ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD

This board has been supported in the ar71xx.

Links:
* https://mikrotik.com/product/RB912UAG-2HPnD
* https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb912uag-2hpnd

This also supports the 5GHz flavour of the board.

Hardware:
* SoC: Atheros AR9342,
* RAM: DDR 64MB,
* SPI NOR: 64KB,
* NAND: 128MB,
* Ethernet: x1 10/100/1000 port with passive POE in,
* Wi-Fi: 802.11 b/g/n,
* PCIe,
* USB: 2.0 EHCI controller, connected to mPCIe slot and a Type-A
  port -- both can be used for LTE modem, but only one can be
  used at any time.
* LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED,
  Ethernet phy LED,
* Button,
* Beeper.

Not working:
* Button: it shares gpio line 15 with NAND ALE and NAND IO7,
  and current drivers doesn't easily support this configuration,
* Beeper: it is connected to bit 5 of a serial shift register
  (tested with sysfs led trigger timer). But kmod-gpio-beeper
  doesn't work -- we left this as is for now.

Flashing:
* Use the RouterBOARD Reset button to enable TFTP netboot,
boot kernel and initramfs and then perform sysupgrade.
* From ar71xx OpenWrt firmware run:
  $ sysupgrade -F /tmp/<sysupgrade.bin>
For more info see: https://openwrt.org/toh/mikrotik/common.

Co-Developed-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
(cherry-picked from commit 695a1cd53ca52c678b3f837deb1bf30204285360)

diff --git a/target/linux/ath79/dts/ar9342_mikrotik_routerboard-912uag-2hpnd.dts b/target/linux/ath79/dts/ar9342_mikrotik_routerboard-912uag-2hpnd.dts
new file mode 100644 (file)
index 0000000..cc5553a
--- /dev/null
+++ b/target/linux/ath79/dts/ar9342_mikrotik_routerboard-912uag-2hpnd.dts
@@ -0,0 +1,212 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ar9344.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "mikrotik,routerboard-912uag-2hpnd", "qca,ar9342";
+       model = "MikroTik RouterBOARD 912UAG-2HPnD";
+
+       aliases {
+                led-boot = &led_power;
+                led-failsafe = &led_power;
+                led-running = &led_power;
+                led-upgrade = &led_power;
+        };
+
+       gpio_latch: gpio_latch {
+               compatible = "gpio-latch";
+               gpio-controller;
+               #gpio-cells = <2>;
+               gpios = <&gpio 0 GPIO_ACTIVE_HIGH>,
+                       <&gpio 1 GPIO_ACTIVE_HIGH>,
+                       <&gpio 2 GPIO_ACTIVE_HIGH>,
+                       <&gpio 3 GPIO_ACTIVE_HIGH>,
+                       <0>, /* Not connected */
+                       <&gpio 13 GPIO_ACTIVE_HIGH>,
+                       <&gpio 14 GPIO_ACTIVE_HIGH>,
+                       <&gpio 15 GPIO_ACTIVE_HIGH>,
+                       <&gpio 11 GPIO_ACTIVE_LOW>; /* Latch Enable */
+       };
+
+       nand_gpio {
+               compatible = "mikrotik,rb91x-nand";
+
+               gpios = <&gpio_latch 3 GPIO_ACTIVE_HIGH>, /* Read */
+                       <&gpio 4 GPIO_ACTIVE_HIGH>,       /* Ready (RDY) */
+                       <&gpio_latch 5 GPIO_ACTIVE_LOW>,  /* Chip Enable (nCE) */
+                       <&gpio_latch 6 GPIO_ACTIVE_HIGH>, /* Command Latch Enable (CLE) */
+                       <&gpio_latch 7 GPIO_ACTIVE_HIGH>, /* Address Latch Enable (ALE) */
+                       <&gpio 12 GPIO_ACTIVE_LOW>,       /* Read/Write Enable (nRW) */
+                       <&gpio_latch 8 GPIO_ACTIVE_LOW>;  /* Latch Enable (nLE) */
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "booter";
+                               reg = <0x0 0x0040000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "kernel";
+                               reg = <0x0040000 0x03c0000>;
+                       };
+
+                       partition@400000 {
+                               label = "ubi";
+                               reg = <0x0400000 0x7c00000>;
+                       };
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_power: power {
+                       label = "green:power";
+                       gpios = <&gpio_latch 1 GPIO_ACTIVE_HIGH>;
+                       default-state = "on";
+               };
+
+               user {
+                       label = "green:user";
+                       gpios = <&gpio_latch 2 GPIO_ACTIVE_HIGH>;
+               };
+
+               led1 {
+                       label = "green:led1";
+                       gpios = <&ssr 0 GPIO_ACTIVE_HIGH>;
+               };
+
+               led2 {
+                       label = "green:led2";
+                       gpios = <&ssr 1 GPIO_ACTIVE_HIGH>;
+               };
+
+               led3 {
+                       label = "green:led3";
+                       gpios = <&ssr 2 GPIO_ACTIVE_HIGH>;
+               };
+
+               led4 {
+                       label = "green:led4";
+                       gpios = <&ssr 3 GPIO_ACTIVE_HIGH>;
+               };
+
+               led5 {
+                       label = "green:led5";
+                       gpios = <&ssr 4 GPIO_ACTIVE_HIGH>;
+               };
+       };
+
+       gpio-export {
+               compatible = "gpio-export";
+
+               usb_power {
+                       gpio-export,name = "power-usb";
+                       gpio-export,output = <1>;
+                       gpios = <&ssr 6 GPIO_ACTIVE_HIGH>;
+               };
+
+               pcie_power {
+                       gpio-export,name = "power-pcie";
+                       gpio-export,output = <0>;
+                       gpios = <&ssr 7 GPIO_ACTIVE_HIGH>;
+               };
+       };
+};
+
+&spi {
+       status = "okay";
+
+       compatible = "qca,ar7100-spi";
+
+       cs-gpios = <0>, <&gpio_latch 0 GPIO_ACTIVE_LOW>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <50000000>;
+
+               partitions {
+                       compatible = "mikrotik,routerboot-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "routerboot";
+                               reg = <0x0 0x0>;
+                               read-only;
+                       };
+
+                       hard_config: hard_config {
+                               read-only;
+                       };
+
+                       bios {
+                               size = <0x1000>;
+                               read-only;
+                       };
+
+                       soft_config {
+                       };
+               };
+       };
+
+       ssr: ssr@1 {
+               compatible = "fairchild,74hc595";
+               gpio-controller;
+               #gpio-cells = <2>;
+               registers-number = <1>;
+               reg = <1>;
+               spi-max-frequency = <50000000>;
+       };
+};
+
+&mdio0 {
+       status = "okay";
+
+       phy-mask = <0>;
+
+       phy0: ethernet-phy@0 {
+               reg = <0>;
+       };
+};
+
+&eth0 {
+       status = "okay";
+
+       phy-mode = "rgmii-id";
+       phy-handle = <&phy0>;
+       pll-data = <0x02000000 0x00000101 0x00001313>;
+
+       gmac-config {
+               device = <&gmac>;
+               rgmii-gmac0 = <1>;
+               rgmii-enabled = <1>;
+               rxd-delay = <1>;
+               txd-delay = <1>;
+       };
+};
+
+&wmac {
+       status = "okay";
+       qca,no-eeprom;
+};
+
+&pcie {
+       status = "okay";
+};
+
+&usb {
+       status = "okay";
+};
+
+&usb_phy {
+       status = "okay";
+};

diff --git a/target/linux/ath79/image/mikrotik.mk b/target/linux/ath79/image/mikrotik.mk
index 74f8603b5ab93ad1a438beebca7b31b48c799833..4256f773792b48bda2e4f51e7925b553c0bac9dc 100644 (file)
--- a/target/linux/ath79/image/mikrotik.mk
+++ b/target/linux/ath79/image/mikrotik.mk
@@ -9,6 +9,15 @@ define Device/mikrotik_routerboard-493g
 endef
 TARGET_DEVICES += mikrotik_routerboard-493g
 
+define Device/mikrotik_routerboard-912uag-2hpnd
+  $(Device/mikrotik_nand)
+  SOC := ar9342
+  DEVICE_MODEL := RouterBOARD 912UAG-2HPnD
+  DEVICE_PACKAGES += kmod-usb-ehci kmod-usb2
+  SUPPORTED_DEVICES += rb-912uag-2hpnd
+endef
+TARGET_DEVICES += mikrotik_routerboard-912uag-2hpnd
+
 define Device/mikrotik_routerboard-921gs-5hpacd-15s
   $(Device/mikrotik_nand)
   SOC := qca9558

diff --git a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
index 54e7bb20cf10eb57b76df750de4406ed34d7b030..bd249e0b86de5705f0c0634c50edf24dac673900 100755 (executable)
--- a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
@@ -15,6 +15,7 @@ ath79_setup_interfaces()
                ucidef_add_switch "switch1" \
                        "0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
                ;;
+       mikrotik,routerboard-912uag-2hpnd|\
        mikrotik,routerboard-921gs-5hpacd-15s|\
        mikrotik,routerboard-lhg-2nd|\
        mikrotik,routerboard-sxt-5nd-r2|\
@@ -37,6 +38,7 @@ ath79_setup_macs()
        local mac_base="$(cat /sys/firmware/mikrotik/hard_config/mac_base)"
 
        case "$board" in
+       mikrotik,routerboard-912uag-2hpnd|\
        mikrotik,routerboard-921gs-5hpacd-15s|\
        mikrotik,routerboard-lhg-2nd|\
        mikrotik,routerboard-sxt-5nd-r2|\

diff --git a/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 7ef6fdbe0fdb46f3e3f956ad8b39bf35a94fd536..ae0c94d8ec996527bb0b8658d6b14be9da42e9ea 100644 (file)
--- a/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -23,6 +23,7 @@ board=$(board_name)
 case "$FIRMWARE" in
 "ath9k-eeprom-ahb-18100000.wmac.bin")
        case $board in
+       mikrotik,routerboard-912uag-2hpnd|\
        mikrotik,routerboard-lhg-2nd|\
        mikrotik,routerboard-sxt-5nd-r2|\
        mikrotik,routerboard-wapr-2nd)

diff --git a/target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh b/target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh
index 97d388168f5dee08b56756666d9dcf47a548d697..6962c6fdcc508c621b718739406e5dfb00cc4182 100644 (file)
--- a/target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh
@@ -32,6 +32,7 @@ platform_do_upgrade() {
 
        case "$board" in
        mikrotik,routerboard-493g|\
+       mikrotik,routerboard-912uag-2hpnd|\
        mikrotik,routerboard-921gs-5hpacd-15s|\
        mikrotik,routerboard-922uags-5hpacd|\
        mikrotik,routerboard-sxt-5nd-r2)