--- /dev/null
+From 078ced30af696b52a450a016a16eb47499d68117 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij@linaro.org>
+Date: Wed, 8 Jul 2020 14:25:36 +0200
+Subject: [PATCH 2/5] net: dsa: tag_rtl4_a: Implement Realtek 4 byte A tag
+
+This implements the known parts of the Realtek 4 byte
+tag protocol version 0xA, as found in the RTL8366RB
+DSA switch.
+
+It is designated as protocol version 0xA as a
+different Realtek 4 byte tag format with protocol
+version 0x9 is known to exist in the Realtek RTL8306
+chips.
+
+The tag and switch chip lacks public documentation, so
+the tag format has been reverse-engineered from
+packet dumps. As only ingress traffic has been available
+for analysis an egress tag has not been possible to
+develop (even using educated guesses about bit fields)
+so this is as far as it gets. It is not known if the
+switch even supports egress tagging.
+
+Excessive attempts to figure out the egress tag format
+was made. When nothing else worked, I just tried all bit
+combinations with 0xannp where a is protocol and p is
+port. I looped through all values several times trying
+to get a response from ping, without any positive
+result.
+
+Using just these ingress tags however, the switch
+functionality is vastly improved and the packets find
+their way into the destination port without any
+tricky VLAN configuration. On the D-Link DIR-685 the
+LAN ports now come up and respond to ping without
+any command line configuration so this is a real
+improvement for users.
+
+Egress packets need to be restricted to the proper
+target ports using VLAN, which the RTL8366RB DSA
+switch driver already sets up.
+
+Cc: DENG Qingfang <dqfext@gmail.com>
+Cc: Mauri Sandberg <sandberg@mailfence.com>
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
+Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
+Signed-off-by: David S. Miller <davem@davemloft.net>
+---
+ include/net/dsa.h | 2 +
+ net/dsa/Kconfig | 7 +++
+ net/dsa/Makefile | 1 +
+ net/dsa/tag_rtl4_a.c | 130 +++++++++++++++++++++++++++++++++++++++++++
+ 4 files changed, 140 insertions(+)
+ create mode 100644 net/dsa/tag_rtl4_a.c
+
+--- a/include/net/dsa.h
++++ b/include/net/dsa.h
+@@ -42,6 +42,7 @@ struct phylink_link_state;
+ #define DSA_TAG_PROTO_8021Q_VALUE 12
+ #define DSA_TAG_PROTO_SJA1105_VALUE 13
+ #define DSA_TAG_PROTO_KSZ8795_VALUE 14
++#define DSA_TAG_PROTO_RTL4_A_VALUE 17
+
+ enum dsa_tag_protocol {
+ DSA_TAG_PROTO_NONE = DSA_TAG_PROTO_NONE_VALUE,
+@@ -59,6 +60,7 @@ enum dsa_tag_protocol {
+ DSA_TAG_PROTO_8021Q = DSA_TAG_PROTO_8021Q_VALUE,
+ DSA_TAG_PROTO_SJA1105 = DSA_TAG_PROTO_SJA1105_VALUE,
+ DSA_TAG_PROTO_KSZ8795 = DSA_TAG_PROTO_KSZ8795_VALUE,
++ DSA_TAG_PROTO_RTL4_A = DSA_TAG_PROTO_RTL4_A_VALUE,
+ };
+
+ struct packet_type;
+--- a/net/dsa/Kconfig
++++ b/net/dsa/Kconfig
+@@ -80,6 +80,13 @@ config NET_DSA_TAG_KSZ
+ Say Y if you want to enable support for tagging frames for the
+ Microchip 8795/9477/9893 families of switches.
+
++config NET_DSA_TAG_RTL4_A
++ tristate "Tag driver for Realtek 4 byte protocol A tags"
++ help
++ Say Y or M if you want to enable support for tagging frames for the
++ Realtek switches with 4 byte protocol A tags, sich as found in
++ the Realtek RTL8366RB.
++
+ config NET_DSA_TAG_QCA
+ tristate "Tag driver for Qualcomm Atheros QCA8K switches"
+ help
+--- a/net/dsa/Makefile
++++ b/net/dsa/Makefile
+@@ -10,6 +10,7 @@ obj-$(CONFIG_NET_DSA_TAG_DSA) += tag_dsa
+ obj-$(CONFIG_NET_DSA_TAG_EDSA) += tag_edsa.o
+ obj-$(CONFIG_NET_DSA_TAG_GSWIP) += tag_gswip.o
+ obj-$(CONFIG_NET_DSA_TAG_KSZ) += tag_ksz.o
++obj-$(CONFIG_NET_DSA_TAG_RTL4_A) += tag_rtl4_a.o
+ obj-$(CONFIG_NET_DSA_TAG_LAN9303) += tag_lan9303.o
+ obj-$(CONFIG_NET_DSA_TAG_MTK) += tag_mtk.o
+ obj-$(CONFIG_NET_DSA_TAG_QCA) += tag_qca.o
+--- /dev/null
++++ b/net/dsa/tag_rtl4_a.c
+@@ -0,0 +1,130 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Handler for Realtek 4 byte DSA switch tags
++ * Currently only supports protocol "A" found in RTL8366RB
++ * Copyright (c) 2020 Linus Walleij <linus.walleij@linaro.org>
++ *
++ * This "proprietary tag" header looks like so:
++ *
++ * -------------------------------------------------
++ * | MAC DA | MAC SA | 0x8899 | 2 bytes tag | Type |
++ * -------------------------------------------------
++ *
++ * The 2 bytes tag form a 16 bit big endian word. The exact
++ * meaning has been guessed from packet dumps from ingress
++ * frames, as no working egress traffic has been available
++ * we do not know the format of the egress tags or if they
++ * are even supported.
++ */
++
++#include <linux/etherdevice.h>
++#include <linux/bits.h>
++
++#include "dsa_priv.h"
++
++#define RTL4_A_HDR_LEN 4
++#define RTL4_A_ETHERTYPE 0x8899
++#define RTL4_A_PROTOCOL_SHIFT 12
++/*
++ * 0x1 = Realtek Remote Control protocol (RRCP)
++ * 0x2/0x3 seems to be used for loopback testing
++ * 0x9 = RTL8306 DSA protocol
++ * 0xa = RTL8366RB DSA protocol
++ */
++#define RTL4_A_PROTOCOL_RTL8366RB 0xa
++
++static struct sk_buff *rtl4a_tag_xmit(struct sk_buff *skb,
++ struct net_device *dev)
++{
++ /*
++ * Just let it pass thru, we don't know if it is possible
++ * to tag a frame with the 0x8899 ethertype and direct it
++ * to a specific port, all attempts at reverse-engineering have
++ * ended up with the frames getting dropped.
++ *
++ * The VLAN set-up needs to restrict the frames to the right port.
++ *
++ * If you have documentation on the tagging format for RTL8366RB
++ * (tag type A) then please contribute.
++ */
++ return skb;
++}
++
++static struct sk_buff *rtl4a_tag_rcv(struct sk_buff *skb,
++ struct net_device *dev,
++ struct packet_type *pt)
++{
++ u16 protport;
++ __be16 *p;
++ u16 etype;
++ u8 *tag;
++ u8 prot;
++ u8 port;
++
++ if (unlikely(!pskb_may_pull(skb, RTL4_A_HDR_LEN)))
++ return NULL;
++
++ /* The RTL4 header has its own custom Ethertype 0x8899 and that
++ * starts right at the beginning of the packet, after the src
++ * ethernet addr. Apparantly skb->data always points 2 bytes in,
++ * behind the Ethertype.
++ */
++ tag = skb->data - 2;
++ p = (__be16 *)tag;
++ etype = ntohs(*p);
++ if (etype != RTL4_A_ETHERTYPE) {
++ /* Not custom, just pass through */
++ netdev_dbg(dev, "non-realtek ethertype 0x%04x\n", etype);
++ return skb;
++ }
++ p = (__be16 *)(tag + 2);
++ protport = ntohs(*p);
++ /* The 4 upper bits are the protocol */
++ prot = (protport >> RTL4_A_PROTOCOL_SHIFT) & 0x0f;
++ if (prot != RTL4_A_PROTOCOL_RTL8366RB) {
++ netdev_err(dev, "unknown realtek protocol 0x%01x\n", prot);
++ return NULL;
++ }
++ port = protport & 0xff;
++
++ skb->dev = dsa_master_find_slave(dev, 0, port);
++ if (!skb->dev) {
++ netdev_dbg(dev, "could not find slave for port %d\n", port);
++ return NULL;
++ }
++
++ /* Remove RTL4 tag and recalculate checksum */
++ skb_pull_rcsum(skb, RTL4_A_HDR_LEN);
++
++ /* Move ethernet DA and SA in front of the data */
++ memmove(skb->data - ETH_HLEN,
++ skb->data - ETH_HLEN - RTL4_A_HDR_LEN,
++ 2 * ETH_ALEN);
++
++ skb->offload_fwd_mark = 1;
++
++ return skb;
++}
++
++static int rtl4a_tag_flow_dissect(const struct sk_buff *skb, __be16 *proto,
++ int *offset)
++{
++ *offset = RTL4_A_HDR_LEN;
++ /* Skip past the tag and fetch the encapsulated Ethertype */
++ *proto = ((__be16 *)skb->data)[1];
++
++ return 0;
++}
++
++static const struct dsa_device_ops rtl4a_netdev_ops = {
++ .name = "rtl4a",
++ .proto = DSA_TAG_PROTO_RTL4_A,
++ .xmit = rtl4a_tag_xmit,
++ .rcv = rtl4a_tag_rcv,
++ .flow_dissect = rtl4a_tag_flow_dissect,
++ .overhead = RTL4_A_HDR_LEN,
++};
++module_dsa_tag_driver(rtl4a_netdev_ops);
++
++MODULE_LICENSE("GPL");
++MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_RTL4_A);
--- /dev/null
+From c633ba43b7a9c2bfdb992ffd198d4c661520466f Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij@linaro.org>
+Date: Wed, 8 Jul 2020 14:25:37 +0200
+Subject: [PATCH 3/5] net: dsa: rtl8366rb: Support the CPU DSA tag
+
+This activates the support to use the CPU tag to properly
+direct ingress traffic to the right port.
+
+Bit 15 in register RTL8368RB_CPU_CTRL_REG can be set to
+1 to disable the insertion of the CPU tag which is what
+the code currently does. The bit 15 define calls this
+setting RTL8368RB_CPU_INSTAG which is confusing since the
+inverse meaning is implied: programmers may think that
+setting this bit to 1 will *enable* inserting the tag
+rather than disabling it, so rename this setting in
+bit 15 to RTL8368RB_CPU_NO_TAG which is more to the
+point.
+
+After this e.g. ping works out-of-the-box with the
+RTL8366RB.
+
+Cc: DENG Qingfang <dqfext@gmail.com>
+Cc: Mauri Sandberg <sandberg@mailfence.com>
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
+Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
+Signed-off-by: David S. Miller <davem@davemloft.net>
+---
+ drivers/net/dsa/Kconfig | 1 +
+ drivers/net/dsa/rtl8366rb.c | 31 ++++++++-----------------------
+ 2 files changed, 9 insertions(+), 23 deletions(-)
+
+--- a/drivers/net/dsa/Kconfig
++++ b/drivers/net/dsa/Kconfig
+@@ -66,6 +66,7 @@ config NET_DSA_QCA8K
+ config NET_DSA_REALTEK_SMI
+ tristate "Realtek SMI Ethernet switch family support"
+ depends on NET_DSA
++ select NET_DSA_TAG_RTL4_A
+ select FIXED_PHY
+ select IRQ_DOMAIN
+ select REALTEK_PHY
+--- a/drivers/net/dsa/rtl8366rb.c
++++ b/drivers/net/dsa/rtl8366rb.c
+@@ -109,8 +109,8 @@
+ /* CPU port control reg */
+ #define RTL8368RB_CPU_CTRL_REG 0x0061
+ #define RTL8368RB_CPU_PORTS_MSK 0x00FF
+-/* Enables inserting custom tag length/type 0x8899 */
+-#define RTL8368RB_CPU_INSTAG BIT(15)
++/* Disables inserting custom tag length/type 0x8899 */
++#define RTL8368RB_CPU_NO_TAG BIT(15)
+
+ #define RTL8366RB_SMAR0 0x0070 /* bits 0..15 */
+ #define RTL8366RB_SMAR1 0x0071 /* bits 16..31 */
+@@ -844,16 +844,14 @@ static int rtl8366rb_setup(struct dsa_sw
+ if (ret)
+ return ret;
+
+- /* Enable CPU port and enable inserting CPU tag
++ /* Enable CPU port with custom DSA tag 8899.
+ *
+- * Disabling RTL8368RB_CPU_INSTAG here will change the behaviour
+- * of the switch totally and it will start talking Realtek RRCP
+- * internally. It is probably possible to experiment with this,
+- * but then the kernel needs to understand and handle RRCP first.
++ * If you set RTL8368RB_CPU_NO_TAG (bit 15) in this registers
++ * the custom tag is turned off.
+ */
+ ret = regmap_update_bits(smi->map, RTL8368RB_CPU_CTRL_REG,
+ 0xFFFF,
+- RTL8368RB_CPU_INSTAG | BIT(smi->cpu_port));
++ BIT(smi->cpu_port));
+ if (ret)
+ return ret;
+
+@@ -966,21 +964,8 @@ static int rtl8366rb_setup(struct dsa_sw
+ static enum dsa_tag_protocol rtl8366_get_tag_protocol(struct dsa_switch *ds,
+ int port)
+ {
+- /* For now, the RTL switches are handled without any custom tags.
+- *
+- * It is possible to turn on "custom tags" by removing the
+- * RTL8368RB_CPU_INSTAG flag when enabling the port but what it
+- * does is unfamiliar to DSA: ethernet frames of type 8899, the Realtek
+- * Remote Control Protocol (RRCP) start to appear on the CPU port of
+- * the device. So this is not the ordinary few extra bytes in the
+- * frame. Instead it appears that the switch starts to talk Realtek
+- * RRCP internally which means a pretty complex RRCP implementation
+- * decoding and responding the RRCP protocol is needed to exploit this.
+- *
+- * The OpenRRCP project (dormant since 2009) have reverse-egineered
+- * parts of the protocol.
+- */
+- return DSA_TAG_PROTO_NONE;
++ /* This switch uses the 4 byte protocol A Realtek DSA tag */
++ return DSA_TAG_PROTO_RTL4_A;
+ }
+
+ static void rtl8366rb_adjust_link(struct dsa_switch *ds, int port,
projects / openwrt / staging / zorun.git / commitdiff