1))
$(call Image/Build/Profile/DAP1350,$(1))
$(call Image/Build/Profile/ESR9753,$(1))
$(call Image/Build/Profile/F5D8235V2,$(1))
CONFIG_RT305X_MACH_ARGUS_ATP52B=y
CONFIG_RT305X_MACH_BC2=y
CONFIG_RT305X_MACH_DIR_300_REVB=y
+CONFIG_RT305X_MACH_DIR_615_H1=y
CONFIG_RT305X_MACH_DAP_1350=y
CONFIG_RT305X_MACH_ESR_9753=y
CONFIG_RT305X_MACH_F5D8235_V2=y
projects / openwrt / staging / jow.git / commitdiff