jadecpu ARM926EJS (MB86R01 SoC)
zmx25 ARM926EJS (imx25 SoC)
-Richard Woodruff <r-woodruff2@ti.com>
-
- omap2420h4 ARM1136EJS
-
Josh Wu <josh.wu@atmel.com>
at91sam9n12ek ARM926EJS (AT91SAM9N12 SoC)
orr r0,r0,#0xd3
msr cpsr,r0
-#ifdef CONFIG_OMAP2420H4
- /* Copy vectors to mask ROM indirect addr */
- adr r0, _start /* r0 <- current position of code */
- add r0, r0, #4 /* skip reset vector */
- mov r2, #64 /* r2 <- size to copy */
- add r2, r0, r2 /* r2 <- source end address */
- mov r1, #SRAM_OFFSET0 /* build vect addr */
- mov r3, #SRAM_OFFSET1
- add r1, r1, r3
- mov r3, #SRAM_OFFSET2
- add r1, r1, r3
-next:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- bne next /* loop until equal */
- bl cpy_clk_code /* put dpll adjust code behind vectors */
-#endif
/* the mask ROM code should have PLL and others stable */
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
bl cpu_init_crit
+++ /dev/null
-/* bits.h
- * Copyright (c) 2004 Texas Instruments
- *
- * This package is free software; you can redistribute it and/or
- * modify it under the terms of the license found in the file
- * named COPYING that should have accompanied this file.
- *
- * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
- * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
- */
-#ifndef __bits_h
-#define __bits_h 1
-
-#define BIT0 (1<<0)
-#define BIT1 (1<<1)
-#define BIT2 (1<<2)
-#define BIT3 (1<<3)
-#define BIT4 (1<<4)
-#define BIT5 (1<<5)
-#define BIT6 (1<<6)
-#define BIT7 (1<<7)
-#define BIT8 (1<<8)
-#define BIT9 (1<<9)
-#define BIT10 (1<<10)
-#define BIT11 (1<<11)
-#define BIT12 (1<<12)
-#define BIT13 (1<<13)
-#define BIT14 (1<<14)
-#define BIT15 (1<<15)
-#define BIT16 (1<<16)
-#define BIT17 (1<<17)
-#define BIT18 (1<<18)
-#define BIT19 (1<<19)
-#define BIT20 (1<<20)
-#define BIT21 (1<<21)
-#define BIT22 (1<<22)
-#define BIT23 (1<<23)
-#define BIT24 (1<<24)
-#define BIT25 (1<<25)
-#define BIT26 (1<<26)
-#define BIT27 (1<<27)
-#define BIT28 (1<<28)
-#define BIT29 (1<<29)
-#define BIT30 (1<<30)
-#define BIT31 (1<<31)
-
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#ifndef _OMAP24XX_CLOCKS_H_
-#define _OMAP24XX_CLOCKS_H_
-
-#define COMMIT_DIVIDERS 0x1
-
-#define MODE_BYPASS_FAST 0x2
-#define APLL_LOCK 0xc
-#ifdef CONFIG_APTIX
-#define DPLL_LOCK 0x1 /* stay in bypass mode */
-#else
-#define DPLL_LOCK 0x3 /* DPLL lock */
-#endif
-
-/****************************************************************************;
-; PRCM Scheme II
-;
-; Enable clocks and DPLL for:
-; DPLL=300, DPLLout=600 M=1,N=50 CM_CLKSEL1_PLL[21:8] 12/2*50
-; Core=600 (core domain) DPLLx2 CM_CLKSEL2_PLL[1:0]
-; MPUF=300 (mpu domain) 2 CM_CLKSEL_MPU[4:0]
-; DSPF=200 (dsp domain) 3 CM_CLKSEL_DSP[4:0]
-; DSPI=100 6 CM_CLKSEL_DSP[6:5]
-; DSP_S bypass CM_CLKSEL_DSP[7]
-; IVAF=200 (dsp domain) 3 CM_CLKSEL_DSP[12:8]
-; IVAF=100 auto
-; IVAI auto
-; IVA_MPU auto
-; IVA_S bypass CM_CLKSEL_DSP[13]
-; GFXF=50 (gfx domain) 12 CM_CLKSEL_FGX[2:0]
-; SSI_SSRF=200 3 CM_CLKSEL1_CORE[24:20]
-; SSI_SSTF=100 auto
-; L3=100Mhz (sdram) 6 CM_CLKSEL1_CORE[4:0]
-; L4=100Mhz 6
-; C_L4_USB=50 12 CM_CLKSEL1_CORE[6:5]
-***************************************************************************/
-#define II_DPLL_OUT_X2 0x2 /* x2 core out */
-#define II_MPU_DIV 0x2 /* mpu = core/2 */
-#define II_DSP_DIV 0x343 /* dsp & iva divider */
-#define II_GFX_DIV 0x2
-#define II_BUS_DIV 0x04601026
-#define II_DPLL_300 0x01832100
-
-/****************************************************************************;
-; PRCM Scheme III
-;
-; Enable clocks and DPLL for:
-; DPLL=266, DPLLout=532 M=5+1,N=133 CM_CLKSEL1_PLL[21:8] 12/6*133=266
-; Core=532 (core domain) DPLLx2 CM_CLKSEL2_PLL[1:0]
-; MPUF=266 (mpu domain) /2 CM_CLKSEL_MPU[4:0]
-; DSPF=177.3 (dsp domain) /3 CM_CLKSEL_DSP[4:0]
-; DSPI=88.67 /6 CM_CLKSEL_DSP[6:5]
-; DSP_S ACTIVATED CM_CLKSEL_DSP[7]
-; IVAF=88.67 (dsp domain) /3 CM_CLKSEL_DSP[12:8]
-; IVAF=88.67 auto
-; IVAI auto
-; IVA_MPU auto
-; IVA_S ACTIVATED CM_CLKSEL_DSP[13]
-; GFXF=66.5 (gfx domain) /8 CM_CLKSEL_FGX[2:0]:
-; SSI_SSRF=177.3 /3 CM_CLKSEL1_CORE[24:20]
-; SSI_SSTF=88.67 auto
-; L3=133Mhz (sdram) /4 CM_CLKSEL1_CORE[4:0]
-; L4=66.5Mhz /8
-; C_L4_USB=33.25 /16 CM_CLKSEL1_CORE[6:5]
-***************************************************************************/
-#define III_DPLL_OUT_X2 0x2 /* x2 core out */
-#define III_MPU_DIV 0x2 /* mpu = core/2 */
-#define III_DSP_DIV 0x23C3 /* dsp & iva divider sych enabled*/
-#define III_GFX_DIV 0x2
-#define III_BUS_DIV 0x08301044
-#define III_DPLL_266 0x01885500
-
-/* set defaults for boot up */
-#ifdef PRCM_CONFIG_II
-# define DPLL_OUT II_DPLL_OUT_X2
-# define MPU_DIV II_MPU_DIV
-# define DSP_DIV II_DSP_DIV
-# define GFX_DIV II_GFX_DIV
-# define BUS_DIV II_BUS_DIV
-# define DPLL_VAL II_DPLL_300
-#elif PRCM_CONFIG_III
-# define DPLL_OUT III_DPLL_OUT_X2
-# define MPU_DIV III_MPU_DIV
-# define DSP_DIV III_DSP_DIV
-# define GFX_DIV III_GFX_DIV
-# define BUS_DIV III_BUS_DIV
-# define DPLL_VAL III_DPLL_266
-#endif
-
-/* lock delay time out */
-#define LDELAY 12000000
-
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#ifndef _OMAP24XX_I2C_H_
-#define _OMAP24XX_I2C_H_
-
-#define I2C_BASE1 0x48070000
-#define I2C_BASE2 0x48072000 /* nothing hooked up on h4 */
-
-#define I2C_DEFAULT_BASE I2C_BASE1
-
-struct i2c {
- unsigned short rev; /* 0x00 */
- unsigned short res1;
- unsigned short ie; /* 0x04 */
- unsigned short res2;
- unsigned short stat; /* 0x08 */
- unsigned short res3;
- unsigned short iv; /* 0x0C */
- unsigned short res4;
- unsigned short syss; /* 0x10 */
- unsigned short res4p1;
- unsigned short buf; /* 0x14 */
- unsigned short res5;
- unsigned short cnt; /* 0x18 */
- unsigned short res6;
- unsigned short data; /* 0x1C */
- unsigned short res7;
- unsigned short sysc; /* 0x20 */
- unsigned short res8;
- unsigned short con; /* 0x24 */
- unsigned short res9;
- unsigned short oa; /* 0x28 */
- unsigned short res10;
- unsigned short sa; /* 0x2C */
- unsigned short res11;
- unsigned short psc; /* 0x30 */
- unsigned short res12;
- unsigned short scll; /* 0x34 */
- unsigned short res13;
- unsigned short sclh; /* 0x38 */
- unsigned short res14;
- unsigned short systest; /* 0x3c */
- unsigned short res15;
-};
-
-#define I2C_BUS_MAX 2
-
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef _OMAP24XX_MEM_H_
-#define _OMAP24XX_MEM_H_
-
-#define SDRC_CS0_OSET 0x0
-#define SDRC_CS1_OSET 0x30 /* mirror CS1 regs appear offset 0x30 from CS0 */
-
-#ifndef __ASSEMBLY__
-/* struct's for holding data tables for current boards, they are getting used
- early in init when NO global access are there */
-struct sdrc_data_s {
- u32 sdrc_sharing;
- u32 sdrc_mdcfg_0_ddr;
- u32 sdrc_mdcfg_0_sdr;
- u32 sdrc_actim_ctrla_0;
- u32 sdrc_actim_ctrlb_0;
- u32 sdrc_rfr_ctrl;
- u32 sdrc_mr_0_ddr;
- u32 sdrc_mr_0_sdr;
- u32 sdrc_dllab_ctrl;
-} /*__attribute__ ((packed))*/;
-typedef struct sdrc_data_s sdrc_data_t;
-
-typedef enum {
- STACKED = 0,
- IP_DDR = 1,
- COMBO_DDR = 2,
- IP_SDR = 3,
-} mem_t;
-
-#endif
-
-/* Slower full frequency range default timings for x32 operation*/
-#define H4_2420_SDRC_SHARING 0x00000100
-#define H4_2420_SDRC_MDCFG_0_SDR 0x00D04010 /* discrete sdr module */
-#define H4_2420_SDRC_MR_0_SDR 0x00000031
-#define H4_2420_SDRC_MDCFG_0_DDR 0x01702011 /* descrite ddr module */
-#define H4_2420_COMBO_MDCFG_0_DDR 0x00801011 /* combo module */
-#define H4_2420_SDRC_MR_0_DDR 0x00000032
-
-#define H4_2422_SDRC_SHARING 0x00004b00
-#define H4_2422_SDRC_MDCFG_0_DDR 0x00801011 /* stacked ddr on 2422 */
-#define H4_2422_SDRC_MR_0_DDR 0x00000032
-
-/* ES1 work around timings */
-#define H4_242x_SDRC_ACTIM_CTRLA_0_ES1 0x9bead909 /* 165Mhz for use with 100/133 */
-#define H4_242x_SDRC_ACTIM_CTRLB_0_ES1 0x00000020
-#define H4_242x_SDRC_RFR_CTRL_ES1 0x00002401 /* use over refresh for ES1 */
-
-/* optimized timings good for current shipping parts */
-#define H4_242X_SDRC_ACTIM_CTRLA_0_100MHz 0x5A59B485
-#define H4_242X_SDRC_ACTIM_CTRLB_0_100MHz 0x0000000e
-#define H4_242X_SDRC_ACTIM_CTRLA_0_133MHz 0x8BA6E6C8 /* temp warn 0 settings */
-#define H4_242X_SDRC_ACTIM_CTRLB_0_133MHz 0x00000010 /* temp warn 0 settings */
-#define H4_242X_SDRC_RFR_CTRL_100MHz 0x0002da01
-#define H4_242X_SDRC_RFR_CTRL_133MHz 0x0003de01
-#define H4_242x_SDRC_DLLAB_CTRL_100MHz 0x0000980E /* 72deg, allow DPLLout*1 to work (combo)*/
-#define H4_242x_SDRC_DLLAB_CTRL_133MHz 0x0000690E /* 72deg, for ES2 */
-
-#ifdef PRCM_CONFIG_II
-# define H4_2420_SDRC_ACTIM_CTRLA_0 H4_242X_SDRC_ACTIM_CTRLA_0_100MHz
-# define H4_2420_SDRC_ACTIM_CTRLB_0 H4_242X_SDRC_ACTIM_CTRLB_0_100MHz
-# define H4_2420_SDRC_RFR_CTRL H4_242X_SDRC_RFR_CTRL_100MHz
-# define H4_2420_SDRC_DLLAB_CTRL H4_242x_SDRC_DLLAB_CTRL_100MHz
-# define H4_2422_SDRC_ACTIM_CTRLA_0 H4_242X_SDRC_ACTIM_CTRLA_0_100MHz
-# define H4_2422_SDRC_ACTIM_CTRLB_0 H4_242X_SDRC_ACTIM_CTRLB_0_100MHz
-# define H4_2422_SDRC_RFR_CTRL H4_242X_SDRC_RFR_CTRL_100MHz
-# define H4_2422_SDRC_DLLAB_CTRL H4_242x_SDRC_DLLAB_CTRL_100MHz
-#elif PRCM_CONFIG_III
-# define H4_2420_SDRC_ACTIM_CTRLA_0 H4_242X_SDRC_ACTIM_CTRLA_0_133MHz
-# define H4_2420_SDRC_ACTIM_CTRLB_0 H4_242X_SDRC_ACTIM_CTRLB_0_133MHz
-# define H4_2420_SDRC_RFR_CTRL H4_242X_SDRC_RFR_CTRL_133MHz
-# define H4_2420_SDRC_DLLAB_CTRL H4_242x_SDRC_DLLAB_CTRL_133MHz
-# define H4_2422_SDRC_ACTIM_CTRLA_0 H4_242X_SDRC_ACTIM_CTRLA_0_100MHz
-# define H4_2422_SDRC_ACTIM_CTRLB_0 H4_242X_SDRC_ACTIM_CTRLB_0_100MHz
-# define H4_2422_SDRC_RFR_CTRL H4_242X_SDRC_RFR_CTRL_100MHz
-# define H4_2422_SDRC_DLLAB_CTRL H4_242x_SDRC_DLLAB_CTRL_100MHz
-#endif
-
-
-/* GPMC settings */
-#ifdef PRCM_CONFIG_II /* L3 at 100MHz */
-# ifdef CONFIG_SYS_NAND_BOOT
-# define H4_24XX_GPMC_CONFIG1_0 0x0
-# define H4_24XX_GPMC_CONFIG2_0 0x00141400
-# define H4_24XX_GPMC_CONFIG3_0 0x00141400
-# define H4_24XX_GPMC_CONFIG4_0 0x0F010F01
-# define H4_24XX_GPMC_CONFIG5_0 0x010C1414
-# define H4_24XX_GPMC_CONFIG6_0 0x00000A80
-# else /* else NOR */
-# define H4_24XX_GPMC_CONFIG1_0 0x3
-# define H4_24XX_GPMC_CONFIG2_0 0x000f0f01
-# define H4_24XX_GPMC_CONFIG3_0 0x00050502
-# define H4_24XX_GPMC_CONFIG4_0 0x0C060C06
-# define H4_24XX_GPMC_CONFIG5_0 0x01131F1F
-# endif /* endif CONFIG_SYS_NAND_BOOT */
-# define H4_24XX_GPMC_CONFIG7_0 (0x00000C40|(H4_CS0_BASE >> 24))
-# define H4_24XX_GPMC_CONFIG1_1 0x00011000
-# define H4_24XX_GPMC_CONFIG2_1 0x001F1F00
-# define H4_24XX_GPMC_CONFIG3_1 0x00080802
-# define H4_24XX_GPMC_CONFIG4_1 0x1C091C09
-# define H4_24XX_GPMC_CONFIG5_1 0x031A1F1F
-# define H4_24XX_GPMC_CONFIG6_1 0x000003C2
-# define H4_24XX_GPMC_CONFIG7_1 (0x00000F40|(H4_CS1_BASE >> 24))
-#endif /* endif PRCM_CONFIG_II */
-
-#ifdef PRCM_CONFIG_III /* L3 at 133MHz */
-# ifdef CONFIG_SYS_NAND_BOOT
-# define H4_24XX_GPMC_CONFIG1_0 0x0
-# define H4_24XX_GPMC_CONFIG2_0 0x00141400
-# define H4_24XX_GPMC_CONFIG3_0 0x00141400
-# define H4_24XX_GPMC_CONFIG4_0 0x0F010F01
-# define H4_24XX_GPMC_CONFIG5_0 0x010C1414
-# define H4_24XX_GPMC_CONFIG6_0 0x00000A80
-# else /* NOR boot */
-# define H4_24XX_GPMC_CONFIG1_0 0x3
-# define H4_24XX_GPMC_CONFIG2_0 0x00151501
-# define H4_24XX_GPMC_CONFIG3_0 0x00060602
-# define H4_24XX_GPMC_CONFIG4_0 0x10081008
-# define H4_24XX_GPMC_CONFIG5_0 0x01131F1F
-# define H4_24XX_GPMC_CONFIG6_0 0x000004c4
-# endif /* endif CONFIG_SYS_NAND_BOOT */
-# define H4_24XX_GPMC_CONFIG7_0 (0x00000C40|(H4_CS0_BASE >> 24))
-# define H4_24XX_GPMC_CONFIG1_1 0x00011000
-# define H4_24XX_GPMC_CONFIG2_1 0x001f1f01
-# define H4_24XX_GPMC_CONFIG3_1 0x00080803
-# define H4_24XX_GPMC_CONFIG4_1 0x1C091C09
-# define H4_24XX_GPMC_CONFIG5_1 0x041f1F1F
-# define H4_24XX_GPMC_CONFIG6_1 0x000004C4
-# define H4_24XX_GPMC_CONFIG7_1 (0x00000F40|(H4_CS1_BASE >> 24))
-#endif /* endif CONFIG_SYS_PRCM_III */
-
-#endif /* endif _OMAP24XX_MEM_H_ */
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#ifndef _OMAP2420_MUX_H_
-#define _OMAP2420_MUX_H_
-
-#ifndef __ASSEMBLY__
-typedef unsigned char uint8;
-typedef unsigned int uint32;
-
-void muxSetupSDRC(void);
-void muxSetupGPMC(void);
-void muxSetupUsb0(void);
-void muxSetupUsbHost(void);
-void muxSetupUart3(void);
-void muxSetupI2C1(void);
-void muxSetupUART1(void);
-void muxSetupLCD(void);
-void muxSetupCamera(void);
-void muxSetupMMCSD(void) ;
-void muxSetupTouchScreen(void) ;
-void muxSetupHDQ(void);
-#endif
-
-#define USB_OTG_CTRL ((volatile uint32 *)0x4805E30C)
-
-/* Pin Muxing registers used for HDQ (Smart battery) */
-#define CONTROL_PADCONF_HDQ_SIO ((volatile unsigned char *)0x48000115)
-
-/* Pin Muxing registers used for GPMC */
-#define CONTROL_PADCONF_GPMC_D2_BYTE0 ((volatile unsigned char *)0x48000088)
-#define CONTROL_PADCONF_GPMC_D2_BYTE1 ((volatile unsigned char *)0x48000089)
-#define CONTROL_PADCONF_GPMC_D2_BYTE2 ((volatile unsigned char *)0x4800008A)
-#define CONTROL_PADCONF_GPMC_D2_BYTE3 ((volatile unsigned char *)0x4800008B)
-
-#define CONTROL_PADCONF_GPMC_NCS0_BYTE0 ((volatile unsigned char *)0x4800008C)
-#define CONTROL_PADCONF_GPMC_NCS0_BYTE1 ((volatile unsigned char *)0x4800008D)
-#define CONTROL_PADCONF_GPMC_NCS0_BYTE2 ((volatile unsigned char *)0x4800008E)
-#define CONTROL_PADCONF_GPMC_NCS0_BYTE3 ((volatile unsigned char *)0x4800008F)
-#define CONTROL_PADCONF_GPMC_NCS0_BYTE4 (0x48000090)
-#define CONTROL_PADCONF_GPMC_NCS0_BYTE5 (0x48000091)
-#define CONTROL_PADCONF_GPMC_NCS0_BYTE6 (0x48000092)
-#define CONTROL_PADCONF_GPMC_NCS0_BYTE7 (0x48000093)
-
-/* Pin Muxing registers used for SDRC */
-#define CONTROL_PADCONF_SDRC_NCS0_BYTE0 ((volatile unsigned char *)0x480000A0)
-#define CONTROL_PADCONF_SDRC_NCS0_BYTE1 ((volatile unsigned char *)0x480000A1)
-#define CONTROL_PADCONF_SDRC_NCS0_BYTE2 ((volatile unsigned char *)0x480000A2)
-#define CONTROL_PADCONF_SDRC_NCS0_BYTE3 ((volatile unsigned char *)0x480000A3)
-
-#define CONTROL_PADCONF_SDRC_A14_BYTE0 ((volatile unsigned char *)0x48000030)
-#define CONTROL_PADCONF_SDRC_A14_BYTE1 ((volatile unsigned char *)0x48000031)
-#define CONTROL_PADCONF_SDRC_A14_BYTE2 ((volatile unsigned char *)0x48000032)
-#define CONTROL_PADCONF_SDRC_A14_BYTE3 ((volatile unsigned char *)0x48000033)
-
-/* Pin Muxing registers used for Touch Screen (SPI) */
-#define CONTROL_PADCONF_SPI1_CLK ((volatile unsigned char *)0x480000FF)
-#define CONTROL_PADCONF_SPI1_SIMO ((volatile unsigned char *)0x48000100)
-#define CONTROL_PADCONF_SPI1_SOMI ((volatile unsigned char *)0x48000101)
-#define CONTROL_PADCONF_SPI1_NCS0 ((volatile unsigned char *)0x48000102)
-#define CONTROL_PADCONF_SPI1_NCS1 (0x48000103)
-
-#define CONTROL_PADCONF_MCBSP1_FSR ((volatile unsigned char *)0x4800010B)
-
-/* Pin Muxing registers used for MMCSD */
-#define CONTROL_PADCONF_MMC_CLKI ((volatile unsigned char *)0x480000FE)
-#define CONTROL_PADCONF_MMC_CLKO ((volatile unsigned char *)0x480000F3)
-#define CONTROL_PADCONF_MMC_CMD ((volatile unsigned char *)0x480000F4)
-#define CONTROL_PADCONF_MMC_DAT0 ((volatile unsigned char *)0x480000F5)
-#define CONTROL_PADCONF_MMC_DAT1 ((volatile unsigned char *)0x480000F6)
-#define CONTROL_PADCONF_MMC_DAT2 ((volatile unsigned char *)0x480000F7)
-#define CONTROL_PADCONF_MMC_DAT3 ((volatile unsigned char *)0x480000F8)
-#define CONTROL_PADCONF_MMC_DAT_DIR0 ((volatile unsigned char *)0x480000F9)
-#define CONTROL_PADCONF_MMC_DAT_DIR1 ((volatile unsigned char *)0x480000FA)
-#define CONTROL_PADCONF_MMC_DAT_DIR2 ((volatile unsigned char *)0x480000FB)
-#define CONTROL_PADCONF_MMC_DAT_DIR3 ((volatile unsigned char *)0x480000FC)
-#define CONTROL_PADCONF_MMC_CMD_DIR ((volatile unsigned char *)0x480000FD)
-
-#define CONTROL_PADCONF_SDRC_A14 ((volatile unsigned char *)0x48000030)
-#define CONTROL_PADCONF_SDRC_A13 ((volatile unsigned char *)0x48000031)
-
-/* Pin Muxing registers used for CAMERA */
-#define CONTROL_PADCONF_SYS_NRESWARM ((volatile unsigned char *)0x4800012B)
-
-#define CONTROL_PADCONF_CAM_XCLK ((volatile unsigned char *)0x480000DC)
-#define CONTROL_PADCONF_CAM_LCLK ((volatile unsigned char *)0x480000DB)
-#define CONTROL_PADCONF_CAM_VS ((volatile unsigned char *)0x480000DA)
-#define CONTROL_PADCONF_CAM_HS ((volatile unsigned char *)0x480000D9)
-#define CONTROL_PADCONF_CAM_D0 ((volatile unsigned char *)0x480000D8)
-#define CONTROL_PADCONF_CAM_D1 ((volatile unsigned char *)0x480000D7)
-#define CONTROL_PADCONF_CAM_D2 ((volatile unsigned char *)0x480000D6)
-#define CONTROL_PADCONF_CAM_D3 ((volatile unsigned char *)0x480000D5)
-#define CONTROL_PADCONF_CAM_D4 ((volatile unsigned char *)0x480000D4)
-#define CONTROL_PADCONF_CAM_D5 ((volatile unsigned char *)0x480000D3)
-#define CONTROL_PADCONF_CAM_D6 ((volatile unsigned char *)0x480000D2)
-#define CONTROL_PADCONF_CAM_D7 ((volatile unsigned char *)0x480000D1)
-#define CONTROL_PADCONF_CAM_D8 ((volatile unsigned char *)0x480000D0)
-#define CONTROL_PADCONF_CAM_D9 ((volatile unsigned char *)0x480000CF)
-
-/* Pin Muxing registers used for LCD */
-#define CONTROL_PADCONF_DSS_D0 ((volatile unsigned char *)0x480000B3)
-#define CONTROL_PADCONF_DSS_D1 ((volatile unsigned char *)0x480000B4)
-#define CONTROL_PADCONF_DSS_D2 ((volatile unsigned char *)0x480000B5)
-#define CONTROL_PADCONF_DSS_D3 ((volatile unsigned char *)0x480000B6)
-#define CONTROL_PADCONF_DSS_D4 ((volatile unsigned char *)0x480000B7)
-#define CONTROL_PADCONF_DSS_D5 ((volatile unsigned char *)0x480000B8)
-#define CONTROL_PADCONF_DSS_D6 ((volatile unsigned char *)0x480000B9)
-#define CONTROL_PADCONF_DSS_D7 ((volatile unsigned char *)0x480000BA)
-#define CONTROL_PADCONF_DSS_D8 ((volatile unsigned char *)0x480000BB)
-#define CONTROL_PADCONF_DSS_D9 ((volatile unsigned char *)0x480000BC)
-#define CONTROL_PADCONF_DSS_D10 ((volatile unsigned char *)0x480000BD)
-#define CONTROL_PADCONF_DSS_D11 ((volatile unsigned char *)0x480000BE)
-#define CONTROL_PADCONF_DSS_D12 ((volatile unsigned char *)0x480000BF)
-#define CONTROL_PADCONF_DSS_D13 ((volatile unsigned char *)0x480000C0)
-#define CONTROL_PADCONF_DSS_D14 ((volatile unsigned char *)0x480000C1)
-#define CONTROL_PADCONF_DSS_D15 ((volatile unsigned char *)0x480000C2)
-#define CONTROL_PADCONF_DSS_D16 ((volatile unsigned char *)0x480000C3)
-#define CONTROL_PADCONF_DSS_D17 ((volatile unsigned char *)0x480000C4)
-#define CONTROL_PADCONF_DSS_PCLK ((volatile unsigned char *)0x480000CB)
-#define CONTROL_PADCONF_DSS_VSYNC ((volatile unsigned char *)0x480000CC)
-#define CONTROL_PADCONF_DSS_HSYNC ((volatile unsigned char *)0x480000CD)
-#define CONTROL_PADCONF_DSS_ACBIAS ((volatile unsigned char *)0x480000CE)
-
-/* Pin Muxing registers used for UART1 */
-#define CONTROL_PADCONF_UART1_CTS ((volatile unsigned char *)0x480000C5)
-#define CONTROL_PADCONF_UART1_RTS ((volatile unsigned char *)0x480000C6)
-#define CONTROL_PADCONF_UART1_TX ((volatile unsigned char *)0x480000C7)
-#define CONTROL_PADCONF_UART1_RX ((volatile unsigned char *)0x480000C8)
-
-/* Pin Muxing registers used for I2C1 */
-#define CONTROL_PADCONF_I2C1_SCL ((volatile unsigned char *)0x48000111)
-#define CONTROL_PADCONF_I2C1_SDA ((volatile unsigned char *)0x48000112)
-
-/* Pin Muxing registres used for USB0. */
-#define CONTROL_PADCONF_USB0_PUEN ((volatile uint8 *)0x4800011D)
-#define CONTROL_PADCONF_USB0_VP ((volatile uint8 *)0x4800011E)
-#define CONTROL_PADCONF_USB0_VM ((volatile uint8 *)0x4800011F)
-#define CONTROL_PADCONF_USB0_RCV ((volatile uint8 *)0x48000120)
-#define CONTROL_PADCONF_USB0_TXEN ((volatile uint8 *)0x48000121)
-#define CONTROL_PADCONF_USB0_SE0 ((volatile uint8 *)0x48000122)
-#define CONTROL_PADCONF_USB0_DAT ((volatile uint8 *)0x48000123)
-
-/* Pin Muxing registres used for USB1. */
-#define CONTROL_PADCONF_USB1_RCV (0x480000EB)
-#define CONTROL_PADCONF_USB1_TXEN (0x480000EC)
-
-/* Pin Muxing registers used for UART3/IRDA */
-#define CONTROL_PADCONF_UART3_TX_IRTX ((volatile uint8 *)0x48000118)
-#define CONTROL_PADCONF_UART3_RX_IRRX ((volatile uint8 *)0x48000119)
-
-/* Pin Muxing registers used for GPIO */
-#define CONTROL_PADCONF_GPIO69 (0x480000ED)
-#define CONTROL_PADCONF_GPIO70 (0x480000EE)
-#define CONTROL_PADCONF_GPIO102 (0x48000116)
-#define CONTROL_PADCONF_GPIO103 (0x48000117)
-#define CONTROL_PADCONF_GPIO104 (0x48000118)
-#define CONTROL_PADCONF_GPIO105 (0x48000119)
-
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef _OMAP2420_SYS_H_
-#define _OMAP2420_SYS_H_
-
-#include <asm/sizes.h>
-
-/*
- * 2420 specific Section
- */
-
-/* L3 Firewall */
-#define A_REQINFOPERM0 0x68005048
-#define A_READPERM0 0x68005050
-#define A_WRITEPERM0 0x68005058
-/* #define GP_DEVICE (BIT8|BIT9) FIXME -- commented out to make compile -- FIXME */
-
-/* L3 Firewall */
-#define A_REQINFOPERM0 0x68005048
-#define A_READPERM0 0x68005050
-#define A_WRITEPERM0 0x68005058
-
-/* CONTROL */
-#define OMAP2420_CTRL_BASE (0x48000000)
-#define CONTROL_STATUS (OMAP2420_CTRL_BASE + 0x2F8)
-
-/* device type */
-#define TST_DEVICE 0x0
-#define EMU_DEVICE 0x1
-#define HS_DEVICE 0x2
-#define GP_DEVICE 0x3
-
-/* TAP information */
-#define OMAP2420_TAP_BASE (0x48014000)
-#define TAP_IDCODE_REG (OMAP2420_TAP_BASE+0x204)
-#define PRODUCTION_ID (OMAP2420_TAP_BASE+0x208)
-
-/* GPMC */
-#define OMAP2420_GPMC_BASE (0x6800A000)
-#define GPMC_SYSCONFIG (OMAP2420_GPMC_BASE+0x10)
-#define GPMC_IRQENABLE (OMAP2420_GPMC_BASE+0x1C)
-#define GPMC_TIMEOUT_CONTROL (OMAP2420_GPMC_BASE+0x40)
-#define GPMC_CONFIG (OMAP2420_GPMC_BASE+0x50)
-#define GPMC_CONFIG1_0 (OMAP2420_GPMC_BASE+0x60)
-#define GPMC_CONFIG2_0 (OMAP2420_GPMC_BASE+0x64)
-#define GPMC_CONFIG3_0 (OMAP2420_GPMC_BASE+0x68)
-#define GPMC_CONFIG4_0 (OMAP2420_GPMC_BASE+0x6C)
-#define GPMC_CONFIG5_0 (OMAP2420_GPMC_BASE+0x70)
-#define GPMC_CONFIG6_0 (OMAP2420_GPMC_BASE+0x74)
-#define GPMC_CONFIG7_0 (OMAP2420_GPMC_BASE+0x78)
-#define GPMC_CONFIG1_1 (OMAP2420_GPMC_BASE+0x90)
-#define GPMC_CONFIG2_1 (OMAP2420_GPMC_BASE+0x94)
-#define GPMC_CONFIG3_1 (OMAP2420_GPMC_BASE+0x98)
-#define GPMC_CONFIG4_1 (OMAP2420_GPMC_BASE+0x9C)
-#define GPMC_CONFIG5_1 (OMAP2420_GPMC_BASE+0xA0)
-#define GPMC_CONFIG6_1 (OMAP2420_GPMC_BASE+0xA4)
-#define GPMC_CONFIG7_1 (OMAP2420_GPMC_BASE+0xA8)
-#define GPMC_CONFIG1_2 (OMAP2420_GPMC_BASE+0xC0)
-#define GPMC_CONFIG2_2 (OMAP2420_GPMC_BASE+0xC4)
-#define GPMC_CONFIG3_2 (OMAP2420_GPMC_BASE+0xC8)
-#define GPMC_CONFIG4_2 (OMAP2420_GPMC_BASE+0xCC)
-#define GPMC_CONFIG5_2 (OMAP2420_GPMC_BASE+0xD0)
-#define GPMC_CONFIG6_2 (OMAP2420_GPMC_BASE+0xD4)
-#define GPMC_CONFIG7_2 (OMAP2420_GPMC_BASE+0xD8)
-#define GPMC_CONFIG1_3 (OMAP2420_GPMC_BASE+0xF0)
-#define GPMC_CONFIG2_3 (OMAP2420_GPMC_BASE+0xF4)
-#define GPMC_CONFIG3_3 (OMAP2420_GPMC_BASE+0xF8)
-#define GPMC_CONFIG4_3 (OMAP2420_GPMC_BASE+0xFC)
-#define GPMC_CONFIG5_3 (OMAP2420_GPMC_BASE+0x100)
-#define GPMC_CONFIG6_3 (OMAP2420_GPMC_BASE+0x104)
-#define GPMC_CONFIG7_3 (OMAP2420_GPMC_BASE+0x108)
-
-/* SMS */
-#define OMAP2420_SMS_BASE 0x68008000
-#define SMS_SYSCONFIG (OMAP2420_SMS_BASE+0x10)
-#define SMS_CLASS_ARB0 (OMAP2420_SMS_BASE+0xD0)
-# define BURSTCOMPLETE_GROUP7 BIT31
-
-/* SDRC */
-#define OMAP2420_SDRC_BASE 0x68009000
-#define SDRC_SYSCONFIG (OMAP2420_SDRC_BASE+0x10)
-#define SDRC_STATUS (OMAP2420_SDRC_BASE+0x14)
-#define SDRC_CS_CFG (OMAP2420_SDRC_BASE+0x40)
-#define SDRC_SHARING (OMAP2420_SDRC_BASE+0x44)
-#define SDRC_DLLA_CTRL (OMAP2420_SDRC_BASE+0x60)
-#define SDRC_DLLB_CTRL (OMAP2420_SDRC_BASE+0x68)
-#define SDRC_POWER (OMAP2420_SDRC_BASE+0x70)
-#define SDRC_MCFG_0 (OMAP2420_SDRC_BASE+0x80)
-#define SDRC_MR_0 (OMAP2420_SDRC_BASE+0x84)
-#define SDRC_ACTIM_CTRLA_0 (OMAP2420_SDRC_BASE+0x9C)
-#define SDRC_ACTIM_CTRLB_0 (OMAP2420_SDRC_BASE+0xA0)
-#define SDRC_ACTIM_CTRLA_1 (OMAP2420_SDRC_BASE+0xC4)
-#define SDRC_ACTIM_CTRLB_1 (OMAP2420_SDRC_BASE+0xC8)
-#define SDRC_RFR_CTRL (OMAP2420_SDRC_BASE+0xA4)
-#define SDRC_MANUAL_0 (OMAP2420_SDRC_BASE+0xA8)
-#define OMAP2420_SDRC_CS0 0x80000000
-#define OMAP2420_SDRC_CS1 0xA0000000
-#define CMD_NOP 0x0
-#define CMD_PRECHARGE 0x1
-#define CMD_AUTOREFRESH 0x2
-#define CMD_ENTR_PWRDOWN 0x3
-#define CMD_EXIT_PWRDOWN 0x4
-#define CMD_ENTR_SRFRSH 0x5
-#define CMD_CKE_HIGH 0x6
-#define CMD_CKE_LOW 0x7
-#define SOFTRESET BIT1
-#define SMART_IDLE (0x2 << 3)
-#define REF_ON_IDLE (0x1 << 6)
-
-
-/* UART */
-#define OMAP2420_UART1 0x4806A000
-#define OMAP2420_UART2 0x4806C000
-#define OMAP2420_UART3 0x4806E000
-
-/* General Purpose Timers */
-#define OMAP2420_GPT1 0x48028000
-#define OMAP2420_GPT2 0x4802A000
-#define OMAP2420_GPT3 0x48078000
-#define OMAP2420_GPT4 0x4807A000
-#define OMAP2420_GPT5 0x4807C000
-#define OMAP2420_GPT6 0x4807E000
-#define OMAP2420_GPT7 0x48080000
-#define OMAP2420_GPT8 0x48082000
-#define OMAP2420_GPT9 0x48084000
-#define OMAP2420_GPT10 0x48086000
-#define OMAP2420_GPT11 0x48088000
-#define OMAP2420_GPT12 0x4808A000
-
-/* timer regs offsets (32 bit regs) */
-#define TIDR 0x0 /* r */
-#define TIOCP_CFG 0x10 /* rw */
-#define TISTAT 0x14 /* r */
-#define TISR 0x18 /* rw */
-#define TIER 0x1C /* rw */
-#define TWER 0x20 /* rw */
-#define TCLR 0x24 /* rw */
-#define TCRR 0x28 /* rw */
-#define TLDR 0x2C /* rw */
-#define TTGR 0x30 /* rw */
-#define TWPS 0x34 /* r */
-#define TMAR 0x38 /* rw */
-#define TCAR1 0x3c /* r */
-#define TSICR 0x40 /* rw */
-#define TCAR2 0x44 /* r */
-
-/* WatchDog Timers (1 secure, 3 GP) */
-#define WD1_BASE 0x48020000
-#define WD2_BASE 0x48022000
-#define WD3_BASE 0x48024000
-#define WD4_BASE 0x48026000
-#define WWPS 0x34 /* r */
-#define WSPR 0x48 /* rw */
-#define WD_UNLOCK1 0xAAAA
-#define WD_UNLOCK2 0x5555
-
-/* PRCM */
-#define OMAP2420_CM_BASE 0x48008000
-#define PRCM_CLKCFG_CTRL (OMAP2420_CM_BASE+0x080)
-#define CM_CLKSEL_MPU (OMAP2420_CM_BASE+0x140)
-#define CM_FCLKEN1_CORE (OMAP2420_CM_BASE+0x200)
-#define CM_FCLKEN2_CORE (OMAP2420_CM_BASE+0x204)
-#define CM_ICLKEN1_CORE (OMAP2420_CM_BASE+0x210)
-#define CM_ICLKEN2_CORE (OMAP2420_CM_BASE+0x214)
-#define CM_CLKSEL1_CORE (OMAP2420_CM_BASE+0x240)
-#define CM_CLKSEL_WKUP (OMAP2420_CM_BASE+0x440)
-#define CM_CLKSEL2_CORE (OMAP2420_CM_BASE+0x244)
-#define CM_CLKSEL_GFX (OMAP2420_CM_BASE+0x340)
-#define PM_RSTCTRL_WKUP (OMAP2420_CM_BASE+0x450)
-#define CM_CLKEN_PLL (OMAP2420_CM_BASE+0x500)
-#define CM_IDLEST_CKGEN (OMAP2420_CM_BASE+0x520)
-#define CM_CLKSEL1_PLL (OMAP2420_CM_BASE+0x540)
-#define CM_CLKSEL2_PLL (OMAP2420_CM_BASE+0x544)
-#define CM_CLKSEL_DSP (OMAP2420_CM_BASE+0x840)
-
-/*
- * H4 specific Section
- */
-
-/*
- * The 2420's chip selects are programmable. The mask ROM
- * does configure CS0 to 0x08000000 before dispatch. So, if
- * you want your code to live below that address, you have to
- * be prepared to jump though hoops, to reset the base address.
- */
-#if defined(CONFIG_OMAP2420H4)
-/* GPMC */
-#ifdef CONFIG_VIRTIO_A /* Pre version B */
-# define H4_CS0_BASE 0x08000000 /* flash (64 Meg aligned) */
-# define H4_CS1_BASE 0x04000000 /* debug board */
-# define H4_CS2_BASE 0x0A000000 /* wifi board */
-#else
-# define H4_CS0_BASE 0x08000000 /* flash (64 Meg aligned) */
-# define H4_CS1_BASE 0x04000000 /* debug board */
-# define H4_CS2_BASE 0x0C000000 /* wifi board */
-#endif
-
-/* base address for indirect vectors (internal boot mode) */
-#define SRAM_OFFSET0 0x40000000
-#define SRAM_OFFSET1 0x00200000
-#define SRAM_OFFSET2 0x0000F800
-#define SRAM_VECT_CODE (SRAM_OFFSET0|SRAM_OFFSET1|SRAM_OFFSET2)
-
-/* FPGA on Debug board.*/
-#define ETH_CONTROL_REG (H4_CS1_BASE+0x30b)
-#define LAN_RESET_REGISTER (H4_CS1_BASE+0x1c)
-#endif /* endif CONFIG_2420H4 */
-
-/* Common */
-#define LOW_LEVEL_SRAM_STACK 0x4020FFFC
-
-#define PERIFERAL_PORT_BASE 0x480FE003
-
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef _OMAP24XX_SYS_INFO_H_
-#define _OMAP24XX_SYS_INFO_H_
-
-typedef struct h4_system_data {
- /* base board info */
- u32 base_b_rev; /* rev from base board i2c */
- /* cpu board info */
- u32 cpu_b_rev; /* rev from cpu board i2c */
- u32 cpu_b_mux; /* mux type on daughter board */
- u32 cpu_b_ddr_type; /* mem type */
- u32 cpu_b_ddr_speed; /* ddr speed rating */
- u32 cpu_b_switches; /* boot ctrl switch settings */
- /* cpu info */
- u32 cpu_type; /* type of cpu; 2420, 2422, 2430,...*/
- u32 cpu_rev; /* rev of given cpu; ES1, ES2,...*/
-} h4_sys_data;
-
-#define XDR_POP 5 /* package on package part */
-#define SDR_DISCRETE 4 /* 128M memory SDR module*/
-#define DDR_STACKED 3 /* stacked part on 2422 */
-#define DDR_COMBO 2 /* combo part on cpu daughter card (menalaeus) */
-#define DDR_DISCRETE 1 /* 2x16 parts on daughter card */
-
-#define DDR_100 100 /* type found on most mem d-boards */
-#define DDR_111 111 /* some combo parts */
-#define DDR_133 133 /* most combo, some mem d-boards */
-#define DDR_165 165 /* future parts */
-
-#define CPU_2420 0x2420
-#define CPU_2422 0x2422 /* 2420 + 64M stacked */
-#define CPU_2423 0x2423 /* 2420 + 96M stacked */
-
-#define CPU_2422_ES1 1
-#define CPU_2422_ES2 2
-#define CPU_2420_ES1 1
-#define CPU_2420_ES2 2
-#define CPU_2420_2422_ES1 1
-
-#define CPU_2420_CHIPID 0x0B5D9000
-#define CPU_24XX_ID_MASK 0x0FFFF000
-#define CPU_242X_REV_MASK 0xF0000000
-#define CPU_242X_PID_MASK 0x000F0000
-
-#define BOARD_H4_MENELAUS 1
-#define BOARD_H4_SDP 2
-
-#define GPMC_MUXED 1
-#define GPMC_NONMUXED 0
-
-#define TYPE_NAND 0x800 /* bit pos for nand in gpmc reg */
-#define TYPE_NOR 0x000
-
-#define WIDTH_8BIT 0x0000
-#define WIDTH_16BIT 0x1000 /* bit pos for 16 bit in gpmc */
-
-#define I2C_MENELAUS 0x72 /* i2c id for companion chip */
-
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#ifndef _OMAP24XX_SYS_PROTO_H_
-#define _OMAP24XX_SYS_PROTO_H_
-
-void prcm_init(void);
-void memif_init(void);
-void sdrc_init(void);
-void do_sdrc_init(u32,u32);
-void gpmc_init(void);
-
-void ether_init(void);
-void watchdog_init(void);
-void set_muxconf_regs(void);
-void peripheral_enable(void);
-
-u32 get_cpu_type(void);
-u32 get_cpu_rev(void);
-u32 get_mem_type(void);
-u32 get_sysboot_value(void);
-u32 get_gpmc0_base(void);
-u32 is_gpmc_muxed(void);
-u32 get_gpmc0_type(void);
-u32 get_gpmc0_width(void);
-u32 wait_on_value(u32 read_bit_mask, u32 match_value, u32 read_addr, u32 bound);
-u32 get_board_type(void);
-void display_board_info(u32);
-void update_mux(u32,u32);
-u32 get_sdr_cs_size(u32 offset);
-
-u32 running_in_sdram(void);
-u32 running_in_sram(void);
-u32 running_in_flash(void);
-u32 running_from_internal_boot(void);
-u32 get_device_type(void);
-#endif
void __flush_cache(unsigned long start, unsigned long size)
{
-#if defined(CONFIG_OMAP2420) || defined(CONFIG_ARM1136)
+#if defined(CONFIG_ARM1136)
void arm1136_cache_flush(void);
arm1136_cache_flush();
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).o
-
-COBJS := omap2420h4.o mem.o sys_info.o
-SOBJS := lowlevel_init.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(call cmd_link_o_target, $(OBJS) $(SOBJS))
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-#
-# (C) Copyright 2004
-# Texas Instruments, <www.ti.com>
-#
-# TI H4 board with OMAP2420 (ARM1136) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# H4 has 1 bank of 32MB or 64MB mDDR-SDRAM on CS0
-# H4 has 1 bank of 32MB or 00MB mDDR-SDRAM on CS1
-# Physical Address:
-# 8000'0000 (bank0)
-# A000/0000 (bank1) ES2 will be configurable
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-
-# For use with external or internal boots.
-#CONFIG_SYS_TEXT_BASE = 0x80e80000
-
-# Used with full SRAM boot.
-# This is either with a GP system or a signed boot image.
-# easiest, and safest way to go if you can.
-#CONFIG_SYS_TEXT_BASE = 0x40270000
-
-
-# Handy to get symbols to debug ROM version.
-#CONFIG_SYS_TEXT_BASE = 0x0
-CONFIG_SYS_TEXT_BASE = 0x08000000
-#CONFIG_SYS_TEXT_BASE = 0x04000000
+++ /dev/null
-/*
- * Board specific setup info
- *
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/omap2420.h>
-#include <asm/arch/mem.h>
-#include <asm/arch/clock.h>
-
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE /* sdram load addr from config.mk */
-
-/**************************************************************************
- * cpy_clk_code: relocates clock code into SRAM where its safer to execute
- * R1 = SRAM destination address.
- *************************************************************************/
-.global cpy_clk_code
- cpy_clk_code:
- /* Copy DPLL code into SRAM */
- adr r0, go_to_speed /* get addr of clock setting code */
- mov r2, #384 /* r2 size to copy (div by 32 bytes) */
- mov r1, r1 /* r1 <- dest address (passed in) */
- add r2, r2, r0 /* r2 <- source end address */
-next2:
- ldmia r0!, {r3-r10} /* copy from source address [r0] */
- stmia r1!, {r3-r10} /* copy to target address [r1] */
- cmp r0, r2 /* until source end address [r2] */
- bne next2
- mov pc, lr /* back to caller */
-
-/* ****************************************************************************
- * go_to_speed: -Moves to bypass, -Commits clock dividers, -puts dpll at speed
- * -executed from SRAM.
- * R0 = PRCM_CLKCFG_CTRL - addr of valid reg
- * R1 = CM_CLKEN_PLL - addr dpll ctlr reg
- * R2 = dpll value
- * R3 = CM_IDLEST_CKGEN - addr dpll lock wait
- ******************************************************************************/
-.global go_to_speed
- go_to_speed:
- sub sp, sp, #0x4 /* get some stack space */
- str r4, [sp] /* save r4's value */
-
- /* move into fast relock bypass */
- ldr r8, pll_ctl_add
- mov r4, #0x2
- str r4, [r8]
- ldr r4, pll_stat
-block:
- ldr r8, [r4] /* wait for bypass to take effect */
- and r8, r8, #0x3
- cmp r8, #0x1
- bne block
-
- /* set new dpll dividers _after_ in bypass */
- ldr r4, pll_div_add
- ldr r8, pll_div_val
- str r8, [r4]
-
- /* now prepare GPMC (flash) for new dpll speed */
- /* flash needs to be stable when we jump back to it */
- ldr r4, cfg3_0_addr
- ldr r8, cfg3_0_val
- str r8, [r4]
- ldr r4, cfg4_0_addr
- ldr r8, cfg4_0_val
- str r8, [r4]
- ldr r4, cfg1_0_addr
- ldr r8, [r4]
- orr r8, r8, #0x3 /* up gpmc divider */
- str r8, [r4]
-
- /* setup to 2x loop though code. The first loop pre-loads the
- * icache, the 2nd commits the prcm config, and locks the dpll
- */
- mov r4, #0x1000 /* spin spin spin */
- mov r8, #0x4 /* first pass condition & set registers */
- cmp r8, #0x4
-2:
- ldrne r8, [r3] /* DPLL lock check */
- and r8, r8, #0x7
- cmp r8, #0x2
- beq 4f
-3:
- subeq r8, r8, #0x1
- streq r8, [r0] /* commit dividers (2nd time) */
- nop
-lloop1:
- sub r4, r4, #0x1 /* Loop currently necessary else bad jumps */
- nop
- cmp r4, #0x0
- bne lloop1
- mov r4, #0x40000
- cmp r8, #0x1
- nop
- streq r2, [r1] /* lock dpll (2nd time) */
- nop
-lloop2:
- sub r4, r4, #0x1 /* loop currently necessary else bad jumps */
- nop
- cmp r4, #0x0
- bne lloop2
- mov r4, #0x40000
- cmp r8, #0x1
- nop
- ldreq r8, [r3] /* get lock condition for dpll */
- cmp r8, #0x4 /* first time though? */
- bne 2b
- moveq r8, #0x2 /* set to dpll check condition. */
- beq 3b /* if condition not true branch */
-4:
- ldr r4, [sp]
- add sp, sp, #0x4 /* return stack space */
- mov pc, lr /* back to caller, locked */
-
-_go_to_speed: .word go_to_speed
-
-/* these constants need to be close for PIC code */
-cfg3_0_addr:
- .word GPMC_CONFIG3_0
-cfg3_0_val:
- .word H4_24XX_GPMC_CONFIG3_0
-cfg4_0_addr:
- .word GPMC_CONFIG4_0
-cfg4_0_val:
- .word H4_24XX_GPMC_CONFIG4_0
-cfg1_0_addr:
- .word GPMC_CONFIG1_0
-pll_ctl_add:
- .word CM_CLKEN_PLL
-pll_stat:
- .word CM_IDLEST_CKGEN
-pll_div_add:
- .word CM_CLKSEL1_PLL
-pll_div_val:
- .word DPLL_VAL /* DPLL setting (300MHz default) */
-
-.globl lowlevel_init
-lowlevel_init:
- ldr sp, SRAM_STACK
- str ip, [sp] /* stash old link register */
- mov ip, lr /* save link reg across call */
- bl s_init /* go setup pll,mux,memory */
- ldr ip, [sp] /* restore save ip */
- mov lr, ip /* restore link reg */
-
- /* map interrupt controller */
- ldr r0, VAL_INTH_SETUP
- mcr p15, 0, r0, c15, c2, 4
-
- /* back to arch calling code */
- mov pc, lr
-
- /* the literal pools origin */
- .ltorg
-
-REG_CONTROL_STATUS:
- .word CONTROL_STATUS
-VAL_INTH_SETUP:
- .word PERIFERAL_PORT_BASE
-SRAM_STACK:
- .word LOW_LEVEL_SRAM_STACK
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/arch/omap2420.h>
-#include <asm/io.h>
-#include <asm/arch/bits.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/mem.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/sys_info.h>
-
-/************************************************************
- * sdelay() - simple spin loop. Will be constant time as
- * its generally used in 12MHz bypass conditions only. This
- * is necessary until timers are accessible.
- *
- * not inline to increase chances its in cache when called
- *************************************************************/
-void sdelay (unsigned long loops)
-{
- __asm__ volatile ("1:\n" "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*********************************************************************************
- * prcm_init() - inits clocks for PRCM as defined in clocks.h (config II default).
- * -- called from SRAM, or Flash (using temp SRAM stack).
- *********************************************************************************/
-void prcm_init(void)
-{
- u32 div;
- void (*f_lock_pll) (u32, u32, u32, u32);
- extern void *_end_vect, *_start;
-
- f_lock_pll = (void *)((u32)&_end_vect - (u32)&_start + SRAM_VECT_CODE);
-
- __raw_writel(0, CM_FCLKEN1_CORE); /* stop all clocks to reduce ringing */
- __raw_writel(0, CM_FCLKEN2_CORE); /* may not be necessary */
- __raw_writel(0, CM_ICLKEN1_CORE);
- __raw_writel(0, CM_ICLKEN2_CORE);
-
- __raw_writel(DPLL_OUT, CM_CLKSEL2_PLL); /* set DPLL out */
- __raw_writel(MPU_DIV, CM_CLKSEL_MPU); /* set MPU divider */
- __raw_writel(DSP_DIV, CM_CLKSEL_DSP); /* set dsp and iva dividers */
- __raw_writel(GFX_DIV, CM_CLKSEL_GFX); /* set gfx dividers */
-
- div = BUS_DIV;
- __raw_writel(div, CM_CLKSEL1_CORE);/* set L3/L4/USB/Display/Vlnc/SSi dividers */
- sdelay(1000);
-
- if(running_in_sram()){
- /* If running fully from SRAM this is OK. The Flash bus drops out for just a little.
- * but then comes back. If running from Flash this sequence kills you, thus you need
- * to run it using CONFIG_PARTIAL_SRAM.
- */
- __raw_writel(MODE_BYPASS_FAST, CM_CLKEN_PLL); /* go to bypass, fast relock */
- wait_on_value(BIT0|BIT1, BIT0, CM_IDLEST_CKGEN, LDELAY); /* wait till in bypass */
- sdelay(1000);
- /* set clock selection and dpll dividers. */
- __raw_writel(DPLL_VAL, CM_CLKSEL1_PLL); /* set pll for target rate */
- __raw_writel(COMMIT_DIVIDERS, PRCM_CLKCFG_CTRL); /* commit dividers */
- sdelay(10000);
- __raw_writel(DPLL_LOCK, CM_CLKEN_PLL); /* enable dpll */
- sdelay(10000);
- wait_on_value(BIT0|BIT1, BIT1, CM_IDLEST_CKGEN, LDELAY); /*wait for dpll lock */
- }else if(running_in_flash()){
- /* if running from flash, need to jump to small relocated code area in SRAM.
- * This is the only safe spot to do configurations from.
- */
- (*f_lock_pll)(PRCM_CLKCFG_CTRL, CM_CLKEN_PLL, DPLL_LOCK, CM_IDLEST_CKGEN);
- }
-
- __raw_writel(DPLL_LOCK|APLL_LOCK, CM_CLKEN_PLL); /* enable apll */
- wait_on_value(BIT8, BIT8, CM_IDLEST_CKGEN, LDELAY); /* wait for apll lock */
- sdelay(1000);
-}
-
-/**************************************************************************
- * make_cs1_contiguous() - for es2 and above remap cs1 behind cs0 to allow
- * command line mem=xyz use all memory with out discontigious support
- * compiled in. Could do it at the ATAG, but there really is two banks...
- * Called as part of 2nd phase DDR init.
- **************************************************************************/
-void make_cs1_contiguous(void)
-{
- u32 size, a_add_low, a_add_high;
-
- size = get_sdr_cs_size(SDRC_CS0_OSET);
- size /= SZ_32M; /* find size to offset CS1 */
- a_add_high = (size & 3) << 8; /* set up low field */
- a_add_low = (size & 0x3C) >> 2; /* set up high field */
- __raw_writel((a_add_high|a_add_low),SDRC_CS_CFG);
-
-}
-
-/********************************************************
- * mem_ok() - test used to see if timings are correct
- * for a part. Helps in gussing which part
- * we are currently using.
- *******************************************************/
-u32 mem_ok(void)
-{
- u32 val1, val2;
- u32 pattern = 0x12345678;
-
- __raw_writel(0x0,OMAP2420_SDRC_CS0+0x400); /* clear pos A */
- __raw_writel(pattern, OMAP2420_SDRC_CS0); /* pattern to pos B */
- __raw_writel(0x0,OMAP2420_SDRC_CS0+4); /* remove pattern off the bus */
- val1 = __raw_readl(OMAP2420_SDRC_CS0+0x400); /* get pos A value */
- val2 = __raw_readl(OMAP2420_SDRC_CS0); /* get val2 */
-
- if ((val1 != 0) || (val2 != pattern)) /* see if pos A value changed*/
- return(0);
- else
- return(1);
-}
-
-
-/********************************************************
- * sdrc_init() - init the sdrc chip selects CS0 and CS1
- * - early init routines, called from flash or
- * SRAM.
- *******************************************************/
-void sdrc_init(void)
-{
- #define EARLY_INIT 1
- do_sdrc_init(SDRC_CS0_OSET, EARLY_INIT); /* only init up first bank here */
-}
-
-/*************************************************************************
- * do_sdrc_init(): initialize the SDRAM for use.
- * -called from low level code with stack only.
- * -code sets up SDRAM timing and muxing for 2422 or 2420.
- * -optimal settings can be placed here, or redone after i2c
- * inspection of board info
- *
- * This is a bit ugly, but should handle all memory moduels
- * used with the H4. The first time though this code from s_init()
- * we configure the first chip select. Later on we come back and
- * will configure the 2nd chip select if it exists.
- *
- **************************************************************************/
-void do_sdrc_init(u32 offset, u32 early)
-{
- u32 cpu, dllen=0, rev, common=0, cs0=0, pmask=0, pass_type, mtype;
- sdrc_data_t *sdata; /* do not change type */
- u32 a, b, r;
-
- static const sdrc_data_t sdrc_2422 =
- {
- H4_2422_SDRC_SHARING, H4_2422_SDRC_MDCFG_0_DDR, 0 , H4_2422_SDRC_ACTIM_CTRLA_0,
- H4_2422_SDRC_ACTIM_CTRLB_0, H4_2422_SDRC_RFR_CTRL, H4_2422_SDRC_MR_0_DDR,
- 0, H4_2422_SDRC_DLLAB_CTRL
- };
- static const sdrc_data_t sdrc_2420 =
- {
- H4_2420_SDRC_SHARING, H4_2420_SDRC_MDCFG_0_DDR, H4_2420_SDRC_MDCFG_0_SDR,
- H4_2420_SDRC_ACTIM_CTRLA_0, H4_2420_SDRC_ACTIM_CTRLB_0,
- H4_2420_SDRC_RFR_CTRL, H4_2420_SDRC_MR_0_DDR, H4_2420_SDRC_MR_0_SDR,
- H4_2420_SDRC_DLLAB_CTRL
- };
-
- if (offset == SDRC_CS0_OSET)
- cs0 = common = 1; /* int regs shared between both chip select */
-
- cpu = get_cpu_type();
- rev = get_cpu_rev();
-
- /* warning generated, though code generation is correct. this may bite later,
- * but is ok for now. there is only so much C code you can do on stack only
- * operation.
- */
- if (cpu == CPU_2422){
- sdata = (sdrc_data_t *)&sdrc_2422;
- pass_type = STACKED;
- } else{
- sdata = (sdrc_data_t *)&sdrc_2420;
- pass_type = IP_DDR;
- }
-
- __asm__ __volatile__("": : :"memory"); /* limit compiler scope */
-
- if (!early && (((mtype = get_mem_type()) == DDR_COMBO)||(mtype == DDR_STACKED))) {
- if(mtype == DDR_COMBO){
- pmask = BIT2;/* combo part has a shared CKE signal, can't use feature */
- pass_type = COMBO_DDR; /* CS1 config */
- __raw_writel((__raw_readl(SDRC_POWER)) & ~pmask, SDRC_POWER);
- }
- if(rev != CPU_2420_2422_ES1) /* for es2 and above smooth things out */
- make_cs1_contiguous();
- }
-
-next_mem_type:
- if (common) { /* do a SDRC reset between types to clear regs*/
- __raw_writel(SOFTRESET, SDRC_SYSCONFIG); /* reset sdrc */
- wait_on_value(BIT0, BIT0, SDRC_STATUS, 12000000);/* wait till reset done set */
- __raw_writel(0, SDRC_SYSCONFIG); /* clear soft reset */
- __raw_writel(sdata->sdrc_sharing, SDRC_SHARING);
-#ifdef POWER_SAVE
- __raw_writel(__raw_readl(SMS_SYSCONFIG)|SMART_IDLE, SMS_SYSCONFIG);
- __raw_writel(sdata->sdrc_sharing|SMART_IDLE, SDRC_SHARING);
- __raw_writel((__raw_readl(SDRC_POWER)|BIT6), SDRC_POWER);
-#endif
- }
-
- if ((pass_type == IP_DDR) || (pass_type == STACKED)) /* (IP ddr-CS0),(2422-CS0/CS1) */
- __raw_writel(sdata->sdrc_mdcfg_0_ddr, SDRC_MCFG_0+offset);
- else if (pass_type == COMBO_DDR){ /* (combo-CS0/CS1) */
- __raw_writel(H4_2420_COMBO_MDCFG_0_DDR,SDRC_MCFG_0+offset);
- } else if (pass_type == IP_SDR){ /* ip sdr-CS0 */
- __raw_writel(sdata->sdrc_mdcfg_0_sdr, SDRC_MCFG_0+offset);
- }
-
- a = sdata->sdrc_actim_ctrla_0;
- b = sdata->sdrc_actim_ctrlb_0;
- r = sdata->sdrc_dllab_ctrl;
-
- /* work around ES1 DDR issues */
- if((pass_type != IP_SDR) && (rev == CPU_2420_2422_ES1)){
- a = H4_242x_SDRC_ACTIM_CTRLA_0_ES1;
- b = H4_242x_SDRC_ACTIM_CTRLB_0_ES1;
- r = H4_242x_SDRC_RFR_CTRL_ES1;
- }
-
- if (cs0) {
- __raw_writel(a, SDRC_ACTIM_CTRLA_0);
- __raw_writel(b, SDRC_ACTIM_CTRLB_0);
- } else {
- __raw_writel(a, SDRC_ACTIM_CTRLA_1);
- __raw_writel(b, SDRC_ACTIM_CTRLB_1);
- }
- __raw_writel(r, SDRC_RFR_CTRL+offset);
-
- /* init sequence for mDDR/mSDR using manual commands (DDR is a bit different) */
- __raw_writel(CMD_NOP, SDRC_MANUAL_0+offset);
- sdelay(5000); /* susposed to be 100us per design spec for mddr/msdr */
- __raw_writel(CMD_PRECHARGE, SDRC_MANUAL_0+offset);
- __raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0+offset);
- __raw_writel(CMD_AUTOREFRESH, SDRC_MANUAL_0+offset);
-
- /*
- * CSx SDRC Mode Register
- * Burst length = (4 - DDR) (2-SDR)
- * Serial mode
- * CAS latency = x
- */
- if(pass_type == IP_SDR)
- __raw_writel(sdata->sdrc_mr_0_sdr, SDRC_MR_0+offset);
- else
- __raw_writel(sdata->sdrc_mr_0_ddr, SDRC_MR_0+offset);
-
- /* NOTE: ES1 242x _BUG_ DLL + External Bandwidth fix*/
- if (rev == CPU_2420_2422_ES1){
- dllen = (BIT0|BIT3); /* es1 clear both bit0 and bit3 */
- __raw_writel((__raw_readl(SMS_CLASS_ARB0)|BURSTCOMPLETE_GROUP7)
- ,SMS_CLASS_ARB0);/* enable bust complete for lcd */
- }
- else
- dllen = BIT0|BIT1; /* es2, clear bit0, and 1 (set phase to 72) */
-
- /* enable & load up DLL with good value for 75MHz, and set phase to 90
- * ES1 recommends 90 phase, ES2 recommends 72 phase.
- */
- if (common && (pass_type != IP_SDR)) {
- __raw_writel(sdata->sdrc_dllab_ctrl, SDRC_DLLA_CTRL);
- __raw_writel(sdata->sdrc_dllab_ctrl & ~(BIT2|dllen), SDRC_DLLA_CTRL);
- __raw_writel(sdata->sdrc_dllab_ctrl, SDRC_DLLB_CTRL);
- __raw_writel(sdata->sdrc_dllab_ctrl & ~(BIT2|dllen) , SDRC_DLLB_CTRL);
- }
- sdelay(90000);
-
- if(mem_ok())
- return; /* STACKED, other configued type */
- ++pass_type; /* IPDDR->COMBODDR->IPSDR for CS0 */
- goto next_mem_type;
-}
-
-/*****************************************************
- * gpmc_init(): init gpmc bus
- * Init GPMC for x16, MuxMode (SDRAM in x32).
- * This code can only be executed from SRAM or SDRAM.
- *****************************************************/
-void gpmc_init(void)
-{
- u32 mux=0, mtype, mwidth, rev, tval;
-
- rev = get_cpu_rev();
- if (rev == CPU_2420_2422_ES1)
- tval = 1;
- else
- tval = 0; /* disable bit switched meaning */
-
- /* global settings */
- __raw_writel(0x10, GPMC_SYSCONFIG); /* smart idle */
- __raw_writel(0x0, GPMC_IRQENABLE); /* isr's sources masked */
- __raw_writel(tval, GPMC_TIMEOUT_CONTROL);/* timeout disable */
-#ifdef CONFIG_SYS_NAND_BOOT
- __raw_writel(0x001, GPMC_CONFIG); /* set nWP, disable limited addr */
-#else
- __raw_writel(0x111, GPMC_CONFIG); /* set nWP, disable limited addr */
-#endif
-
- /* discover bus connection from sysboot */
- if (is_gpmc_muxed() == GPMC_MUXED)
- mux = BIT9;
- mtype = get_gpmc0_type();
- mwidth = get_gpmc0_width();
-
- /* setup cs0 */
- __raw_writel(0x0, GPMC_CONFIG7_0); /* disable current map */
- sdelay(1000);
-
-#ifdef CONFIG_SYS_NAND_BOOT
- __raw_writel(H4_24XX_GPMC_CONFIG1_0|mtype|mwidth, GPMC_CONFIG1_0);
-#else
- __raw_writel(H4_24XX_GPMC_CONFIG1_0|mux|mtype|mwidth, GPMC_CONFIG1_0);
-#endif
-
-#ifdef PRCM_CONFIG_III
- __raw_writel(H4_24XX_GPMC_CONFIG2_0, GPMC_CONFIG2_0);
-#endif
- __raw_writel(H4_24XX_GPMC_CONFIG3_0, GPMC_CONFIG3_0);
- __raw_writel(H4_24XX_GPMC_CONFIG4_0, GPMC_CONFIG4_0);
-#ifdef PRCM_CONFIG_III
- __raw_writel(H4_24XX_GPMC_CONFIG5_0, GPMC_CONFIG5_0);
- __raw_writel(H4_24XX_GPMC_CONFIG6_0, GPMC_CONFIG6_0);
-#endif
- __raw_writel(H4_24XX_GPMC_CONFIG7_0, GPMC_CONFIG7_0);/* enable new mapping */
- sdelay(2000);
-
- /* setup cs1 */
- __raw_writel(0, GPMC_CONFIG7_1); /* disable any mapping */
- sdelay(1000);
- __raw_writel(H4_24XX_GPMC_CONFIG1_1|mux, GPMC_CONFIG1_1);
- __raw_writel(H4_24XX_GPMC_CONFIG2_1, GPMC_CONFIG2_1);
- __raw_writel(H4_24XX_GPMC_CONFIG3_1, GPMC_CONFIG3_1);
- __raw_writel(H4_24XX_GPMC_CONFIG4_1, GPMC_CONFIG4_1);
- __raw_writel(H4_24XX_GPMC_CONFIG5_1, GPMC_CONFIG5_1);
- __raw_writel(H4_24XX_GPMC_CONFIG6_1, GPMC_CONFIG6_1);
- __raw_writel(H4_24XX_GPMC_CONFIG7_1, GPMC_CONFIG7_1); /* enable mapping */
- sdelay(2000);
-}
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <common.h>
-#include <netdev.h>
-#include <asm/arch/omap2420.h>
-#include <asm/io.h>
-#include <asm/arch/bits.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/sys_info.h>
-#include <asm/arch/mem.h>
-#include <i2c.h>
-#include <asm/mach-types.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void wait_for_command_complete(unsigned int wd_base);
-
-/*******************************************************
- * Routine: delay
- * Description: spinning delay to use before udelay works
- ******************************************************/
-static inline void delay (unsigned long loops)
-{
- __asm__ volatile ("1:\n" "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*****************************************
- * Routine: board_init
- * Description: Early hardware init.
- *****************************************/
-int board_init (void)
-{
- gpmc_init(); /* in SRAM or SDRM, finish GPMC */
-
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_H4; /* board id for linux */
- gd->bd->bi_boot_params = (OMAP2420_SDRC_CS0+0x100); /* adress of boot parameters */
-
- return 0;
-}
-
-/**********************************************************
- * Routine: try_unlock_sram()
- * Description: If chip is GP type, unlock the SRAM for
- * general use.
- ***********************************************************/
-void try_unlock_sram(void)
-{
- /* if GP device unlock device SRAM for general use */
- if (get_device_type() == GP_DEVICE) {
- __raw_writel(0xFF, A_REQINFOPERM0);
- __raw_writel(0xCFDE, A_READPERM0);
- __raw_writel(0xCFDE, A_WRITEPERM0);
- }
-}
-
-/**********************************************************
- * Routine: s_init
- * Description: Does early system init of muxing and clocks.
- * - Called path is with sram stack.
- **********************************************************/
-void s_init(void)
-{
- int in_sdram = running_in_sdram();
-
- watchdog_init();
- set_muxconf_regs();
- delay(100);
- try_unlock_sram();
-
- if(!in_sdram)
- prcm_init();
-
- peripheral_enable();
- icache_enable();
- if (!in_sdram)
- sdrc_init();
-}
-
-/*******************************************************
- * Routine: misc_init_r
- * Description: Init ethernet (done here so udelay works)
- ********************************************************/
-int misc_init_r (void)
-{
- ether_init(); /* better done here so timers are init'ed */
- return(0);
-}
-
-/****************************************
- * Routine: watchdog_init
- * Description: Shut down watch dogs
- *****************************************/
-void watchdog_init(void)
-{
- /* There are 4 watch dogs. 1 secure, and 3 general purpose.
- * The ROM takes care of the secure one. Of the 3 GP ones,
- * 1 can reset us directly, the other 2 only generate MPU interrupts.
- */
- __raw_writel(WD_UNLOCK1 ,WD2_BASE+WSPR);
- wait_for_command_complete(WD2_BASE);
- __raw_writel(WD_UNLOCK2 ,WD2_BASE+WSPR);
-
-#if MPU_WD_CLOCKED /* value 0x10 stick on aptix, BIT4 polarity seems oppsite*/
- __raw_writel(WD_UNLOCK1 ,WD3_BASE+WSPR);
- wait_for_command_complete(WD3_BASE);
- __raw_writel(WD_UNLOCK2 ,WD3_BASE+WSPR);
-
- __raw_writel(WD_UNLOCK1 ,WD4_BASE+WSPR);
- wait_for_command_complete(WD4_BASE);
- __raw_writel(WD_UNLOCK2 ,WD4_BASE+WSPR);
-#endif
-}
-
-/******************************************************
- * Routine: wait_for_command_complete
- * Description: Wait for posting to finish on watchdog
- ******************************************************/
-void wait_for_command_complete(unsigned int wd_base)
-{
- int pending = 1;
- do {
- pending = __raw_readl(wd_base+WWPS);
- } while (pending);
-}
-
-/*******************************************************************
- * Routine:ether_init
- * Description: take the Ethernet controller out of reset and wait
- * for the EEPROM load to complete.
- ******************************************************************/
-void ether_init (void)
-{
-#ifdef CONFIG_LAN91C96
- int cnt = 20;
-
- __raw_writeb(0x3,OMAP2420_CTRL_BASE+0x10a); /*protect->gpio95 */
-
- __raw_writew(0x0, LAN_RESET_REGISTER);
- do {
- __raw_writew(0x1, LAN_RESET_REGISTER);
- udelay (100);
- if (cnt == 0)
- goto h4reset_err_out;
- --cnt;
- } while (__raw_readw(LAN_RESET_REGISTER) != 0x1);
-
- cnt = 20;
-
- do {
- __raw_writew(0x0, LAN_RESET_REGISTER);
- udelay (100);
- if (cnt == 0)
- goto h4reset_err_out;
- --cnt;
- } while (__raw_readw(LAN_RESET_REGISTER) != 0x0000);
- udelay (1000);
-
- *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
- udelay (1000);
-
- h4reset_err_out:
- return;
-#endif
-}
-
-/**********************************************
- * Routine: dram_init
- * Description: sets uboots idea of sdram size
- **********************************************/
-int dram_init(void)
-{
- unsigned int size0=0,size1=0;
- u32 mtype, btype;
- u8 chg_on = 0x5; /* enable charge of back up battery */
- u8 vmode_on = 0x8C;
- #define NOT_EARLY 0
-
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); /* need this a bit early */
-
- btype = get_board_type();
- mtype = get_mem_type();
-
- display_board_info(btype);
- if (btype == BOARD_H4_MENELAUS){
- update_mux(btype,mtype); /* combo part on menelaus */
- i2c_write(I2C_MENELAUS, 0x20, 1, &chg_on, 1); /*fix POR reset bug */
- i2c_write(I2C_MENELAUS, 0x2, 1, &vmode_on, 1); /* VCORE change on VMODE */
- }
-
- if ((mtype == DDR_COMBO) || (mtype == DDR_STACKED)) {
- do_sdrc_init(SDRC_CS1_OSET, NOT_EARLY); /* init other chip select */
- }
- size0 = get_sdr_cs_size(SDRC_CS0_OSET);
- size1 = get_sdr_cs_size(SDRC_CS1_OSET);
-
- gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, size0 + size1);
-
- return 0;
-}
-
-void dram_init_banksize(void)
-{
- unsigned int size0, size1;
- u32 rev;
-
- rev = get_cpu_rev();
- size0 = get_sdr_cs_size(SDRC_CS0_OSET);
- size1 = get_sdr_cs_size(SDRC_CS1_OSET);
-
- if(rev == CPU_2420_2422_ES1) /* ES1's 128MB remap granularity isn't worth doing */
- gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
- else /* ES2 and above can remap at 32MB granularity */
- gd->bd->bi_dram[1].start = PHYS_SDRAM_1+size0;
- gd->bd->bi_dram[1].size = size1;
-
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = size0;
-}
-
-/**********************************************************
- * Routine: set_muxconf_regs
- * Description: Setting up the configuration Mux registers
- * specific to the hardware
- *********************************************************/
-void set_muxconf_regs (void)
-{
- muxSetupSDRC();
- muxSetupGPMC();
- muxSetupUsb0();
- muxSetupUart3();
- muxSetupI2C1();
- muxSetupUART1();
- muxSetupLCD();
- muxSetupCamera();
- muxSetupMMCSD();
- muxSetupTouchScreen();
- muxSetupHDQ();
-}
-
-/*****************************************************************
- * Routine: peripheral_enable
- * Description: Enable the clks & power for perifs (GPT2, UART1,...)
- ******************************************************************/
-void peripheral_enable(void)
-{
- unsigned int v, if_clks=0, func_clks=0;
-
- /* Enable GP2 timer.*/
- if_clks |= BIT4;
- func_clks |= BIT4;
- v = __raw_readl(CM_CLKSEL2_CORE) | 0x4; /* Sys_clk input OMAP2420_GPT2 */
- __raw_writel(v, CM_CLKSEL2_CORE);
- __raw_writel(0x1, CM_CLKSEL_WKUP);
-
-#ifdef CONFIG_SYS_NS16550
- /* Enable UART1 clock */
- func_clks |= BIT21;
- if_clks |= BIT21;
-#endif
- v = __raw_readl(CM_ICLKEN1_CORE) | if_clks; /* Interface clocks on */
- __raw_writel(v,CM_ICLKEN1_CORE );
- v = __raw_readl(CM_FCLKEN1_CORE) | func_clks; /* Functional Clocks on */
- __raw_writel(v, CM_FCLKEN1_CORE);
- delay(1000);
-
-#ifndef KERNEL_UPDATED
- {
-#define V1 0xffffffff
-#define V2 0x00000007
-
- __raw_writel(V1, CM_FCLKEN1_CORE);
- __raw_writel(V2, CM_FCLKEN2_CORE);
- __raw_writel(V1, CM_ICLKEN1_CORE);
- __raw_writel(V1, CM_ICLKEN2_CORE);
- }
-#endif
-}
-
-/****************************************
- * Routine: muxSetupUsb0 (ostboot)
- * Description: Setup usb muxing
- *****************************************/
-void muxSetupUsb0(void)
-{
- volatile uint8 *MuxConfigReg;
- volatile uint32 *otgCtrlReg;
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_PUEN;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VP;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VM;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_RCV;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_TXEN;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_SE0;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_DAT;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- /* setup for USB VBus detection */
- otgCtrlReg = (volatile uint32 *)USB_OTG_CTRL;
- *otgCtrlReg |= 0x00040000; /* bit 18 */
-}
-
-/****************************************
- * Routine: muxSetupUart3 (ostboot)
- * Description: Setup uart3 muxing
- *****************************************/
-void muxSetupUart3(void)
-{
- volatile uint8 *MuxConfigReg;
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_UART3_TX_IRTX;
- *MuxConfigReg &= (uint8)(~0x1F);
-
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_UART3_RX_IRRX;
- *MuxConfigReg &= (uint8)(~0x1F);
-}
-
-/****************************************
- * Routine: muxSetupI2C1 (ostboot)
- * Description: Setup i2c muxing
- *****************************************/
-void muxSetupI2C1(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* I2C1 Clock pin configuration, PIN = M19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_I2C1_SCL;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* I2C1 Data pin configuration, PIN = L15 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_I2C1_SDA;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* Pull-up required on data line */
- /* external pull-up already present. */
- /* *MuxConfigReg |= 0x18 ;*/ /* Mode = 0, PullTypeSel=PU, PullUDEnable=Enabled */
-}
-
-/****************************************
- * Routine: muxSetupUART1 (ostboot)
- * Description: Set up uart1 muxing
- *****************************************/
-void muxSetupUART1(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* UART1_CTS pin configuration, PIN = D21 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_CTS;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* UART1_RTS pin configuration, PIN = H21 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RTS;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* UART1_TX pin configuration, PIN = L20 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_TX;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* UART1_RX pin configuration, PIN = T21 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RX;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-}
-
-/****************************************
- * Routine: muxSetupLCD (ostboot)
- * Description: Setup lcd muxing
- *****************************************/
-void muxSetupLCD(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* LCD_D0 pin configuration, PIN = Y7 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D0;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D1 pin configuration, PIN = P10 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D1;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D2 pin configuration, PIN = V8 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D2;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D3 pin configuration, PIN = Y8 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D3;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D4 pin configuration, PIN = W8 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D4;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D5 pin configuration, PIN = R10 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D5;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D6 pin configuration, PIN = Y9 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D6;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D7 pin configuration, PIN = V9 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D7;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D8 pin configuration, PIN = W9 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D8;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D9 pin configuration, PIN = P11 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D9;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D10 pin configuration, PIN = V10 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D10;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D11 pin configuration, PIN = Y10 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D11;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D12 pin configuration, PIN = W10 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D12;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D13 pin configuration, PIN = R11 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D13;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D14 pin configuration, PIN = V11 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D14;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D15 pin configuration, PIN = W11 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D15;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D16 pin configuration, PIN = P12 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D16;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_D17 pin configuration, PIN = R12 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D17;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_PCLK pin configuration, PIN = W6 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_PCLK;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_VSYNC pin configuration, PIN = V7 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_VSYNC;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_HSYNC pin configuration, PIN = Y6 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_HSYNC;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* LCD_ACBIAS pin configuration, PIN = W7 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_ACBIAS;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-}
-
-/****************************************
- * Routine: muxSetupCamera (ostboot)
- * Description: Setup camera muxing
- *****************************************/
-void muxSetupCamera(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* CAMERA_RSTZ pin configuration, PIN = Y16 */
- /* CAM_RST is connected through the I2C IO expander.*/
- /* MuxConfigReg = (volatile unsigned char *), CONTROL_PADCONF_SYS_NRESWARM*/
- /* *MuxConfigReg = 0x00 ; / * Mode = 0, PUPD=Disabled */
-
- /* CAMERA_XCLK pin configuration, PIN = U3 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_XCLK;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_LCLK pin configuration, PIN = V5 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_LCLK;
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_VSYNC pin configuration, PIN = U2 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_VS,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_HSYNC pin configuration, PIN = T3 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_HS,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT0 pin configuration, PIN = T4 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D0,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT1 pin configuration, PIN = V2 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D1,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT2 pin configuration, PIN = V3 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D2,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT3 pin configuration, PIN = U4 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D3,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT4 pin configuration, PIN = W2 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D4,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT5 pin configuration, PIN = V4 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D5,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT6 pin configuration, PIN = W3 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D6,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT7 pin configuration, PIN = Y2 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D7,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT8 pin configuration, PIN = Y4 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D8,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* CAMERA_DAT9 pin configuration, PIN = V6 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_CAM_D9,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-}
-
-/****************************************
- * Routine: muxSetupMMCSD (ostboot)
- * Description: set up MMC muxing
- *****************************************/
-void muxSetupMMCSD(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* SDMMC_CLKI pin configuration, PIN = H15 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKI,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_CLKO pin configuration, PIN = G19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKO,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_CMD pin configuration, PIN = H18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
- /* External pull-ups are present. */
- /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
-
- /* SDMMC_DAT0 pin configuration, PIN = F20 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT0,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
- /* External pull-ups are present. */
- /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
-
- /* SDMMC_DAT1 pin configuration, PIN = H14 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT1,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
- /* External pull-ups are present. */
- /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
-
- /* SDMMC_DAT2 pin configuration, PIN = E19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT2,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
- /* External pull-ups are present. */
- /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
-
- /* SDMMC_DAT3 pin configuration, PIN = D19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT3,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
- /* External pull-ups are present. */
- /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */
-
- /* SDMMC_DDIR0 pin configuration, PIN = F19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR0,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_DDIR1 pin configuration, PIN = E20 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR1,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_DDIR2 pin configuration, PIN = F18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR2,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_DDIR3 pin configuration, PIN = E18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR3,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SDMMC_CDIR pin configuration, PIN = G18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD_DIR,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* MMC_CD pin configuration, PIN = B3 ---2420IP ONLY---*/
- /* MMC_CD for 2422IP=K1 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SDRC_A14,
- *MuxConfigReg = 0x03 ; /* Mode = 3, PUPD=Disabled */
-
- /* MMC_WP pin configuration, PIN = B4 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SDRC_A13,
- *MuxConfigReg = 0x03 ; /* Mode = 3, PUPD=Disabled */
-}
-
-/******************************************
- * Routine: muxSetupTouchScreen (ostboot)
- * Description: Set up touch screen muxing
- *******************************************/
-void muxSetupTouchScreen(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* SPI1_CLK pin configuration, PIN = U18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_CLK,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SPI1_MOSI pin configuration, PIN = V20 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SIMO,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SPI1_MISO pin configuration, PIN = T18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SOMI,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* SPI1_nCS0 pin configuration, PIN = U19 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_NCS0,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-
- /* PEN_IRQ pin configuration, PIN = P20 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MCBSP1_FSR,
- *MuxConfigReg = 0x03 ; /* Mode = 3, PUPD=Disabled */
-}
-
-/****************************************
- * Routine: muxSetupHDQ (ostboot)
- * Description: setup 1wire mux
- *****************************************/
-void muxSetupHDQ(void)
-{
- volatile unsigned char *MuxConfigReg;
-
- /* HDQ_SIO pin configuration, PIN = N18 */
- MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_HDQ_SIO,
- *MuxConfigReg = 0x00 ; /* Mode = 0, PUPD=Disabled */
-}
-
-/***************************************************************
- * Routine: muxSetupGPMC (ostboot)
- * Description: Configures balls which cam up in protected mode
- ***************************************************************/
-void muxSetupGPMC(void)
-{
- volatile uint8 *MuxConfigReg;
- volatile unsigned int *MCR = (volatile unsigned int *)0x4800008C;
-
- /* gpmc_io_dir */
- *MCR = 0x19000000;
-
- /* NOR FLASH CS0 */
- /* signal - Gpmc_clk; pin - J4; offset - 0x0088; mode - 0; Byte-3 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_D2_BYTE3,
- *MuxConfigReg = 0x00 ;
-
- /* signal - Gpmc_iodir; pin - n2; offset - 0x008C; mode - 1; Byte-3 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE3,
- *MuxConfigReg = 0x01 ;
-
- /* MPDB(Multi Port Debug Port) CS1 */
- /* signal - gpmc_ncs1; pin - N8; offset - 0x008C; mode - 0; Byte-1 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE1,
- *MuxConfigReg = 0x00 ;
-
- /* signal - Gpmc_ncs2; pin - E2; offset - 0x008C; mode - 0; Byte-2 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE2,
- *MuxConfigReg = 0x00 ;
-}
-
-/****************************************************************
- * Routine: muxSetupSDRC (ostboot)
- * Description: Configures balls which come up in protected mode
- ****************************************************************/
-void muxSetupSDRC(void)
-{
- volatile uint8 *MuxConfigReg;
-
- /* signal - sdrc_ncs1; pin - C12; offset - 0x00A0; mode - 0; Byte-1 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_NCS0_BYTE1,
- *MuxConfigReg = 0x00 ;
-
- /* signal - sdrc_a12; pin - D11; offset - 0x0030; mode - 0; Byte-2 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_A14_BYTE2,
- *MuxConfigReg = 0x00 ;
-
- /* signal - sdrc_cke1; pin - B13; offset - 0x00A0; mode - 0; Byte-3 Pull/up - N/A */
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_NCS0_BYTE3,
- *MuxConfigReg = 0x00;
-
- if (get_cpu_type() == CPU_2422) {
- MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_SDRC_A14_BYTE0,
- *MuxConfigReg = 0x1b;
- }
-}
-
-/*****************************************************************************
- * Routine: update_mux()
- * Description: Update balls which are different beween boards. All should be
- * updated to match functionaly. However, I'm only updating ones
- * which I'll be using for now. When power comes into play they
- * all need updating.
- *****************************************************************************/
-void update_mux(u32 btype,u32 mtype)
-{
- u32 cpu, base = OMAP2420_CTRL_BASE;
- cpu = get_cpu_type();
-
- if (btype == BOARD_H4_MENELAUS) {
- if (cpu == CPU_2420) {
- /* PIN = B3, GPIO.0->KBR5, mode 3, (pun?),-DO-*/
- __raw_writeb(0x3, base+0x30);
- /* PIN = B13, GPIO.38->KBC6, mode 3, (pun?)-DO-*/
- __raw_writeb(0x3, base+0xa3);
- /* PIN = F1, GPIO.25->HSUSBxx mode 3, (for external HS USB)*/
- /* PIN = H1, GPIO.26->HSUSBxx mode 3, (for external HS USB)*/
- /* PIN = K1, GPMC_ncs6 mode 0, (on board nand access)*/
- /* PIN = L2, GPMC_ncs67 mode 0, (for external HS USB)*/
- /* PIN = M1 (HSUSBOTG) */
- /* PIN = P1, GPIO.35->MEN_POK mode 3, (menelaus powerok)-DO-*/
- __raw_writeb(0x3, base+0x9d);
- /* PIN = U32, (WLAN_CLKREQ) */
- /* PIN = Y11, WLAN */
- /* PIN = AA4, GPIO.15->KBC2, mode 3, -DO- */
- __raw_writeb(0x3, base+0xe7);
- /* PIN = AA8, mDOC */
- /* PIN = AA10, BT */
- /* PIN = AA13, WLAN */
- /* PIN = M18 GPIO.96->MMC2_WP mode 3 -DO- */
- __raw_writeb(0x3, base+0x10e);
- /* PIN = N19 GPIO.98->WLAN_INT mode 3 -DO- */
- __raw_writeb(0x3, base+0x110);
- /* PIN = J15 HHUSB */
- /* PIN = H19 HSUSB */
- /* PIN = W13, P13, R13, W16 ... */
- /* PIN = V12 GPIO.25->I2C_CAMEN mode 3 -DO- */
- __raw_writeb(0x3, base+0xde);
- /* PIN = W19 sys_nirq->MENELAUS_INT mode 0 -DO- */
- __raw_writeb(0x0, base+0x12c);
- /* PIN = AA17->sys_clkreq mode 0 -DO- */
- __raw_writeb(0x0, base+0x136);
- } else if (cpu == CPU_2422) {
- /* PIN = B3, GPIO.0->nc, mode 3, set above (pun?)*/
- /* PIN = B13, GPIO.cke1->nc, mode 0, set above, (pun?)*/
- /* PIN = F1, GPIO.25->HSUSBxx mode 3, (for external HS USB)*/
- /* PIN = H1, GPIO.26->HSUSBxx mode 3, (for external HS USB)*/
- /* PIN = K1, GPMC_ncs6 mode 0, (on board nand access)*/
- __raw_writeb(0x0, base+0x92);
- /* PIN = L2, GPMC_ncs67 mode 0, (for external HS USB)*/
- /* PIN = M1 (HSUSBOTG) */
- /* PIN = P1, GPIO.35->MEN_POK mode 3, (menelaus powerok)-DO-*/
- __raw_writeb(0x3, base+0x10c);
- /* PIN = U32, (WLAN_CLKREQ) */
- /* PIN = AA4, GPIO.15->KBC2, mode 3, -DO- */
- __raw_writeb(0x3, base+0x30);
- /* PIN = AA8, mDOC */
- /* PIN = AA10, BT */
- /* PIN = AA12, WLAN */
- /* PIN = M18 GPIO.96->MMC2_WP mode 3 -DO- */
- __raw_writeb(0x3, base+0x10e);
- /* PIN = N19 GPIO.98->WLAN_INT mode 3 -DO- */
- __raw_writeb(0x3, base+0x110);
- /* PIN = J15 HHUSB */
- /* PIN = H19 HSUSB */
- /* PIN = W13, P13, R13, W16 ... */
- /* PIN = V12 GPIO.25->I2C_CAMEN mode 3 -DO- */
- __raw_writeb(0x3, base+0xde);
- /* PIN = W19 sys_nirq->MENELAUS_INT mode 0 -DO- */
- __raw_writeb(0x0, base+0x12c);
- /* PIN = AA17->sys_clkreq mode 0 -DO- */
- __raw_writeb(0x0, base+0x136);
- }
-
- } else if (btype == BOARD_H4_SDP) {
- if (cpu == CPU_2420) {
- /* PIN = B3, GPIO.0->nc mode 3, set above (pun?)*/
- /* PIN = B13, GPIO.cke1->nc, mode 0, set above, (pun?)*/
- /* Pin = Y11 VLNQ */
- /* Pin = AA4 VLNQ */
- /* Pin = AA6 VLNQ */
- /* Pin = AA8 VLNQ */
- /* Pin = AA10 VLNQ */
- /* Pin = AA12 VLNQ */
- /* PIN = M18 GPIO.96->KBR5 mode 3 -DO- */
- __raw_writeb(0x3, base+0x10e);
- /* PIN = N19 GPIO.98->KBC6 mode 3 -DO- */
- __raw_writeb(0x3, base+0x110);
- /* PIN = J15 MDOC_nDMAREQ */
- /* PIN = H19 GPIO.100->KBC2 mode 3 -DO- */
- __raw_writeb(0x3, base+0x114);
- /* PIN = W13, V12, P13, R13, W19, W16 ... */
- /* PIN = AA17 sys_clkreq->bt_clk_req mode 0 */
- } else if (cpu == CPU_2422) {
- /* PIN = B3, GPIO.0->MMC_CD, mode 3, set above */
- /* PIN = B13, GPIO.38->wlan_int, mode 3, (pun?)*/
- /* Pin = Y11 VLNQ */
- /* Pin = AA4 VLNQ */
- /* Pin = AA6 VLNQ */
- /* Pin = AA8 VLNQ */
- /* Pin = AA10 VLNQ */
- /* Pin = AA12 VLNQ */
- /* PIN = M18 GPIO.96->KBR5 mode 3 -DO- */
- __raw_writeb(0x3, base+0x10e);
- /* PIN = N19 GPIO.98->KBC6 mode 3 -DO- */
- __raw_writeb(0x3, base+0x110);
- /* PIN = J15 MDOC_nDMAREQ */
- /* PIN = H19 GPIO.100->KBC2 mode 3 -DO- */
- __raw_writeb(0x3, base+0x114);
- /* PIN = W13, V12, P13, R13, W19, W16 ... */
- /* PIN = AA17 sys_clkreq->bt_clk_req mode 0 */
- }
- }
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_LAN91C96
- rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);
-#endif
- return rc;
-}
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/arch/omap2420.h>
-#include <asm/io.h>
-#include <asm/arch/bits.h>
-#include <asm/arch/mem.h> /* get mem tables */
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/sys_info.h>
-#include <i2c.h>
-
-/**************************************************************************
- * get_prod_id() - get id info from chips
- ***************************************************************************/
-static u32 get_prod_id(void)
-{
- u32 p;
- p = __raw_readl(PRODUCTION_ID); /* get production ID */
- return((p & CPU_242X_PID_MASK) >> 16);
-}
-
-/**************************************************************************
- * get_cpu_type() - low level get cpu type
- * - no C globals yet.
- * - just looking to say if this is a 2422 or 2420 or ...
- * - to start with we will look at switch settings..
- * - 2422 id's same as 2420 for ES1 will rely on H4 board characteristics
- * (mux for 2420, non-mux for 2422).
- ***************************************************************************/
-u32 get_cpu_type(void)
-{
- u32 v;
-
- switch(get_prod_id()){
- case 1:;/* 2420 */
- case 2: return(CPU_2420); break; /* 2420 pop */
- case 4: return(CPU_2422); break;
- case 8: return(CPU_2423); break;
- default: break; /* early 2420/2422's unmarked */
- }
-
- v = __raw_readl(TAP_IDCODE_REG);
- v &= CPU_24XX_ID_MASK;
- if (v == CPU_2420_CHIPID) { /* currently 2420 and 2422 have same id */
- if (is_gpmc_muxed() == GPMC_MUXED) /* if mux'ed */
- return(CPU_2420);
- else
- return(CPU_2422);
- } else
- return(CPU_2420); /* don't know, say 2420 */
-}
-
-/******************************************
- * get_cpu_rev(void) - extract version info
- ******************************************/
-u32 get_cpu_rev(void)
-{
- u32 v;
- v = __raw_readl(TAP_IDCODE_REG);
- v = v >> 28;
- return(v+1); /* currently 2422 and 2420 match up */
-}
-/****************************************************
- * is_mem_sdr() - return 1 if mem type in use is SDR
- ****************************************************/
-u32 is_mem_sdr(void)
-{
- volatile u32 *burst = (volatile u32 *)(SDRC_MR_0+SDRC_CS0_OSET);
- if(*burst == H4_2420_SDRC_MR_0_SDR)
- return(1);
- return(0);
-}
-
-/***********************************************************
- * get_mem_type() - identify type of mDDR part used.
- * 2422 uses stacked DDR, 2 parts CS0/CS1.
- * 2420 may have 1 or 2, no good way to know...only init 1...
- * when eeprom data is up we can select 1 more.
- *************************************************************/
-u32 get_mem_type(void)
-{
- u32 cpu, sdr = is_mem_sdr();
-
- cpu = get_cpu_type();
- if (cpu == CPU_2422 || cpu == CPU_2423)
- return(DDR_STACKED);
-
- if(get_prod_id() == 0x2)
- return(XDR_POP);
-
- if (get_board_type() == BOARD_H4_MENELAUS)
- if(sdr)
- return(SDR_DISCRETE);
- else
- return(DDR_COMBO);
- else
- if(sdr) /* SDP + SDR kit */
- return(SDR_DISCRETE);
- else
- return(DDR_DISCRETE); /* origional SDP */
-}
-
-/***********************************************************************
- * get_cs0_size() - get size of chip select 0/1
- ************************************************************************/
-u32 get_sdr_cs_size(u32 offset)
-{
- u32 size;
- size = __raw_readl(SDRC_MCFG_0+offset) >> 8; /* get ram size field */
- size &= 0x2FF; /* remove unwanted bits */
- size *= SZ_2M; /* find size in MB */
- return(size);
-}
-
-/***********************************************************************
- * get_board_type() - get board type based on current production stats.
- * --- NOTE: 2 I2C EEPROMs will someday be populated with proper info.
- * when they are available we can get info from there. This should
- * be correct of all known boards up until today.
- ************************************************************************/
-u32 get_board_type(void)
-{
- if (i2c_probe(I2C_MENELAUS) == 0)
- return(BOARD_H4_MENELAUS);
- else
- return(BOARD_H4_SDP);
-}
-
-/******************************************************************
- * get_sysboot_value() - get init word settings (dip switch on h4)
- ******************************************************************/
-inline u32 get_sysboot_value(void)
-{
- return(0x00000FFF & __raw_readl(CONTROL_STATUS));
-}
-
-/***************************************************************************
- * get_gpmc0_base() - Return current address hardware will be
- * fetching from. The below effectively gives what is correct, its a bit
- * mis-leading compared to the TRM. For the most general case the mask
- * needs to be also taken into account this does work in practice.
- * - for u-boot we currently map:
- * -- 0 to nothing,
- * -- 4 to flash
- * -- 8 to enent
- * -- c to wifi
- ****************************************************************************/
-u32 get_gpmc0_base(void)
-{
- u32 b;
-
- b = __raw_readl(GPMC_CONFIG7_0);
- b &= 0x1F; /* keep base [5:0] */
- b = b << 24; /* ret 0x0b000000 */
- return(b);
-}
-
-/*****************************************************************
- * is_gpmc_muxed() - tells if address/data lines are multiplexed
- *****************************************************************/
-u32 is_gpmc_muxed(void)
-{
- u32 mux;
- mux = get_sysboot_value();
- if ((mux & (BIT0 | BIT1 | BIT2 | BIT3)) == (BIT0 | BIT2 | BIT3))
- return(GPMC_MUXED); /* NAND Boot mode */
- if (mux & BIT1) /* if mux'ed */
- return(GPMC_MUXED);
- else
- return(GPMC_NONMUXED);
-}
-
-/************************************************************************
- * get_gpmc0_type() - read sysboot lines to see type of memory attached
- ************************************************************************/
-u32 get_gpmc0_type(void)
-{
- u32 type;
- type = get_sysboot_value();
- if ((type & (BIT3|BIT2)) == (BIT3|BIT2))
- return(TYPE_NAND);
- else
- return(TYPE_NOR);
-}
-
-/*******************************************************************
- * get_gpmc0_width() - See if bus is in x8 or x16 (mainly for nand)
- *******************************************************************/
-u32 get_gpmc0_width(void)
-{
- u32 width;
- width = get_sysboot_value();
- if ((width & 0xF) == (BIT3|BIT2))
- return(WIDTH_8BIT);
- else
- return(WIDTH_16BIT);
-}
-
-/*********************************************************************
- * wait_on_value() - common routine to allow waiting for changes in
- * volatile regs.
- *********************************************************************/
-u32 wait_on_value(u32 read_bit_mask, u32 match_value, u32 read_addr, u32 bound)
-{
- u32 i = 0, val;
- do {
- ++i;
- val = __raw_readl(read_addr) & read_bit_mask;
- if (val == match_value)
- return(1);
- if (i==bound)
- return(0);
- } while (1);
-}
-
-/*********************************************************************
- * display_board_info() - print banner with board info.
- *********************************************************************/
-void display_board_info(u32 btype)
-{
- static const char cpu_2420 [] = "2420"; /* cpu type */
- static const char cpu_2422 [] = "2422";
- static const char cpu_2423 [] = "2423";
- static const char db_men [] = "Menelaus"; /* board type */
- static const char db_ip [] = "IP";
- static const char mem_sdr [] = "mSDR"; /* memory type */
- static const char mem_ddr [] = "mDDR";
- static const char t_tst [] = "TST"; /* security level */
- static const char t_emu [] = "EMU";
- static const char t_hs [] = "HS";
- static const char t_gp [] = "GP";
- static const char unk [] = "?";
-
- const char *cpu_s, *db_s, *mem_s, *sec_s;
- u32 cpu, rev, sec;
-
- rev = get_cpu_rev();
- cpu = get_cpu_type();
- sec = get_device_type();
-
- if(is_mem_sdr())
- mem_s = mem_sdr;
- else
- mem_s = mem_ddr;
-
- if(cpu == CPU_2423)
- cpu_s = cpu_2423;
- else if (cpu == CPU_2422)
- cpu_s = cpu_2422;
- else
- cpu_s = cpu_2420;
-
- if(btype == BOARD_H4_MENELAUS)
- db_s = db_men;
- else
- db_s = db_ip;
-
- switch(sec){
- case TST_DEVICE: sec_s = t_tst; break;
- case EMU_DEVICE: sec_s = t_emu; break;
- case HS_DEVICE: sec_s = t_hs; break;
- case GP_DEVICE: sec_s = t_gp; break;
- default: sec_s = unk;
- }
-
- printf("OMAP%s-%s revision %d\n", cpu_s, sec_s, rev-1);
- printf("TI H4 SDP Base Board + %s Daughter Board + %s \n", db_s, mem_s);
-}
-
-/*************************************************************************
- * get_board_rev() - setup to pass kernel board revision information
- * 0 = 242x IP platform (first 2xx boards)
- * 1 = 242x Menelaus platfrom.
- *************************************************************************/
-u32 get_board_rev(void)
-{
- u32 rev = 0;
- u32 btype = get_board_type();
-
- if (btype == BOARD_H4_MENELAUS){
- rev = 1;
- }
- return(rev);
-}
-
-/********************************************************
- * get_base(); get upper addr of current execution
- *******************************************************/
-u32 get_base(void)
-{
- u32 val;
- __asm__ __volatile__("mov %0, pc \n" : "=r" (val) : : "memory");
- val &= 0xF0000000;
- val >>= 28;
- return(val);
-}
-
-/********************************************************
- * get_base2(); get 2upper addr of current execution
- *******************************************************/
-u32 get_base2(void)
-{
- u32 val;
- __asm__ __volatile__("mov %0, pc \n" : "=r" (val) : : "memory");
- val &= 0xFF000000;
- val >>= 24;
- return(val);
-}
-
-/********************************************************
- * running_in_flash() - tell if currently running in
- * flash.
- *******************************************************/
-u32 running_in_flash(void)
-{
- if (get_base() < 4)
- return(1); /* in flash */
- return(0); /* running in SRAM or SDRAM */
-}
-
-/********************************************************
- * running_in_sram() - tell if currently running in
- * sram.
- *******************************************************/
-u32 running_in_sram(void)
-{
- if (get_base() == 4)
- return(1); /* in SRAM */
- return(0); /* running in FLASH or SDRAM */
-}
-/********************************************************
- * running_in_sdram() - tell if currently running in
- * flash.
- *******************************************************/
-u32 running_in_sdram(void)
-{
- if (get_base() > 4)
- return(1); /* in sdram */
- return(0); /* running in SRAM or FLASH */
-}
-
-/*************************************************************
- * running_from_internal_boot() - am I a signed NOR image.
- *************************************************************/
-u32 running_from_internal_boot(void)
-{
- u32 v, base;
-
- v = get_sysboot_value() & BIT3;
- base = get_base2();
- /* if running at mask rom flash address and
- * sysboot3 says this was an internal boot
- */
- if ((base == 0x08) && v)
- return(1);
- else
- return(0);
-}
-
-/*************************************************************
- * get_device_type(): tell if GP/HS/EMU/TST
- *************************************************************/
-u32 get_device_type(void)
-{
- int mode;
- mode = __raw_readl(CONTROL_STATUS) & (BIT10|BIT9|BIT8);
- return(mode >>= 8);
-}
mx35pdk arm arm1136 - freescale mx35
woodburn arm arm1136 - - mx35
woodburn_sd arm arm1136 woodburn - mx35 woodburn_sd:IMX_CONFIG=board/woodburn/imximage.cfg
-omap2420h4 arm arm1136 - ti omap24xx
tnetv107x_evm arm arm1176 tnetv107xevm ti tnetv107x
rpi_b arm arm1176 rpi_b raspberrypi bcm2835
integratorap_cm720t arm arm720t integrator armltd - integratorap:CM720T
CPCI440 powerpc 440GP b568fd2 2007-12-27 Matthias Fuchs <matthias.fuchs@esd-electronics.com>
PCIPPC2 powerpc MPC740/MPC750 7c9e89b 2013-02-07 Wolfgang Denk <wd@denx.de>
PCIPPC6 powerpc MPC740/MPC750 - - Wolfgang Denk <wd@denx.de>
+omap2420h4 arm omap24xx - 2013-06-04 Richard Woodruff <r-woodruff2@ti.com>
defined(CONFIG_AM33XX) || defined(CONFIG_SOC_DA8XX) || \
defined(CONFIG_TI814X)
-#if defined(CONFIG_APTIX)
- /* /13 mode so Aptix 6MHz can hit 115200 */
- serial_out(3, &com_port->mdr1);
-#else
/* /16 is proper to hit 115200 with 48MHz */
serial_out(0, &com_port->mdr1);
-#endif
#endif /* CONFIG_OMAP */
}
}
#endif
-#ifdef CONFIG_APTIX
-#define MODE_X_DIV 13
-#else
#define MODE_X_DIV 16
-#endif
-
/* Compute divisor value. Normally, we should simply return:
* CONFIG_SYS_NS16550_CLK) / MODE_X_DIV / gd->baudrate
* but we need to round that value by adding 0.5.
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Texas Instruments.
- * Richard Woodruff <r-woodruff2@ti.com>
- * Kshitij Gupta <kshitij@ti.com>
- *
- * Configuration settings for the 242x TI H4 board.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */
-#define CONFIG_OMAP 1 /* in a TI OMAP core */
-#define CONFIG_OMAP2420 1 /* which is in a 2420 */
-#define CONFIG_OMAP2420H4 1 /* and on a H4 board */
-/*#define CONFIG_APTIX 1 #* define if on APTIX test chip */
-/*#define CONFIG_VIRTIO 1 #* Using Virtio simulator */
-
-#define CONFIG_STANDALONE_LOAD_ADDR 0x80300000
-
-/* Clock config to target*/
-#define PRCM_CONFIG_II 1
-/* #define PRCM_CONFIG_III 1 */
-
-#include <asm/arch/omap2420.h> /* get chip and board defs */
-
-/* On H4, NOR and NAND flash are mutual exclusive.
- Define this if you want to use NAND
- */
-/*#define CONFIG_SYS_NAND_BOOT */
-
-#ifdef CONFIG_APTIX
-#define V_SCLK 1500000
-#else
-#define V_SCLK 12000000
-#endif
-
-/* input clock of PLL */
-/* the OMAP2420 H4 has 12MHz, 13MHz, or 19.2Mhz crystal input */
-#define CONFIG_SYS_CLK_FREQ V_SCLK
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-#define CONFIG_REVISION_TAG 1
-#define CONFIG_OF_LIBFDT
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size of Environment Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
-
-/*
- * Hardware drivers
- */
-
-/*
- * SMC91c96 Etherent
- */
-#define CONFIG_LAN91C96
-#define CONFIG_LAN91C96_BASE (H4_CS1_BASE+0x300)
-#define CONFIG_LAN91C96_EXT_PHY
-
-/*
- * NS16550 Configuration
- */
-#ifdef CONFIG_APTIX
-#define V_NS16550_CLK (6000000) /* 6MHz in current MaxSet */
-#else
-#define V_NS16550_CLK (48000000) /* 48MHz (APLL96/2) */
-#endif
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK /* 3MHz (1.5MHz*2) */
-#define CONFIG_SYS_NS16550_COM1 OMAP2420_UART1
-
-/*
- * select serial console configuration
- */
-#define CONFIG_SERIAL1 1 /* UART1 on H4 */
-
- /*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 1
-#define CONFIG_DRIVER_OMAP24XX_I2C
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#ifdef CONFIG_SYS_NAND_BOOT
- #define CONFIG_CMD_DHCP
- #define CONFIG_CMD_I2C
- #define CONFIG_CMD_NAND
- #define CONFIG_CMD_JFFS2
-#else
- #define CONFIG_CMD_DHCP
- #define CONFIG_CMD_I2C
- #define CONFIG_CMD_JFFS2
-
- #undef CONFIG_CMD_SOURCE
-#endif
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-
-#define CONFIG_BOOTDELAY 3
-
-#ifdef NFS_BOOT_DEFAULTS
-#define CONFIG_BOOTARGS "mem=32M console=ttyS0,115200n8 noinitrd root=/dev/nfs rw nfsroot=128.247.77.158:/home/a0384864/wtbu/rootfs ip=dhcp"
-#else
-#define CONFIG_BOOTARGS "root=/dev/ram0 rw mem=32M console=ttyS0,115200n8 initrd=0x80600000,8M ramdisk_size=8192"
-#endif
-
-#define CONFIG_NETMASK 255.255.254.0
-#define CONFIG_IPADDR 128.247.77.90
-#define CONFIG_SERVERIP 128.247.77.158
-#define CONFIG_BOOTFILE "uImage"
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#ifdef CONFIG_APTIX
-# define CONFIG_SYS_PROMPT "OMAP2420 Aptix # "
-#else
-# define CONFIG_SYS_PROMPT "OMAP242x H4 # "
-#endif
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START (OMAP2420_SDRC_CS0) /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END (OMAP2420_SDRC_CS0+SZ_31M)
-
-#define CONFIG_SYS_LOAD_ADDR (OMAP2420_SDRC_CS0) /* default load address */
-
-/* The 2420 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
- * 32KHz clk, or from external sig. This rate is divided by a local divisor.
- */
-#ifdef CONFIG_APTIX
-#define V_PTV 3
-#else
-#define V_PTV 7 /* use with 12MHz/128 */
-#endif
-
-#define CONFIG_SYS_TIMERBASE OMAP2420_GPT2
-#define CONFIG_SYS_PTV V_PTV /* 2^(PTV+1) */
-#define CONFIG_SYS_HZ 1000
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-#define PHYS_SDRAM_1 OMAP2420_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
-#define PHYS_SDRAM_2 OMAP2420_SDRC_CS1
-
-#define PHYS_FLASH_SECT_SIZE SZ_128K
-#define PHYS_FLASH_1 H4_CS0_BASE /* Flash Bank #1 */
-#define PHYS_FLASH_SIZE_1 SZ_32M
-#define PHYS_FLASH_2 (H4_CS0_BASE+SZ_32M) /* same cs, 2 chips in series */
-#define PHYS_FLASH_SIZE_2 SZ_32M
-
-#define PHYS_SRAM 0x4020F800
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT (259) /* max number of sectors on one chip */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */
-#define CONFIG_SYS_MONITOR_LEN SZ_128K /* Reserve 1 sector */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + PHYS_FLASH_SIZE_1 }
-
-#ifdef CONFIG_SYS_NAND_BOOT
-#define CONFIG_ENV_IS_IN_NAND 1
-#define CONFIG_ENV_OFFSET 0x80000 /* environment starts here */
-#else
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + SZ_256K)
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE
-#define CONFIG_ENV_OFFSET ( CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN ) /* Environment after Monitor */
-#endif
-
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-
-#define CONFIG_SYS_JFFS2_MEM_NAND
-
-/*
- * JFFS2 partitions
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nor1"
-#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT "nor1=omap2420-1"
-#define MTDPARTS_DEFAULT "mtdparts=omap2420-1:-(jffs2)"
-*/
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR PHYS_SRAM
-
-#endif /* __CONFIG_H */
projects / project / bcm63xx / u-boot.git / commitdiff